Advantech EIS2-EXTEND-A User manual

EIS2-EXTEND-A
Compact VDSL2-Extender
USER MANUAL

EIS2-EXTEND-A
i
Advantech B+B SmartWorx - Americas
707 Dayton Road
Ottawa, IL 61350 USA
Phone [phone]
Fax [phone]
Advantech B+B SmartWorx - European Headquarters
Westlink Commercial Park
Oranmore, Co. Galway, Ireland
Phone [phone]
Fax [phone]
www.advantech-bb.com
B+B SMARTWORX TECHNICAL SUPPORT
USA/Canada: 1 [phone] (Ottawa IL USA location)
(Monday - Friday, 7:00 a.m. to 7:00 p.m. CST)
Europe: [phone] (Ireland location)
(Monday - Friday, 8 a.m. to 5:00 p.m. GMT)
Email: [e-mail]
Web: www.advantech-bb.com

EIS2-EXTEND-A
ii
CONTENTS
B+B SMARTWORX TECHNICAL SUPPORT…………………………. i
List of Figures…………………………………………………………….. ii
List of Tables…………………………………………………………………ii
FCC RADIO FREQUENCY INTERFERENCE STATEMENT………… iii
WARRANTY……………………………………………………………….. iv
CONTENTS OF PACKAGE……………………………………………… 1
ABOUT THE EIS2-EXTEND-A…………………………………………… 2
HARDWARE INSTALLATION…………………………………………… 2
POWER……………………………………………………………………….3
DIP switch settings………………………………………………………… 3
LEDs…………………………………………………………………… 5
SPECIFICATIONS……………………………………………………….. 6
CERTIFICATIONS/APPROVALS………………………………………. 7
ELECTROSTATIC DISCHARGE PRECAUTIONS…………………….. 8
CERTIFICATIONS…………………………………………………………. 9
LIST OF FIGURES
Figure 1: DSW for enabled/disabled …………………………………………………………2
LIST OF TABLES
Table 2: Speed/Distance/SNR........................................................................4
Table 3: LEDs for VDSL2.................................................................................5
Table 4: LEDS for LAN.....................................................................................5

EIS2-EXTEND-A
iii
Table 5: Specifications .....................................................................................6
FCC RADIO FREQUENCY INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a
Class B computing device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which the user will be required to
correct the interference at his own expense.
Any changes or modifications not expressly approved by the
manufacturer could void the user’s authority to operate the equipment.
The use of non-shielded I/O cables may not guarantee compliance with
FCC RFI limits. This digital apparatus does not exceed the Class B limits
for radio noise emission from digital apparatus set out in the Radio
Interference Regulation of the Canadian Department of Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques
dépassant les limites applicables aux appareils numériques de classe B
prescrites dans le Règlement sur le brouillage radioélectrique publié par
le ministère des Communications du Canada.

EIS2-EXTEND-A
iv
WARRANTY
Effective for products of B+B SmartWorx shipped on or after May 1, 2013, B+B SmartWorx
warrants that each such product shall be free from defects in material and workmanship for
its lifetime. This limited lifetime warranty is applicable solely to the original user and is not
transferable.
This warranty is expressly conditioned upon proper storage, installation, connection,
operation and maintenance of products in accordance with their written specifications.
Pursuant to the warranty, within the warranty period, B+B SmartWorx, at its option will:
1. Replace the product with a functional equivalent;
2. Repair the product; or
3. Provide a partial refund of purchase price based on a depreciated value.
Products of other manufacturers sold by B+B SmartWorx are not subject to any warranty or
indemnity offered by B+B SmartWorx, but may be subject to the warranties of the other
manufacturers.
Notwithstanding the foregoing, under no circumstances shall B+B SmartWorx have any warranty
obligations or any other liability for: (i) any defects resulting from wear and tear, accident, improper
use by the buyer or use by any third party except in accordance with the written instructions or advice
of the B+B SmartWorx or the manufacturer of the products, including without limitation surge and
overvoltage conditions that exceed specified ratings, (ii) any products which have been adjusted,
modified or repaired by any party other than B+B SmartWorx or (iii) any descriptions, illustrations,
figures as to performance, drawings and particulars of weights and dimensions contained in the B+B
SmartWorx’ catalogs, price lists, marketing materials or elsewhere since they are merely intended to
represent a general idea of the products and do not form part of this price quote and do not constitute
a warranty of any kind, whether express or implied, as to any of the B+B SmartWorx’ products.
THE REPAIR OR REPLACEMENT OF THE DEFECTIVE ITEMS IN ACCORDANCE WITH THE
EXPRESS WARRANTY SET FORTH ABOVE IS B+B SMARTWORX’ SOLE OBLIGATION UNDER
THIS WARRANTY. THE WARRANTY CONTAINED IN THIS SECTION SHALL EXTEND TO THE
ORIGINAL USER ONLY, IS IN LIEU OF ANY AND ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED, AND ALL SUCH WARRANTIES AND INDEMNITIES ARE EXPRESSLY DISCLAIMED,
INCLUDING WITHOUT LIMITATION (I) THE IMPLIED WARRANTIES OF FITNESS FOR A
PARTICULAR PURPOSE AND OF MERCHANTABILITY AND (II) ANY WARRANTY THAT THE
PRODUCTS ARE DO NOT INFRINGE OR VIOLATE THE INTELLECTUAL PROPERTY RIGHTS OF
ANY THIRD PARTY. IN NO EVENT SHALL B+B SMARTWORX BE LIABLE FOR LOSS OF
BUSINESS, LOSS OF USE OR OF DATA INTERRUPTION OF BUSINESS, LOST PROFITS OR
GOODWILL OR OTHER SPECIAL, INCIDENTAL, EXEMPLARY OR CONSEQUENTIAL DAMAGES.
B&B ELECTRONIC SHALL DISREGARD AND NOT BE BOUND BY ANY REPRESENTATIONS,
WARRANTIES OR INDEMNITIES MADE BY ANY OTHER PERSON, INCLUDING WITHOUT
LIMITATION EMPLOYEES, DISTRIBUTORS, RESELLERS OR DEALERS OF B+B SMARTWORX
WHICH ARE INCONSISTENT WITH THE WARRANTY, SET FORTH ABOVE.

EIS2-EXTEND-A
1
CONTENTS OF PACKAGE
Part Numbers: EIS2-EXTEND-A
The package includes:
• EIS2-EXTEND-A
• 12 VDC External Power Adapter
• DIN Rail kit
• Panel Mount kit
•RJ-45 to RJ-11 cable adapter
•Removable terminal block

EIS2-EXTEND-A
2
ABOUT THE EIS2-EXTEND-A
The EIS2-EXTEND-A is a Long Reach Ethernet Extender to utilize existing copper cabling
infrastructure (twisted pair), extending Ethernet to up to 1200 meters over VDSL2. Applications
such as IP-based Internet connections, video-on-demand and voice services can benefit from the
EIS2-EXTEND-A VDSL2 extenders. It offers one 10/100Mbps Ethernet port and one VDSL2 port,
and is a PNP, unmanaged device.
HARDWARE INSTALLATION
EIS2-EXTEND-A Extenders
The EIS2-EXTEND-A VDSL2 extenders must be set up in pairs for end
to end connectivity. The VDSL2 extender offers DIP Switches (DSW),to
set one as a Master for the CO (Central Office) and one as an RT
(Remote) for the CPE (Customer Premises Equipment). The DSW #1
labeled SNR 9db/SNR 6db must be set as follows:
CO:SNR 6db set to enabled CPE: SNR 9db set to enabled
Figure 1: DSW for enabled/disabled

EIS2-EXTEND-A
3
Once the two devices are set to CO/CPE, the next step is to connect
each of them with CAT 5 Ethernet cabling on the RJ-45 port labeled
LAN. Power the devices with the power supply (included). Next, connect
the two EIS2-EXTEND-A devices with the CAT 3 cabling to each port
labeled VDSL2.
Once the LEDs are established, you can set the other DSW depending
on your application requirements for best functionality.
POWER
The EIS2-EXTEND-A includes an AC to DC power adapter and a
removable terminal block.
DIP SWITCH SETTINGS
The DIP Switches can be set according to whether you need to cover speed
vs. reach, symmetric transmission or asymmetric transmission for data, and
SNR (Signal to Noise Ratio) for line (channel) noise. Each EXTENDER must
be set as a CO (Central Office) or RT (Remote).
DSW#1 allows you to set up one extender as a Master (CO) and one as a
Remote (RT) unit.

EIS2-EXTEND-A
4
DSW #2 can be set for High Speed Mode or in a Long Reach Mode. This is
based on Profiles 30a and 17a, respectively.
DSW #3 allows you to set upstream/downstream as symmetrical or
asymmetrical.
DSW #4 allows you to select which decibel value that provide the best
protection against line (channel) noise.
Table 1: DIP Switch Selections
The DSW settings will determine the speed/distance/SNR.
Table 2: Speed/Distance/SNR

EIS2-EXTEND-A
5
LEDS
LEDS for VDSL2
Table 3: LEDs for VDSL2
LEDS for LAN (RJ-45 port)
Table 4: LEDS for LAN

EIS2-EXTEND-A
6
SPECIFICATIONS
Connectors
RJ-45 (1 port)
CAT 3, phone wiring
RJ-45 (1 port)
CAT 5, Ethernet cabling
Environmental -- Intended for indoor and outdoor use.
Operating Temperature
0-45°C
Storage Temperature
0-45°C
Operating Humidity
5% to 95% non-condensing
LED Indicators
VDSL2
Power
LNK
Data transmission
OT/RT
Green: ON no color: OFF
Green: ON no color: OFF
Blinks steadily
ON/OFF dependent on CO or CPE
DSW #1
LED Indicators LAN
Power
LNK
FUL (duplex)
SP (Speed)
Green: ON no color: OFF
Green: ON no color: OFF
Green: ON: FDX OFF :HDX
Green ON: 100Mbps OFF: 10Mbps
Power Supply
External power adapter
12 VDC
Table 5: Specifications

EIS2-EXTEND-A
7
CERTIFICATIONS/APPROVALS
Certifications
FCC
FCC Part 15 Class A
CE
EN60950
EN61000-6-1
Generic Standards for Residential,
Commercial, & Light Industrial
EN61000-4-2
ESD (15kV air & 4kV contact)
EN61000-4-3
RFI
EN61000-4-4
EFT
EN61000-4-5
Surge
EN61000-4-6
CI
EN61000-4-8
Power Frequency Magnetic
EN61000-4-11
Voltage Dips & Interruptions
EN60255-21-1
Vibration
EN60255-21-2
Shock
Shock and
Vibration
IEC 68-2-6 and IEC 68-2-7 Shock: 30g, 11
ms half sine wave, 18 shocks; Vibration: 0.5
mm p-p, 10 to 60 Hz
Radiated
Immunity
10 V/m, 80-2700 MHz (EN61000-6-2) or
Equivalent
Regulatory Approvals
ROHS and WEEE Compliant
Table 6: Certifications

EIS2-EXTEND-A
8
ELECTROSTATIC DISCHARGE PRECAUTIONS
Electrostatic discharge (ESD) can cause damage to any product, add-in
modules or stand-alone units, containing electronic components. Always
observe the following precautions when installing or handling these kinds
of products:
Do not remove unit from its protective packaging until ready to install.
Wear an ESD wrist grounding strap before handling any module or
component. If the wrist strap is not available, maintain grounded contact
with the system unit throughout any procedure requiring ESD protection.
Hold the units by the edges; do not touch the electronic components or
gold connectors.
After removal, always place the boards on a grounded, static-free
surface, ESD pad or in a proper ESD bag. Do not slide the modules or
stand-alone units over any surface.
WARNING! Integrated circuits and fiber optic components
are extremely susceptible to electrostatic discharge
damage. Do not handle these components directly unless
you are a qualified service technician and use tools and
techniques that conform to accepted industry practices.

EIS2-EXTEND-A
9
CERTIFICATIONS
CE: The products described herein comply with the Council Directive on
Electromagnetic Compatibility (2004/108/EC). For further details, contact
B+B SmartWorx.
European Directive 2002/96/EC (WEEE) requires that any equipment that
bears this symbol on product or packaging must not be disposed of with
unsorted municipal waste. This symbol indicates that the equipment should
be disposed of separately from regular household waste. It is the
consumer’s responsibility to dispose of this and all equipment so marked
through designated collection facilities appointed by government or local
authorities. Following these steps through proper disposal and recycling will
help prevent potential negative consequences to the environment and
human health. For more detailed information about proper disposal, please
contact local authorities, waste disposal services, or the point of purchase
for this equipment.
____________________________________________________
© 2017 B+B SmartWorx. All rights reserved. The information in this document is
subject to change without notice. B+B SmartWorx assumes no responsibility for any
errors that may appear in this document. XXXXXXX is a trademark of B+B
SmartWorx. Other brands or product names may be trademarks and are the property
of their respective companies.
Document #:EIS2-EXTEND-A_R0_0917m