Advantech TPC-1550H User manual

User Manual
TPC-1550H/1551H
Industrial Touch Panel
Computers with Intel®Atom™
Processors

TPC-1550H/1551H User Manual ii
Copyright
The documentation and the software included with this product are copyrighted 2011
by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right
to make improvements in the products described in this manual at any time without
notice. No part of this manual may be reproduced, copied, translated or transmitted
in any form or by any means without the prior written permission of Advantech Co.,
Ltd. Information provided in this manual is intended to be accurate and reliable. How-
ever, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringe-
ments of the rights of third parties, which may result from its use.
Acknowledgements
Intel and Pentium are trademarks of Intel Corporation.
Microsoft Windows and MS-DOS are registered trademarks of Microsoft Corp.
All other product names or trademarks are properties of their respective owners.
This Manual Covers the Following Models:
TPC-1550H
TPC-1551H
Part No. 2003155000 Edition 1
Printed in Taiwan December 2011

iii TPC-1550H/1551H User Manual
Product Warranty (2 years)
Advantech warrants to you, the original purchaser, that each of its products will be
free from defects in materials and workmanship for two years from the date of pur-
chase.
This warranty does not apply to any products which have been repaired or altered by
persons other than repair personnel authorized by Advantech, or which have been
subject to misuse, abuse, accident or improper installation. Advantech assumes no
liability under the terms of this warranty as a consequence of such events.
Because of Advantech’s high quality-control standards and rigorous testing, most of
our customers never need to use our repair service. If an Advantech product is defec-
tive, it will be repaired or replaced at no charge during the warranty period. For out-
of-warranty repairs, you will be billed according to the cost of replacement materials,
service time and freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For example, CPU
speed, Advantech products used, other hardware and software used, etc.) Note
anything abnormal and list any onscreen messages you get when the problem
occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return merchandize
authorization) number from your dealer. This allows us to process your return
more quickly.
4. Carefully pack the defective product, a fully-completed Repair and Replacement
Order Card and a photocopy proof of purchase date (such as your sales receipt)
in a shippable container. A product returned without proof of the purchase date
is not eligible for warranty service.
5. Write the RMA number visibly on the outside of the package and ship it prepaid
to your dealer.

TPC-1550H/1551H User Manual iv
Declaration of Conformity
CE
This product has passed the CE test for environmental specifications when shielded
cables are used for external wiring. We recommend the use of shielded cables. This
kind of cable is available from Advantech. Please contact your local supplier for
ordering information.
FCC Class A
Note: This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Opera-
tion of this equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own expense.
Technical Support and Assistance
1. Visit the Advantech web site at http://support.advantech.com where you can find
the latest information about the product.
2. Contact your distributor, sales representative, or Advantech's customer service
center for technical support if you need additional assistance. Please have the
following information ready before you call:
–Product name and serial number
–Description of your peripheral attachments
–Description of your software (operating system, version, application software,
etc.)
–A complete description of the problem
–The exact wording of any error messages

v TPC-1550H/1551H User Manual
Safety Instructions
1. Read these safety instructions carefully.
2. Keep this User Manual for later reference.
3. Disconnect this equipment from any AC outlet before cleaning. Use a damp
cloth. Do not use liquid or spray detergents for cleaning.
4. For plug-in equipment, the power outlet socket must be located near the equip-
ment and must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or letting
it fall may cause damage.
7. The openings on the enclosure are for air convection. Protect the equipment
from overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.
9. Position the power cord so that people cannot step on it. Do not place anything
over the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the power source
to avoid damage by transient overvoltage.
12. Never pour any liquid into an opening. This may cause fire or electrical shock.
13. Never open the equipment. For safety reasons, the equipment should be
opened only by qualified service personnel.
14. If one of the following situations arises, get the equipment checked by service
personnel:
The power cord or plug is damaged.
Liquid has penetrated into the equipment.
The equipment has been exposed to moisture.
The equipment does not work well, or you cannot get it to work according to
the user's manual.
The equipment has been dropped and damaged.
The equipment has obvious signs of breakage.
15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE
STORAGE TEMPERATURE MAY GO BELOW -20° C (-4° F) OR ABOVE 60° C
(140° F). THIS COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT
SHOULD BE IN A CONTROLLED ENVIRONMENT.
16. CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY
REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE
RECOMMENDED BY THE MANUFACTURER, DISCARD USED BATTERIES
ACCORDING TO THE MANUFACTURER'S INSTRUCTIONS.
The sound pressure level at the operator's position according to IEC 704-1:1982 is
no more than 70 dB (A).
DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech
disclaims all responsibility for the accuracy of any statements contained herein.
Caution! Danger of explosion if battery is incorrectly replaced. Replace only with
the same or equivalent type recommended by the manufacturer. Dis-
pose of used batteries according to the manufacturer's instructions.

TPC-1550H/1551H User Manual vi

vii TPC-1550H/1551H User Manual
Chapter 1 General Information ............................1
1.1 Introduction ............................................................................................... 2
1.2 Specifications ............................................................................................ 2
1.2.1 System Kernel............................................................................... 2
1.2.2 I/O Ports........................................................................................ 2
1.2.3 Safety and Environment................................................................ 3
1.3 LCD Specifications.................................................................................... 3
1.4 Touchscreen Specifications ...................................................................... 3
1.5 Power ........................................................................................................ 4
1.6 I/O Ports Arrangement .............................................................................. 4
Figure 1.1 TPC-155OH - I/O Port Arrangement .......................... 4
Figure 1.2 TPC-1551H - I/O Port Arrangement ........................... 4
1.7 Panel Mounting ......................................................................................... 5
Figure 1.3 Panel Mounting........................................................... 5
1.8 Dimensions and Cutout............................................................................. 5
Figure 1.4 TPC-1550H Dimensions............................................. 6
Figure 1.5 TPC-1551H Dimensions............................................. 7
Chapter 2 System Setup.......................................9
2.1 System Setup.......................................................................................... 10
Figure 2.1 Unpack the Package ................................................ 10
Figure 2.2 Install CompactFlash Memory Card ......................... 11
Figure 2.3 Power Connector and Power Lines .......................... 11
Figure 2.4 Power Receptor & Button Pin Assignment ............... 12
2.1.1 Installing the Drivers ................................................................... 12
Chapter 3 Features in Windows XP Embedded15
3.1 Features in Windows XP Embedded ...................................................... 16
3.2 EWF ........................................................................................................ 16
3.3 HORM ..................................................................................................... 16
Appendix A Serial Port Settings ...........................17
A.1 Jumper Settings & Connector List........................................................... 18
A.2 Pin Assignment ....................................................................................... 18
A.3 RS-485 / RS-422 Setting......................................................................... 19

TPC-1550H/1551H User Manual viii

Chapter 1
1General Information

TPC-1550H/1551H User Manual 2
1.1 Introduction
The TPC-1550H and TPC-1551H Touch Panel Computers are state-of-the-art
Human Machine Interfaces featuring 15" displays with Intel Atom eMenlow XL pro-
cessors and the following key features:
Fanless
By using a low-power processor, the system does not have to rely on fans,
which often are unreliable and causes dust to circulate inside the equipment.
Bright Display
The TFT LCD display suits industrial demands for clear interfaces. Wide Oper-
ating Temperature & Isolation Protection (TPC-1551H Only) These products
provide a -20 ~ 60° C wide operating temperature solution and complete isola-
tion 2KV protection for their serial ports.
Windows CE Support
In addition to the OS support of Windows XP, Advantech offers platform support
for Windows CE and Windows XP embedded. The optional Windows CE oper-
ating system specifically for Industrial Touch Panel Computers is also available.
Energy Star Approval
1.2 Specifications
1.2.1 System Kernel
CPU: Intel® Atom™ N270H 1.6GHz (1550H) Z520 1.33GHz (1551H)
BIOS: Award 4 Mbit flash BIOS
System Chipset: 945GSE + ICH7M (1550H)
eMenlow XL + Poulsbo (1551H)
VGA: Integrated in 945GSE (1550H) eMenlow XL (1551H)
Ethernet: 10/100/1000Base-T
Watchdog Timer:
–TPC-1550H: W83627DHG watchdog timmer; 1.6 second timeout period
–TPC-1551H: SCH3114X1 watchdog timer; 1.6 second timeout period
Storage: CompactFlash® slot or SATA HDD x 1 (TPC-1550H only CF for
storage)
1.2.2 I/O Ports
TPC-1550H:
2 serial ports: RS-232 x 2 (w/o isolation)
1 RJ-45 Ethernet port
2 USB 2.0 Ports: compliant with USB 1.0 and 1.1. (Host)
TPC-1551H:
2 serial ports: RS-232 x 1 (w/ isolation), RS-422/485 x 1 (w/ isolation)
2 RJ-45 Ethernet port
2 USB 2.0 Ports: compliant with USB 1.0 and 1.1. (Host)

3 TPC-1550H/1551H User Manual
Chapter 1 General Information
1.2.3 Safety and Environment
Safety
FCC Class A
CE certificated
The front bezel is compliant with NEMA 4 and IP65
Environment
Operating Temperature:
–0 ~ 45° C (32 ~ 113° F) TPC-1550H
–-20 ~ 60° C (-4 ~ 140° F) TPC-1551H
Storage Temperature:
–-20 ~ 60° C (-4 ~ 140° F) TPC-1550H
–-30 ~ 80° C (-22 ~ 176° F) TPC-1551H
Humidity: 40° C @ 10~95% relative humidity (non-condensing)
Vibration: 2 grms (5 ~ 500 Hz) with CF Card, 1 grm with HDD kit (1551H)
1.3 LCD Specifications
1.4 Touchscreen Specifications
Touch Type: Resistive
Base Glass Construction: Tempered glass
Resolution: 1024 x 1024
Light Transmission: 80% ± 3% (Measured by BYK-Gardner)
Controller: USB Interface (1550H), RS-232 Interface (1551H)
Lifespan: 1 million touches at single point
TPC-1550H / TPC-1551H
Display Type TFT LCD
Size (diagonal) 15°
Maximum Resolution 1024 x 768 (XGA)
Maximum Colors 262K
Viewing Angle 160°/140°
Luminance (cd / m2) 350
Contrast Ratio 700:1
Operating Temperature -30 ~ 85° C
Backlight LED
Note! There might be several bright or dark pixels on the LCD. This phenome-
non is normal in today’s LCD manufacturing.

TPC-1550H/1551H User Manual 4
1.5 Power
Input Voltage: 18 - 28 VDC (the fuse will become an open circuit if the input
level exceeds 29 VDC) 1550H
Input Voltage: 18 - 32 VDC (the fuse will become an open circuit if the input
level exceeds 33 VDC) 1551H
Typical: 24 VDC @ 1.54 Amp (1550H) 24 VDC @ 1.33 Amp (1551H)
1.6 I/O Ports Arrangement
The arrangement of the I/O ports is shown in in Figure 1.1 and 1.2.
Figure 1.1 TPC-155OH - I/O Port Arrangement
Figure 1.2 TPC-1551H - I/O Port Arrangement
Note! Touchscreen ITO maybe crash duo to heavy usage .

5 TPC-1550H/1551H User Manual
Chapter 1 General Information
1.7 Panel Mounting
1. There is an adhesive waterproof gasket on the AL front bezel. Make sure the
waterproof gasket is in position before installing TPC into the panel opening.
1. Install the TPC into the panel opening.
2. Find the eight clampers and eight long screws in the accessory pack. Hook the
clampers to the holes around the four sides of the bezel. Insert the screws into
every clamper and fasten them. These screws will push the mounting panel and
fix the unit.
3. The suggested mounting panel thickness is less than 6 mm (0.236”).
Figure 1.3 Panel Mounting
1.8 Dimensions and Cutout
Weight: 3 kg
Dimensions (W x H x D): 383 x 307 x 58.1 mm (15.08" x 12.09" x 2.29")
Cutout: 374.5 x 298.5 mm

TPC-1550H/1551H User Manual 6
Figure 1.4 TPC-1550H Dimensions
307
230.1
383
306.1 4.5
24.7
57.6
76.3140
7 4
115 115
7
4
189.25
373
297
236.0

7 TPC-1550H/1551H User Manual
Chapter 1 General Information
Figure 1.5 TPC-1551H Dimensions
383.0
307.0
306.1
230.1
24.70
4.5
58.5
76.4
140
236.0
7 4
189.25
373.0
297.0
115 115
7
4

TPC-1550H/1551H User Manual 8

Chapter 2
2System Setup

TPC-1550H/1551H User Manual 10
2.1 System Setup
You can easily get TPC started by following the below steps.
1. Unpack the TPC package. Check the packing list at the beginning of this manual
to make sure all items have been included.
Figure 2.1 Unpack the Package

11 TPC-1550H/1551H User Manual
Chapter 2 System Setup
2. Install a CompactFlash®card containing Windows CE, Embedded Windows XP
or another operating system.
Figure 2.2 Install CompactFlash Memory Card
3. Connect the power connector to the 24 VDC power lines. The power lines can
either be of some power adapter or in-house power source.
Figure 2.3 Power Connector and Power Lines
Warning! It is suggested to turn OFF system power as you plug in or pull out the
memory card, even though the CompactFlash memory is hot swappa-
ble.

TPC-1550H/1551H User Manual 12
Figure 2.4 Power Receptor & Button Pin Assignment
4. Plug the power lines into the system power receptor.
5. Push the power button to power on the system (figure 2.4).
6. Calibrate the touchscreen (click "PM" in the bottom corner).
2.1.1 Installing the Drivers
After installing your system software, you will be able to set up the Ethernet, VGA,
and touchscreen functions. All drivers are stored in a CDROM disc entitled “TPC-
1550H or TPC-1551H” which can be found in your accessory box.
The various drivers in the CD-ROM disc have their own text files which help users
install the drivers and understand their functions. These files are a very useful sup-
plement to the information in this manual.
Note! If you want to install the touchscreen driver & use the touchscreen utility,
please refer the user manual which is "PenMount 6000 Installation-
Guide" in the CD-ROM.
Note! The drivers and utilities used for the TPC-1550H and TPC-1551H panel
PCs are subject to change without notice. If in doubt, check Advantech's
website or contact our application engineers for the latest information
regarding drivers and utilities.