Advantech MIO-3110 Installation and operation manual

MIO-3110 Startup Manual 1
MIO-3110 Mini-PCI to USB Interface Connection Hub 430TX/SODIMM/LAN/USB/CRT/LCD/COM/DOC
CM-3351
S
B
MIO-3110 Mini-PCI to USB
Interface Connection Hub
Startup Manual
Advantech introduces its new MIO module, MIO-3110 with
Mini-PCI interface for advanced USB interface connection
hub.
Before you begin installing your card, please make sure
that the following materials have been shipped:
If any of these items are missing or damaged,
contact your distributor or sales representative
immediately
.
• Mini PCI Type III Interface
• NEC µPD720101 USB 2.0 Host Controller
• Provides Five USB 2.0 Ports up to 480Mbps
• Provides four USB 2.0 Ports
• Supports both USB 2.0 & USB 1.1 devices
Mechanical and Environmental
• Power requirement: +5V DC
• Size: 50.8mm x 59.6mm
• Operating Temperature: 32°F ~ 140°F (0°C ~ 60°C)
• Speed:Supports high-speed (480Mbps), full-speed
(12Mbps), and low-speed1.5Mbps) data rate
Introduction Specifications
Packing list
• 1 MIO-3110 Mini-PCI USB interface connection hub
• 1 Startup manual
• 1 CD ROM for MIO-3110 Driver
• 1 USB cable
Cable for USB 4 PORTS/10P-
2.0MM*2 30.5CM
p/n: 1700000601
Note 1: Acrobat Reader is required to view any PDF
file. Acrobat Reader can be downloaded at:
www.adobe.com/products/acrobat/
readstep2.html(Acrobat is a trademark of
Adobe.)
For more information on this and other Advantech
products, please visit our website at:
http://www.advantech.com
http://www.advantech.com/eplatform
For technical support and service, please visit our
support website at:
http://www.advantech.com/support
This manual is for the MIO-3110 series Rev. A1.
Part No.2006M31100 1st Edition
Aug. 2006

2 MIO-3110 Startup Manual
The table below lists the function of each of the jumpers
and connectors.
Jumpers & Connectors
USB Connector (CN1)
Pin Signal Pin Signal
1 USB 2 +5V 2 USB 1 +5V
3 USB D2- 4 USB D1-
5 USB D2+ 6 USB D1+
7 GND 8 GND
9GND
USB Connector (CN2)
Pin Signal Pin Signal
1 USB 4 +5V 2 USB 3 +5V
3 USB D4- 4 USB D3-
5 USB D4+ 6 USB D3+
7 GND 8 GND
9GND
USB Connector (CN3) optional
Pin Signal Pin Signal
1 USB 5 +5V 2 USB D5-
3 USB D5+ 4 GND
5GND 6
Power Connector (JP1)
Pin Signal Pin Signal
1 N.C. 2 GND
3GND 4 +5V

3 MIO-3110 Startup Manual
Locating connector (component side)
Locating connector (solder side)
Board Layout

4 MIO-3110 Startup Manual
Mechanical Drawing (component side)
Mechanical Drawing (solder side)

MIO-3110 Startup Manual 5
FCC This device complies with the requirements in part 15 of the FCC rules: Operation is subject to the fol-
lowing two conditions:
1.This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undes-
ired operation
This equipment has been tested and found to comply with the limits for a Class A digital device, pur-
suant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications. Operation of
this device in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his/her own expense. The user is advised that any equipment
changes or modifications not expressly approved by the party responsible for compliance would void
the compliance to FCC regulations and therefore, the user's authority to operate the equipment.
Caution!
Achtung!
There is a danger of a new battery exploding if it is incorrectly installed. Do not attempt to recharge,
force open, or heat the battery. Replace the battery only with the same or equivalent type recom-
mended by the manufacturer. Discard used batteries according to the manufacturer’s instructions.