Advantech PPC-415 6 Series User manual

User Manual
PPC-415/417/419 EHL
15"/17”/19” Color TFT LCD panel
PC with Intel® Atom™ x6425E
Processor

PPC-415/417/419 EHL User Manual ii
Copyright
The documentation and the software included with this product are copyrighted 2023
by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right
to make improvements in the products described in this manual at any time without
notice. No part of this manual may be reproduced, copied, translated, or transmitted
in any form or by any means without the prior written permission of Advantech Co.,
Ltd. The information provided in this manual is intended to be accurate and reliable.
However, Advantech Co., Ltd. assumes no responsibility for its use, nor for any
infringements of the rights of third parties that may result from its use.
Acknowledgements
Intel and Pentium are trademarks of Intel Corporation.
Microsoft Windows is registered trademark of Microsoft Corp.
All other product names or trademarks are properties of their respective owners.
Product Warranty (2 years)
Advantech warrants the original purchaser that each of its products will be free from
defects in materials and workmanship for two years from the date of purchase.
This warranty does not apply to any products that have been repaired or altered by
persons other than repair personnel authorized by Advantech, or products that have
been subject to misuse, abuse, accident, or improper installation. Advantech
assumes no liability under the terms of this warranty as a consequence of such
events.
Because of Advantech’s high quality-control standards and rigorous testing, most
customers never need to use our repair service. If an Advantech product is defective,
it will be repaired or replaced free of charge during the warranty period. For out-of-
warranty repairs, customers will be billed according to the cost of replacement mate-
rials, service time, and freight. Please consult your dealer for more details.
If you believe your product to be defective, follow the steps outlined below.
1. Collect all the information about the problem encountered. (For example, CPU
speed, Advantech products used, other hardware and software used, etc.) Note
anything abnormal and list any onscreen messages displayed when the prob-
lem occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information readily available.
3. If your product is diagnosed as defective, obtain a return merchandise authori-
zation (RMA) number from your dealer. This allows us to process your return
more quickly.
4. Carefully pack the defective product, a completed Repair and Replacement
Order Card, and a proof of purchase date (such as a photocopy of your sales
receipt) into a shippable container. Products returned without a proof of pur-
chase date are not eligible for warranty service.
5. Write the RMA number clearly on the outside of the package and ship the pack-
age prepaid to your dealer.
Part No. 2003041510 Edition 1
Printed in China September 2023

iii PPC-415/417/419 EHL User Manual
Declaration of Conformity
CE
This product has passed the CE test for environmental specifications when shielded
cables are used for external wiring. We recommend the use of shielded cables. This
type of cable is available from Advantech. Please contact your local supplier for
ordering information.
Test conditions for passing also include the equipment being operated within an
industrial enclosure. In order to protect the product from damage caused by electro-
static discharge (ESD) and EMI leakage, we strongly recommend the use of CE-
compliant industrial enclosure products.
FCC Class B
This equipment has been tested and found to comply with the limits for a Class B dig-
ital device, pursuant to part 15 of the FCC Rules. These limits are designed to pro-
vide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. However, there is no guarantee that interfer-
ence will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for assistance.
Technical Support and Assistance
1. Visit the Advantech website at www.advantech.com/support to obtain the latest
product information.
2. Contact your distributor, sales representative, or Advantech's customer service
center for technical support if you need additional assistance. Please have the
following information ready before calling:
–Product name and serial number
–Description of your peripheral attachments
–Description of your software (operating system, version, application software,
etc.)
–A complete description of the problem
–The exact wording of any error messages

PPC-415/417/419 EHL User Manual iv
Safety Instructions
1. Read these safety instructions carefully.
Veuillez lire attentivement ce manuel d'instructions de sécurité.
2. Retain this user manual for future reference.
Veuillez conserver ce manuel d'instructions pour référence ultérieure.
3. Disconnect the equipment from all power outlets before cleaning. Use only a
damp cloth for cleaning. Do not use liquid or spray detergents.
Débranchez l'appareil de toutes les prises de courant avant le nettoyage. Net-
toyez-le uniquement à l'aide d'un chiffon humide. Ne pas utiliser de détergents
liquides ou pulvérisateurs.
4. For pluggable equipment, the power outlet socket must be located near the
equipment and easily accessible.
Pour les appareils enfichables, la prise de courant doit être placée près de
l'appareil et facilement accessible.
5. Protect the equipment from humidity.
Protégez l'appareil contre l'humidité.
6. Place the equipment on a reliable surface during installation. Dropping or letting
the equipment fall may cause damage.
Placez l'appareil sur une surface fiable pendant l'installation. L'abandon ou la
chute de l'appareil pourrait causer des dommages.
7. The openings on the enclosure are for air convection. Protect the equipment
from overheating. Do not cover the openings.
Les ouvertures du boîtier sont pour la convection d'air. Protégez l'appareil con-
tre la surchauffe. Ne couvrez pas les ouvertures.
8. Ensure that the voltage of the power source is correct before connecting the
equipment to a power outlet. The power outlet socket should have grounded
connection.
Assurez-vous que la tension de la source d'alimentation est correcte avant de
connecter l'appareil à une prise de courant. La prise de courant doit avoir une
bonne connexion mise à la terre.
9. Position the power cord away from high-traffic areas. Do not place anything over
the power cord.
Placez le cordon d'alimentation à l'écart des zones à fort trafic. Ne placez rien
sur le cordon d'alimentation.
10. All cautions and warnings on the equipment should be noted.
Attention à toutes les précautions et avertissements indiqués sur l'appareil.
11. If the equipment is not used for a long time, disconnect it from the power source
to avoid damage from transient overvoltage.
Si l'appareil n'est pas utilisé pendant une longue période, déconnectez-le de la
source d'alimentation pour éviter les dommages causés par une surtension
transitoire.
12. Never pour liquid into an opening. This may cause fire or electrical shock.
Ne versez jamais de liquide dans une ouverture. Sinon, cela pourrait provoquer
un incendie ou un choc électrique.
13. Never open the equipment. For safety reasons, the equipment should be
opened only by qualified service personnel.
N'ouvrez jamais l'appareil. Pour des raisons de sécurité, l'appareil ne doit être
ouvert que par un technicien qualifié.
14. If one of the following occurs, have the equipment checked by service person-
nel:
Si l'un des cas suivants se produit, demandez aide à un technicien qualifié:

v PPC-415/417/419 EHL User Manual
The power cord or plug is damaged.
Le cordon d'alimentation ou la fiche est endommagé.
Liquid has penetrated the equipment.
Le liquide a pénétré dans l'appareil.
The equipment has been exposed to moisture.
L'appareil a été exposé à l'humidité.
The equipment is malfunctioning or does not function according to the user
manual.
L'appareil est défectueux ou ne fonctionne pas conformément aux instructions.
The equipment has been dropped or damaged.
L'appareil a été abandonné et endommagé.
The equipment shows obvious signs of breakage.
L'appareil montre des signes évidents de rupture.
15. Do not leave the equipment in an environment with a storage temperature of
below -40 °C (-40 °F) or above 60 °C (140 °F) as this may cause damage. The
equipment should be kept in a controlled environment.
Ne laissez pas cet appareil dans un environnement dont la température de
stockage est inférieure à -40 °C (-40 °F) ou supérieure à 60 °C (140 °F), car
cela pourrait causer des dommages. L'appareil doit être surveillé dans l'envi-
ronnement.
16. CAUTION: Batteries are at risk of exploding if incorrectly replaced. Replace only
with the same or equivalent type as recommended by the manufacturer. Discard
used batteries according to the manufacturer's instructions.
ATTENTION: Il y a danger d'explosion s'il y a remplacement incorrect de la pile.
Remplacer uniquement avec une pile du même type ou d'un type équivalent
recommandé par le constructeur.
17. In accordance with the IEC 704-1:1982 specifications, the sound pressure level
at the operator's position does not exceed 70 dB (A).
Conformément aux spécifications de l'IEC 704-1:1982, le niveau de pression
acoustique à la position de l'opérateur ne dépasse pas 70 dB (A).
18. The equipment is intended to be supplied by a UL-certified power supply
(FSP090-DBBN3 adapter) or DC power source suitable for use at a TMA of at
least 40 °C with the output rated as 19 VDC, 4.74A min., and ES1 (or SELV); or
at a TMA of at least 60 °C with the output rated as 9 ~ 32 VDC, 10~3A min., and
ES1 (or SELV). Contact Advantech for further information.
Le produit doit être alimenté par une alimentation certifiée UL (FSP090-DBBN3
adaptateur) approprié pour l'utilisation à une température de 40 °C au minimum,
et la sortie nominale est 19 VDC, 4.74 A min., ES1 (ou SELV); ou pour l'utilisa-
tion à une température de 60 °C au minimum, et la sortie nominale est 9 ~ 32
VDC, 10~3A min., ES1 (ou SELV). Pour plus d'informations, veuillez contacter
Advantech.
19. DISCLAIMER: These instructions are provided in accordance with IEC 704-1
standards. Advantech disclaims all responsibility for the accuracy of any state-
ments contained herein.
AVERTISSEMENT: Ces instructions sont fournies conformément aux normes
IEC 704-1. Advantech décline toute responsabilité quant à la précision de toute
déclaration contenue dans le présent document.
20. CAUTION: This product is not intended for use by children and is not suitable for
use in locations where children are likely to be present (this product is not a toy).
ATTENTION: Ce produit n'est pas un jouet et devrait être gardé hors de la
portée des enfants.
21. Please Keep the monitor out of direct sunlight, very strong bright lights and
away from any other heat source. Lengthy exposure to this type of environment
may result in discoloration and damage to the monitor.

PPC-415/417/419 EHL User Manual vi
Veuillez ne pas placer les écrans dans le rayonnement solaire direct, dans la
haute lumière et dans d ‘autres sources de chaleur.L ‘exposition prolongée dans
cet environnement peut entraîner la décoloration et l’ endommagement de l ‘affi-
chage.
Safety Precautions - Static Electricity
Follow these simple precautions to protect yourself from harm and the products from
damage.
To avoid electrical shock, always disconnect the power from the PC chassis
before manual handling. Do not touch any components on the CPU card or
other cards while the PC is powered on.
Disconnect the power before making any configuration changes. A sudden rush
of power after connecting a jumper or installing a card may damage sensitive
electronic components.
Power Warning
The power supply is suitable for operation in environments with an altitude of below
5,000 M.
Battery Information
Batteries, battery packs, and accumulators should not be disposed of as unsorted
household waste. Please use the public collection system to return, recycle, or treat
them in compliance with local regulations.

vii PPC-415/417/419 EHL User Manual
Contents
Chapter 1 General Information ............................1
1.1 Introduction ............................................................................................... 2
1.2 Specifications............................................................................................ 2
Table 1.1: Specifications ............................................................. 2
1.3 Dimensions ............................................................................................... 4
Figure 1.1 PPC-415-XX6 Dimensions ......................................... 4
Figure 1.2 PPC-417-XX6 Dimensions ......................................... 4
Figure 1.3 PPC-419-XX6 Dimensions ......................................... 5
Chapter 2 System Installation & Setup ...............7
2.1 Quick Installation Guide ............................................................................ 8
Figure 2.1 PPC-41x-xX6 Series Front Panel ............................... 8
Figure 2.2 Side and Rear View.................................................... 8
Figure 2.3 I/O Connectors ........................................................... 9
2.2 Installation Procedures............................................................................ 10
2.2.1 Connecting the Power Cable ...................................................... 10
Figure 2.4 Power Cable Connector ........................................... 10
2.2.2 Connecting the Keyboard and Mouse......................................... 10
2.3 Memory Card Installation ........................................................................ 11
Figure 2.5 .................................................................................. 11
Figure 2.6 .................................................................................. 11
Figure 2.7 .................................................................................. 12
Figure 2.8 .................................................................................. 12
2.4 SSD Installation....................................................................................... 13
Figure 2.9 .................................................................................. 13
Figure 2.10.................................................................................. 13
Figure 2.11.................................................................................. 14
Figure 2.12.................................................................................. 14
2.5 M.2 Installation ........................................................................................ 15
Figure 2.13.................................................................................. 15
Figure 2.14.................................................................................. 15
Figure 2.15.................................................................................. 16
Figure 2.16.................................................................................. 16
2.6 Wireless LAN Card Installation ............................................................... 17
Figure 2.17.................................................................................. 17
Figure 2.18.................................................................................. 17
Figure 2.19.................................................................................. 18
Figure 2.20.................................................................................. 18
Figure 2.21.................................................................................. 19
Figure 2.22.................................................................................. 19
Figure 2.23.................................................................................. 20
2.7 Install 4G/5G Devices ............................................................................. 21
Figure 2.24.................................................................................. 21
Figure 2.25.................................................................................. 21
Figure 2.26.................................................................................. 22
2.8 Riser Card Installation............................................................................. 23
Figure 2.27.................................................................................. 23
Figure 2.28.................................................................................. 23
2.9 AT/ATX Function Switch ......................................................................... 24
Figure 2.29ATX Mode................................................................. 24
Figure 2.30AT Mode ................................................................... 24
2.10 Mount Bracket Installation....................................................................... 25
Figure 2.31.................................................................................. 25

PPC-415/417/419 EHL User Manual viii
2.11 Cabinet Installation and Grounding......................................................... 26
Figure 2.32Cabinet Installation................................................... 26
Figure 2.33System Wiring Diagram............................................ 26
2.12 Optional Module Installation.................................................................... 27
Figure 2.34 ................................................................................. 27
Figure 2.35 ................................................................................. 27
Figure 2.36 ................................................................................. 28
Figure 2.37 ................................................................................. 28
Figure 2.38 ................................................................................. 29
Figure 2.39 ................................................................................. 29
Figure 2.40 ................................................................................. 30
Figure 2.41 ................................................................................. 30
Figure 2.42 ................................................................................. 31
Figure 2.43 ................................................................................. 31
Chapter 3 Jumper Settings................................ 33
3.1 Jumpers and Connectors........................................................................ 34
Figure 3.1 ................................................................................. 34
Table 3.1: Jumpers and Connectors ......................................... 34
3.1.1 RTC Select ................................................................................. 34
Table 3.2: ................................................................................. 34
3.1.2 ATX/AT Select ............................................................................ 35
Table 3.3: ................................................................................. 35
3.1.3 Power Button Connection ........................................................... 35
Table 3.4: ................................................................................. 35
3.1.4 Touch Power Select.................................................................... 35
Table 3.5: ................................................................................. 35
3.2 External COM Ports and Pin Definitions ................................................. 36
Figure 3.2 ................................................................................. 36
Table 3.6: ................................................................................. 36
3.2.1 COM1 /COM2 Pin 9 Power Select.............................................. 37
Table 3.7: ................................................................................. 37
3.2.2 COM3 ......................................................................................... 37
Table 3.8: ................................................................................. 37
Chapter 4 Software Setup.................................. 39
4.1 Installing Drivers ..................................................................................... 40
4.2 BIOS Setup Utility ................................................................................... 40
4.2.1 Entering BIOS Setup .................................................................. 40
Figure 4.1 ................................................................................. 40
4.2.2 CPU Configuration...................................................................... 41
Figure 4.2 ................................................................................. 41
Figure 4.3 ................................................................................. 41
4.2.3 COM3 Mode Selection (RS422/RS485) ..................................... 42
Figure 4.4 ................................................................................. 42
Figure 4.5 ................................................................................. 43
Figure 4.6 ................................................................................. 43
Figure 4.7 ................................................................................. 44
4.2.4 Hardware Monitor ....................................................................... 45
Figure 4.8 ................................................................................. 45
Figure 4.9 ................................................................................. 45
4.2.5 USB Configuration ...................................................................... 46
Figure 4.10 ................................................................................. 46
4.2.6 SATA configuration..................................................................... 47
Figure 4.11 ................................................................................. 47
Figure 4.12 ................................................................................. 47
4.2.7 Wake-on-LAN ............................................................................. 48

ix PPC-415/417/419 EHL User Manual
Figure 4.13.................................................................................. 48
Figure 4.14.................................................................................. 49
4.2.8 Deep Sleep ................................................................................. 49
Figure 4.15.................................................................................. 49
Figure 4.16.................................................................................. 50
4.2.9 Security....................................................................................... 50
Figure 4.17.................................................................................. 50
4.2.10 Boot............................................................................................. 51
Figure 4.18.................................................................................. 51
4.2.11 Save and Exit.............................................................................. 52
Figure 4.19.................................................................................. 52
Appendix A PCI/PCI-E ............................................53
A.1 PCI/PCI-E................................................................................................ 54

PPC-415/417/419 EHL User Manual x

Chapter 1
1General Information
This chapter gives background
information on the PPC-415/417/
419 panel PC.
Introduction
Specifications
Dimensions

PPC-415/417/419 EHL User Manual 2
1.1 Introduction
Advantech’s PPC-415/417/419 (15”/17”/19”) fanless panel PCs are powered by an
Intel® Atom™ x6425E processor that delivers high-performance computing and sup-
ports a wide operating temperature (-20 ~ 60 °C/-4 ~ 140 °F) and wide power input
range (9 ~ 32 VDC). The provision of multiple I/O interfaces, including four COM (of
which two are internal ports for an optional COM module), two USB 3.2, one isolated
RS-422/485, and dual Intel® Gigabit Ethernet, ensure easy integration of additional
peripherals and convenient deployment. A PCI/PCIe expansion slot is also provided
to support the addition of a fieldbus or proprietary card, increasing the application
potential for a wide range of industries.
1.2 Specifications
Table 1.1: Specifications
Product PPC-415-XX6 PPC-417-XX6 PPC-419-XX6
LCD Specification 15" LCD 17" LCD 19" LCD
Display Type 15" TFT LCD
(LED backlight)
17" TFT LCD
(LED backlight)
19" TFT LCD
(LED Backlight)
Max. Resolution 1024 x 768 1280 x 1024 1280 x 1024
Color 16.7M 16.7M 16.7M
Dot matrix 0.297 x 0.297 mm 0.264 x 0.264 mm 0.294x0.294 mm
Viewing Angle 80 (left), 80 (right),
70 (top), 70 (bottom)
80 (left), 80 (right),
60 (top), 80 (bottom)
85 (left), 85 (right),
80 (up), 80 (down)
Brightness 500 cd/m2 350 cd/m2 350 cd/m2
Contrast 2500 800 1,000
Backlight Lifecycle 70, 000 hours 50, 000 hours 50, 000 hours
Touchscreen 5-wire analog resistive,projected capacitive (by request)
Weight 5.3 kg (11.6 Ib) 6.27 kg (13.9 Ib) 7.9kg (17.3Ib)
Dimensions 396.5 x 317.6 x 65.3(mm)
(15.6" x 12.5" x 2.57")
442.0 x 362.0 x 69.5 (mm)
(17.4" x 14.25" x 2.73")
458.2 x 384 x 67.3(mm)
(18" x 15" x 2.6")
Chipset Intel Atom Processor X6425E
Memory 1 x SODIMM DDR4 3200MHz (max.32GB)
Storage 1 x 2.5” SATA bay
1 x M.2 B key bay (size: 2242/2280 or 3042/3052 mm; Singal: SATA, PCIe
X1, USB 3.0)
Network (LAN) 2 x 10/100/1000/2500 Mbps Ethernet (Intel I226)
I/O Ports
5 x Serial ports: 2 x RS-232, 1 x RS-422/485 with 1K VDC isolation,2 x RS-
232 (on right side optional)
2 x USB 3.2, 3 x USB2.0 (2pcs default, 1pcs optional)
1 x Line-out, 1 x Mic-in, 2 x 1 W speaker (internal)
1 x HDMI 1.4
1 x DP 1.4
1 x GPIO (8 channels, TTL level) (optional)
1 x TPM2.0(internal)
Expansion Slots
1 x PCIe x 1 (default)
1 x PCI (optional)
1 x M.2 2230 E Key slot for wireless card

3 PPC-415/417/419 EHL User Manual
Chapter 1 General Information
Other Expansions CFast card (optional module)
2 x DB9 for two RS-232 or one RS-232 and one GPIO (optional module)
OS Support Microsoft® Windows 10/11(64-bit), Win10 IOT LTSC, Linux
Power Consumption * 50W 60 W 55 W
Input Voltage 9 ~ 32 VDC, 10 A ~ 3 A (19Vdc, 4.74A optional Adapter)
* Test conditions of power consumption for PPC-415-XX6:
Test condition Test Configuration Test System Power Consumption
(W)
Burn-in 8.1
Memory: 8G DDR4
SSD: 64G 2.5”SATAIII
MSATA: MSATA 32G
MLC
IO: COM Port RS232
loopback x 4,
USB 3.2 x 2,USB 2.0 x 2
Window 10 64 bit 50
* Test conditions of power consumption for PPC-417-XX6:
Test condition Test Configuration Test System Power Consumption
(W)
Burn-in 8.1
Memory: 8G DDR4
SSD: 64G 2.5”SATAIII
MSATA: MSATA 32G
MLC
IO: COM Port RS232
loopback x 4,
USB 3.2 x 2,USB 2.0 x 2
Window 10 64 bit 60
* Test conditions of power consumption for PPC-419-XX6:
Test condition Test Configuration Test System Power Consumption
(W)
Burn-in 8.1
Memory: 8G DDR4
SSD: 64G 2.5”SATAIII
MSATA: MSATA 32G
MLC
IO: COM Port RS232
loopback x 4,
USB 3.2 x 2,USB 2.0 x 2
Window 10 64 bit 55
Table 1.1: Specifications

PPC-415/417/419 EHL User Manual 4
1.3 Dimensions
PPC-415-XX6 Series
Figure 1.1 PPC-415-XX6 Dimensions
PPC-417-XX6 Series
Figure 1.2 PPC-417-XX6 Dimensions
Warning! To prevent personal injury and product damage, always use suitable
mounting apparatus.
VESA screw specifications: Type: M4; Screw depth: 8 mm
Warning! To prevent personal injury and product damage, always use suitable
mounting apparatus.
VESA screw specifications: Type: M4; Screw depth: 8 mm











Unit:mm
Panel Cutout Dimensions:382x303(15.03x11.92in)
184.71 75
134.40
75
425
345
357
437
7.50
46.50 56.50
Panel Cutout Dimensions: 427 x 347 mm (16.81 x 13.66 in)

5 PPC-415/417/419 EHL User Manual
Chapter 1 General Information
PPC-419-XX6 Series
Figure 1.3 PPC-419-XX6 Dimensions
Warning! To prevent personal injury and product damage, always use suitable
mounting apparatus.
VESA screw specifications: Type: M4; Screw depth: 8 mm
442
367.80
134.66
57
178.81
75
454
379.80
7.50
52.10
62.10
Panel Cutout Dimensions: 444 x 370 mm (17.48 x 14.56 in)

PPC-415/417/419 EHL User Manual 6

Chapter 2
2System Installation &
Setup
Quick Installation Guide
Installation Procedures
Memory Card Installation
SSD Installation
Mini SATA Installation
Wireless LAN Card Installation
Riser Card Installation
AT/ATX Function Switch
Mount Bracket Installation
Optional Module Installation

PPC-415/417/419 EHL User Manual 8
2.1 Quick Installation Guide
Before setting up the PPC-415/417/419 panel PC, take a moment to familiarize your-
self with the functions and locations of the controls, drives, connectors, and ports (as
shown in the figures below). When placed upright on the desktop, the PPC-415/417/
419 panel PC should appear as shown in Fig. 2.1.
(Note: The figures in this chapter show the PPC-415 model. However, all of the PPC-
41x-xX6 models feature the same design.)
Figure 2.1 PPC-41x-xX6 Series Front Panel
Power status LED: Off (S5) Orange; Sleep (S3) Orange; On (S0) Blue
Figure 2.2 Side and Rear View
LED Indicator
6
1
1
4
2
3
5

9 PPC-415/417/419 EHL User Manual
Chapter 2 System Installation & Setup
1. Antenna holes 2. Panel mount hook holes
3. Speakers (right and left) 4. CPU heatsink
5. Ground screw 6. Optional module expansion slot
I/O Connectors
Figure 2.3 I/O Connectors
A: 1 x Expansion slot (PCI or PCIe x1) G: Power Button
B: Mic-in/Line-Out H: DC jack and AT/ATX switch
C: 2 x Intel Gigabit Ethernet I: 1 x HDMI
D: 1 x DisplayPort J: 2 x USB3.2, 2 x USB2.0
E: 2 x RS-232 K: Optional modules
F: 1 x Isolated RS-422/485
Note! VESA screw specifications: Type: M4; Screw depth: 8 mm
K
AB C D E F G
H
I
J

PPC-415/417/419 EHL User Manual 10
2.2 Installation Procedures
2.2.1 Connecting the Power Cable
The PPC-415/417/419 panel PC features a DC power socket (9 ~ 32 V). When con-
necting the power cable, hold the cable at the plug end.
Follow the procedures outlined below to ensure correct setup.
1. Before connecting the power cable, check that the system’s power mode setting
is configured according to your requirements. To use AT power, flip the AT/ATX
switch (shown below) to AT mode (the default setting is ATX mode).
2. Connect the 2-pin male connector of the power cable (provided in the accessory
box) to the power socket.
Power Button
The power button is located on the bottom right of the panel PC.
Figure 2.4 Power Cable Connector
2.2.2 Connecting the Keyboard and Mouse
Connect the keyboard and mouse to the I/O interfaces located at the rear of the
panel PC.
Note! The power cable and adapter are optional.