AEG A18SRSBL User manual
A18SRSBL
Original instructions
Important!
It is essential that you read the instructions in this manual before
assembling, operating and maintaining the product.
6XEMHFWWRWHFKQLFDOPRGL¿FDWLRQV
Handle,
insulated gripping surface
Lock-off button
Blade release mechanism
LED light
Battery port
Shoe assembly
Blade
Trigger switch
4
14
15
8
11
12
START
STOP
5
10
10
6
6
1
1
1
1
1
1
1
2
1
2
click
Remove the battery pack before
starting any work on the product.
7
75-100 %
50-75 %
25-50 %
0-25 %
8
1
2
1
2
9
10
LOCK
UNLOCK
11
12
START
STOP
STOP
START
1
2
13
Handle (insulated gripping surface)
14
1
2
3
15
1
2
3
16 ENGLISH
TECHNICAL DATA A18SRSBL
Type Cordless reciprocating saw
Battery voltage 18 V
Stroke rate under no-load 0-3200 min-1
Length of stroke 22 mm
Cutting capacity
Wood 100 mm
Metal 40 mm
PVC pipe 75 mm
Weight without battery pack 1.78 kg
Noise Information
Measured values determined according to EN 62841. Typically, the A-weighted noise
levels of the tool are:
Sound pressure level / Uncertainty
Sound power level / Uncertainty
Wear ear protection!
LpA=87.0 dB (A) / KpA=5 dB(A)
LWA=98.0 dB (A) / KWA=5 dB(A)
Vibration Information
Vibration total values (triaxial vector sum) determined according to EN 62841.
Vibration emission value / Uncertainty
Cutting board
Cutting wooden beam
ah,B=7.5 m/s2 / K=1.5 m/s2
ah ,WB=8.0 m/s2 / K=1.5 m/s2
WARNING!
The declared vibration total values and the declared noise emission values given in this instruction manual have been measured in
accordance with a standardised test and may be used to compare one tool with another. They may be used for a preliminary assessment of
exposure.
7KHGHFODUHGYLEUDWLRQDQGQRLVHHPLVVLRQYDOXHVUHSUHVHQWWKHPDLQDSSOLFDWLRQVRIWKHWRRO+RZHYHULIWKHWRROLVXVHGIRUGLႇHUHQW
DSSOLFDWLRQVXVHGZLWKGLႇHUHQWDFFHVVRULHVRUSRRUO\PDLQWDLQHGWKHYLEUDWLRQDQGQRLVHHPLVVLRQPD\GLႇHU7KHVHFRQGLWLRQVPD\
VLJQL¿FDQWO\LQFUHDVHWKHH[SRVXUHOHYHOVRYHUWKHWRWDOZRUNLQJSHULRG
$QHVWLPDWLRQRIWKHOHYHORIH[SRVXUHWRYLEUDWLRQDQGQRLVHVKRXOGWDNHLQWRDFFRXQWWKHWLPHVZKHQWKHWRROLVWXUQHGRႇRUZKHQLWLV
UXQQLQJLGOH7KHVHFRQGLWLRQVPD\VLJQL¿FDQWO\UHGXFHWKHH[SRVXUHOHYHORYHUWKHWRWDOZRUNLQJSHULRG
,GHQWLI\DGGLWLRQDOVDIHW\PHDVXUHVWRSURWHFWWKHRSHUDWRUIURPWKHHႇHFWVRIYLEUDWLRQDQGQRLVHVXFKDVPDLQWDLQLQJWKHWRRODQGWKH
accessories, keeping the hands warm (in case of vibration), and organising work patterns.
COMPATIBLE BATTERY PACKS (NOT INCLUDED)
L1820R
L1820S
A18FB2
L1825R
L1830R-X5
A18B4
L1840R
A18FB4
L1850R
A18FB5
L1860R
L1860R-X5
L1890R
Use AEG 18V battery and charger only
WARNING! Read all safety warnings, instructions,
LOOXVWUDWLRQVDQGVSHFL¿FDWLRQVSURYLGHGZLWKWKLVSRZHUWRRO
Failure to follow all instructions listed below may result in electric
VKRFN¿UHDQGRUVHULRXVLQMXU\6DYHDOOZDUQLQJVDQGLQVWUXFWLRQ
for future reference.
RECIPROCATING SAW SAFETY WARNINGS
+ROGWKHSRZHUWRROE\LQVXODWHGJULSSLQJVXUIDFHVZKHQ
SHUIRUPLQJDQRSHUDWLRQZKHUHWKHFXWWLQJDFFHVVRU\PD\
FRQWDFWKLGGHQZLULQJ Cutting accessory contacting a “live” wire
may make exposed metal parts of the power tool “live” and could
give the operator an electric shock.
8VHFODPSVRUDQRWKHUSUDFWLFDOZD\WRVHFXUHDQGVXSSRUWWKH
ZRUNSLHFHWRDVWDEOHSODWIRUP Holding the workpiece by hand or
against your body leaves it unstable and may lead to loss of control.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
:HDUHDUSURWHFWRUV Exposure to noise can cause hearing loss.
Always wear goggles when using the machine. It is recommended
to wear gloves, sturdy non slipping shoes and apron.
Sawdust and splinters must not be removed while the machine is
running.
Always use the protective shields on the machine.
The dust produced when using this tool may be harmful to health.
Do not inhale the dust. Wear a suitable dust protection mask.
Do not use cracked or distorted saw blades.
Plunge cuts without pre-drilling a hole are possible with soft
materials (wood, light building materials for walls). Harder materials
PHWDOVPXVW¿UVWEHGULOOHGZLWKDKROHFRUUHVSRQGLQJWRWKHVL]HRI
the saw blade.
Always place the guide shoe on the workpiece when sawing.
:KHQZRUNLQJLQZDOOVFHLOLQJRUÀRRUWDNHFDUHWRDYRLGHOHFWULF
cables and gas or water pipes.
Remove the battery pack before starting any work on the product.
7KHSURGXFWZLOOUHVWDUWDXWRPDWLFDOO\LIVWDOOHG7XUQRႇWKHSURGXFW
immediately if it stalls. Do not turn on the product again while it is
Ambient temperature range for tool during operation is between 0°C
and 40°C.
Ambient temperature range for tool storage is between 0°C and
40°C.
The recommended ambient temperature range for the charging
system during charging is between 10°C and 38°C.
ADDITIONAL BATTERY SAFETY WARNINGS
WARNING!7RUHGXFHWKHULVNRI¿UHSHUVRQDOLQMXU\DQG
product damage due to a short circuit, never immerse your tool,
EDWWHU\SDFNRUFKDUJHULQÀXLGRUDOORZDÀXLGWRÀRZLQVLGHWKHP
&RUURVLYHRUFRQGXFWLYHÀXLGVVXFKDVVHDZDWHUFHUWDLQLQGXVWULDO
chemicals, and bleach or bleach containing products, etc., can
cause a short circuit.
Do not dispose of used battery packs in the household refuse or
E\EXUQLQJWKHP$(*'LVWULEXWRUVRႇHUWRUHWULHYHROGEDWWHULHVWR
protect our environment.
17
ENGLISH
Do not store the battery pack together with metal objects (short
circuit risk).
Use only System AEG chargers for charging System AEG battery
packs. Do not use battery packs from other systems.
No metal parts must be allowed to enter the battery section of the
charger (short circuit risk).
Never break open battery packs and chargers and store only in dry
rooms. Keep dry at all times.
Battery acid may leak from damaged batteries under extreme load
or extreme temperatures. In case of contact with battery acid wash
LWRႇLPPHGLDWHO\ZLWKVRDSDQGZDWHU,QFDVHRIH\HFRQWDFWULQVH
thoroughly for at least 10 minutes and immediately seek medical
attention.
Ambient temperature range for battery during use is between 0°C
and 40°C.
Ambient temperature range for battery storage is between 0°C and
20°C.
SPECIFIED CONDITIONS OF USE
The reciprocating saw is intended to cut wood, plastics, and metal.
The product can cut straight lines, curves, and internal cut-outs. The
SURGXFWFXWVSLSHVDQGFDQFXWÀXVKWRDVXUIDFH
Do not use the product for any other purpose.
BATTERIES
Battery packs which have not been used for some time should be
recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance of
the battery pack. Avoid extended exposure to heat or sunshine (risk
of overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, the battery packs have to be fully charged,
after used.
To obtain the longest possible battery life remove the battery pack
from the charger once it is fully charged.
)RUEDWWHU\SDFNVWRUDJHORQJHUWKDQGD\V
• Store the battery pack where the temperature is below 27°C and
away from moisture.
• Store the battery packs in a 30% - 50% charged condition.
• Every six months of storage, charge the pack as normal.
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods
Legislation requirements.
Transportation of those batteries has to be done in accordance with
local, national and international provisions and regulations.
• The user can transport the batteries by road without further
requirements.
• Commercial transport of Lithium-Ion batteries by third parties is
subject to Dangerous Goods regulations. Transport preparation
and transport are exclusively to be carried out by appropriately
trained persons and the process has to be accompanied by
corresponding experts.
:KHQWUDQVSRUWLQJEDWWHULHV
• Ensure that battery contact terminals are protected and insulated
to prevent short circuit.
• Ensure that battery pack is secured against movement within
packaging.
• Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice.
BATTERY PACK PROTECTION LI-ION BATTERY
The battery pack has overload protection that protects it from being
overloaded and helps to ensure long life. Under extreme stress the
battery electronics switch off the machine automatically. To restart,
switch the machine off and then on again. If the machine does not
start up again, the battery pack may have discharged completely. In
this case it must be recharged in the battery charger.
MAINTENANCE
Clean the product and guarding system with clean cloths or brushes.
The ventilation slots of the machine must be kept clear at all times.
Use only AEG accessories and AEG spare parts. Should
components need to be replaced which have not been described,
please contact one of our AEG service agents (see our list of
guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please state
the Article No. as well as the machine type printed on the label and
order the drawing at your local service agents or directly at:
7HFKWURQLF,QGXVWULHV$XVWUDOLD3W\/WG
PO Box 1065
Mount Waverley VIC 3149
Tel. no. 1300 234 797
Australia
7HFKWURQLF,QGXVWULHV1=/LPLWHG
PO Box 12-806
Penrose AUCKLAND 1642
Tel. no. 0800 234 797(0800 AEGPWR)
New Zealand
MAINTENANCE
Use only AEG accessories and spare parts. Should components
that have not been described need to be replaced, contact one
of our AEG service agents (see our list of guarantee/service
addresses).
If needed, an exploded view of the product can be ordered. State
the product type and the serial number printed on the label,
and order the drawing at your local service agents or directly
at: Techtronic Industries GmbH, Max-Eyth-Straße 10, 71364
Winnenden, Germany.
SYMBOLS
Read the instructions carefully before starting the
product.
CAUTION! WARNING! DANGER!
Remove the battery pack before starting any work on
the product.
Wear eye protection.
Wear ear protectors.
Wear a suitable dust protection mask.
Wear protective gloves.
Do not dispose of electric tools, batteries/rechargeable
batteries together with household waste material.
Electric tools and batteries that have reached the end
of their life must be collected separately and returned
to an environmentally compatible recycling facility.
Check with your local authority or retailer for recycling
advice and collection point.
No-load speed
V
Volts
Direct current
Regulatory Compliance Mark (RCM). Product
meets applicable regulatory requirements.
Techtronic Industries Australia Pty Ltd
31 Gilby Road, Mount Waverley,
VIC, 3149, Australia
Techtronic Industries N.Z. Limited
Unit C, 70 Business Parade South,
Highbrook, Auckland 2013, New Zealand
www.aegpowertools.com.au
www.aegpowertools.co.nz
AEG is a registered trade mark used under
license from AB Electrolux (publ).
961096811-01A
Table of contents
Other AEG Saw manuals
Popular Saw manuals by other brands
Draper
Draper 10.8V Instructions for
Makita
Makita LS1013F instruction manual
Felker
Felker Mason Mate II Operating instructions and parts list
Central Machinery
Central Machinery 32208 Set up and operating instructions
Craftsman
Craftsman RADIAL ARM SAW 315.22038 owner's manual
Ryobi
Ryobi RMS-1525 Operator's manual
