Advantech IPPC-7158 Series User manual

IPPC-7158 Series
15" XGA TFT LCD Industrial
Panel PC with 14 x ISA/PCI/
PICMG Slots, Passive Backplane
and Membrane Keypad
User Manual

IPPC-7158 User Manual ii
Copyright Notice
This document is copyrighted 2008, by Advantech Co. Ltd. All rights are
reserved. Advantech Co., Ltd. reserves the right to alter the products
described in this manual at any time without notice. No part of this man-
ual may be reproduced, copied, translated or transmitted in any form or
by any means without the prior written permission of Advantech. Infor-
mation provided in this manual is intended to be accurate and reliable.
However, Advantech assumes no responsibility for use of this manual,
nor for any infringements upon the rights of third parties which may
result from such use. All brand and product names mentioned herein are
trademarks or registered trademarks of their respective holders.
Acknowledgments
IBM and PC are trademarks of International Business Machines Corpora-
tion.
For more information on this and other Advantech products, please visit
our website at: http://www.advantech.com
For technical support and service, please visit our support website at:
http://www.advantech.com.tw/support/
Part No. 2003715800 1st Edition
Printed in Taiwan October 2008

iii
FCC Class A
Note: This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environ-
ment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Opera-
tion of this equipment in a residential area is likely to cause harmful inter-
ference in which case the user will be required to correct the interference
at his own expense.
Warning! Any changes or modifications made to the
equipment which are not expressly approved by
the relevant standards authority could void your
authority to operate the equipment.

IPPC-7158 User Manual iv
Packing List
Before setting up the system, check that the item is among those listed
below and is in good condition. If your Workstation does not match any
of those below, please contact your dealer immediately.
• CD ROM for IPPC Series
• Registration and 2 year Warranty card
• SATA Cable x 2
• SATA Power Cable x 2
• PATA 40 PIN DMA66 Flat Cable
• FDD cable
• D-Sub Flat Cable with bracket
• FAN power cable
• Simplified Chinese Manual
• China RoHs for IPPC-7000 series
• Jumper Bag(mini jumper*20)
IPPC-7158 Industrial Workstations includes the following models:
IPPC-7158B-X1AE: 15" XGA TFT LCD Passive Backplane Industrial
Panel PC with 14 x ISA/PCI/PICMG Slots and Membrane Keypad
IPPC-7158B-R1AE: 15" XGA TFT LCD Passive Backplane Industrial
Panel PC with 14 x ISA/PCI/PICMG Slots and Membrane Keypad and
resistive touchscreen

v
Additional Information and Assistance
Step 1. Visit the Advantech web site at www.advantech.com where you
can find the latest information about the product.
Step 2. Contact your distributor, sales representative, or Advantech's cus-
tomer service center for technical support if you need additional
assistance. Please have the following information ready before
you call:
• Product name and serial number
• Description of your peripheral attachments
• Description of your software (operating system, version, application
software, etc.)
• A complete description of the problem
• The exact wording of any error messages

IPPC-7158 User Manual vi
Safety Instructions
1. Read these safety instructions carefully.
2. Keep this User's Manual for later reference.
3. Disconnect this equipment from any AC outlet before cleaning. Use a damp
cloth. Do not use liquid or spray detergents for cleaning.
4. For plug-in equipment, the power outlet socket must be located near the
equipment and must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or let-
ting it fall may cause damage.
7. The openings on the enclosure are for air convection. Protect the equipment
from overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.
9. Position the power cord so that people cannot step on it. Do not place anything
over the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the power
source to avoid damage by transient overvoltage.
12. Never pour any liquid into an opening. This may cause fire or electrical shock.
13. Never open the equipment. For safety reasons, the equipment should be
opened only by qualified service personnel.
14. If one of the following situations arises, get the equipment checked by service
personnel:
a. The power cord or plug is damaged.
b. Liquid has penetrated into the equipment.
c. The equipment has been exposed to moisture.
d. The equipment does not work well, or you cannot get it to work according
to the user's manual.
e. The equipment has been dropped and damaged.
f. The equipment has obvious signs of breakage.
15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE
THE STORAGE TEMPERATURE MAY GO BELOW -20° C (-4° F) OR
ABOVE 60° C (140° F). THIS COULD DAMAGE THE EQUIPMENT. THE
EQUIPMENT SHOULD BE IN A CONTROLLED ENVIRONMENT.
16. CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY
REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT
TYPE RECOMMENDED BY THE MANUFACTURER, DISCARD USED
BATTERIES ACCORDING TO THE MANUFACTURER'S INSTRUC-
TIONS.
The sound pressure level at the operator's position according to IEC 704-1:1982 is
no more than 70 dB (A).
DISCLAIMER: This set of instructions is given according to IEC 704-1. Advan-
tech disclaims all responsibility for the accuracy of any statements contained
herein.

vii
Contents
Chapter 1 General Information ....................................... 2
1.1 Introduction ....................................................................... 2
1.2 Specifications .................................................................... 3
1.2.1 General ........................................................................... 3
1.2.2 System Hardware ........................................................... 3
1.2.3 LCD Display .................................................................. 4
1.2.4 Touchscreen (Optional) ................................................. 4
1.2.5 Environment ................................................................... 4
1.3 Dimensions........................................................................ 5
Chapter 2 System Setup.................................................... 8
2.1 A Quick Tour of IPPC-7158 ............................................. 8
Figure 2.1:Open View .................................................... 9
Figure 2.2:Side View ..................................................... 9
2.1.1 USB Ports .................................................................... 10
Figure 2.3:Opening the Front USB Port Cover ........... 10
2.1.2 Adjusting the LCD Brightness ..................................... 10
2.2 Installing Optional Disk Drives....................................... 12
2.3 Rack Mounting................................................................ 12
Chapter 3 Touchscreen ................................................... 14
3.1 Introduction ..................................................................... 14
3.2 Touchscreen Driver Installation & Configuration .......... 14
Appendix A LCD Specifications........................................ 16
A.1 IPPC-7158 LCD Specifications ...................................... 16
Appendix B Pin Assignments ............................................ 18
B.1 Connector Pin Definitions............................................... 19
B.2 PCI Routing Table........................................................... 22
Appendix C Keyboard Translator .................................... 24
C.1 Overview ......................................................................... 24
C.2 Programming the Front Panel Macro Keys..................... 25

IPPC-7158 User Manual viii

CHAPTER
1
General Information
This chapter gives background
information on the IPPC-7158 series
Sections include:
• Introduction
• Specifications
• Dimensions

IPPC-7158 User Manual 2
Chapter 1 General Information
1.1 Introduction
The IPPC-7158 features a 15" TFT LCD and 14 expansion slots for PCI,
PICMG and ISAand an ATX industrial backplane to support CPU cards.
The IPPC-7158 also provides many powerful features such as detahable
front panel, front-accessible USB port, 53 membrane key & touch pad
with two mouse buttons, 6 OSD control keys, NEMA4/IP65 compliant
front panel, and optional analog resistive touchscreen (USB Interface).
Modularized Side-Open Front Panel Makes Maintenance Easy
The IPPC-7158 makes user can maintain the system fast and easily. First,
if there are problems with the LCD display, the detachable front panel
allows you to replace or service it simply and quickly. This helps saves
downtime costs associated with system crashes. Secondly, the side-open
LCD front panel also make it more convenient when you want to main-
tain the CPU, I/O cards, HDD, CD-ROM and even floppy.
Industrial Design Withstands Harsh Environments
In addition, the IPPC-7158 also features many powerful functions tomeet
the industrial-grade requirements. The front panel is made of Aluminum
and being chemical treated by anode. That prevents the panelfrom dam-
aging by acid and salt. Besides, it's waterproof and IP65/NEMA4 compli-
ant. The IPPC-7158 also offers the stainless steel chassis. It also protects
the chassis. For keeping the system working properly, the IPPC-7158 pro-
vides a fan & filter to avoid overheating & dust. In addition, the IPPC-
7158 also provides three mounting ways to fit different application: 19"
rack, panel or wall mounting.

3 Chapter1
1.2 Specifications
1.2.1 General
• Button Control:
Membrane Keypad 1: 43 operating keys
Membrane Keypad 2: 10 programmable macro function keys
• Certifications: BSMI, CCC, CE, FCC
• Cooling System: 1 x 49 CFM fan w/50,000 hrs MTBF
• Dimensions (W x H x D):
482 x 354.8 x 162 mm (18.97" x 13.96" x 6.37")
• Disk Drive Bay:
Supports 1 x FDD, 1 x 3.5" HDD and 1 X CD-ROM (both optional)
• Enclosure: Front Panel – Aluminum,
Chassis – Anti-rust
• Mounting: Panel, 19” Rack
• Power Input: 100-240Vac, 10A, 10~50Hz
• Power Ouput: + 5V@30A, +12V@15A, +3.3V@28A, [email protected],
[email protected]A, +5 VSB@2A
• Power Supply: Watt :300 W, MTBF: 100,000 hrs
• Weight (Gross): 18 kg ( 39.7 lb)
1.2.2 System Hardware
• 2 x PICMG
• 10 x PCI
• 2 x ISA

IPPC-7158 User Manual 4
1.2.3 LCD Display
• Backlight Life: 60,000 hrs
• Contrast Ratio: 500 : 1
• Display Size: 15"
• Display Type: XGA TFT LCD
• Luminance: 250 cd/m2
• Max. Colors: 16.2 M (RGB 6-bit + FRC data)
• Max. Resolution: 1024x768
• OSD Control: ON/OFF, Brightness down, up (behind the front panel)
• Viewing Angle (H/V°): 140/120
1.2.4 Touchscreen (Optional)
• Interface: USB
• Lifespan:
10 million with silicone rubber of R8 finger, writing rate is 250g at 2X/s
• Light Transmission: > 80% (AMT)
• OS Support: Windows 95/98/ME/2000/XP/CE/NT/Vista, Linux
• Type: 8W Resistive
1.2.5 Environment
• Humidity: 5 ~ 85% RH @ 40° C (non-condensing)
• Ingress Protection: Front panel NEMA4/IP65
• Operating Temperature: 0 ~ 50° C (32 ~ 122° F)
• Storage Temperature: -20 ~ 60° C (-4 ~ 140° F)
• Vibration Protection: 5~500 Hz,
1 GRMS random vibration (operating)

5 Chapter1
1.3 Dimensions
Figure 1.1: IPPC-7158 Dimensions
17”
F12F11F10F1
M1
Enter
RightLeft
SpaceShiftAltCtrl
Space
Back
Tab PgDn
PgUpDeleteEsc
_
+0=
/
_
_ _
6
3
5
2
1
4
987789
_ _
_
Esc Delete PgUp
PgDn
Tab
Back
Space
Ctrl Alt Shift Space
Left Right
Enter
M2
M3
M4
M5
M6
M7
M8
M9
M10
F2 F3 F4 F5 F6 F7 F8 F9 F11 F 12
IPPC-7158A

IPPC-7158 User Manual 6

CHAPTER
2
System Setup
This chapter details system setup for
the IPPC-7158 Series.
Sections include:
• A Quick Tour of IPPC-7158
• Installing a CPU & CPU Cooler
• Installing Optional Disk Drives
• Rack Mounting

IPPC-7158 User Manual 8
Chapter 2 System Setup
2.1 A Quick Tour of IPPC-7158
Before you start the computer, please follow these procedures to set up
the system.
1. Check and adjust jumpers on motherboard (optional by each CPU card)
2. Install SDRAM
3. Install CPU & CPU Cooler
4. Install add-on cards
5. Connect the wires, cables and accessories
6. Mount the computer
7. Program the BIOS settings
8. Install an operating system.
Warnings 1. The IPPC-7158B only includes the chassis and
B/P. One could use compatible CPU card to install
the system, each jumper setting and CPU chosen
based on it's own specification.
2. Switch off and unplug the computer every time
you access its interior.
3. The motherboard inside the system is composed
of many delicate ICs, chips and other integrated
circuit components. These components are easily
damaged by static shock. When you begin to install
components, please:
- Avoid touching metal parts of the motherboard.
- Wear an anti-static ring when handling a CPU or
SDRAM module.
- Put SDRAM modules and the CPU inside an
anti-static bag before installation.
4. Refer to each CPU card for BIOS setting details.
5. This machine doesn’t support USB wake func-
tion during standby mode on Windows 2000.

9 Chapter2
Figure 2.1: Open View
Figure 2.2: Side View

IPPC-7158 User Manual 10
2.1.1 USB Ports
An external USB device may be connected to the system via the USB
ports located on the right side of the system unit and also could access
from 1 USB port on the front panel of IPPC-7158.
1. Connect the external device to the system.
2. The USB ports support hot plug-in connection. You should install
the device driver before you use the device.
Figure 2.3: Opening the Front USB Port Cover
2.1.2 Adjusting the LCD Brightness
The LCD OSD control key is located behind the front panel module, you
have to open the front panel to access it.
1. Unscrew the 2 screws on the right side of front panel.
2. Open the front panel door, to find the LCD OSD control key.

11 Chapter2
2.1.3 System On/Off
The IPPC-7158 has 1 system on/off switch, located inside the chassis.

IPPC-7158 User Manual 12
2.2 Installing Optional Disk Drives
The IPPC-7158 provides spaces for one 3.5" hard disk drives, one CD-
ROM drive, & one 3.5" floppy disk drive within the chassis. Front-facing
FDD & CD-ROM have already been installed. You can access them after
opening the front LCD panel.
Below is the procedure of installing HDD and CD-ROM:
1. Unscrew the 3 screws and 4 screws on the side of the case to
remove the HDD Drive Bay
2. Unscrew the 4 Screws on the bottom of the drive bay to separate
the 2 parts.
3. Install HDD with 2 screws on each side.
4. Combine the 2 sheet metal parts of the drive bay with the screws
5. Installed the HDD drive bay finished (with CD-ROM).
2.3 Rack Mounting
The IPPC-7158B can be mounted to a 19" industrial rack.