Advantech ITA-8100 User manual

User Manual
ITA-8100 / ITA-8120
Series
EN 50155 10.4" / 12.1" Panel PC
with Intel Atom® Processor for
Railway Applications

ITA-8100 / ITA-8120 User Manual ii
Copyright
The documentation and the software included with this product are copyrighted 2020
by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right
to make improvements in the products described in this manual at any time without
notice. No part of this manual may be reproduced, copied, translated, or transmitted
in any form or by any means without the prior written permission of Advantech Co.,
Ltd. The information provided in this manual is intended to be accurate and reliable.
However, Advantech Co., Ltd. assumes no responsibility for its use, nor for any
infringements of the rights of third parties that may result from its use.
Acknowledgments
The ITA-8100 and ITA-8120 are trademarks of Advantech Co., Ltd.
All other product names or trademarks are properties of their respective owners.
Product Warranty (2 years)
Advantech warrants the original purchaser that each of its products will be free from
defects in materials and workmanship for two years from the date of purchase.
This warranty does not apply to any products that have been repaired or altered by
persons other than repair personnel authorized by Advantech, or products that have
been subject to misuse, abuse, accident, or improper installation. Advantech
assumes no liability under the terms of this warranty as a consequence of such
events.
Because of Advantech’s high quality-control standards and rigorous testing, most
customers never need to use our repair service. If an Advantech product is defective,
it will be repaired or replaced at no charge during the warranty period. For out-of-war-
ranty repairs, customers are billed according to the cost of replacement materials,
service time and freight. Please consult your dealer for more details.
If you believe your product is defective, follow the steps outlined below.
1. Collect all the information about the problem encountered. (For example, CPU
speed, Advantech products used, other hardware and software used, etc.) Note
anything abnormal and list any messages displayed onscreen when the prob-
lem occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information readily available.
3. If your product is diagnosed as defective, obtain a return merchandise authori-
zation (RMA) number from your dealer. This allows us to process your return
more quickly.
4. Carefully pack the defective product, a completed Repair and Replacement
Order Card, and a proof of purchase date (such as a photocopy of your sales
receipt) into a shippable container. Products returned without a proof of pur-
chase date are not eligible for warranty service.
5. Write the RMA number clearly on the outside of the package and ship the pack-
age prepaid to your dealer.
Part No. 2001810001 Edition 2
Printed in Taiwan July 2020

iii ITA-8100 / ITA-8120 User Manual
Technical Support and Assistance
1. Visit the Advantech website at http://support.advantech.com to obtain the latest
product information.
2. Contact your distributor, sales representative, or Advantech's customer service
center for technical support if you need additional assistance. Please have the
following information ready before calling:
Product name and serial number
Description of your peripheral attachments
Description of your software (operating system, version, application soft-
ware, etc.)
A complete description of the problem
The exact wording of any error messages
Safety Instructions
1. Read these safety instructions carefully.
2. Retain this user manual for future reference.
3. Disconnect this equipment from the power outlet before cleaning. Use only a
damp cloth for cleaning. Do not use liquid or spray detergents.
4. For pluggable equipment, the power outlet socket must be located near the
equipment and easily accessible.
5. Protect the equipment from humidity.
6. Place the equipment on a reliable surface during installation. Dropping or letting
the equipment fall may cause damage.
7. The openings on the enclosure are for air convection. Protect the equipment
from overheating. Do not cover the openings.
8. Ensure that the voltage of the power source is correct before connecting the
equipment to a power outlet.
9. Position the power cord away from high-traffic areas. Do not place anything over
the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the power source
to avoid damage from transient over-voltage.
12. Never pour any liquid into an opening. This may cause fire or electrical shock.
13. Never open the equipment. For safety reasons, the equipment should be
opened only by qualified service personnel.
14. If one of the following occurs, have the equipment checked by qualified service
personnel:
The power cord or plug is damaged.
Liquid has penetrated into the equipment.
The equipment has been exposed to moisture.
The equipment is malfunctioning, or does not operate according to the user
manual.
The equipment has been dropped and damaged.
The equipment shows obvious signs of breakage.
15. Do not leave the equipment in an environment with a storage temperature of
below -40 °C (-40 °F) or above 70 °C (158 °F) as this may cause damage. The
equipment should be kept in a controlled environment.

ITA-8100 / ITA-8120 User Manual iv
16. CAUTION: The battery is at risk of exploding if incorrectly replaced. Replace
only with the same type recommended by the manufacturer or an equivalent.
Discard used batteries according to the manufacturer’s instructions.
17. CAUTION: To avoid risk of electric shock, this equipment must only be con-
nected to supply mains with protective earthing.
In accordance with IEC 704-1:1982 specifications, the sound pressure level at the
operator's position does not exceed 70 dB (A).
DISCLAIMER: These instructions are provided in accordance with IEC 704-1. Advan-
tech disclaims all responsibility for the accuracy of any statements contained herein.
Consignes de sécurité
1. Lisez attentivement ces consignes de sécurité.
2. Gardez ce manuel pour référence future.
3. Déconnectez cet équipement de toute prise secteur avant de le nettoyer. Utili-
sez un chiffon humide. Ne pas utilisez de liquide ou de sprays détergents pour
le nettoyage.
4. La prise de courant doit être située près de l'équipement et doit être facilement
accessible.
5. Gardez cet équipement à l’abri de l'humidité.
6. La chute de l’équipement pouvant l’endommager, celui-ci doit être installé sur
une surface stable.
7. Les ouvertures du boîtier sont nécessaires au refroidissement de l’appareil.
Veillez à protéger l'appareil contre la surchauffe. Ne pas couvrir less ouvertures.
8. Assurez-vous que la tension de la source d'alimentation est correcte avant de
brancher l'appareil à la prise de courant.
9. Placez le cordon d'alimentation de manière à éviter que des personnes
marchent dessus. Veillez à ce qu’aucun objet ne soit placé sur le cordon d’ali-
mentation.
10. Tous les conseils et avertissements concernant ce matériel et son utilisation
doivent être lus et compris.
11. Si l'appareil n’est pas utilisé pendant une longue période, débranchez-le de la
source d'alimentation pour éviter les dommages causés par des surtensions
transitoires.
12. Ne jamais verser de liquide dans une ouverture. Cela peut provoquer un
incendie ou un choc électrique.
13. Ne jamais ouvrir l'équipement. Pour des raisons de sécurité, l'équipement ne
peut être ouvert que par du personnel qualifié.
14. Si l'une des situations suivantes se présente, faites vérifier le matériel par le
personnel de service:
Le cordon d'alimentation ou la prise est endommagé.
Du liquide a pénétré dans l'appareil.
L'équipement a été exposé à l'humidité.
L'équipement ne fonctionne pas bien, ou vous ne pouvez pas le faire
fonctionner selon le manuel d'utilisation.
L'appareil est tombé et est endommagé.
L'équipement présente des signes évidents de casse.
15. Ne pas laissez ce matériel dans un environnement où la température de stock-
age peut descendre en dessous de -40 °C (-40 °F) ou être supérieure à 70 °C
(158 °F). Ceci pourrait endommager l'équipement. L'équipement doit être main-
tenu dans un environnement contrôlé.

v ITA-8100 / ITA-8120 User Manual
16. ATTENTION: Risque d’explosion si la batterie est remplacee de maniere incor-
recte. Remplacer uniquement avec un modèle recommandé par le fabricant, et
éliminer les piles usagées selon les instructions du fabricant.
17. ATTENTION: Pour éviter tout risque d'electrocution, cet équipement ne doit
être branché qu'au réseau d'alimentation avec une terre de protection.
Conformément à la norme CEI 704-1:1982, l’opérateur ne doit pas expérimenter un
niveau sonore supérieur à 70 dB (A).
AVERTISSEMENT: Ces consignes suivent la norme CEI 704-1.
Advantech décline toute responsabilité concernant l'exactitude des déclarations con-
tenues dans ce document.
Declaration of Conformity
This equipment has been tested and found to comply with the limits for a Class A dig-
ital device, pursuant to part 15 of the FCC Rules. These limits are designed to pro-
vide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Opera-
tion of this equipment in a residential area is likely to cause harmful interference. In
such cases, users are required to correct the interference at their own expense.
RTC Battery Information
The computer features a battery-powered real-time clock circuit. The battery is at risk
of exploding if incorrectly replaced. Replace only with same type recommended by
the manufacturer or an equivalent. Discard used batteries according to the manufac-
turer's instructions.
Disposal of a battery into fire or a hot oven, or by mechanically crushing or cutting the
battery, can result in an explosion.
Risque d’explosion si la batterie est remplacee de maniere incorrecte. Remplacer
uniquement avec un modèle recommandé par le fabricant, et éliminer les piles
usagées selon les instructions du fabricant.
Éliminer une batterie dans un feu ou un four chaud, ou écraser ou couper
mécaniquement une batterie peut provoquer une explosion. Veillez à connecter le
cordon d'alimentation à une prise de courant avec mise à la terre.

ITA-8100 / ITA-8120 User Manual vi
Warnings, Cautions, and Notes
Warning! Warnings indicate conditions that may cause personal injury!
Les avertissements indiquent des conditions qui, si elles ne sont pas
observées, peuvent causer des dommages personnels (blessures).
Caution! Cautions are included to help prevent hardware damage and data
losses. For example, “The battery is at risk of exploding if incorrectly
installed. Do not attempt to recharge, force open, or heat the battery.
Replace the battery only with the same type recommended by the man-
ufacturer or an equivalent. Discard used batteries according to the man-
ufacturer's instructions.”
Des précautions sont incluses pour vous aider à éviter d'endommager le
matériel ou de perdre des données. Par exemple, “Il y a un risque
d'explosion d'une nouvelle batterie, si celle-ci est mal installée.
N'essayez pas de recharger, d'ouvrir de force ou de chauffer la batterie.
Remplacez la batterie exclusivement par le même type ou par un type
équivalent recommandé par le fabricant. Jeter les batteries usagées
conformément aux instructions du fabricant.”
Note! Notes provide additional optional information.

vii ITA-8100 / ITA-8120 User Manual
Contents
Chapter 1 General Information ............................1
1.1 Introduction ............................................................................................... 2
1.2 Specifications............................................................................................ 2
1.2.1 System Kernel............................................................................... 2
1.2.2 I/O Ports........................................................................................ 2
1.2.3 LCD............................................................................................... 2
1.3 System Power ........................................................................................... 3
1.4 Safety and Environment............................................................................ 3
1.4.1 Safety............................................................................................ 3
1.4.2 Environment.................................................................................. 3
1.5 Panel and Cutout Dimensions................................................................... 4
Figure 1.1 ITA-8100 Series Dimensions Diagram ....................... 4
Figure 1.2 ITA-8120 Series Dimensions Diagram ....................... 5
Chapter 2 Connectors and Function Keys .........7
2.1 Introduction ............................................................................................... 8
2.2 I/O Connectors.......................................................................................... 8
2.3 Bezel Key Mapping ................................................................................. 10
Chapter 3 Firmware and BIOS Information.......13
3.1 DIO Setting Steps ................................................................................... 14
3.2 Light Sensor Enabled and Disabled........................................................ 15
3.2.1 Introduction ................................................................................. 15
3.2.2 Disable/Enable Light Sensor....................................................... 16
3.3 Watchdog Sample Code ......................................................................... 18
Appendix A Panel Mounting..................................21
A.1 Panel Mounting ....................................................................................... 22
Appendix B DC Power Connection.......................23
B.1 DC Power Connection............................................................................. 24
B.2 Connexion Pour Source D'alimentation .................................................. 25

ITA-8100 / ITA-8120 User Manual viii

Chapter 1
1General Information
Introduction
Specifications
System Power
Safety and Environment
Panel and Cutout Dimensions

ITA-8100 / ITA-8120 User Manual 2
1.1 Introduction
Advantech’s ITA-8100 / ITA-8120 series touch panel PC is a fanless human machine
interface (HMI) equipped with a 10.4-inch / 12.1-inch display with projective capaci-
tive touchscreen aimed at railway applications. The panel’s small flat design saves
space for easy installation in driver cabins. The configuration flexibly allows the sys-
tem to be adjusted for specific applications and train models. Designed to withstand
operation in harsh environments, ITA-8100 / ITA-8120 supports a wide operating
temperature range (-40 ~ 70 °C/-40 ~ 158 °F), and satisfies EN 50155 railway regula-
tions.
1.2 Specifications
1.2.1 System Kernel
CPU: Intel Atom® x7-E3950 quad-core processor @ 2.0 GHz
Memory: 1 x DDR3L SODIMM (4 GB default; supports up to 8 GB)
OS Support: Windows 10 / Linux
Storage: 1 x M.2 2242 SSD (64 GB default)
LED: 1 x Power LED
Cooling System: Fanless design
Dimensions (W x H x D):
ITA-8100 series: 310 x 214 x 70 mm (12.1 x 8.4 x 2.8 in)
ITA-8120 series: 350 x 260 x 71.5 mm (13.8 x 10.2 x 2.8 in)
1.2.2 I/O Ports
1 x Power connector (M12 A-coded, 4-pin male)
2 x LAN 100/1000 base (M12 X-coded, 8-pin female)
2 x RS-422/485 (M12 A-coded, 5-pin female)
1 x USB 2.0 (M12 A-coded, 4-pin female)
1 x Audio (M12 A-coded, 5-pin male)
1 x Digital I/O (M12 A-coded 8-pin female)
Optional: MVB, CAN, GSM-R, GPS, Wi-Fi, WWAN, RS-232, and more (please
contact for more information)

3 ITA-8100 / ITA-8120 User Manual
Chapter 1 General Information
1.2.3 LCD
ITA-8100
Display Type TFT LED LCD
Size (diagonal) 10.4"
Resolution (Pixels) 1024 x 768 max.
Luminance 500 nits
Contrast Ratio 1000:1
Backlight Adjustment Automatic with built-in light sensor / Manual
(Switched in BIOS)
ITA-8100B
Display Type TFT LED LCD
Size (diagonal) 10.4"
Resolution (Pixels) 1024 x 768 max.
Luminance 1300 nits
Contrast Ratio 700:1
Backlight Adjustment Automatic with built-in light sensor / Manual
(Switched in BIOS)
ITA-8120
Display Type TFT LED LCD
Size (diagonal) 12.1"
Resolution (Pixels) 1024 x 768 max.
Luminance 600 nits
Contrast Ratio 1000:1
Backlight Adjustment Automatic with built-in light sensor / Manual
(Switched in BIOS)
Note! The LCD may have several unusually bright or dark pixels. This phe-
nomenon is commonplace in today’s LCD manufacturing.

ITA-8100 / ITA-8120 User Manual 4
1.3 System Power
Power Consumption:
ITA-8100: 30W
ITA-8100B: 35W
ITA-8120: 35W
Input Voltage: 24VDC, 48VDC, 72VDC, 110VDC (±40%)
1.4 Safety and Environment
1.4.1 Safety
FCC class A
CE
UL 62368
EN 50155:2017
IP65 rating (front panel)
1.4.2 Environment
Operating Temperature: -40 ~ 70 °C/-40 ~ 158 °F (85 °C/185 °F for 10 min-
utes)
Storage Temperature: -40 ~ 70 °C/-40 ~ 158 °F
Humidity: 93% @ 40 °C (non-condensing)
Shock and Vibration: IEC 61373

5 ITA-8100 / ITA-8120 User Manual
Chapter 1 General Information
1.5 Panel and Cutout Dimensions
 ITA-8100
Figure 1.1 ITA-8100 Series Dimensions Diagram
310 [12.205]
85 [3.346]85 [3.346]
214 [8.425]
295.65 [11.640]
85 [3.346] 85 [3.346]
6-Hole Ø6.5 [Ø0.256]
10 [0.394]
70 [2.756]
Unit: mm[inch]
267 [10.512]
186.06 [7.325]
14.33 [0.564]
92.7 [3.650]
Ø6.5 [Ø0.256]
85 [3.346]85 [3.346]
295.65 [11.640]
Panel Cutout
70 [2.756]
92.5 [3.642]
97.6 [3.843]

ITA-8100 / ITA-8120 User Manual 6
 ITA-8120
Figure 1.2 ITA-8120 Series Dimensions Diagram
108.4 [4.268]108.4 [4.268]
260 [10.236]
335.7 [13.215]
350 [13.780]
108.4 [4.268]108.4 [4.268]
10 [0.394]
71.5 [2.815]
Unit: mm[ inch]
247 [9.724]
125.1 [4.925] 125.1 [4.925]
11.8 [0.466]
6- Hol e 6.5 [ 0.256]
335.7 [13.215]
108.4 [4.268]108.4 [4.268] 108.4 [4.268]108.4 [4.268]
Panel Cutout
71.5 [2.815]
99.1 [3.902]
94 [3.701]
6- Hol e 6.5 [ 0. 256]

Chapter 2
2Connectors and
Function Keys
Introduction
I/O Connectors
Bezel Key Mapping

ITA-8100 / ITA-8120 User Manual 8
2.1 Introduction
The following sections show the pin assignments for the I/O connectors and bezel
key mapping to facilitate application integration.
2.2 I/O Connectors
COM (RS-422/485) Pin Number Definition Female
M12-A-5P-F
1 485-422_TX-
2 485-422_TX+
3 422_RX+
4 422_RX-
5 GND
USB Pin Number Definition Female
M12-A-4P-F
1 D-
2 +5V
3 D+
4 GND
DIO
USB
AUDIOLANCOM POWER

9 ITA-8100 / ITA-8120 User Manual
Chapter 2 Connectors and Function Keys
DIO Pin Number Definition Female
M12-A-8P-F
1 Vcc
2 DI0
3 DI1
4 DI2
5 DI3
6 DI4
7 DO0
8 GND
LAN Pin Number Definition Female
M12-X-8P-F
1 LAN_MDI0+
2 LAN_MDI0-
3 LAN_MDI1+
4 LAN_MDI1-
5 LAN_MDI3+
6 LAN_MDI3-
7 LAN_MDI2-
8 LAN_MDI2+
AUDIO Pin Number Definition Male
M12-A-5P-M
1 Line Out_R
2 Line Out_L
3 MIC_R
4 MIC_L
5 Audio_GND
POWER Pin Number Definition Male
M12-A-4P-M
1 V-
2 V+
3 V+
4 V-

ITA-8100 / ITA-8120 User Manual 10
2.3 Bezel Key Mapping
Image Key Image Key
K1 Backlight on/
off; Reboot* K17 ESC
K2 SHIFT F2 K18 LEFT
K3 SHIFT F3 K19 RIGHT
K4 SHIFT F4 K20 UP
K5 SHIFT F5 K21 DOWN
K6 SHIFT F6 K22 ENTER
K7 SHIFT F7 K23 1
K8 SHIFT F8 K24 2
K9 SHIFT F9 K25 3
K10 SHIFT F10 K26 4

11 ITA-8100 / ITA-8120 User Manual
Chapter 2 Connectors and Function Keys
*Press the power button (K1) for less than 1 second: Backlight on/off
*Press and hold the power button (K1) for 5 seconds: System reboot
K11 F1 K27 5
K12 F2 K28 6
K13 F3 K29 7
K14 F4 K30 8
K15 F5 K31 9
K16 F6 K32 0

ITA-8100 / ITA-8120 User Manual 12