AEG ACS58B18 User manual

ACS58B18
A58CHS18B4
Original instructions

2
2
I mportant!
It is essential that you read the instructions in this manual before
assembling, operating, and maintaining the product.
Subject to technical modifications.

33
x 1
x 1
x 1 x 1
ACS58B18

4
4
BATTERY
PACK
SCABBARD
SAW
CHAIN
GUIDE BAR
FRONT HANDLE
SCRENCH
TOOL
TRIGGER
RELEASE
REAR
HANDLE
CHAIN
LUBRICANT
TANK CAP
CHAIN
TENSIONING
SCREW
FRONT HAND GUARD/
CHAIN BRAKE
BAR MOUNTING
NUTS
CHAIN
COVER SPIKED
BUMPER
x 1
x 1
x 1 x 1
x 1 x 1
A58CHS18B4

55
BATTERY
PACK
SCABBARD
SAW
CHAIN
GUIDE BAR
FRONT HANDLE
SCRENCH
TOOL
TRIGGER
RELEASE
REAR
HANDLE
CHAIN
LUBRICANT
TANK CAP
CHAIN
TENSIONING
SCREW
FRONT HAND GUARD/
CHAIN BRAKE
BAR MOUNTING
NUTS
CHAIN
COVER SPIKED
BUMPER

6
6
START
STOP
20
19
10
11
USING THE CHAIN BRAKE
ADJUSTING THE CHAIN TENSION
CLEANING THE PRODUCT
INSTALLING AND REMOVING THE SCABBARD

77
START
STOP
8
9
15 21
13
INSTALLING AND REMOVING THE SCABBARD
REPLACING THE CHAIN AND BAR STORING THE PRODUCT
USING THE PRODUCT
INSTALLING AND REMOVING THE BATTERY
ADDING CHAIN AND BAR OIL

8
8
1
2
2
1
click
START
STOP
INSTALLING AND REMOVING THE BATTERY
USING THE PRODUCT

99
1
2
2
1
click
START
STOP
USING THE PRODUCT

10
10
BRAKE ON
BRAKE OFF
4
2
1
3
USING THE CHAIN BRAKE
NOTE: The product does not turn on while the
chain brake is engaged.

11 11
BRAKE ON
BRAKE OFF
4
2
1
3
ADJUSTING THE CHAIN TENSION

12
12
3
4
2
1
FLATS
APPROX. 6.5 mm
6
7
click
5
7.85~9.8 Nm (80~100 Kgf-cm)
ADDING CHAIN AND BAR OIL
NOTE: The chain tension is correct when the gap
is 6.5 mm. Check the chain tension regularly, as
the chain stretches when it heats up.

13 13
3
4
2
1
FLATS
APPROX. 6.5 mm
6
7
click
5
7.85~9.8 Nm (80~100 Kgf-cm)
ADDING CHAIN AND BAR OIL

14
14
3
4
2
1
click
5
6
7
REPLACING THE CHAIN AND BAR

15 15
3
4
2
1
click
5
6
7
REPLACING THE CHAIN AND BAR

16
16
6
7
CHAIN DRIVE
LINKS
BAR
GROOVE
5
NOTE: Always properly dispose of used chain
and bar.
NOTE: For replacment chain and bar part
numbers, see page 25.
NOTE: The chain tension is correct when the gap
is 6.5 mm. Check the chain tension regularly, as
the chain stretches when it heats up.

17 17
6
7
CHAIN DRIVE
LINKS
BAR
GROOVE
5
9
8
10
FLATS
APPROX. 6.5 mm
NOTE: The chain tension is correct when the gap
is 6.5 mm. Check the chain tension regularly, as
the chain stretches when it heats up.

18
18
7.85~9.8 Nm (80~100 Kgf-cm)
12
click
13
11
INSTALLING AND REMOVING THE SCABBARD

19 19
7.85~9.8 Nm (80~100 Kgf-cm)
12
click
13
11
INSTALLING AND REMOVING THE SCABBARD

20
20
3
2
1
3
4
2
1
CLEANING THE PRODUCT
STORING THE PRODUCT
NOTE: Clean the the product with a with a soft-bristle
brush or with a soft, dry cloth.
NOTE: Do not use water to clean the product..