Advantech TREK-688 User manual

User Manual 




TREK-688





Computer

TREK-688 User Manual 2
Copyright

The documentation and the software included with this product are copyrighted 2015
by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right
to make improvements in the products described in this manual at any time without
notice. No part of this manual may be reproduced, copied, translated or transmitted
in any form or by any means without the prior written permission of Advantech Co.,
Ltd. Information provided in this manual is intended to be accurate and reliable. How-
ever, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringe-
ments of the rights of third parties, which may result from its use.


Acknowledgements

Intel® and Pentium are trademarks of Intel Corporation.
Microsoft Windows® and MS-DOS are registered trademarks of Microsoft Corp.
All other product names or trademarks are properties of their respective owners.

Product Warranty (2 years)

Advantech warrants to you, the original purchaser, that each of its products will be
free from defects in materials and workmanship for two years from the date of pur-
chase.
This warranty does not apply to any products which have been repaired or altered by
persons other than repair personnel authorized by Advantech, or which have been
subject to misuse, abuse, accident or improper installation. Advantech assumes no
liability under the terms of this warranty as a consequence of such events.
Because of Advantech’s high quality-control standards and rigorous testing, most of
our customers never need to use our repair service. If an Advantech product is defec-
tive, it will be repaired or replaced at no charge during the warranty period. For out-
of-warranty repairs, you will be billed according to the cost of replacement materials,
service time and freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For example, CPU
speed, Advantech products used, other hardware and software used, etc.) Note
anything abnormal and list any onscreen messages you get when the problem
occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return merchandize
authorization) number from your dealer. This allows us to process your return
more quickly.
4. Carefully pack the defective product, a
fully-completed Repair and Replacement
Order Card and a photocopy proof of purchase date (such as your sales receipt)
in a shippable container. A product returned without proof of the purchase date
is not eligible for warranty service.
5. Write the RMA number visibly on the outside of the package and ship it prepaid
to your dealer.





Part No. 2008T68800 Edition 1
Printed in Taiwan November 2015

3 TREK-688 User Manual
Declaration of Conformity


CE

This product has passed the CE test for environmental specifications. Test conditions
for passing included the equipment being operated within an industrial enclosure. In
order to protect the product from being damaged by ESD (Electrostatic Discharge)
and EMI leakage, we strongly recommend the use of CE-compliant industrial enclo-
sure products.


FCC Class B

Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installa-
tion. This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful inter-
ference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interfer-
ence to radio or television reception, which can be determined by turning the equip-
ment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
ʳʳʳʳʳʳʳʳʳ Reorient or relocate the receiving antenna (cable over 20 CM)
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

 FCC Caution :
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
 FCC RF Radiation Exposure Statement :
1. This Transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
2. This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 20
centimeters between the radiator and your body.
According to FCC 15.407(e), the device is intended to operate in the frequency band
of 5.15GHz to 5.25GHz under all conditions of normal operation. Normal operation of
this device is restricted to indoor used only to reduce any potential for harmful
interference to co-channel MSS operations.

Technical Support and Assistance

1. Visit the Advantech web site at http://support.advantech.com where you can find
the latest information about the product.
2. Contact your distributor, sales representative, or Advantech's customer service
center for technical support if you need additional assistance. Please have the
following information ready before you call:
– Product name and serial number
– Description of your peripheral attachments
– Description of your software (operating system, version, application software,

TREK-688 User Manual 4
etc.)
– A complete description of the problem
– The exact wording of any error messages



 


5 TREK-688 User Manual
Warnings, Cautions and Notes
Warning! Warnings indicate conditions, which if not observed, can cause personal
injury!
Caution! Cautions are included to help you avoid damaging hardware or losing
data. e.g.
There is a danger of a new battery exploding if it is incorrectly installed.
Do not attempt to recharge, force open, or heat the battery. Replace the
battery only with the same or equivalent type recommended by the man-
ufacturer. Discard used batteries according to the manufacturer's
instructions.
Note! Notes provide optional additional information.
Document Feedback
To assist us in making improvements to this manual, we would welcome comments
and constructive criticism. Please send all such - in writing to: support@advan-
tech.com
Packing List
Before setting up the system, check that the items listed below are included and in
good condition. If any item does not accord with the table, please contact your dealer
immediately.
Partnumber Description Q`ty
 TREK688ComputingBox 1
175000792701 2in1(WWAN+GPS)Antenna 1
175000792801 WWANAntenna 1
175000756401 WiFi+BT(2.4/5GHz)Antenna 1
170002305101 VIOCable 1
170002305001 GIOCable 1
170002270201 VideoCable 2
1700019031 Powercable(2M) 1
1700020123 USBCable 1
9680001742 HDD/SSDTraykeylock 1

TREK-688 User Manual 6


Ordering Information



P/N Description

TREK6887LWB7PA0E i74650U/LTE/HSPA+(EU)/GPS/WLAN/BT/SSD/Win7Pro
TREK6887LWB7PB0E i74650U/LTE/HSPA+(US)/GPS/WLAN/BT/SSD/Win7Pro


Safety Instructions

1. Read these safety instructions carefully.
2. Keep this User Manual for later reference.
3. Disconnect this equipment from any AC outlet before cleaning. Use a damp
cloth. Do not use liquid or spray detergents for cleaning.
4. For plug-in equipment, the power outlet socket must be located near the equip-
ment and must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or
letting
it
fall may cause damage.
7. Do not leave this equipment in an environment unconditioned where the storage
temperature under -40° C (-40° F) or above 80° C (176° F), it may damage the
equipment. Operating temperature: -30° C ~55° C.
8. The openings on the enclosure are for air convection. Protect the equipment
from overheating. DO NOT COVER THE OPENINGS.
9. Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.
10. Position the power cord so that people cannot step on it. Do not place anything
over the power cord. The voltage and current rating of the cord should be greater
than the voltage and current rating marked on the product.
11. All cautions and warnings on the equipment should be noted.
12. If the equipment is not used for a long time, disconnect it from the power source
to avoid damage by transient overvoltage.
13. Never pour any liquid into an opening. This may cause fire or electrical shock.
14. Never open the equipment. For safety reasons, the equipment should be
opened only by qualified service personnel.
15. If one of the following situations arises, get the equipment checked by service
personnel:
ʳ The power cord or plug is damaged.
ʳ Liquid has penetrated into the equipment.
ʳ The equipment has been exposed to moisture.
ʳ The equipment does not work well, or you cannot get it to work according to
the user's manual.
ʳ The equipment has been dropped and damaged.
ʳ The equipment has obvious signs of breakage.
16. CAUTION: The computer is provided with a battery-powered real-time clock cir-
cuit. There is a danger of explosion if battery is incorrectly replaced. Replace

TREK-688 User Manual 6
only with same or equivalent type recommended by the manufacture. Discard
used batteries according to the manufacturers instructions.
17. THE COMPUTER IS PROVIDED WITH CD DRIVES COMPLY WITH APPRO-
PRIATE SAFETY STANDARDS INCLUDING IEC 60825.
18. This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
19. CAUTION: Always completely disconnect the power cord from your chassis
whenever you work with the hardware. Do not make connections while the
power is on. Sensitive electronic components can be damaged by sudden
power surges.
20. CAUTION: Always ground yourself to remove any static charge before touching
the motherboard, backplane, or add-on cards. Modern electronic devices are
very sensitive to static electric charges. As a safety precaution, use a grounding
wrist strap at all times. Place all electronic components on a static-dissipative
surface or in a static-shielded bag when they are not in the chassis.
21. CAUTION: Any unverified component could cause unexpected damage. To
ensure the correct installation, please always use the components (ex. screws)
provided with the accessory box.
22. Caution text concerning lithium batteries:
23. "Rack Mount Instructions - The following or similar rack-mount instructions are
included with the installation instructions:
A) Elevated Operating Ambient - If installed in a closed or multi-unit rack
assembly, the operating ambient temperature of the rack environment may
be greater than room ambient. Therefore, consideration should be given to
installing the equipment in an environment compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
B) Reduced Air Flow - Installation of the equipment in a rack should be such that
the amount of air flow required for safe operation of the equipment is not
compromised.
C) Mechanical Loading - Mounting of the equipment in the rack should be such
that a hazardous condition is not achieved due to uneven mechanical load-
ing.
D) Circuit Overloading - Consideration should be given to the connection of the
equipment to the supply circuit and the effect that overloading of the circuits
might have on over current protection and supply wiring. Appropriate consid-



eration of equipment nameplate ratings should be used when addressing this
concern.
E) Reliable Earthing - Reliable earthing of rack-mounted equipment should be
maintained. Particular attention should be given to supply connections other than
direct connections to the branch circuit (e.g. use of power strips)."
24. CAUTION :
To avoid any possible accident, please following instructions to operate this unit.
25. CAUTION :
Only the qualified engineer by Advantech Co.,Ltd can perform the installation in
a vehicle. Improper installation can injure the operator or damage the vehicle
and/or TREK-688 computer system.
Follow the installation as below to avoid overloading the circuit after adding this
device.
Follow the instructions below to properly install the TREK-688 computing system
in a vehicle.
zDetermine the best location for mounting the unit taking into consideration
the driver`s field of view and ease of accessing the unit. (Only install this
unit in the car passenger compartment. Suggested locations are next to
driver`s seat or located on center console.)
zConnect the vehicle computer to the vehicle`s wiring system as below.
Routing Electrical Cables
Establish a near route for the cable, staying clear of moving parts or
hot surfaces whenever possible.
Fix the cable to existing cable runs inside the vehicle using cable ties,
but make sure they are away from any moving or hot surfaces.
When the cabling must go through a panel, use a suitable cable gland.
Ensure the cable does not have tight bends. The minimum
recommended radius is 2.5”.
Ensure cables do not swing or chafe on the structure.
DO NOT wind a cable in and out of the mesh on a cage.
Ensure that all fuses installed as instruction. 32 Volt is suitable for unit.
All power wiring must use the supplied power cable comply with
intended applications of SAE with suitable ratings of electrical,
temperature, exposure and flammability.
Fuses : UL LISTED Fuse for Automobile use.
- A 10 amp.
Keep the path between the battery and the vehicle computer as short
as possible and away from any part of the ignition high tension system.
A 10 amp. If your car exhibits electrical problems, the fuse may blow and
shut the system down to protect it from damage. Once the problem is
rectified, replace the blown fuse and the system should again be operational.

TREK-688 User Manual 8


Connecting the Power Cable
1. Disconnect the vehicle battery.
2. Connect the green wire to the vehicle`s negative power source.
NOTE see the vehicle Owner`s Manual for specific wiring information.
3. Connect the red wire of Fuse Box in passenger compartment to
vehicle`s positive power source. Connect the black wire to the
vehicle`s negative power source. Then Fuse Box secured to connector.
Insert the female connector of Fuse Box to the male connector of
TREK-688 vehicle system. Connect the Orange wire to the vehicle`s
ignition switch.
4. Ensure the wiring connections created are sufficiently insulated from
each other.
5. Re-connect the vehicle battery.
6. Insert the power cable connector into TREK-688 computing system
power port. Align the keyway on the power connector with the notch on
the vehicle computer`s power port.
CAUTION
Do not open the cover on the front side as illustration as below before
turning off the power.


Safety Precaution - Static Electricity

Follow these simple precautions to protect yourself from harm and the products from
damage.
 ʳTo avoid electrical shock, always disconnect the power from your PC chassis
before you work on it. Don't touch any components on the CPU card or other
cards while the PC is on.
 ʳDisconnect power before making any configuration changes. The sudden rush
of power as you connect a jumper or install a card may damage sensitive elec-
tronic components.
This product is intended to be supplied by a Listed DC power source, rated
9~32Vdc, 7A minimum and Tma 55 degree C, if need further assistance with
purchasing the DC power source, please contact Advantech for further information.

Warning! 1. Input voltage rated: 9 ~ 32 Vdc.



2. Transport: carry the unit with both hands and handle with care.
3. Maintenance: to properly maintain and clean the surfaces, use only
approved products or clean with a dry applicator.
4. CFast: Turn off the power before inserting or removing
CFast storage cards.






























































TREK-688 User Manual 1


Contents


Chapter 1General Information ............................1
1.1 Introduction
............................................................................................... 2
1.2 General
Specifications .............................................................................. 3
1.3 Dimensions
............................................................................................... 5
Figure 1.1 TREK-688
dimensions................................................ 5

Chapter

2

System Setup .......................................7
2.1






2.2
A Quick Tour of the TREK-688 Computing
Box ........................................ 8
Figure 2.1 Front view of
TREK-688 ............................................. 8
Figure 2.2 Rear view of
TREK-688 .............................................. 8
2.1.1 Installing CFast & SIM card…
........................................................... 9
2.1.2 Installing Storage……………………………………………………10
Installation Procedures








2.3
2.2.1 Connecting the Power
Cord .......................................................... 9
Table 2.1: Pin Definition of Power Cord
...................................... 9
2.2.2 Power
Connector .......................................................................... 9
Figure 2.6 Power connector
outlook ............................................ 9
Table 2.2: Pin
Definition of Power Connector (Molex Manufacturer
Part
no.0430451200) ................................................ 10
Figure 2.7 Power connector photo
............................................ 10
Running the BIOS Setup
Program .......................................................... 10


Chapter

3

Switches setting and I/O Connectors………. ..13
3.1 Setting Switches…………………………………………
.................................... 13

3.1.1 Switches List……………………………............................................ 13










3.2
3.3
3..1.2 Switch Location……………….................................................................. 1
3
3.1.3 Switch Setting……………………………………………………........... 13
3.1.3.1 MiniPCIe (WWAN) Power Voltage Setup (SW2)…………………13
3.1.3.2 MiniPCIe(WWAN) Support WWAN Module Setup (SW3)………13
3.1.3.3 CAN BUS Termination(Only for test use)(SW6)…………………14
3.1.3.4 MiniPCIe(WWAN) Power Voltage Setup (SW8)…………………14
3.1.3.5 MiniPCIe(WWAN) Support WWAN Module Setup(SW9)……….14
3.1.3.6 I/O DB9 PIN9 Select (ON TOP LAYOUT)(CN15)………………..14
LED Indicator………………………………………………………………….14
I/O Connectors Pin Assignment……………………………………..……..15
3.3.1 Power Connector………………………………………………………15
3.3.2 HDMI Connector………………………………………………………..15
3.3.3 Smart Display Connector……………………………………………..16
3.3.4 USB Connector (Rear side)…………………………………………..17
3.3.5 USB Connector (Front side)………………………………………….18
3.3.6 VGA & RS-232 Connector……………………………………………19
3.3.7 Video Input Connector………………………………………………..20
3.3.8 Vehicle I/O Connector…………………………………………………21
3.3.9 Generic I/O Connector………………………………………………..22
3.3.10 LAN Connector……………………………………………………….23



Chapter 4Software Demo Utility Setup............... 29
4.1 Introduction………………………………………………………………………30
4.2 IVCP Demonstration…………………………………………………………….30
4.2.1 Information…………………………………………………………………30

4.2.2 Mode Control………………………………………………………………31
4.2.3 Low voltage Protection……………………………………………………32

4.2.4 Event Delay………………………………………………………………...33
4.2.5 Alarm………………………………………………………………………..34

4.2.6 Watchdog…………………………………………………………………..35
4.2.7 G-Sensor…………………………………………………………………..36
4.2.8 Peripheral………………………………………………………………….37
4.2.9 Storage……………………………………………………………………..38
4.2.10 Digital IO………………………………………………………………….39
4.2.11 P-sensor………………………………………………………………….40
4.3 VCIL Demonstration…………………………………………………………….41
4.3.1 Port selection………………………………………………………….….41
4.3.2 Information…………………………………………………………….….42
4.3.3 Option…………………………………………………………………..….43
4.3.4 CAN/J1939/OBD2/J1708/J1587………………………………………..44
4.4 Smart Display Demonstration……………………………………………….…45
4.4.1 Information…………………………………………………………….….46
4.4.2 Backlight………………………………………………………………..….47
4.4.3 Hot Key………………………………………………………………….…48
4.4.4 Peripheral……………………………………………………………….…49
4.5 GPS Demonstration………………………………………………………….….50
4.5.1 Port selection……………………………………………………………...50
4.5.2 Information…………………………………………………………………51
4.5.3 NEMA………………………………………………………………………52
Appendix ATREK-303…………………………………53
A.1 TREK-303 Specification………………………………………………….……..54
Table A.1 TREK-303 Specification…………………………………….54
Table A.2 Smart Display Connector……………………………………55

Figure A.1 Hotkey utility…………………………………………………..56

TREK-688 User Manual 1



Chapter 1

1 General Information

This chapter gives background
information on the TREK-688
Premium In- Vehicle Computing Box.
Sections include:
ʳ Introduction
ʳ General Specifications
ʳ Dimensions

TREK688UserManual
1.1 Introduction
TREK-688 is an industrial-grade, powered by Intel® Haswell 4th generation dual core CPU
computing box designed to provide high quality video surveillance and fleet management
for eBus and BRT( Bus Rapid Transit). It can work in extreme environments with features
like the wide working temperature range (-30-55ɗ) and anti-shock/vibration to pass MIL-
STD-810G and 5M3 standard. Its special power protection surges from impacting the
system. Guarding against damage from transient car power.
TREK-688 combined with variety of I/O connectors can be connected to devices like
TPMS (Tire Pressure Monitoring System), Rear view Camera ( for parking monitoring)
and CAN Bus devices. It has dual CAN BUS ports and support several kind of vehicle
protocols (e.g. J1939,OBD-II) for vehicle diagnostics and driver behavior management.
Build-in wireless communication (WWAN, WLAN,BT) enable TREK-688 to send import
ant driver/vehicle/location/cargo information back to the control center. Furthermore,
TREK-688 also reserved three displays/dual audio interfaces supporting different
resolutions can deliver different applications to different displays; eg:one application to a
fleet driver and another to passenger to IVI and digital signage application.
TREK-688 I/O Overview

TREK-688 User Manual 4
Chapte
r
1 General Information
1.2 General Specifications
Features
Intel®HaswellCore™i7Dualcorehighperformanceprocessorformultitasking.
Embeddedvideoencodersupportsupto12analogvideoinputsforD1,30fpsresolutionand8audioinputs
DualexternalHDD/SSDtraywithkeylockprotection.
EasilypairedwithTREKinvehiclesmartdisplaysviaasinglecableconnection.
Intelligentvehiclepowermanagementsystemforignitionon/off/delayandpowerprotectionfunctions.
VehiclediagnosticinterfacewithconfigurabledualCAN(J1939,OBDII/ISO15765)andJ1708protocols.
BuiltinLTE/GNSS/WLAN/BT(withdualSIMcards)modules.
AdvancedShock&antivibrationcertifiedbyMILSTD810G,EN607213(5M3)
Richmanagement&videoSDK,testutilityforcustomerevaluating.


Specifications
Processor Intel®Core™i74650UDualCore,2.9GHz(i34010U&i54300Uby
projectsupport)
Memory
1xSODIMMsocket
Upto8GBDDR3L1600NonECCmemorymodule;(Default
configuration:4GB)
Graphic IntelHDgraphics44001.1GHz
VideoHWEncoder StretchS7,supportH.264,MJPEGformat;ResolutionuptoD1,30fps
perchannel
Core
O.S Windows7pro32bitasdefault.WES7,WE8S32bitbyprojectsupport
LinuxFedora18Remix(kernel3.8.0)(32bit)byprojectsupport
CFast 1xexternalaccessibleCFastslotwithcover,supportsystembootup
Defaultconfiguration:16GB,SLCSQFlashCFastcard
mSATA 1xmSATAslot,supportsystembootup
Defaultconfiguration:N/A;BOMoptional,byprojectbased
Storage
HDD/SSD
2xexternalaccessible2.5"MobileHDD/SSDtraywithkeylock
protection,supportsystembootup(Optional)
SupportSATAGen2(3Gb/s)
SmartDisplayPort(*1)
12V/2ApoweroutputforTREK30x
1x18bitsLVDS(Resolution:800x480(TREK303),1024x768(TREK
306);defaultTREK306)
1xLineOut(*2)(ForSpeakersonTREK30x)
2xUART(TX/RX,TX/RX/RTS)(ForT/S,Hotkeys,brightness,light
sensorcontrol)
1xUSB2.0TypeA
1xPWRButtonSignal
1xResetButtonSignal
HDMI 1xHDMI1.3b(Resolutionupto1920x1080)
Display
VGA 1xDB15(Resolutionupto2560x1600)
VehicleI/OPort 2xCANBus(SupportRawCAN,J1939,OBDII/ISO15765;FW
configurable)
1xJ1708(SupportJ1587)
1x4wireRS232/422/485(DefaultRS485,bysoftwaresetting)
GenericI/OPort 2x4wireRS232
4xIsolatedDI(DryContact)
4xIsolatedDO(Opencollectoroutput,drivingbyrelay)
1xLineOut(*2)
1xMicIn
StandardI/OPort 1xUSB2.0TypeA(Frontside)
2xUSB3.0TypeA(Rearside,withcableclip)
1xHighSpeedFullRS232,DB9(Pin9=Ring,12V/5V@0.5AisBOM
optionalbyjumpersetting)
2xGigaLAN,with8pinM12connector
I/O
Video/Audioinput 16chVideoinputs,VideoCompression:supportH.264,MJPEG

5 TREK-688 User Manual
(AV1&AV2,viadual
DVIIconnector)
format;ResolutionuptoD1,30fpsperchannel,total480fps.
8chmonoAudioinputs,AudioCompression:G.711
LED 6xLEDs(Power(Red),CFast(Yellow),WLAN(Green),WWAN(Green),
GPS(Yellow),Networkconnection(Yellow))
PowerButton ViaTREK30x(InVehicleSmartDisplay);Systemispoweredonby
Ignitionindefault

ResetButton 1xResetbutton(Frontside)
WLAN+Bluetooth IEEE802.11a/b/g/n+Bluetooth4.0combomoduleviaFullMiniPCIe
Slot
WWAN 4G(LTE,HSPA+,GSM/GPRS/EDGE,EVDOReva1,1xRTT):Sierra
WirelessMC73xxviaFullMiniPCIeSlot
(Default:MC7354forUS/MC7304forEU)
GNSS BuildinubloxMAXM8WGPS/Glonass/Beidoumodule,supportAGPS
RF
Antenna 4xSMAtypeantennaholeforGPS,WiFI+BT,WWAN/LTEMIMO.(*3)
Voltageinput Supports12/24Vcarpowersystem.(9V~32VwideDCinput,ISO
76372&SAEJ1113compliant.)
Power
IntelligentVehicle
Power
Management(iVPM2.0)
Systempoweron/off/hibernatemanagement(e.g.Programmable
IgnitionOn/OffTimedelay)
SupportWakeupEvents:
Alarm(RTC)Wakeup.
WakeupbyCall/SMS.
WakeupbyGsensor.
Systempowerprotection(e.g.CarBatteryLowVoltageProtection)
Systemmonitoringanddiagnostic
Dimensions(WxHxD) 346x92.5x196.2mm
Mechanical Weight 5.9kg(withtwoHDDs)
IPRating IP30
Vibration/Shock MILSTD810G,EN607213(5M3)
EMC CE,FCC
Safety UL/cUL,CB
VehicleRegulation EMark(E13),SAEJ1455classC,ISO76372,SAEJ1113,EN50155,IEC
60571
RFRegulation CE(R&TTE),FCCID
OperatingTemperature 30°C~55°C
Environment
StorageTemperature 40°C~80°C
*1:TobepairedwithTREK303/306directly.(Singlecableconnection)
*2:Supportdualindependentaudiostreams.(i.e.TheLineOutinterfacein"SmartDisplayPort"and
"GenericI/OPort"aredrivenbydifferentAudiocodecs.)
*3:TheconnectortypeonboxsideisFemaleRPSMAconnector.(i.e.Femaleconnectorbody(outside
threads)withamaleinnerpincontact.)

TREK-688 User Manual 6


Chapte
r
1 General Information
1.3 Dimensions

Figure 1.1 TREK-688 dimensions






























Chapter 2

2 System Setup

This chapter details system setup
on TREK-688
Sections include:

ʳ A Quick Tour of the Computer
Box

ʳ Installation Procedures

ʳ Running the BIOS Setup
Program

TREK-688 User Manual 8
2.1 A Quick Tour of the TREK-688 Computing Box
Before starting to set up the In-Vehicle Computing Box, take a moment to become
familiar with the locations and functions of the controls, drives, connectors and ports,
which are illustrated in the figures below.


Figure 2.1 Front view of TREK-688



Figure 2.2 Rear view of TREK-688












9 TREK-688 User Manual



2.1.1 Installing CFast Card & SIM card

 RemoveCFastdoorscrewandcaninstallCFastCard&SIMCarddirectly.PleaseinsertSIMCardfromSIM1
slotbecausedefaultpriorityisSIM1.IfyouinserttoSIM2slot,youhavetomodifysettingofSDK.





Figure 2.3 Installing CFast card & SIM card



2.1.2 Installing Storage
1. Release2pcsscrewsofeachHDD/SDDTrayandpulloutthetray.
2. Remove8pcsscrewsofHDD/SSDtraytopcoverandtakeouttheHDD/SSDframe.InsertHDD/SSDintothe
frameandfixby4pcsscrews.
3. FixHDD/SSDtraytopcoverby8pcsscrews.
SIM1 SIM2 CFastCard