Advantech FWA-3232 Installation and operation manual

FWA-3232 1RU Network Application Platform X86-Based Intel®
XeonTM series and 4th generation CoreTM i7/i5/i3 processor
Startup manual
Before installation, ensure that the following materials
havebeen received:
One FWA-3232 Internet Security Platform
One box of accessories
One warranty certificate
If any of these items are missing or damaged, please
contactyour distributor or sales representative immediately.
Note: Acrobat Reader is required to view any PDF file.
Acrobat Reader can be downloaded at:
www.adobe.com/Products/acrobat/readstep2. html
(Acrobat is a trademark of Adobe)
Main Board Functions
CPU: Intel® XeonTM E3-1275/E3-1225/E3-1268LV3, 4th
Gen Intel® CoreTM Processors i7-4790S, i7-4770S,
i7-4770TE, i5-4590S,i5-4570S,i5-4590T,i5-4570TE,
i3-4360,i3-4330, i3-4350T,i3-4340TE,i3-4330TE, Intel®
Pentium® Processor G3420,G3320TE and Intel® Celeron®
Processor G1820, G1820TE(LGA1150)
Chipset: Intel® C226/H81 PCH
Memory: Dual channel DDR3 1333/1066 MHz ECC(Xeon®
processors only) Un-buffered memory, up to 32GB
PCI-Express:1xPCIe x8 gen.3，1xPCIe x4 gen.2 for FH/HL
PCI-e cards
Network Connectivity:
NMC : up to 2x NMC Modules with PCI-e x8 gen.3
interfaces
Ethernet : 8 or 6 x Intel I210-AT 10/100/1000 Mbps
Ethernet
Mass Storage: 2 x 2.5" internal ,1 x 3.5”SATA HDD/SSD,
speed up to 6Gb/s, 1x Half/Full Size mSATA module, speed
up to 6GB/S
Peripherals:
LCD Module:32x128 graphic display,5 buttons
Console:1 x RJ45 Console port
USB:2 x USB2.0 Type A connector
TPM: TPM1.2(Infineon_SLB9635TT)
Power supply:300W, AC/DC redundant ,300W/250w AC
Single power
Dimensions(W x H x D): 430 x 44 x 500 mm/ 430 x 44 x 375
mm
Weight:10KG/6KG
Environment: Operating Non-operating
Temperature: 0 ~ 40℃-40 ~ 60℃
(32 ~ 104°F) (-40 ~ 140°F)
Humidity: 5 ~ 85% @ 40℃5 ~ 95% @ 40℃(104℉)
Specification
Packing List

Express Modules
Interface: one LCM with 5 buttons, 1 console port, 2 LAN
RJ45 connectors, 1 USB connectors and one power
button.
Express Modules:4 x PCI-E Gen.3 NMC slots, Support 4
ports GE by RJ-45, 4 ports GE by SFP, 2 ports 10GE by
SFP+ and Acceleration card.
Dimensions (W x D): 72 x 172 mm
Figure1: 0107 4 ports RJ45 GE Module
Figure2: NMC-0108 4 ports SFP GE Module
Figure3: NMC-1004 2 ports SFP+ 10GE Module
Support Advantech NMCs as the form shows：
NMCs
Ethernet
Controller
IO
Interface
NMC-0107
Intel
I350-AM4 x1
4 GbE LAN
RJ-45
NMC-0108
Intel
I350-AM4 x1
4 GbE LAN
SFP
NMC-0801
Intel 82580EB
x2
8 GbE LAN
RJ-45
NMC-0108
Intel
I350-AM4 x1
4 GbE LAN
SFP
NMC-1004E
Intel 82599ES
x1
2 10G LAN
SFP+
NMC-4001
Intel 82599ES
x2
4 10G LAN
SFP+
NMC-0804
Intel
I350-AM4 x2
8 GbE LAN
SFP
NMC-0805
Intel
I350-AM4 x2
8 GbE LAN
4SFP+4RJ45
FWA-3232 Internet Security Platform
Front view
Back view
Specification

Installing the CPU
1. Locate the CPU sockets on the board
2. Taking one CPU at a time, remove the protective shield, if
present, and press the load lever and move it out till it is clear of
the retention tab, and raise it.
3. Make sure that alignment triangle on the CPU lines up with
the correct corner on the socket, and ease the CPU into place.
4. Close the load plate and push the load lever back down until
it engages the retention tab.
Installing the heatsink and air scoop
1. Take out the heatsink, air scoop,2pcs of silvery screws and
4pcs of black screws;Place the heatsink into air scoop and lock
them with the 4pcs black screw as the picture shows.
2. Put the air scoop and heatsink on the board. Insert and
tighten the heatsink screws on the diagonal. Then make the
scoop fixed on the chassis with the silvery screws.
Installation

Installing the the Riser Cards
1. Remove the screws and HDD bracket signed by the arrows.
移除下图一箭头位置之机箱背面的两颗螺丝，
2. Release four screws and take out the bracket.
3．Release screws of the first IO bracket and remove the first IO
bracket.
4. Fix the PCI-e Card on the I/O interface, and insert them into
the Riser Card.
5. Fix 4 screws into the tapped hole signed as the yellow arrow.
Installing the 3.5’HDD
1. Take out the HDD rubbers and screws 6pcs each from the
accessory box ;
2. Fix the rubbers on the HDD bracket as picture shows;
3. Fix the 3.5”HDD on the bracket with the screws as below
picture;
4. Make the bracket, which has attached HDD, be set up onto
the original location in the chassis;
5. Take a SATA data cable from the accessory box, and
Installation

connect it as the picture shows; Then connect the SATA power
cable to HDD interface.

Installing the 2.5’ HDD
1．Take out the HDD rubbers and screws from the accessory
box ,and push the rubbers into the hole on the bracket;
2．Install the 2.5’ HDD in the bracket with four screws.
3．Fix the HDD and bracket in the chassis. SATA port need be
forward to the power. Connect and place the cables as the
picture shows.
Installing Express Modules
1．Release the 2 screws. Push the lower half of the baffle and
take it out；
2．Insert the express module into the case and tighten the
screws.
Installation

Connection for DC power source
Attention:
Only trained service personnel are authorized to install and
remove the -36- -60 volt DC power supply ,and make the
connections to and disconnections from the -36- -60 volt DC
power source. The customer is responsible for ensuring that
only trained service personnel are authorized to install and
remove the -36- -60 volt DC power cable.
To Connect Power supply:
The DC supply source for the equipment power supplied shall
be an UL certified power source and suitable for specification
provided by the manufacturer. Please use the jacketed power
cable with 16AWG or 11Amp, 60 volt to connect between the
equipment and the DC power source.
1. Turn off DC power source and equipment that is to be
connected this product.
2. Ensure DC power source connected earthed cable.
3. Connect the earthed cable which is of AWG16 min. green
and yellow wire of earth of building to the protective
earthed terminal of the equipment.
4. Connect power cables to the power source.
5. Ensure correct polarity.
6. Turn on the power source.
To Disconnect Power supply:
1. Turn off DC power source and equipment.
2. Disconnect the power cord from equipment.
3. Remove the earthed cable from protective earthed
terminal of the equipment.
For YH-5301K
RTN is +, -36- -60VDC is –
For DM1Y2-5300V2H
The board has a number of jumpers that allow you to configure
your system to suit your application. The table below lists the
function of each of the jumpers and connectors.
Jumper
Name
Pin
Default Setting
Function
JCMOS1
1-2
Jumper short
Normal status
2-3
Open
Clear CMOS
8051_JTAG1
3-5
Jumper short
Disable stand bypass
Open
Enable stand bypass
8051_JTAG2
8051_JTAG3
8051_JTAG4
3-5
Jumper short
Disable Adv bypass
Open
Enable adv bypass
BPLED1_2
BPLED3_4
BPLED5_6
1-2
short
Bypass LED indication
by LAN LED
2-3
short
Bypass LED indication
by LED cable
PSON1
1-2
Jumper short
AT mode
2-3
Jumper short
ATX mode
JVGPIO1
1-2
Jumper short
5V power for GPIO
2-3
Jumper short
3.3V power for GPIO
JC8051_12
JC8051_34
JC8051_56
1-2
Jumper short
Adv bypass
2-3
Open
NC
Jumper and Connectors
Installation

JCMOS1
Pins
Function
1-2
Normal status
2-3
Clear CMOS
Default setting:1-2 Jumper Short
JUART1_SW1
Pins
Function
1-2
UART1 SWITCHED BY COM_SOL_CTRL
2-3
WHEN BMC LOADED, BMC_DETECT# CHANGE
TO 0, UART1 SWITCHED TO SOL
Default setting:1-2 Jumper Short
ATX12V1
Pins
Function
1
GND
2
GND
3
12V
4
12V
ATXPWR1
Pins
Function
1
3.3V
2
3.3V
3
GND
4
5V
5
GND
6
5V
7
GND
8
POK
9
5VSB
10
12V
11
12V
12
3.3V
13
3.3V
14
-12V
15
GND
16
PSON
17
GND
18
GND
19
GND
20
-5V
21
5V
22
5V
23
5V
24
GND
Jumper and Connectors

USB3_4
Pins
Function
1
VCC
2
VCC
3
Data9-
4
Data8-
5
Data9+
6
Data8+
7
GND
8
GND
9
GND
10
Key
LPC1
Pins
Function
1
LPC_FRAME#
2
GND
3
LAD0
4
CLK
5
LAD1
6
SERIRQ
7
LAD2
8
RESET#
9
LAD3
10
+V3.3
SYSFAN1~SYSFAN4
Pins
Function
1
GND
2
Power
3
FANIN
4
PWM
VGA1
Pins
Function
1
R
2
VCC
3
G
4,9,11,13,15
GND
5
B
6,7
NC
8
DDAT
Jumper and Connectors

10
HS
12
VS
14
DCLK
16
GND_V
JTAG1
Pins
Function
1
JTAG_TCK
2
VCC3
3
JTAG_TMS
4
GND
5
JTAG_TDI
6
GND
7
JTAG_TDO
8
GND
9
JTAG_RST#
10
NC

KBMS1
Pins
Function
1
MSCK
2
+V5_SB
3
GND
4
MSDT
5
KBDT
6
KBCK
GPIO1
Pins
Function
1
GPIO0
2
GPIO4
3
GPIO1
4
GPIO5
5
GPIO2
6
GPIO6
7
GPIO3
8
GPIO7
9
VCC
10
GND
Jumper and Connectors

、
Software List:
Windows Server2008 R2 64bit
Windows 7 Ultimate English 32 bit
Red Hat Enterprise 6.1 32bit/64bit
Software Installation

Board Placement

1. Read these safety instructions carefully.
2. Keep this user manual for later reference.
3. Disconnect this equipment from AC outlet before cleaning. Do not use liquid or spray detergents for cleaning.
4. For pluggable equipment, the power outlet shall be installed near the equipment and shall be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or letting it fall could cause damage.
7. Do not leave this equipment in an environment unconditioned where the storage temperature under 0℃(32℉) or above 40℃
(104℉), it may damage the equipment.
8. The openings on the enclosure are for air convection hence protects the equipment from overheating. DO NOT COVER THE
OPENINGS.
9. Make sure the voltage of the power source is correct before connecting the equipment to the power outlet.
10. Place the power cord such a way that people can not step on it. Do not place anything over the power cord. The voltage and
current rating of the cord should be greater than the voltage and current rating marked on the product.
11. All cautions and warnings on the equipment should be noted.
12. If the equipment is not used for long time, disconnect it from the power source to avoid being damaged by transient overvoltage.
13. Never pour any liquid into ventilation openings. This could cause fire or electrical shock.
14. Never open the equipment. For safety reasons, the equipment should be opened only by qualified service personnel.
15. If any of the following situations arises, get the equipment checked by service personnel:
a. The power cord or plug is damaged.
b. Liquid has penetrated into the equipment.
c. The equipment has been exposed to moisture.
d. The equipment does not work well or you cannot get it to work according to user manual.
e. The equipment has been dropped and damaged.
f. The equipment has obvious signs of breakage.
16. CAUTION: The computer is provided with a battery-powered real-time clock circuit. There is a danger of explosion if battery is
incorrectly replaced. Replace only with same or equivalent type recommended by the manufacture. Discard used batteries according
to the manufacturer’s instructions.
17. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
18. CAUTION: Always completely disconnect the power cord from your chassis whenever you work with the hardware. Do not make
connections while the power is on. Sensitive electronic components can be damaged by sudden power surges.
Also products with redundant power , please pay more attention.
Safety Instructions

19. CAUTION: Always ground yourself to remove any static charge before touching the motherboard, backplane, or add-on cards.
Modern electronic devices are very sensitive to static electric charges. As a safety precaution, use a grounding wrist strap at all
times. Place all electronic components on a static-dissipative surface or in a static-shielded bag when they are not in the chassis.
20. CAUTION: Any unverified component could cause unexpected damage. To ensure the correct installation, please always use
the components (ex. screws) provided with the accessory box.

21. “Rack Mount Instructions - The following or similar rack-mount instructions are included with the installation instructions:
A) Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack
environment may be greater than room ambient. Therefore, consideration should be given to installing the equipment in an
environment compatible with the maximum ambient temperature (Tma) specified by the manufacturer.
B) Reduced Air Flow - Installation of the equipment in a rack should be such that the amount of air flow required for safe operation of
the equipment is not compromised.
C) Mechanical Loading - Mounting of the equipment in the rack should be such that a hazardous condition is not achieved due to
uneven mechanical loading.
D) Circuit Overloading - Consideration should be given to the connection of the equipment to the supply circuit and the effect that
overloading of the circuits might have on overcurrent protection and supply wiring. Appropriate consideration of equipment
nameplate ratings should be used when addressing this concern.
E) Reliable Earthing-Reliable earthing of rack-mounted equipment should be maintained. Particular attention should be given to
supply connections other than direct connections to the branch circuit (e.g. use of power strips).”