Advantech B+B SmartWorx IE-MiniFiberLinX-II Series User manual

1-888-948-2248 | Europe: [phone]
advantech-bb.com
707 Dayton Road | PO Box 1040 | Ottawa, IL 61350
Phone: [phone] | Fax: [phone]
www.advantech-bb.com | E-mail: [e-mail]
Fast and easy on the web: www.advantech-bb.com
QUICK START
GUIDE
Document Number: IE-MiniFiberLinX-II-standard_56-85722-00 A2_3317qsg
Before you begin, be
sure you have the following:
IE-MiniFiberLinX-II series
Managed Optical Demarcation Device (Standard)
Setting up a managed device in iView2
(Complete Step #3 rst.)
1. Launch iView2. The iView2 application automatically
discovers B+B SmartWorx devices on the same subnet.
Simply click on the product name to bring up the
conguration screen. If the device does not appear, go to
the next step.
2. If a group name has already been set up, go to step 4.
Otherwise, click on the Add Element icon on the iView2
toolbar, enter a group name and click on Add.
3. Click on the Add Element icon.
4. Enter the IE-MiniFiberLinX-II’s IP address, select IE-
MiniFiberLinX from the pulldown menu and click on Add.
5. The IE-MiniFiberLinX-II will appear on the left. Click on
the product name to congure.
6. If no IE-MiniFiberLinX-II appears, but the device can be
pinged, contact B+B SmartWorx technical support.
Add Element
Advanced Conguration iView2
4
To remove the converter from the DIN rail, use a flat-head
screwdriver in the slot to gently pry the converter from the rail.
Use the screws to attach the DIN clips to the IE-
MiniFiberLinX-II, then snap the converter to the DIN rail.
NOTE: DIN clip & screws sold separately - designed for use on DIN-35 rail.
DIN RAIL Mounting The Device
5
+ IE-MiniFiberLinX-II
+ 100/240V AC input, 5V power adapter
power supply (included)
+ Console port mini-jack adapter (included)
Recommended Accessories
iView2Network
Management Software
-Free download
Ethernet Cables
- Sold separately
Model# 806-39105
- DIN rail clip & 2 screws
- Sold separately

Product Overview
Power Options
Connecting Fiber and
Twisted Pair Cables
1
2
IE-MiniFiberLinX-II includes multiple powering options.
Users can choose any of the following three options, or
more than one, for power redundancy:
1. A country-specic, high-reliability power adapter
(included). 100/240V AC input, 5V DC output.
2. IEEE 802.3af Power-over-Ethernet PD (“Powered
Device”) standard; draws power from PoE PSE (“Power
Sourcing Equipment”).
3. 4-terminal DC power block.
1. Connect the ber cable to the ber port.
FX L NK /ACT:
Glows green when a link is established on the ber port;
Blinks green when activity is detected on the ber port.
2. Plug in the RJ-45 cable to the Twisted Pair port.
T X LN K /AC T:
Glows amber when a link is established on the copper port;
Blinks amber when activity is detected on the copper port.
1. Set the computer / terminal for VT-100 emulation with the
following settings: 38.4K baud, 8 data bits, 1 stop bit, no
parity, no ow control.
2. Connect the RS232 cable to the Console port, backside
of the unit.
3. Start the Hyperterminal session and press the Enter Key.
Conguration Option #1:
Hyperterminal Session
3a
• Computer must be attached to the local LAN connection
via the ber port and on the same Subnet Mask.
• Start iCong and scan for devices.
• A new device will show IP Address 10.10.10.10 with its
name “IE-MiniFiberLinX-II”.
• Open Session by typing in the USER NAME and
USER PASSWORD.
(admin / admin are the defaults)
• Set the IP Address, Subnet Mask and Default Gateway
as required.
Conguration Option #2:
iCong
3b
• Bandwidth Control
• Q-in-Q Support
• VLANS
• LFPT (Link Fault Pass-Through)
• Last Gasp (Telco with Last Gasp)
• Telco power (both models)
Note: The IE-MiniFiberLinX-II series is a CPE device, and is not
recommended to be installed in pairs. It can be installed as
a Remote device that is congured as a Host, such as the
iMcV-FiberLinX-II.
Note: For more detailed instructions, please refer to the
installation manual. Software is downloadable from the
website.
Fiber LED
Link/Activity
Twisted Pair LED
Link/Activity
Fiber Port
XMT RCV
Twisted Pair
(PD) Port
4. Set IP Address, Subnet Mask, Default Gateway and
SNMP Community String if direct SNMP/ Telnet
management is required.
5. Set Mode and Ethernet Port Cong.
6. Set Password if Craft port security is required (optional).
7. Type “reboot” for changes to take effect.
10.10.10.10-IE-MiniFiberLinX-II
Will be added to the list.
PoE (PD) Port
5 to 24 VDC
Ground
(common) 12 to 48 VDC