AEG AGV 15-125 XC User manual

Original instructions
Originalbetriebsanleitung
Notice originale
Istruzioni originali
Manual original
Manual original
Oorspronkelijke
gebruiksaanwijzing
Original brugsanvisning
Original bruksanvisning
Bruksanvisning i original
Alkuperäiset ohjeet

Orijinal iş
Pů


Eredeti használati utasítás
Izvirna navodila
Originalne pogonske upute
Instrukcijâm oriěinâlvalodâ
Originali instrukcija
Algupärane kasutusjuhend




Instrucţiuni de folosire originale




AGV 15-125 XC
AGV 15-125 XE
AGV 15-150 XC

Technical Data,Safety Instructions, Specied Conditions of Use,
Declaration of Conformity, Batteries, Maintenance, Symbols Please read and save these instructions!
English
1414
Technische Daten, Sicherheitshinweise, Bestimmungsgemäße Verwendung,
CE-Konformitätserklärung, Akkus, Wartung, Symbole Bitte lesen und aufbewahren!
Deutsch
1818
Caractéristiques techniques, Instructions de sécurité, Utilisation conforme aux
prescriptions, Déclaration CE de Conformité, Accus, Entretien, Symboles A lire et à conserver soigneusement
Français
2323
Dati tecnici,Norme di sicurezza,Utilizzo conforme, Dicharazione di Conformità CE,
Batterie, Manutenzione, Simboli Si prega di leggere e conservare le istruzioni!
Italiano
2828
Datos técnicos, Instrucciones de seguridad, Aplicación de acuerdo a la nalidad,
Declaracion de Conformidad CE, Bateria, Mantenimiento, Símbolos Lea y conserve estas instrucciones por favor!
Español
3333
Características técnicas, Instruções de segurança, Utilização autorizada,
Declaração de Conformidade CE, Acumulador, Manutenção, Symbole Por favor leia e conserve
em seu poder!
Português
3838
Technische gegevens, Veiligheidsadviezen, Voorgeschreven gebruik van het
systeem, EC-Konformiteitsverklaring, Akku, Onderhoud, Symbolen Lees en let goed op deze adviezen!
Nederlands
4343
Tekniske data, Sikkerhedshenvisninger, Tiltænkt formål,
CE-Konformitetserklæring, Batteri, Vedligeholdelse, Symboler Vær venlig at læse og Opbevare!
Dansk
4848
Tekniske data, Spesielle sikkerhetshenvisninger, Formålsmessig bruk,
CE-Samsvarserklæring, Batterier, Vedlikehold, Symboler Vennligst les og oppbevar!
Norsk
5353
Tekniska data, Säkerhetsutrustning, Använd maskinen Enligt anvisningarna,
CEFörsäkran, Batterier, Skötsel, Symboler Läs igenom och spara!
Svenska
5757
Tekniset arvot, Turvallisuusohjeet, Tarkoituksenmukainen käyttö,
Todistus CE-standardinmukaisuudesta, Akku, Huolto, Symbolit Lue ja säilytö!
Suomi
6161
Τεχνικά στοιχεία, Ειδικές υποδείξεις ασφάλειας, Χρήση σύμφωνα με το σκοπό
προορισμού, Δήλωση πιστότητας ΕΚ, Μπαταρίες, Χαρακτηριστικά, Συντήρηση, Σύμβολα.
Ελληνικά
6666
Teknik veriler, Güvenliğiniz için talimatlar, Kullanim, CE uygunluk beyanice,
Akü, Bakim, Semboller Lütfen okuyun ve saklayın
Türkçe
7171
Technická data, Speciální bezpečnostní upozornění, Oblast využití,
Ce-prohlášení o shodě, Akumulátory, Údržba, Symboly Po přečtení uschovejte
Česky
7676
Technické údaje, Špeciálne bezpčènostné pokyny, Použitie podl’a predpisov,
CE-Vyhlásenie konformity, Siet’ová prípojka, Údrzba, Symboly Prosím prečítať a uschovať!
Slovensky
8080
Dane techniczne,Specjalne zalecenia dotyczące bezpiecze´nstwa, Użytkowanie zgodne z
przeznaczeniem, Świadectwo zgodności ce, Podłączenie do sieci, Gwarancja, Symbole Należy uważnie przeczytać i
zachować do wglądu!
Polski
8585
Műszaki adatok, Különleges biztonsági tudnivalók, Rendeltetésszerű használat,
Ce-azonossági nyilatkozat, Hálózati csatlakoztatás, Karbantartás, Szimbólumok Olvassa el és őrizze meg
Magyar
9090
Tehnični podatki, Specialni varnostni napotki, Uporaba v skladu z namembnostjo,
Ce-izjava o konformnosti, Omrežni priključek, Vzdrževanje, Simboli Prosimo preberite in shranite!
Slovensko
9595
Tehnički podaci, Specijalne sigurnosne upute, Propisna upotreba,
CE-Izjava konformnosti, Priključak na mrežu, Održavanje, Simboli Molimo pročitati i sačuvati
Hrvatski
100100
Tehniskie dati, Speciālie drošības noteikumi, Noteikumiem atbilstošs izmantojums,
Atbilstība CE normām, Tīkla pieslēgums, Apkope, Simboli Pielikums lietošanas pamācībai
Latviski
104104
Techniniai duomenys, Ypatingos saugumo nuorodos, Naudojimas pagal paskirti,
CE Atitikties pareiškimas, Elektros tinklo jungtis, Techninis aptarnavimas, Simboliai Prašome perskaityti ir neišmesti!
Lietuviškai
109109
Tehnilised andmed, Spetsiaalsed turvajuhised, Kasutamine vastavalt otstarbele,
EÜ Vastavusavaldus, Võrku ühendamine, Hooldus, Sümbolid Palun lugege läbi ja hoidke alal!
Eesti
114114
Òåõíè÷åñêèå äàííûå, Ðåêîìåíäàöèè ïî òåõíèêå áåçîïàñíîñòè,
Èñïîëüçî- âàíèå, Ïîäêëþ÷åíèå ê ýëåêòðîñåòè, Îáñëóæèâàíèå, Ñèìâîëû
Пожалуйста прочтите и
сохраните эту инструкцию.
Pусский
118118
Òåõíè÷åñêè äàííè, Ñïåöèàëíè óêàçàíèÿ çà áåçîïàñíîñò, Èçïîëçâàíå ïî ïðåäíàçíà÷åíèå,
ÑÅ-Äåêëàðàöèÿ çà ñúîòâåòñòâèå, Ñâúðçâàíå êúì ìðåæàòà, Ïîääðúæêà, Ñèìâîëè
Моля прочетете и запазете!
Български
124124
Date tehnice, Instrucţiuni de securitate, Condiţii de utilizare specifcate,
Declaraţie de conformitate, Acumulatori, Intreţinere, Simboluri Va rugăm citiţi şi păstraţi aceste instrucţiuni
Română
129129
Òåõíè÷êè Ïîäàòîöè, Óïàòñòâî Çà Óïîòðåáà, Ñïåöèôèöèðàíè Óñëîâè Íà
Óïîòðåáà, Åó-äåêëàðàöè¼à Çà Ñîîáðàçíîñò, БАТЕРИИ, Îäðæóâàњå, Ñèìáîëè
Ве мoлиме прочитаjте го и
чувајте го ова упатство!
Мaкeдohcки
134134
Технічні характеристики, Вказівки З Техніки Безпеки, Використання за призначенням,
Сертифікат Відповідності Вимогам Єс, Акумуляторна, Обслуговування, Символи Прочитайте та збережіть цю інструкцію.
Українська
139139

  
148148

IX
TIP
II
IV
I
VII
V
III
VI
VIII

Zubehör
Accessoires
Accessorio
Accessorio Acessório
Toebehoren Tilbehør
Tilbehør Tillbehör
Lisälaite 
Aksesuar Příslušenství
Príslušenstv 
Azokat a tartozékokat
Oprema Piederumi
Priedas Tarvikud
Äîïîëíèòåëü 
Accesoriu 
 


22
I

33
II
2.
3.
1
2
1.

44
III
0°0°
30°30° 30°30°
60°60° 60°60°
3030
°°
6060
°°
3030
°°
6060
°°
00
°°
clickclick

55
IV
1. 2.
3.
< 6 mm
> 6 mm
4.

66
IV
3.
2.
1.

77
V
unlockunlock
locklock
Start
Stop
1. 2.
1. 2.

88
V
Startup protection:
When switched on, the machine will not start up after
voltage breakdown. To continue working, switch the
machine o and then on again.
Wiederanlaufschutz:
Eingeschaltete Maschine läuft nach Spannungsausfall nicht
wieder an. Um weiter zu arbeiten Maschine aus- und wieder
einschalten.
Dispositif de protection contre un redemarrage
Après une coupure de tension, la machine enclenchée
ne redémarre pas. Pour continuer à travailler, il convient
d’éteindre la machine et de l’enclencher à nouveau.
Protezione contro il riavvio
La macchina accesa non riparte in seguito alla caduta della
tensione. Per poter continuare a lavorare bisogna prima
spegnere e poi riaccendere la macchina.
Protección contra el rearranque
La máquina conectada no se vuelve a poner en marcha
después de un fallo de corriente. Para continuar el trabajo,
desconectar y volver a conectar la máquina.
Protecção de reinício
Quando está ligada, após uma falha de energia a máquina
não retoma o seu funcionamento. Para prosseguir o
trabalho, desligar a máquina e voltar a ligá-la.
Herstartbeveiliging
Na spanningsuitval schakelt de machine niet automatisch
weer in. Schakel de machine uit en weer in om door te
kunnen werken.
Genstartsbeskyttelse
I tilfælde af spændingsudfald, mens maskinen kører, går den
ikke i gang igen, når spændingen kommer tilbage. For at
genoptage arbejdet skal maskinen slukkes og tændes igen.
Automatisk gjenstartsbeskyttelse
En påslått maskin begynner ikke automatisk å gå igjen etter
strømbrudd. For å kunne fortsette å arbeide må maskinen
skues av og så på igjen.
Återstartsskydd
En påslagen maskin startar inte själv efter ett strömavbrott.
Stäng först av och slå sedan på maskinen igen för att
fortsätta att arbeta.
Uudelleenkäynnistyssuoja
Päällekytketty kone ei käynnisty sähkökatkon jälkeen
uudestaan. Työn jatkamiseksi tulee kone sammuttaa ja
käynnistää uudelleen.
Προστασια επανεκκινησης
Η ενεργοποιημένη μηχανή δεν ξεκινά πάλι από μόνη της μετά
από μια πτώση ρεύματος. Για να συνεχίσετε την εργασία,
απενεργοποιείτε και ενεργοποιείτε πάλι τη μηχανή.
Tekrar çaliştirmada koruma
Çalıştırılan makine voltaj kaybından sonra yeniden çalışmaz.
Makineyi tekrar çalıştırmak için kapatın ve tekrar açın.
Ochrana proti opětovnému náběhu
Zapnutá rozbrušovačka se v případě výpadku proudu po
jeho opětovném zapnutí sama nerozběhne. K pokračování
práce se rozbrušovačka musí vypnout a opět zapnout.
Ochrana proti opätovnému nábehu
Zapnutá rozbrusovačka sa v prípade výpadku prúdu po jeho
opätovnom zapnutí sama nerozbehne. K pokračovaniu práce
sa rozbrusovačka musí vypnúť a opäť zapnúť.
Zabezpieczenie przed ponownym uruchomieniem
Włączone urządzenie nie uruchamia się z powrotem po
ustąpienia zaniku napięcia. Aby móc kontynuować pracę,
urządzenie należy wyłączyć, a potem z powrotem włączyć.
Újraindulás elleni védelem
A bekapcsolt gép feszültségkimaradás után ismét elindul. A
munka folytatásához a gépet ki és újra be kell kapcsolni.
Zaščita pred ponovnim zagonom
Vklopljen stroj se po izpadu napetosti ponovno ne zažene.
Za nadaljevanje dela stroj izklopite in ponovno vklopite.
Zaštita protiv ponovnog pokretanja
Uključeni stroj poslilje nestanka napona više ne starta. Da bi
se dalje radilo, stroj isključiti i ponovno uključiti.
Aizsardzība pret atkārtotu palaišanu
Pārtrūkstot strāvas padevei, ieslēgtā ierīce no jauna
neieslēdzas. Darba turpināšanai ierīci izslēgt un ieslēgt no
jauna.
Apsauga nuo pakartotinio įsijungimo
Jei darbo metu dingsta įtampa, ją sutvarkius, mašina
neįsijungia automatiškai. Norint vėl dirbti su mašina, reikia ją
išjungti ir vėl įjungti.
Taaskäivituskaitse
Sisselülitatud masin ei käivitu enam uuesti pärast
voolukatkestust. Töö jätkamiseks lülitage masin välja ja seejärel
taas sisse.
Защита от повторного включения
При исчезновении напряжения устройство не работает.
Для продолжения работы устройство выключите и снова
включите.
Защита от повторно пускане След спиране на
електрозахранването включената машина не започва
да работи отново. За да продължите работа изключете и
отново включете машината.
Protecţie contra repornirii
Maşina conectată nu reporneşte după o întrerupere de
curent. Pentru a putea lucra în continuare, maşina trebuie
oprită şi apoi repornită.
Заштита од повторно придвижување
Вклучената машина во случај на снемување струја не
се вклучува повторно. За да продолжите со работа
исклучете ја машината и вклучете ја повторно.
Захист від повторного запуску
Увімкнена машина не продовжує роботу після того, як
була вставлена акумуляторна батарея.






99
VI

AGV 15-125 XE

1010
TIP
< 30°< 30°
TIP
VII
TIP

1111
1. 2.
2.1.
VIII

Zubehör
Accessoires
Accessorio
Accessorio
Acessório
Toebehoren
Tilbehør
Tilbehør
Tillbehör
Lisälaite

Aksesuar

Príslušenstv

Tartozékokat
Oprema
Piederumi
Prieda
Tarvikud
Aksessuaarid
Äîïîëíèòåëü

Accesoriu




1212
3.
1. 2.
VIII

Zubehör
Accessoires
Accessorio
Accessorio
Acessório
Toebehoren
Tilbehør
Tilbehør
Tillbehör
Lisälaite

Aksesuar

Príslušenstv

Tartozékokat
Oprema
Piederumi
Prieda
Tarvikud
Aksessuaarid
Äîïîëíèòåëü

Accesoriu




1313
2.
1.
3.
VIII

Zubehör
Accessoires
Accessorio
Accessorio
Acessório
Toebehoren
Tilbehør
Tilbehør
Tillbehör
Lisälaite

Aksesuar

Príslušenstv

Tartozékokat
Oprema
Piederumi
Prieda
Tarvikud
Aksessuaarid
Äîïîëíèòåëü

Accesoriu




1414
GB
English
WARNING!
Read all safety warnings and all instructions. Failure to
follow the warnings and instructions may result in electric shock,
re and/or serious injury.
Save all warnings and instructions for future reference.
ANGLE GRINDER SAFETY WARNINGS
Safety Warnings Common for Grinding, Sanding, Wire
Brushing or Abrasive Cutting-O Operations:
a) This power tool is intended to function as a grin-
der, sander, wire brush or cut-o tool. Read all safety
warnings, instructions, illustrations and specications
provided with this power tool. Failure to follow all instructions
listed below may result in electric shock, re and/or serious injury.
b) Operations such as polishing are not recommended
to be performed with this power tool.Operations for which
the power tool was not designed may create a hazard and cause
personal injury.
c) Do not use accessories which are not specically desi-
gned and recommended by the tool manufacturer. Just
because the accessory can be attached to your power tool, it does
not assure safe operation.
d) The rated speed of the accessory must be at least equal
to the maximum speed marked on the power tool. Accesso-
ries running faster than their rated speed can break and y apart.
e) The outside diameter and the thickness of your acces-
sory must be within the capacity rating of your power
tool. Incorrectly sized accessories cannot be adequately guarded
or controlled.
TECHNICAL DATA
Angle Grinder AGV 15-125 XC AGV 15-125 XE AGV 15-150 XC
Production code 4584 64 03...
... 000001-999999 4584 68 03... ... 000001-999999 4584 72 03... ... 000001-999999
Rated input 1550W 1550W 1550W
Rated speed 11000 min-1 2800-11000 min-1 9000 min-1
D= Grinding disc diameter max.
d= Grinding disc hole diameter
125mm
22,2 mm 125 mm 22,2 mm 150 mm 22,2 mm
b= Cutting disc thickness min. / max.
1 / 3 mm 1 / 3 mm 1 / 3 mm
b= Grinding disc thickness max. 6 mm 6 mm 6 mm
D= Grinding surface diameter max. 125 mm 125 mm 150 mm
D= Wiring brush diameter max. 75 mm 75 mm 75 mm
Thread of work spindle M 14 M 14 M 14
Weight according EPTA-Procedure 01/2014 2,6 kg 2,6 kg 2,6 kg
Noise information
Measured values determined according to EN 60745. Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A))
Sound power level (Uncertainty K=3dB(A))
Wear ear protectors!
86,5 dB(A)
97,5 dB(A) 86,5 dB(A) 97,5 dB(A) 86,5 dB(A) 97,5 dB(A)
Vibration information
Vibration total values (triaxial vector sum) determined according to EN 60745
Surface grinding: Vibration emission value ah,SG
Uncertainty K=
4,7 m/s2
1,5 m/s2
4,7 m/s2
1,5 m/s2
4,7 m/s2
1,5 m/s2
Disc sanding: Vibration emission value ah,DS
Uncertainty K=
4,5 m/s2
1,5 m/s2
4,5 m/s2
1,5 m/s2
4,5 m/s2
1,5 m/s2
For other applications, e.g. Abrasive Cutting-O Operations or Wire Brushing other vibration values could occur.
WARNING!
The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized test given in EN 60745 and may
be used to compare one tool with another.It may be used for a preliminary assessment of exposure.The declared vibration and noise emission level repre-
sents the main applications of the tool. However if the tool is used for dierent applications, with dierent accessories or poorly maintained, the vibration
and noise emission may dier. This may signicantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration and noise should also take into account the times when the tool is switched o or when it is running but
not actually doing the job. This may signicantly reduce the exposure level over the total working period.Identify additional safety measures to protect the
operator from the eects of vibration and/or noise such as: maintain the tool and the accessories, keep the hands warm, organization of work patterns.Wear
ear protectors. Exposure to noise can cause hearing loss.

1515
GB
English
f) Threaded mounting of accessories must match the
grinder spindle thread. For accessories mounted by an-
ges, the arbour hole of the accessory must t the locating
diameter of the ange. Accessories that do not match the
mounting hardware of the power tool will run out of balance,
vibrate excessively and may cause loss of control.
g) Do not use a damaged accessory. Before each use inspect
the accessory such as abrasive wheels for chips and cracks,
backing pad for cracks, tear or excess wear, wire brush for
loose or cracked wires. If power tool or accessory is dropped,
inspect for damage or install anundamaged accessory.
After inspecting and installing an accessory,positionyour-
self and bystanders away from the plane of the rotating
accessory and run thepower tool at maximumno-load
speedfor one minute.Damaged accessories will normally break
apart during this test time.
h) Wearpersonalprotectiveequipment. Depending onap-
plication, use faceshield,safety goggles or safety glasses.
As appropriate,weardust mask,hearing protectors, gloves
and workshop apron capable of stopping smallabrasiveor
workpiecefragments. The eye protection must be capable of
stopping ying debris generated by various operations. The dust
mask or respirator must be capable of ltrating particles generated
by your operation. Prolonged exposure to high intensity noise may
cause hearing loss.
i) Keep bystanders a safe distance away from work area.
Anyoneenteringtheworkarea mustwearpersonal protec-
tiveequipment.Fragments of workpiece or of a broken accessory
may y away and cause injury beyond immediate area of operation.
j) Hold the power tool by insulated gripping surfaces only,
when performing an operation where the cutting accessory
may contact hidden wiring or its own cord. Cutting accessory
contacting a “live” wire may make exposed metal parts of the power
tool “live” and could give the operator an electric shock.
k) Positionthecord clearof the spinningaccessory. If you
lose control, the cord may be cut or snagged and your hand or arm
may be pulled into the spinning accessory.
l) Never lay the powertool down until the accessory has
come to a complete stop. The spinning accessory may grab the
surface and pull the power tool out of your control.
m) Do not run the power tool while carrying it at your side.
Accidental contact with the spinning accessory could snag your
clothing, pulling the accessory into your body.
n) Regularly clean the power tool’s air vents. The motor’s fan
will draw the dust inside the housing and excessive accumulation of
powdered metal may cause electrical hazards.
o) Donot operate the powertoolnearammable materi-
als. Sparks could ignite these materials.
p) Donot use accessories that requireliquid coolants. Using
water or other liquid coolants may result in electrocution or shock.
Kickback and Related Warnings
Kickback is a sudden reaction to a pinched or snagged rotating
wheel, backing pad, brush or any other accessory. Pinching or
snagging causes rapid stalling of the rotating accessory which
in turn causes the uncontrolled power tool to be forced in the
direction opposite of the accessory’s rotation at the point of the
binding.
For example, if an abrasive wheel is snagged or pinched by the
workpiece, the edge of the wheel that is entering into the pinch
point can dig into the surface of the material causing the wheel
to climb out or kick out. The wheel may either jump toward or
away from the operator, depending on direction of the wheel’s
movement at the point of pinching. Abrasive wheels may also
break under these conditions.
Kickback is the result of power tool misuse and/or incorrect
operating procedures or conditions and can be avoided by taking
proper precautions as given below.
a) Maintain a rm grip on the power tool and position your
body and arm to allow you to resist kickback forces. Always
use auxiliary handle, if provided, for maximum control over
kickback or torque reaction during start-up. The operator can
control torque reactions or kickback forces, if proper precautions
are taken.
b) Never place your hand near the rotating accessory.
Accessory may kickback over your hand.
c) Do not position your body in the area where power tool
will move if kickback occurs. Kickback will propel the tool in di-
rection opposite to the wheel’s movement at the point of snagging.
d) Use special care when working corners, sharp edges etc.
Avoid bouncing and snagging the accessory. Corners, sharp
edges or bouncing have a tendency to snag the rotating accessory
and cause loss of control or kickback.
e) Do not attach a saw chain woodcarving blade or toothed
saw blade. Such blades create frequent kickback and loss of control.
Safety Warnings Specic for Grinding and Abrasive
Cutting-O Operations:
a) Use only wheel types that are recommended for your
power tool and the specic guard designed for the selected
wheel. Wheels for which the power tool was not designed cannot
be adequately guarded and are unsafe.
b) The grinding surface of the centre depressed wheels
must be mounted below the plane of the guard lip. An
improperly mounted wheel that projects through the plane of the
guard lip cannot be adequately protected.
c) The guard must be securely attached to the power tool
and positioned for maximum safety, so the least amount
of wheel is exposed towards the operator. The guard helps
to protect the operator from broken wheel fragments, accidental
contact with wheel and sparks that could ignite clothing.
d) Wheels must be used only forrecommended applications.
For example: do not grind with the side of cut-o wheel. Abra-
sive cut-o wheels are intended for peripheral grinding, side forces
applied to these wheels may cause them to shatter.
e) Always use undamaged wheel anges that areof correct
size and shape for your selected wheel. Proper wheel anges
support the wheel thus reducing the possibility of wheel breakage.
Flanges for cut-o wheels may be dierent from grinding wheel
anges.
f) Do not use worn down wheels from larger power tools.
Wheel intended for larger power tool is not suitable for the higher
speed of a smaller tool and may burst.

1616
GB
English
Additional Safety Warnings Specic for Abrasive Cutting-O
Operations:
a) Do not “jam” the cut-o wheel or apply excessive
pressure. Do not attempt tomakean excessive depth of cut.
Overstressing the wheel increases the loading and susceptibility
to twisting or binding of the wheel in the cut and the possibility of
kickback or wheel breakage.
b) Do not position your body in line with and behind the ro-
tating wheel.When the wheel, at the point of operation, is moving
away from your body, the possible kickback may propel the spinning
wheel and the power tool directly at you.
c) When wheel is binding or when interrupting a cut for any
reason, switch o the power tool and hold the power tool
motionless until the wheel comes to a complete stop. Never
attempt to remove the cut-o wheel from the cut while the
wheel is in motion otherwise kickback may occur. Investigate
and take corrective action to eliminate the cause of wheel binding.
d) Do not restart the cutting operation in the workpiece. Let
the wheel reach full speed and carefully re-enter the cut. The
wheel may bind, walk up or kickback if the power tool is restarted in
the workpiece.
e) Support panels or any oversized workpiece to minimize
the risk of wheel pinching and kickback. Large workpieces tend
to sag under their own weight. Supports must be placed under the
workpiece near the line of cut and near the edge of the workpiece on
both sides of the wheel.
f) Use extra caution when making a “pocket cut” into exis-
tingwalls or otherblindareas. The protruding wheel may cut gas
or water pipes, electrical wiring or objects that can cause kickback.
Safety Warnings Specic for Sanding Operations:
a) Do not use excessively oversized sanding disc paper.
Follow manufacturers recommendations, when selecting
sanding paper. Larger sanding paper extending beyond the san-
ding pad presents a laceration hazard and may cause snagging,
tearing of the disc or kickback.
Safety Warnings Specic for Wire Brushing Operations:
a) Be aware that wire bristles are thrown by the brush
even during ordinary operation. Do not overstress the
wires by applying excessive load to the brush. The wire
bristles can easily penetrate light clothing and/or skin.
b) If the use of a guard is recommended for wire brushing,
do not allow any interference of the wire wheel or brush
with the guard. Wire wheel or brush may expand in diameter
due to work load and centrifugal forces.
Additional Safety and Working Instructions
When grinding metal, ying sparks are produced. Take care that
no persons are endangered. Because of the danger of re, no
combustible materials should be located in the vicinity (spark
ight zone). Do not use dust extraction.
Avoid ying sparks and sanding dust hit your body.
Never reach into the danger area of the machine when it is
running.
Immediately switch o the machine in case of considerable
vibrations or if other malfunctions occur. Check the machine in
order to nd out the cause.
Under extreme conditions (e.g. smooth-grinding metals with
the arbour and vulcanized bre grinding wheel), signicant
contamination can build up on the inside of the angle grinder. For
safety reasons, in such conditions a ground fault interrupter must
be connected in series. If the ground fault interrupter trips the
machine must be sent for service.
Chips and splinters must not be removed while the machine is
running.
Do not let any metal parts enter the airing slots - danger of short
circuit!
MAINS CONNECTION
Connect only to single-phase AC system voltage as indicated on
the rating plate. It is also possible to connect to sockets without an
earthing contact as the design conforms to safety class II.
Appliances used at many dierent locations including wet room
and open air must be connected via a residual current device (FI,
RCD, PRCD) of 30mA or less.
Only plug-in when machine is switched o.
Inrush currents cause short-time voltage drops. Under unfavoura-
ble power supply conditions, other equipment may be aected. If
the system impedance of the power supply is lower than 0,2 Ohm,
disturbances are unlikely to occur.
SPECIFIED CONDITIONS OF USE
The angle grinder is intended for grinding and cutting metal,
stone and ceramicmaterials as well as sanding and wire brushing.
Use the cutting guard from the accessories range for cutting
application.
Please refer to the instructions supplied by the accessory
manufacturer.
The machine is suitable only for working without water.
WORKING INSTRUCTIONS
For accessories intended to be tted with threaded hole wheel,
ensure that the thread in the wheel is long enough to accept the
spindle length.
Always use and store the cutting and grinding wheels according
to the manufacturer‘s instructions.
Always use the correct guard for cutting and grinding.
The grinding surface of the centre depressed wheels must be
mounted min. 2 mm below the plane of the guard lip.
The adjusting nut must be tightened before starting to work with
the machine.
Always use the auxiliary handle.
The workpiece must be xed if it is not heavy enough to be steady.
Never move the workpiece towards the rotating wheel by hand.
ELECTRONICS
The built-in electronic will keep a constant speed even under
increased load.
In case of overload, the rotational speed is being reduced until
machine stops.
The machine has an overload and anti-kickback safety function
and stops if it is overloaded.
Please note that the machine will automatically accelerate back to
its original operating speed if the load is removed from it.
RESTART PROTECTION
Machines with a lockable switch are supplied with a restart
cutout. This prevents the machine restarting by itself after a
power failure. When resuming work, switch the machine o and
then switch it back on again.

1717
GB
English
SOFT START
Electronic soft start for save use prevents jerky run-up of the
machine.
MAINTENANCE
The ventilation slots of the machine must be kept clear at all
times.
If the supply cord of this power tool is damaged, it must be
replaced by a specially prepared cord available through the service
organization.
Use onlyMilwaukeeaccessories andMilwaukeespareparts. Should
components need to be replaced which have not been described,
please contact one of our Milwaukee service agents (see our list of
guarantee/serviceaddresses).
If needed, an exploded view of the tool can be ordered. Please
state the Article No. as well as the machine type printed on the
label and order the drawing at your local service agents or directly
at: Techtronic Industries GmbH, Max-Eyth-Straße10, 71364Win-
nenden, Germany.
ECDECLARATION OF CONFORMITY
We declare under our sole responsibility that the product
described under “Technical Data” fullls all the relevant provisions
of the directives
2011/65/EU(RoHS)
2006/42/EC
2014/30/EU
and the following harmonized standards have been used.
EN 60745-1:2009 + A11:2010
EN 60745-2-3:2011+A2:2013
EN 55014-1:2017+A11:2020
EN 55014-2:2015
EN 61000-3-2:2014
EN 61000-3-3:2013
EN IEC 63000:2018
Winnenden, 2020-11-13
Alexander Krug / Managing Director
Authorized to compile the technical le
Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany
GBDECLARATION OF CONFORMITY
We declare as the manufacturer under our sole responsibility
that the product described under „Technical Data“ fullls all the
relevant provisions of the following Regulations
S.I. 2012/3032 (as amended), S.I. 2008/1597 (as amended),
S.I. 2016/1091 (as amended) and that the following designated
standards have been used:
BS EN 60745-1:2009+A11:2010
BS EN 60745-2-3:2011+A13:2015
BS EN 55014-1:2017+A11:2020
BS EN 55014-2:2015
BS EN 61000-3-2:2014
BS EN 61000-3-3:2013
BS EN IEC 63000:2018
Winnenden, 2020-11-13
Alexander Krug / Managing Director
Authorized to compile the technical le
Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany
SYMBOLS
CAUTION! WARNING! DANGER!
Please read the instructions carefully before starting the
machine.
Always wear goggles when using the machine.
Wear gloves!
Always disconnect the plug from the socket before
carrying out any work on the machine.
Do not use force.
Only for cutting work.
Only for grinding.
Accessory - Not included in standard equipment, availa-
ble as an accessory.
Do not dispose of electric tools together with household was-
te material.Electric tools andelectronic equipment that have
reached the end of their life must be collected separately and
returned to an environmentally compatible recycling facility.
Check with your local authority or retailer for recycling advice
andcollectionpoint.
Class II tool. Tool in which protection against electric
shock does not rely on basic insulation only, but in which
additional safety precautions, such as double insulation
or reinforced insulation, are provided. There being
no provision for protective earthing or reliance upon
installation conditions.
European Conformity Mark
British Conformity Mark
Ukraine Conformity Mark
EurAsian Conformity Mark

1818
D
Deutsch
WARNUNG!
Lesen Sie alle Sicherheitshinweise und Anweisungen.
Versäumnisse bei der Einhaltung der Sicherheitshinweise und An-
weisungen können elektrischen Schlag, Brand und/oder schwere
Verletzungen verursachen.
Bewahren Sie alle Sicherheitshinweise und Anweisungen
für die Zukunft auf.
SICHERHEITSHINWEISE FÜR WINKELSCHLEIFER
Gemeinsame Sicherheitshinweise zum Schleifen,
Sandpapierschleifen, Arbeiten mit Drahtbürsten und
Trennschleifen:
a) Dieses Elektrowerkzeug ist zu verwenden als Schleifer,
Sandpapierschleifer, Drahtbürste und Trennschleifma-
schine. Beachten Sie alle Sicherheitshinweise, Anwei-
sungen, Darstellungen und Daten, die Sie mit dem Gerät
erhalten. Wenn Sie die folgenden Anweisungen nicht beachten,
kann es zu elektrischem Schlag, Feuer und/oder schweren
Verletzungen kommen.
TECHNISCHE DATEN
Winkelschleifer AGV 15-125 XC AGV 15-125 XE AGV 15-150 XC
Produktionsnummer 4584 64 03...
... 000001-999999 4584 68 03... ... 000001-999999 4584 72 03... ... 000001-999999
Nennaufnahmeleistung 1550 W 1550 W 1550 W
Nenndrehzahl 11000 min-1 2800-11000 min-1 9000 min-1
D= Schleifscheibendurchmesser max.
d= Bohrungsdurchmesser
125mm
22,2 mm 125 mm 22,2 mm 150 mm 22,2 mm
b= Trennscheibendicke min. / max.
1 / 3 mm 1 / 3 mm 1 / 3 mm
b= Schleifscheibendicke max. 6 mm 6 mm 6 mm
D= Schleiächendurchmesser max. 125 mm 125 mm 150 mm
D= Topfbürstendurchmesser max. 75 mm 75 mm 75 mm
Spindelgewinde M 14 M 14 M 14
Gewicht nach EPTA-Prozedur 01/2014 2,6 kg 2,6 kg 2,6 kg
Geräuschinformation
Messwerte ermittelt entsprechend EN 60745. Der A-bewertete Geräuschpegel des Gerätes beträgt typischerweise:
Schalldruckpegel (Unsicherheit K=3dB(A))
Schallleistungspegel (Unsicherheit K=3dB(A))
Gehörschutz tragen!
86,5 dB(A)
97,5 dB(A) 86,5 dB(A) 97,5 dB(A) 86,5 dB(A) 97,5 dB(A)
Vibrationsinformationen
Schwingungsgesamtwerte (Vektorsumme dreier Richtungen) ermittelt entsprechend EN 60745.
Oberächenschleifen: Schwingungsemissionswert ah,SG
Unsicherheit K=
4,7 m/s2
1,5 m/s2
4,7 m/s2
1,5 m/s2
4,7 m/s2
1,5 m/s2
Schleifen mit Schleifblatt: Schwingungsemissionswert ah,DS
Unsicherheit K=
4,5 m/s2
1,5 m/s2
4,5 m/s2
1,5 m/s2
4,5 m/s2
1,5 m/s2
Bei anderen Anwendungen, wie z.B. Trennschleifen oder Schleifen mit der Stahldrahtbürste können sich andere Vibrationswerte ergeben!
WARNUNG!
Die angegebenen Schwingungsgesamtwerte und Geräuschemissionswerte wurden nach einem genormten Messverfahren gemäß EN 60745 gemessen und
können für den Vergleich von Elektrowerkzeugen miteinander verwendet werden.Sie können für eine vorläuge Einschätzung der Belastung verwendet
werden.Der angegebene Schwingungs- und Geräuschemissionspegel repräsentiert die hauptsächlichen Anwendungen des Elektrowerkzeugs. Wenn
allerdings das Elektrowerkzeug für andere Anwendungen, mit abweichenden Einsatzwerkzeugen oder ungenügender Wartung eingesetzt wird, können
sich die Schwingungs- und Geräuschemissionen unterscheiden. Dies kann deren Wirkung über den gesamten Arbeitszeitraum deutlich erhöhen.Bei der
Abschätzung der Belastung durch Schwingungen und Lärm sollten auch die Zeiten berücksichtigt werden, in denen das Elektrowerkzeug ausgeschaltet ist
oder zwar läuft, aber keine tatsächliche Arbeit verrichtet wird. Dies kann deren Wirkung über den gesamten Arbeitszeitraum deutlich reduzieren.Legen
Sie zusätzliche Sicherheitsmaßnahmen zum Schutz des Bedieners vor den Auswirkungen von Schwingungen- und / oder Lärm fest, wie z. B.: Wartung des
Werkzeugs und des Zubehörs, Warmhalten der Hände, Organisation der Arbeitsabläufe.Tragen Sie Gehörschutz. Die Einwirkung von Lärm kann Gehörver-
lust bewirken.