Advantech DLoG DLT-V72 Series User manual

Quick Start Guide: DLT-V72 Industrial PC
Advantech-DLoG
Quick Start Guide: DLT-V72, V1.00, PN 20DLDOCX88521E00
Page 1 / 8
1 For your safety
Carefully read and comply with this
quick start guide.
Carefully read and comply with the
safety information provided with the
DLT-V72.
Keep all documents for future
reference.
DANGER
Observe the intended use.
Observe the intended use of the DLT-V72, e.g. no use in EX zone (potentially
explosive), no use in life-supporting systems or security-critical facilities.
For details, see User Manual DLT-V72 available in the Download
Center at www.advantech-dlog.com.
WARNING
Hazardous voltage, electric shock from contact with live parts.
This quick start guide is intended for skilled personnel.
Only authorized skilled personnel may put the DLT-V72 into operation.
For DLT-V72 industrial PCs with an uninterrupted power supply (UPS),
knowledge is required of lithium-ion batteries and the precautions that have to be
taken with them.
Do not put the DLT-V72 into operation if it is visibly damaged.
Do not open or modify the DLT-V72.
Operators of the DLT-V72 must be trained in the handling of the device.

Quick Start Guide: DLT-V72 Industrial PC
Advantech-DLoG
Quick Start Guide: DLT-V72, V1.00, PN 20DLDOCX88521E00
Page 2 / 8
2 Technical data DLT-V72
Dimensions and weight
DLT-V7210
Dimensions
Width x height x depth in mm: 297 x 238.5 x 67
Weight
3.7 kg (with screen defroster, without accessories)
DLT-V7212
Dimensions
Width x height x depth in mm: 335 x 267 x 69
Weight
4.65 kg (with PCT, without accessories)
Environmental conditions DLT-V72 without integrated UPS
Operating temperature
-30 to +50 °C
Storage temperature
-30 to +65 °C
Vibration/shock Class 5M3 according to EN 60721-3-5
US Highway Truck according to MIL-STD 810F
IP protection class
IP66
Environmental conditions DLT-V72 with integrated UPS
See chapter 8.
3 Operation DLT-V72
This key has two fuctions.
Function 1: Activate/deactivate touchscreen
Touch LED on (orange): Touchscreen inactive
Touch LED off: Touchscreen active
Function 2, in combination with the <SHIFT> key:
Activate/deactivate screen defroster (optional)
Note: The temp LED indicates whether the screen defroster is active
or inactive, not the touch LED above this key.
- Device on/off
- Display brighter
- Display darker
- Backlighting on/off
- Touchscreen or
Screen deforster
on/off
- S1 to S8
- SHIFT

Quick Start Guide: DLT-V72 Industrial PC
Advantech-DLoG
Quick Start Guide: DLT-V72, V1.00, PN 20DLDOCX88521E00
Page 3 / 8
4 Software configuration
4.1 DLoG Config for DLT-V72 with Microsoft Windows
The DLoG Config software is used to configure DLT-V72 devices with a Microsoft
Windows operating system. Aspects such as the following are configured:
−Automatic shutdown
−Wi-Fi status display
−Front-key assignment
−Network settings
−Battery pack charge settings (only on devices with optional UPS)
−Screen defroster heating function (only on devices with optional screen
defroster)
−Operation with gloves possible (only on devices with optional PCT touchscreen)
Start DLoG Config by choosing Start -> Programs -> DLoG: DLoG Config
or by clicking the Config icon on the taskbar.
DLoG Config default password: "gold".
DLoG Config is automatically started in admin mode. Only in admin mode is it possible
to save settings.
4.2 DLT-V72 with ADLoG Linux
You will find the configuration description for the ADLoG Standard Linux image at
www.advantech-dlog.com (Download menu, login required).
5 Wi-Fi settings
CAUTION
Radio wave emission due to incorrect Wi-Fi configuration.
Risks to health are possible due to incorrect radio wave emission if the
transmission power and the frequency are set incorrectly during the Wi-Fi
configuration.
Observe the applicable regulations for your deployment location/country with
regard to frequencies and the maximum permissible transmitting power.
Responsibility for this lies with the company operating the DLT-V72. The
regulatory authorities in the relevant country can provide information on this.
A default profile with basic settings for Wi-Fi operation is defined at the factory.
To create a custom profile, please use the Wi-Fi configuration program that is
preinstalled on your DLT-V72.
Depending on the Wi-Fi driver used, the following configuration programs are
available:
Laird Connection Manager (LCM)
Password: SUMMIT
(Upper case mandatory)
Windows Zero Configuration (WZC) No password required

Quick Start Guide: DLT-V72 Industrial PC
Advantech-DLoG
Quick Start Guide: DLT-V72, V1.00, PN 20DLDOCX88521E00
Page 4 / 8
6 Observe before installing
WARNING
Risk of injury and damage due to improper installation.
Observe the following important safety notice sections in the DLT-V72 User
Manual before installing the device:
−Installation of the DLT-V72 on vehicles
−Vehicle potential ratios
−
Electrically isolated installation
Recommend sequence for the mechanical installation
Requirement: The vehicle / installation location must be prepared (e.g. connection to
the ignition, correct voltage, etc.)
We recommend the following sequence for the mechanical and electrical installation:
−Determine a suitable mounting position for the DLT-V72.
−Secure device mounting at the vehicle / installation location.
−Connect external accessories to the DLT-V72.
−Install an easily accessible disconnecting device, such as a switch
close to the device.
−Connect all cables.
−Close the DLT-V72 with cable cover.
−Mount the DLT-V72 on the device mounting bracket
7 Cable connection, strain relief rail, cable cover
7.1 Inserting the rubber seal in the cable compartment
Place the rubber seal in the frame of the cable compartment (see figure).
Press the plugs of the rubber seal into the holes of the frame.
7.2 Plugging in and screwing on the power supply cable
Plug the power supply cable into the power supply
plug-in location.
Screw both mounting screws hand-tight.
Fold open the round cable passage in the rubber
seal.
Insert the power supply cable.

Quick Start Guide: DLT-V72 Industrial PC
Advantech-DLoG
Quick Start Guide: DLT-V72, V1.00, PN 20DLDOCX88521E00
Page 5 / 8
7.3 Securing the ground using ring tongue to the ground bolt
Secure the ring tongue of the power supply cable to the ground bolt:
ATTENTION
For correct grounding, it is important to have
the correct order of the components on the
ground bolt (from inside to outside):
1. Toothed washer (internal)
2. Ring tongue of the power supply cable
(flat side faces the DLT-V72 connector
panel)
3. Tightening the nut hand-tight.
7.4 Securing the power supply cable to the strain relief rail
Place one cable clip on the power supply cable.
Secure the cable clip to the strain relief rail using 2 mounting screws (ISO 4762-
M4x10-A2 cylinder-head screws).
Tighten the mounting screws alternatingly.
ATTENTION Tighten the mounting screws sufficiently but on no account pinch or
crush the cable. If you do, the cables may break or the cable insulation may get
damaged.
7.5 Connecting the USB, Ethernet and COM cables
Only use accessories that have been tested and approved by Advantech-DLoG for
the respective DLT-V72.
Proceed as described in section above (Securing the power supply cable).
1
2
3

Quick Start Guide: DLT-V72 Industrial PC
Advantech-DLoG
Quick Start Guide: DLT-V72, V1.00, PN 20DLDOCX88521E00
Page 6 / 8
7.6 Closing off unused cable openings
Close off all unused cable openings of the rubber seal using the accompanying
blind plugs so that they are sealed.
7.7 Attaching the cable cover
Place the cable cover in the DLT-V72 housing slot.
Screw the cylinder-head screws loosely into the holes of the cable cover.
Then fully tighten the screws alternatingly with 3 Nm torque.
8 Integrated UPS and battery pack (optional)
The DLT-V72 is optionally available with an integrated uninterrupted power supply
(UPS). The battery pack (lithium-ion technology) of the UPS is located in the battery
pocket up top on the device.
WARNING
Personal injury due to short-circuit, fire, chemical burns, toxic substances.
DLT-V72 devices with integrated UPS contain lithium-ion battery packs. These
can ignite if handled or stored improperly (risk of fire), cause chemical burns or
release toxic substances.
Use care when handling lithium-ion battery packs.
Do not damage lithium-ion battery packs; do not drill through and do not
crush or drop.
Do not allow water or other liquids to come into contact with the device
(exercise particular caution with corrosive liquids).
Do not allow it to come into contact with fire.

Quick Start Guide: DLT-V72 Industrial PC
Advantech-DLoG
Quick Start Guide: DLT-V72, V1.00, PN 20DLDOCX88521E00
Page 7 / 8
Environmental conditions / performance specifications battery packs
Battery pack type I, 2500 mAh battery capacity, order no. DL-BTRG79461600
Bridging time
Typically 20 minutes. (when battery pack is fully charged)
Operating temperature
-20 to +40 °C
Charging time
4 h (fully recharge a completely discharged battery pack)
Charging temperature
-10 to +30 °C (ambient temperature)
Storage temperature
-20 to +60 °C
Maximum output power
40 W
Battery voltage
7,2 V
Battery pack type II, 2000 mAh battery capacity, order no. DL-BTRG79461700
Bridging time
Typically 20 minutes. (when battery pack is fully charged)
Operating temperature
-30 to +50 °C
Charging time
4 h (fully recharge a completely discharged battery pack)
Charging temperature
-10 to +50 °C (ambient temperature)
Storage temperature
-30 to +60 °C
Maximum output power
40 W
Battery voltage
7,2 V
8.1 Charging the battery pack
Connect the properly installed DLT-V72 to the main supply voltage.
(Note: DLoG Config settings may affect the charging behavior of the DLT-V72).
ATTENTION:
The cable cover and the battery pocket of the DLT-V72 must be screwed together
properly. The device must be fully closed.
WARNING
Electric shock when charging the battery pack.
Do not connect damaged battery packs to the DLT-V72; do not charge.
Battery packs become warm while charging; this is normal. However, if they
become excessively hot, immediately disconnect the DLT-V72 from the
power source.
Do not continue to use the DLT-V72 if you notice an unusual level of heat or
an unusual smell during charging.
Provide for sufficient ventilation of the DLT-V72 during charging.
8.2 Replacing the battery pack
WARNING
Personal injury due to short-circuit, fire, chemical burns, toxic substances.
No third-party battery packs permitted.
Use only original battery packs from Advantech-DLoG.
The battery packs must be authorized/approved for the DLT-V72.
Do not use battery packs from any other Advantech-DLoG devices; they are not
compatible.
If battery packs from other manufacturers are inserted in the DLT-V72, the
warranty provided by DLoG GmbH for this device will be rendered void.

Quick Start Guide: DLT-V72 Industrial PC
Advantech-DLoG
Quick Start Guide: DLT-V72, V1.00, PN 20DLDOCX88521E00
Page 8 / 8
Procedure for replacing the battery pack
IMPORTANT: Switch off the DLT-V72 and disconnect the device from
the power supply.
Loosen the two screws of the battery cover using an Allen wrench.
Remove the battery cover.
Remove the battery pack.
Insert the new battery pack into the battery pocket.
Make sure that the removal tab of the battery pack is inside the sealing surface.
Then reattach the battery cover (tightening torque 2 Nm).
9 End-of-life device disposal / Recycling
DLT-V72 devices that are defective or ready for disposal are
considered to be special waste and can be recycled. They must not
disposed of with general/domestic waste
The lithium-ion batteries in DLT-V72 devices with an integrated UPS
are also special waste and recyclable. In the same way, they must not
be disposed of with general/domestic waste.
Proper disposal in accordance with local regulations is required.
Please contact the responsible authorities in your country/region to find
out about the applicable regulations, if necessary.
10 Technical customer support
E-Mail: [e-mail] Web: www.advantech-dlog.com
Phone: (+49) 89 / 41 11 91 999
DLoG GmbH
Industriestraße 15
D-82110 Germering
Quick Start Guide DLT-V72
PN: 20DLDOCX88521E00
V1.00
02/02/2016
Warranty conditions
For DLT-V72 industrial PCs, batteries and accessories the Advantech-DLoG TOB
regulations are valid (section Liability for defects -> limitation period for claims).
Find details at www.advantech-dlog.com.
Regulatory information, conformity
Please find regulatory information and a copy of the declaration of
conformity in the DLT-V72 User Manual at www.advantech-dlog.com.
by DLoG GmbH 2016. All rights reserved.
We reserve the right to make changes to this document at any time – and without prior
notice. DLoG GmbH is not liable for technical or printing errors or shortcomings in this
document. DLoG GmbH accepts no liability for damage caused directly or indirectly by
the delivery, performance or use of this document.