Advantech ITA-3630 Series User manual

User Manual
ITA-3630 Series
Intel® Gen2/Gen3 CoreTM i7/i5/
i3 Fanless Dual Core Compact
Industrial Computer with Wide
Voltage Input

ITA-3630 User Manual ii
Copyright
The documentation and the software included with this product are copyrighted 2014
by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right
to make improvements in the products described in this manual at any time without
notice. No part of this manual may be reproduced, copied, translated or transmitted
in any form or by any means without the prior written permission of Advantech Co.,
Ltd. Information provided in this manual is intended to be accurate and reliable. How-
ever, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringe-
ments of the rights of third parties, which may result from its use.
Acknowledgements
The ITA-3630 is trademark of Advantech Co., Ltd.
All other product names or trademarks are properties of their respective owners.
Product Warranty (2 years)
Advantech warrants to you, the original purchaser, that each of its products will be
free from defects in materials and workmanship for two years from the date of pur-
chase.
This warranty does not apply to any products which have been repaired or altered by
persons other than repair personnel authorized by Advantech, or which have been
subject to misuse, abuse, accident or improper installation. Advantech assumes no
liability under the terms of this warranty as a consequence of such events.
Because of Advantech’s high quality-control standards and rigorous testing, most of
our customers never need to use our repair service. If an Advantech product is defec-
tive, it will be repaired or replaced at no charge during the warranty period. For out-
of-warranty repairs, you will be billed according to the cost of replacement materials,
service time and freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For example, CPU
speed, Advantech products used, other hardware and software used, etc.) Note
anything abnormal and list any onscreen messages you get when the problem
occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return merchandize
authorization) number from your dealer. This allows us to process your return
more quickly.
4. Carefully pack the defective product, a fully-completed Repair and Replacement
Order Card and a photocopy proof of purchase date (such as your sales receipt)
in a shippable container. A product returned without proof of the purchase date
is not eligible for warranty service.
5. Write the RMA number visibly on the outside of the package and ship it prepaid
to your dealer.
Part No. 200K363030 Edition 1
Printed in China February 2014

iii ITA-3630 User Manual
Technical Support and Assistance
1. Visit the Advantech website at http://support.advantech.com where you can find
the latest information about the product.
2. Contact your distributor, sales representative, or Advantech's customer service
center for technical support if you need additional assistance. Please have the
following information ready before you call:
–Product name and serial number
–Description of your peripheral attachments
–Description of your software (operating system, version, application software,
etc.)
–A complete description of the problem
–The exact wording of any error messages

ITA-3630 User Manual iv
A Message to the Customer
Advantech Customer Services
Each and every Advantech product is built to the most exacting specifications to
ensure reliable performance in the harsh and demanding conditions typical of indus-
trial environments. Whether your new Advantech equipment is destined for the labo-
ratory or the factory floor, you can be assured that your product will provide
the reliability and ease of operation for which the name Advantech has come
to be known. Your satisfaction is our primary concern. Here is a guide to Advantech's
cus- tomer services.
To ensure you get the full benefit of our services, please follow the instructions below
carefully.
Technical Support
We want you to get the best performance possible from your products. If you run into
technical difficulties, we are here to help. For the most frequently asked questions,
you can easily find answers in your product documentation. These answers are nor-
mally a lot more detailed than the ones we can give over the phone.
Please consult this manual first. If you still cannot find the answer, gather all the infor-
mation or questions that apply to your problem, and with the p can be assured that
your product will provide the reliability and ease of operation forfloor, you can
be assured that your product will provide the reliability and ease of o oy orod-
uct close at hand, call your dealer. Our dealers are well trained and ready to give you
the support you need to get the most from your Advantech products. In fact, most
problems reported are minor and can be easily solved over the phone.
In addition, free technical support is available from Advantech engineers every busi-
ness day. We are always ready to give advice about application requirements or spe-
cific information on the installation and operation of any of our products.
Initial Inspection
Before setting up the system, check that the items listed below are included and in
good condition. If any item does not accord with the table, please contact your dealer
immediately.
1 x ITA-3630 series industrial computer
1 x ITA-3630 accessory box
1 x Warranty card
If any of these items are missing or damaged, contact your distributor or sales repre-
sentative immediately. We have carefully inspected the ITA-2000/ITA-2000R
mechanically and electrically before shipment. It should be free of marks and
scratches and in perfect working order upon receipt. As you unpack the ITA-2000/
ITA-2000R, check it for signs of shipping damage. (For examples: box damage,
scratches, dents, etc.) If it is damaged or it fails to meet the specifications, notify our
service department or your local sales representative immediately. Also, please notify
the carrier. Retain the shipping carton and packing material for inspection by the car-
rier. After inspection, we will make arrangements to repair or replace the unit.

v ITA-3630 User Manual
Safety Instructions
1. Read these safety instructions carefully.
2. Keep this User Manual for later reference.
3. For plug-in equipment, the power outlet socket must be located near the equip-
ment and must be easily accessible.
4. Keep this equipment away from humidity.
5. Put this equipment on a reliable surface during installation. Dropping it or letting
it fall may cause damage.
6. The openings on the enclosure are for air convection. Protect the equipment
from overheating. DO NOT COVER THE OPENINGS.
7. Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.
8. Position the power cord so that people cannot step on it. Do not place anything
over the power cord.
9. All cautions and warnings on the equipment should be noted.
10. If the equipment is not used for a long time, disconnect it from the power source
to avoid damage by transient overvoltage.
11. Never pour any liquid into an opening. This may cause fire or electrical shock.
12. Never open the equipment. For safety reasons, the equipment should be
opened only by qualified service personnel.
13. If one of the following situations arises, get the equipment checked by service
personnel:
The power cord or plug is damaged.
Liquid has penetrated into the equipment.
The equipment has been exposed to moisture.
The equipment does not work well, or you cannot get it to work according to
the user's manual.
The equipment has been dropped and damaged.
The equipment has obvious signs of breakage.
14. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE
STORAGE TEMPERATURE MAY GO BELOW -20° C (-4° F) OR ABOVE 60° C
(140° F). THIS COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT
SHOULD BE IN A CONTROLLED ENVIRONMENT.
15. CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY
REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE
RECOMMENDED BY THE MANUFACTURER, DISCARD USED BATTERIES
ACCORDING TO THE MANUFACTURER'S INSTRUCTIONS.
The sound pressure level at the operator's position according to IEC 704-1:1982 is
no more than 70 dB (A).
DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech
disclaims all responsibility for the accuracy of any statements contained herein.

ITA-3630 User Manual vi
Safety Precaution - Static Electricity
Follow these simple precautions to protect yourself from harm and the products from
damage.
To avoid electrical shock, always disconnect the power from your PC chassis
before you work on it. Don't touch any components on the CPU card or other
cards while the PC is on.
Disconnect power before making any configuration changes. The sudden rush
of power as you connect a jumper or install a card may damage sensitive elec-
tronic components.
Battery Information
Batteries, battery packs and accumulators should not be disposed of as unsorted
household waste. Please use the public collection system to return, recycle, or treat
them in compliance with the local regulations.

vii ITA-3630 User Manual
Contents
Chapter 1 Overview...............................................1
1.1 Introduction ............................................................................................... 2
1.2 Specifications ............................................................................................ 2
1.3 Power Information ..................................................................................... 2
Table 1.1: Power ......................................................................... 2
1.4 Environmental Specifications .................................................................... 3
Table 1.2: Environmental Specifications ..................................... 3
1.5 Dimension Diagram................................................................................... 3
Figure 1.1 Dimension Diagram of ITA-3630 ................................ 3
Figure 1.2 Exploded Diagram of ITA-3630 .................................. 4
Table 1.3: Part List ...................................................................... 4
Chapter 2 H/W Installation....................................5
2.1 Introduction ............................................................................................... 6
2.2 Jumpers and Connectors .......................................................................... 6
2.2.1 Jumper Description ....................................................................... 6
2.2.2 Jumper and Connector Location................................................... 7
Figure 2.1 Jumper and Connector Location on Main Board ........ 7
Table 2.1: Jumpers...................................................................... 7
Table 2.2: JLVDS1: LVDS Voltage Selection .............................. 8
Table 2.3: JCOMS1: CMOS Clear Function................................ 8
Table 2.4: PSON1: Startup-up Mode Selection........................... 8
Table 2.5: VCCGPIO1: GPIO Voltage Selection ......................... 8
2.3 I/O Connectors .......................................................................................... 9
Figure 2.2 ITA-3630-S0A1E Rear I/O Interfaces ......................... 9
Figure 2.3 ITA-3630 Front I/O Interfaces..................................... 9
2.3.1 COM Connector .......................................................................... 10
Table 2.6: COM Connector Pin Definition ................................. 10
2.3.2 HDMI Connector ......................................................................... 10
Table 2.7: HDMI Connector Pin Definition................................. 10
2.3.3 VGA Connector........................................................................... 11
Table 2.8: VGA Connector Pin Definition .................................. 11
2.3.4 USB 2.0 Connector ..................................................................... 11
Table 2.9: USB2.0 Connector Pin Definition ............................. 11
2.3.5 USB 3.0 Connector ..................................................................... 12
Table 2.10: USB3.0 Connector Pin Definition ............................. 12
2.3.6 DIO Connector ............................................................................ 12
Table 2.11: DIO Connector Pin Definition ................................... 12
2.3.7 Audio in Connector ..................................................................... 12
2.3.8 PS/2 Connector........................................................................... 13
Table 2.12:PS/2 Connector Pin Definition ................................. 13
2.3.9 LAN Connector ........................................................................... 13
Table 2.13: Ethernet Connector Pin Definition ........................... 13
Table 2.14:LED Color Definition ................................................. 13
2.3.10 Phoenix Terminal Connector ...................................................... 14
Table 2.15: Power Connector Pin Definition................................ 14
2.3.11 LPT Connector............................................................................ 14
Table 2.16:LPT Connector Pin Definition ................................... 14
2.3.12 LVDS Connector ......................................................................... 15
Table 2.17: LVDS Connector Pin Definition ................................ 15
2.3.13 LED Indicators for System Status ............................................... 15

ITA-3630 User Manual viii
Chapter 3 System Setup .................................... 17
3.1 Introduction ............................................................................................. 18
3.1.1 Installing Mainboard mini-PCIe card and mini SATA.................. 18
Figure 3.1 Installing Mainboard mini-PCIe card and mini SATA 18
3.1.2 Installing USB Dongle................................................................. 19
Figure 3.2 Installing USB Dongle .............................................. 19
3.1.3 Installing HDD Module ................................................................ 20
Figure 3.3 Installing HDD Module.............................................. 20
Figure 3.4 Installing HDD+CF Module....................................... 21
3.1.4 Installing Foot Stand ................................................................... 21
Figure 3.5 Installing Foot Stand................................................. 21
3.1.5 Installation Notes ........................................................................ 22
Figure 3.6 Desktop Mount ......................................................... 22
Figure 3.7 Wall Mount ............................................................... 22
Chapter 4 BIOS Setting ...................................... 23
4.1 Introduction ............................................................................................. 24
Figure 4.1: Setup Program Initial Screen ................................... 24
4.2 Entering Setup ........................................................................................ 24
Figure 4.2: POST Screen ........................................................... 24
4.2.1 Main Setup.................................................................................. 25
Figure 4.3: Main Setup Screen................................................... 25
4.2.2 Advanced BIOS Features Setup................................................. 26
Figure 4.4: Advanced BIOS Features Setup Screen.................. 26
Figure 4.5 ACPI Configuration................................................... 26
Figure 4.6: CPU Configuration (1) .............................................. 27
Figure 4.7 CPU Configuration (2) .............................................. 27
Figure 4.8 SATA Configuration.................................................. 28
Figure 4.9: USB Configuration.................................................... 29
Figure 4.10:Super I/O Configuration........................................... 30
Figure 4.11Serial Port Configuration .......................................... 30
Figure 4.12:H/W Monitor COnfiguration ..................................... 31
Figure 4.13:CPU PPM Configuration.......................................... 32
Figure 4.14:APM Configuration .................................................. 33
4.2.3 Advanced Chipset Features Setup ............................................. 33
Figure 4.15Advanced Chipset Features Setup........................... 33
Figure 4.16PCH-IO Configuration .............................................. 34
Figure 4.17Chipset USB Configuration ...................................... 34
Figure 4.18PCH Azalia Configuration......................................... 35
Figure 4.19:System Agent (SA) Configuration............................ 36
Figure 4.20Graphics Configuration Menu................................... 36
Figure 4.21LCD Control.............................................................. 37
4.2.4 Boot Setup .................................................................................. 38
Figure 4.22:Boot Setup............................................................... 38
Figure 4.23Boot Option Priorities ............................................... 39
Figure 4.24:CSM Parameter....................................................... 39
4.2.5 Security Setup ............................................................................ 40
Figure 4.25:Setup Security Menu ............................................... 40
4.2.6 Save & Exit Setup....................................................................... 41
Figure 4.26:Setup Save & Exit Menu.......................................... 41
Chapter 5 Driver Installation.............................. 43
5.1 Introduction ............................................................................................. 44
5.2 Driver Installation .................................................................................... 44
5.2.1 Chipset Windows Driver Setup ................................................... 45

ix ITA-3630 User Manual
5.2.2 VGA Windows Driver Setup........................................................ 45
5.2.3 ME Windows Driver Setup .......................................................... 46
5.2.4 LAN Windows Driver Setup ........................................................ 46
5.2.5 USB 3.0 Windows Driver Setup .................................................. 47
5.2.6 Audio Windows Driver Installation .............................................. 47
Chapter 6 GPIO Programming Guide ................49
6.1 ITA-3630 Digital DIO Definition ............................................................... 50
6.2 Configuration Sequence.......................................................................... 50
6.3 Function Call for Reference .................................................................... 54
Appendix A Programming the Watchdog Timer..59
A.1 Programming the Watchdog Timer ......................................................... 60
A.1.1 Watchdog Timer Overview.......................................................... 60
A.1.2 Programming the Watchdog Timer ............................................. 60
Table A.1: Watchdog Timer Registers ....................................... 60
A.1.3 Example Program ....................................................................... 61

ITA-3630 User Manual x

Chapter 1
1Overview
Sections include:
Introduction
Specifications
Power Information
Environment Specifications
Dimension Diagram

ITA-3630 User Manual 2
1.1 Introduction
The ITA-3630 is a fan-less, compact embedded industrial computer chassis with
CoreTM i7/i5/i3 dual core processor and wide voltage input range, which is specially
designed for intelligent transportation - Road Surveillance. This powerful computing
platform can stand operation 24 hours a day, 7 days a week.
1.2 Specifications
Processor and Chipset: CoreTM i7/i5/i3 processor + Intel® HM76 chipset
BIOS: AMI SPI 64 Mb Flash
Memory: On-board 4 GB DDR3 1333/1600 MHz
Display: Integrated graphics HD4000, with up to 256 MB SDRAM shared sys-
tem memory
Dual Display:
–Single display resolution up to 2048 x 1536 @ 60 Hz
–Dual Display resolution up to 1920 x 1200 @ 60 Hz
Storage: Supports 2 x 2.5” HDD slot or 1 x CF slot and 1 x 2.5” HDD slot
Expansion Slot: Supports 1 x Mini PCIe slot
Ethernet: 2 x 10/100/1000M Ethernet (Controller chip: Intel i210-AT)
USB: 4 x USB2.0 and 2 x USB 3.0
VGA: 1 x VGA
HDMI:1 x HDMI
LVDS: 1 x LVDS (Reserved pin header on main board)
Serial I/O: 2 x DB9, RS232/422/485 with automatic flow control
Digital I/O: 1 x 8-ch GPIO
Audio: 1 x Speaker out with 2 x 4 w amplifer; 1 Mic input
Reserved Zone:
–1 x LPT
–1 x LVDS
–2 x VGA (Optional PCA-5650 graphic card expansion for 2 VGA)
Dimensions (W x H x D):
–213 x 82.7 x 240 mm (without ears)
–253 x 86.6 x 240 mm (with ears)
Weight: 3.75 kg
1.3 Power Information
ITA-3630 supports DC 9 ~ 36 V wide voltage input
Table 1.1: Power
DC voltage input 9 V - 36 V
DC current 7.2 A - 1.8 A
DC power interface 2-pin terminal block

3 ITA-3630 User Manual
Chapter 1 Overview
1.4 Environmental Specifications
1.5 Dimension Diagram
Figure 1.1 Dimension Diagram of ITA-3630
Table 1.2: Environmental Specifications
Operating Temperature With industrial HDD: 0 ~ 40°C
With CF card: -25 ~ 60 °C (With 0.7 m/s airflow)
SAfety Certificate
Temperature -10 ~ 50°C (With industrial standard SSD/CF/mSATA)
Storage Temperature -40 ~ 85°C
Humidity 95% @ 40º C, non-condensing
Vibration
With Compact Flash: 2 Grms @ 5 ~ 500 Hz, random, 1 hr/axis
With 2.5” HDD: 1 Grms @ 5 ~ 500 Hz, random, 1 hr/axis
IEC60068-2-6 Sine 2G @ 5 ~ 500Hz, 1hr/axis
Shock
With Compact Flash: 20G, IEC-68-2-27, half-sine wave, 11 ms
duration
With 2.5” HDD: 10G, IEC-68-2-27, half-sine wave, 11 ms duration
Safety UL, CCC, BSMI, CE and FCC compliant

ITA-3630 User Manual 4
Figure 1.2 Exploded Diagram of ITA-3630
Table 1.3: Part List
1 Heat sink 9 USB tray
2 Chassis foot stand 10 HDD Tray
3 Chassis 11 2.5” HDD fix bracket
4 Front panel 12 HDD buffer rubber
5 Blank bracket 13 Thermal pad
6 Blank bracket (CF) 14 Top cover
7 USB bracket 15 Rubber foot pad
8 Main board

Chapter 2
2H/W Installation
Sections include:
Introduction
Jumpers and Connectors
I/O Connectors

ITA-3630 User Manual 6
2.1 Introduction
The following sections show the internal jumpers setting and the external connectors
pin assignment for application integration.
2.2 Jumpers and Connectors
2.2.1 Jumper Description
You may configure the ITA-3630 to match the needs of your application by setting
jumpers. A jumper is a metal bridge used to close an electric circuit. It consists of two
metal pins and a small metal clip (often protected by a plastic cover) that slides over
the pins to connect them. To close a jumper, you remove the clip. Sometime a jumper
will have three pins, labelled 1, 2 and 3. In this case you would connect either pins 1
and 2, or 2 and 3.
The jumpers setting are schematically depicted in this manual as follows.
A pair of needle-nose pliers may be helpful when working with jumpers. If you have
any doubts about the best hardware configuration for your application, contact your
local distributor or sales representative before you make any changes. Generally, you
simply need a standard cable to make most connections.
Open Closed 2-3 Closed
断开 闭合 闭合 2-3
Open Closed 2-3 Closed

7 ITA-3630 User Manual
Chapter 2 H/W Installation
2.2.2 Jumper and Connector Location
The board has a number of connectors and jumpers that allow you to configure your
system to suit your application. The table below lists the function of each of the con-
nectors and jumpers.The locations of jumpers and connector on the board are shown
in Figure 2.1.
Figure 2.1 Jumper and Connector Location on Main Board
Table 2.1: Jumpers
Label Function
JLVDS1 LVDS voltage selection
JCOMS1 Clear CMOS settings
PSON1 Start-up mode selection
VCCGPIO1 GPIO voltage selection

ITA-3630 User Manual 8
Table 2.2: JLVDS1: LVDS Voltage Selection
Closed Pins Setting
3-4 +V12
2-4 +V5
4-6 Normal (+V3.3)*
*Default setting
Table 2.3: JCOMS1: CMOS Clear Function
Closed Pins Setting
1-2 Default*
2-3 Clear CMOS
* Default setting
Table 2.4: PSON1: Startup-up Mode Selection
Closed Pins Setting
1-2 AT Mode
2-3 ATX Mode*
* Default setting
Table 2.5: VCCGPIO1: GPIO Voltage Selection
Closed Pins Setting
1-3 +V5_SB
2-4 Normal (+V3_SB)*
3-5 +V5
4-6 +V3.3
* Default setting
+V5 +V3.3

9 ITA-3630 User Manual
Chapter 2 H/W Installation
2.3 I/O Connectors
Figure 2.2 ITA-3630-S0A1E Rear I/O Interfaces
Figure 2.3 ITA-3630 Front I/O Interfaces
AudioPS/2
USB2.0 x 4
COM x 2
HDMI
DC Input
DIO
LAN x 2
VGA Power ButtonUSB3.0 x 2
Reserved I/O connector for LPT/LVDS/COM via a cable
2 x USB2.0 connector bracket Easy-plug CF/DOM module

ITA-3630 User Manual 10
2.3.1 COM Connector
ITA-3630 provides two D-sub 9-pin connectors for RS-232/422/485. The default set-
ting is RS-232.
2.3.2 HDMI Connector
Table 2.6: COM Connector Pin Definition
RS-232 RS-422 RS-485
Pin Signal Name Signal Name Signal Name
1DCD Tx- DATA-
2RxD Tx+ DATA+
3TxD Rx+ NC
4DTR Rx- NC
5GND GND GND
6 DSR NC NC
7 RTS NC NC
8 CTS NC NC
9RI NC NC
Table 2.7: HDMI Connector Pin Definition
Pin Signal Name Signal Name Signal Name
1 TMDS Data2+ 11 TMDS Clock Shiled
2 TMDS Data2 Shiled 12 TMDS Clock-
3 TMDS Data2- 13 CEC
4 TMDS Data1+ 14 Reserved
5 TMDS Data1 Shiled 15 SCL
6 TMDS Data1- 16 SDA
7 TMDS Data0+ 17 DDC/CEC Ground
8 TMDS Data0 Shiled 18 +5V Power
9 TMDS Data0- 19 Hot Plug Detect
10 TMDS Clock+