Advantech MIO-6300 User manual

User Manual
MIO-6300
Intel® Celeron® N2930 3.5"
Robotics application, DDR3L,
18/24-bit LVDS, VGA, 3 GbE, 2
Full-size Mini PCIe, SMBus, I2C,
mSATA , 12V/24V Power Input,
CANBus support.

MIO-6300 User Manual ii
Copyright
The documentation and the software included with this product are copyrighted 2016
by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right
to make improvements in the products described in this manual at any time without
notice.
No part of this manual may be reproduced, copied, translated or transmitted in any
form or by any means without the prior written permission of Advantech Co., Ltd.
Information provided in this manual is intended to be accurate and reliable. However,
Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringements
of the rights of third parties, which may result from its use.
Acknowledgements
AMI is a trademark of AMI Software International, Inc.
Intel®is a trademark of Intel®Technologies, Inc.
IBM, PC/AT, PS/2 and VGA are trademarks of International Business Machines Cor-
poration.
Intel®and Atom™ are trademarks of Intel®Corporation.
Microsoft®Windows®is a registered trademark of Microsoft Corp.
All other product names or trademarks are properties of their respective owners.
Part No. 2006630010 Edition 1
Printed in China August 2016

iii MIO-6300 User Manual
Product Warranty (2 years)
Advantech warrants to you, the original purchaser, that each of its products will be
free from defects in materials and workmanship for two years from the date of pur-
chase.
This warranty does not apply to any products which have been repaired or altered by
persons other than repair personnel authorized by Advantech, or which have been
subject to misuse, abuse, accident or improper installation. Advantech assumes no
liability under the terms of this warranty as a consequence of such events.
Because of Advantech’s high quality-control standards and rigorous testing, most of
our customers never need to use our repair service. If an Advantech product is defec-
tive, it will be repaired or replaced at no charge during the warranty period. For out-
of-warranty repairs, you will be billed according to the cost of replacement materials,
service time and freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For example, CPU
speed, Advantech products used, other hardware and software used, etc.) Note
anything abnormal and list any onscreen messages you get when the problem
occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return merchandize
authorization) number from your dealer. This allows us to process your return
more quickly.
4. Carefully pack the defective product, a fully-completed Repair and Replacement
Order Card and a photocopy proof of purchase date (such as your sales receipt)
in a shippable container. A product returned without proof of the purchase date
is not eligible for warranty service.
5. Write the RMA number visibly on the outside of the package and ship it prepaid
to your dealer.

MIO-6300 User Manual iv
Declaration of Conformity
CE
This product has passed the CE test for environmental specifications. Test conditions
for passing included the equipment being operated within an industrial enclosure. In
order to protect the product from being damaged by ESD (Electrostatic Discharge)
and EMI leakage, we strongly recommend the use of CE-compliant industrial enclo-
sure products.
FCC Class A
This equipment has been tested and found to comply with the limits for a Class A dig-
ital device, pursuant to Part 15 of the FCC Rules. These limits are designed to pro-
vide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Opera-
tion of this device in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his/her own expense. The
user is advised that any equipment changes or modifications not expressly approved
by the party responsible for compliance would void the compliance to FCC regula-
tions and therefore, the user's authority to operate the equipment.
Technical Support and Assistance
1. Visit the Advantech web site at www.advantech.com/support where you can find
the latest information about the product.
2. Contact your distributor, sales representative, or Advantech's customer service
center for technical support if you need additional assistance. Please have the
following information ready before you call:
–Product name and serial number
–Description of your peripheral attachments
–Description of your software (operating system, version, application software,
etc.)
–A complete description of the problem
–The exact wording of any error messages
Caution! There is a danger of a new battery exploding if it is incorrectly installed.
Do not attempt to recharge, force open, or heat the battery. Replace the
battery only with the same or equivalent type recommended by the man-
ufacturer. Discard used batteries according to the manufacturer's
instructions.

v MIO-6300 User Manual
Packing List
Before installation, please ensure the following items have been shipped:
1 MIO-6300
1 Startup manual
Cables:
Heatsink:
Stud & Screw
Ordering Information
Model Number Description
Optional Accessories
Part No. Description
1960065074N001 Heat Spreader (99.5 x 70.5 x 11.2 mm)
EMCB-200U-MP01E CANBus module
1700024079-01
LAN w/LED cable RJ45-8P8C/2*7P-2.0 15cm (Only for MIO-
3260C, LAN w/LED connector is supported by request)
Part Number Description
PN: 1700018999 1 x COM Cable
PN: 1700019000 1 x USB Cable
1960063455T001 99.5 x 70.5 x 15.7 mm
Part Number Description
9666226200E Stud and screw pack, including:
1935031500 Screw R/S D=5.3 H=2 + M3*15L, 4 pcs
1910002303 POST F=M3*5.0L M=M3*4L B=5.0 H=8.0 Cu, 4 pcs
193B0204C0 Screw F/S D=3.5 H=0.8 + M2*4L, 2 pcs
MIO-6300N-S8A1E Intel® Celeron® SoC N2930, fanless, LVDS, mSATA,
mini PCIe, MIOe, 64-pin

MIO-6300 User Manual vi
Safety Instructions
1. Read these safety instructions carefully.
2. Keep this User Manual for later reference.
3. Disconnect this equipment from any AC outlet before cleaning. Use a damp
cloth. Do not use liquid or spray detergents for cleaning.
4. For plug-in equipment, the power outlet socket must be located near the equip-
ment and must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or letting
it fall may cause damage.
7. The openings on the enclosure are for air convection. Protect the equipment
from overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.
9. Position the power cord so that people cannot step on it. Do not place anything
over the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the power source
to avoid damage by transient overvoltage.
12. Never pour any liquid into an opening. This may cause fire or electrical shock.
13. Never open the equipment. For safety reasons, the equipment should be
opened only by qualified service personnel.
14. If one of the following situations arises, get the equipment checked by service
personnel:
The power cord or plug is damaged.
Liquid has penetrated into the equipment.
The equipment has been exposed to moisture.
The equipment does not work well, or you cannot get it to work according to
the user's manual.
The equipment has been dropped and damaged.
The equipment has obvious signs of breakage.
15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE
STORAGE TEMPERATURE MAY GO BELOW -20° C (-4° F) OR ABOVE 60° C
(140° F). THIS COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT
SHOULD BE IN A CONTROLLED ENVIRONMENT.
16. CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY
REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE
RECOMMENDED BY THE MANUFACTURER, DISCARD USED BATTERIES
ACCORDING TO THE MANUFACTURER'S INSTRUCTIONS.
The sound pressure level at the operator's position according to IEC 704-1:1982 is
no more than 70 dB (A).
DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech
disclaims all responsibility for the accuracy of any statements contained herein.

vii MIO-6300 User Manual
Safety Precaution - Electricity
Follow these simple precautions to protect yourself from harm and the products from
damage.
To avoid electrical shock, always disconnect the power from your PC chassis
before you work on it. Don't touch any components on the CPU card or other
cards while the PC is on.
ESD (electrostatic discharge) can cause either catastrophic or latent damage in
sensitive electronic components. Take appropriate measures to ensure that any
accumulated body charge is removed before accessing electronic devices. A
static-safe workbench is ideal.

MIO-6300 User Manual viii

ix MIO-6300 User Manual
Contents
Chapter 1 General Introduction ...........................1
1.1 Introduction ............................................................................................... 2
1.2 Specifications ............................................................................................ 2
1.2.1 General Specifications .................................................................. 2
1.2.2 Functional Specifications .............................................................. 2
1.2.3 Mechanical Specifications............................................................. 3
1.2.4 Electrical Specifications ................................................................ 3
1.2.5 Environmental Specifications........................................................ 3
1.3 Function Block Diagram ............................................................................ 4
Chapter 2 H/W Installation....................................5
2.1 Connectors................................................................................................ 6
2.1.1 Connector List............................................................................... 6
2.1.2 Connector Settings ....................................................................... 6
2.2 Mechanical ................................................................................................ 7
2.2.1 Jumper and Connector Locations ................................................. 7
Figure 2.1 MIO-6300 Connector Location (Top Side).................. 7
Figure 2.2 MIO-6300L Connector Location (Bottom Side) .......... 7
2.2.2 Board Dimensions......................................................................... 8
Figure 2.3 MIO-6300 Mechanical Drawing (Top View)................ 8
Figure 2.4 MIO-6300 Mechanical Drawing (Bottom View)........... 8
Figure 2.5 MIO-6300 Mechanical Drawing (Side View)............... 9
Figure 2.6 MIO-6300 Mechanical Drawing (Side View with Heat-
sink) ............................................................................ 9
2.2.3 Quick Installation Guide ................................................................ 9
2.2.4 Another Thermal Solution - Heat Spreader................................. 10
Chapter 3 BIOS Settings.....................................11
3.1 BIOS Setup ............................................................................................. 12
3.2 Entering Setup ........................................................................................ 13
3.2.1 Main Setup.................................................................................. 13
3.2.2 Advanced BIOS Features Setup................................................. 14
3.2.3 Chipset Configuration ................................................................. 27
3.2.4 Security ....................................................................................... 36
3.2.5 Boot............................................................................................. 37
3.2.6 Save & Exit ................................................................................. 38
Chapter 4 S/W Introduction & Installation ........39
4.1 S/W Introduction...................................................................................... 40
4.2 Driver Installation .................................................................................... 40
4.2.1 Driver Installation ........................................................................ 40
4.3 Value-Added Software Services ............................................................. 40
4.3.1 SUSI Introduction........................................................................ 40
4.3.2 Software APIs ............................................................................. 40
4.3.3 SUSI Installation ......................................................................... 41
4.3.4 SUSI Sample Programs.............................................................. 43
Appendix A PIN Assignments ...............................57

MIO-6300 User Manual x
A.1 Connectors.............................................................................................. 58
Appendix B WDT & GPIO ...................................... 65
B.1 Watchdog Timer Sample Code............................................................... 66
B.2 GPIO Sample Code ................................................................................ 67
Appendix C System Assignments........................ 69
C.1 System I/O Ports..................................................................................... 70
Table C.1: System I/O Ports ...................................................... 70
C.2 1st MB Memory Map............................................................................... 70
Table C.2: 1st MB Memory Map ................................................ 70
C.3 Interrupt Assignments ............................................................................. 71
Table C.3: Interrupt assignments............................................... 71

Chapter 1
1General Introduction
This chapter gives background
information on the MIO-6300.
Sections include:
Introduction
Product Features
Specifications

MIO-6300 User Manual 2
1.1 Introduction
MIO-6300 is a MIO 3.5" board with embedded Intel® Celeron® N2930 1.83 GHZ pro-
cessor targeted at Robotics applications. MIO-6300 can support DDR3L memory up
to 8 GB and has 24 bit LVDS/VGA, with 3 LAN/1 USB 3.0/ 3 USB2.0/ 2 RS-232/422/
485 /2 full size miniPCIe/12 and 24V power input/ CANBus Support.
1.2 Specifications
1.2.1 General Specifications
CPU: Intel® & Celeron® N2930
BIOS: AMI EFI 64 Mbit Flash BIOS
System Memory: DDR3L, 1333 MHz for N2930, up to 8 GB
Internal I/O Interface: 1 x LVDS and 1 x SATA
Battery: Lithium 3 V / 210 mAH
1.2.2 Functional Specifications
Processor
Celeron® N2930 SoC
Frequency
–N2930 1.83 GHz/ CPU Burst 2.16GHz
Manufacturing Technology: 22 nm
L2 cache: 2 MB (N2930)
Memory Supports DDR3L, 1333 MHz (N2930), up to 8 GB
SODIMM Socket: 204-pin SODIMM socket type *1
Graphic Engine
Directx* 11, OGL 3.0, OCL 1.1, OGL ES 2.0
Hardware decode/ acceleration:
–Encode: H264, MPEG2
–Decode: H264, MPEG2, VC-1, WMV9
Display
LVDS (on board): 18/24 bit, 1440 x 900 at 60 Hz
VGA: 2560 x 1600 at 60 Hz
Dual independent display: LVDS+VGA
Audio
High Definition Audio (HD) ALC-888S codec
Up to 2 channel of PCM (Pulse Code Modulation) audio out-
put
Support Line-out, Line-in
PCI-Express Interface
Lane 1 & 2: MIOe connector
Lane 3: Full-size Mini PCIe connector
Lane 4: Intel i210 GbE controller
SATA Interface SATAII: 1 x mSATA by mini-PCIe Socket
SATAII: 1x SATA (Max. Data transfer rate 300 MB/s)
USB Interface
1 x USB 2.0 & 1 x USB 3.0 port
2 x USB 2.0 by box wafer connector by MIOe connector
Transmission speed up to 480 Mbps (USB 2.0) / 5 Gbps
(USB 3.0)
Power Management
Full ACPI (Advanced Configuration and Power Interface) 3.0
Supports S0, S3, S4, S5
Support wake on LAN
BIOS AMI EFI 64 Mbit Flash BIOS via SPI

3 MIO-6300 User Manual
Chapter 1 General Introduction
1.2.3 Mechanical Specifications
1.2.3.1 Dimensions (mm)
146 x 102 mm (5.7" x 4")
1.2.3.2 Height on top (mm)
26.9 mm (including heatsink and PCB)
1.2.3.3 Height under bottom (mm)
6.8 mm
1.2.3.4 Weight (g)
0.35 kg (0.77 lb), weight of total package
1.2.4 Electrical Specifications
Power Supply Type: Single 12 V DC power input (supports DC power hot plug)
1.2.4.1 Power supply Voltage
Single 12 V input 10%
1.2.4.2 Power Consumption
Typical in Windows 8.1 Pro.:
MIO-6300-S8A1E:4.4W
Max in Windows 8.1 Pro.:
MIO-6300N-S8A1E:7.0W
1.2.4.3 RTC Battery
Typical Voltage: 3.0 V
Normal discharge capacity: 210 mAh
1.2.5 Environmental Specifications
1.2.5.1 Operating Humidity
40 °C @ 95% RH Non-Condensing
1.2.5.2 Operating Temperature
0 ~ 60 °C (32~140 °F)
Ethernet
Controller: Intel®i210 (GbE1)
Compliant with IEEE 802.3, IEEE 802.3u, IEEE 802.3z, IEEE
802.ab
Supports 10/100/1000 Mbps
64pin or box wafer connector
Supports Wake on LAN
Serial ports
Controller: SMSC SCH 3114
2 x RS-232/422/485 serial ports with ESD protection: air gap
± 15 kV, contact ± 8 kV
GPIO
Controller: SMSC SCH 3114
8-Bit (programming) through Super I/O, by 64pin
5 V tolerance
SMBus Box wafer connector
I2C Box Wafer connector

MIO-6300 User Manual 4
1.2.5.3 Storage Humidity
60 °C @ 95% RH Non-Condensing
1.2.5.4 Storage Temperature
-40 ~ 85 °C (-40 ~ 185 °F)
1.3 Function Block Diagram
Intel Celeron
Soc N2930
Coastline
Expansion
connec tor
Super I/O
GPIO Header
Full size
Mini PCIe
1* USB
USB2.0
2 x RS-
232/422/485
SMBus /I2C
SMBus/ I2C
12V DC Input
Converter
TPS54531
VGA
Intel I210
* supported by request
VGA
8-bit GPIO
2 x USB USB2.0
USB 3.0
USB3.0/2.0
24V
1 RJ 45 PCIe
Intel I210
GbE w/ LED
GbE w/ LED
IC
12V
Intel I210
GbE w/ LED
PCIe
PCIe
2 RJ45
Single Channel
DDR3L
1333/1066
SO-DIMM
up to 8GB
12V
Full size
Mini PCIe
USB2.0
PCIe
SATA
USB2.0
SATA II
SATAII 300MB/s

Chapter 2
2H/W Installation
This chapter explains the setup
procedures of the MIO-6300 hard-
ware, including instructions on
setting jumpers and connecting
peripherals, as well as switches,
indicators and mechanical draw-
ings. Be sure to read all safety
precautions before you begin the
installation procedure.

MIO-6300 User Manual 6
2.1 Connectors
2.1.1 Connector List
2.1.2 Connector Settings
2.1.2.1 Battery Connector (BH1)
MIO-6300 supports Lithium 3 V/210 mAH CR2032 battery with wire via battery con-
nector (BH1).
Label Function
CN1 12V power input
CN2 Mini PCIE
CN3 MIOe I/O Module Internal connector
CN6 VGA
CN7 LAN RJ45x2
CN8 LAN RJ45
CN9 SMBus Connector
CN10 GPIO Connector
CN11 Internal USB
CN12 Power button
CN13 Reset button
CN14 COM Connector
CN15 External port USB2.0+USB3.0
CN16 Mini PCIE
Note! How to clear CMOS: (Follow these steps)
1. Turn off system power.
2. Unplug CR2032 battery cable on BH1.
3. Wait for 15 secs, or short BH1 pin1-2.
4. Connect battery cable on BH1.
5. Turn on system power.

7 MIO-6300 User Manual
Chapter 2 H/W Installation
2.2 Mechanical
2.2.1 Jumper and Connector Locations
Figure 2.1 MIO-6300 Connector Location (Top Side)
Figure 2.2 MIO-6300L Connector Location (Bottom Side)

MIO-6300 User Manual 8
2.2.2 Board Dimensions
2.2.2.1 CPU Board Drawing
Figure 2.3 MIO-6300 Mechanical Drawing (Top View)
Figure 2.4 MIO-6300 Mechanical Drawing (Bottom View)
unit: mm
33.35
70
R2
27.85
0
9
.
4
1
unit: mm

9 MIO-6300 User Manual
Chapter 2 H/W Installation
Figure 2.5 MIO-6300 Mechanical Drawing (Side View)
Figure 2.6 MIO-6300 Mechanical Drawing (Side View with Heatsink)
2.2.3 Quick Installation Guide
A heatsink is included in the box, please take it out and remove the release paper
from the thermal pads.
unit: mm
6.80
8
1.6
8
1.6
17.80
unit: mm
unit: mm
25.306.80
8 1.6
8
1.6
unit: mm
Removing the releasing paper

MIO-6300 User Manual 10
There are also four screws inside the white box, please install the DRAM in the
SODIMM socket first, then screw the heatsink into place as per illustration below:
2.2.4 Another Thermal Solution - Heat Spreader
MIO-6300 has an optional heat spreader to make whole system more compact.
Using a heat spreader to conduct heat to your chassis can help a lot when the sys-
tem is extra compact or has limited space for heat convection. Here are some guide-
lines for the heat spreader:
1. For best heat conduction, the gap between the chassis and heat spreader
should be small; the smaller the better.
2. The height of the existing heat spreader is 11.2mm (Advantech P/N:
1960065074N001). If you need some other height to fit the chassis better,
Advantech can customize it for you. (Please contact our sales department for
details.)
3. Thermal grease and screws are provided in heat spreader kit. Thermal grease
helps conduction if the chassis is quite close to heat spreader. Another sugges-
tion is to use a thermal pad if the chassis isn't close enough to the heat
spreader. (The gap should be less than 3mm for better heat transfer.)