AEMC PEL 52 User manual

User Manual
ENGLISH
POWER & ENERGY LOGGER
WITH AEMC
®
INSTRUMENTS
Power & Energy Logger
Model PEL 52

Copyright©Chauvin Arnoux®, Inc. d.b.a. AEMC®Instruments. All rights reserved.
No part of this documentation may be reproduced in any form or by any means (including electronic
storage and retrieval or translation into any other language) without prior agreement and written consent
from Chauvin Arnoux®, Inc., as governed by United States and International copyright laws.
Chauvin Arnoux®, Inc. d.b.a. AEMC®Instruments
15 Faraday Drive • Dover, NH 03820 USA
Tel: [phone] or [phone] • Fax: [phone]
This documentation is provided “as is,” without warranty of any kind, express, implied, or otherwise.
Chauvin Arnoux®󰀨
but does not warrant the accuracy or completeness of the text, graphics, or other information contained
in this documentation. Chauvin Arnoux®, Inc. shall not be liable for any damages, special, indirect,


user of the documentation has been advised of the possibility of such damages.

Statement of Compliance
Chauvin Arnoux®, Inc. d.b.a. AEMC® Instruments

using standards and instruments traceable to
international standards.
We guarantee that at the time of shipping your
instrument has met the instrument's published

An NIST traceable certicate may be requested
at the time of purchase, or obtained by returning
the instrument to our repair and calibration
facility, for a nominal charge.
The recommended calibration interval for this
instrument is 12 months and begins on the date of
receipt by the customer. For recalibration, please
use our calibration services. Refer to our repair and
calibration section at www.aemc.com/calibration.
Serial #:
Catalog #: 2137.69 / 2137.71
Model #: PEL 52
ll in the appropriate date as indicated:
Date Received:
Date Calibration Due:
Chauvin Arnoux®, Inc.
d.b.a AEMC®Instruments
www.aemc.com

TABLE OF CONTENTS
1. INTRODUCTION.......................................................................7
1.1 PRECAUTIONS FOR USE.............................................................. 8
1.2 RECEIVING YOUR SHIPMENT..................................................... 8
1.3 ORDERING INFORMATION..........................................................11
1.3.1 Accessories.............................................................................11
1.3.2 Replacement Parts .................................................................11
1.4 CHARGING THE BATTERY ......................................................... 12
2. PRODUCT FEATURES ..........................................................13
2.1 DESCRIPTION............................................................................... 13
2.2 INSTRUMENT FRONT PANEL .................................................... 14
2.3 INSTRUMENT TERMINAL BLOCK ............................................. 14
2.4 INSTRUMENT REAR PANEL ...................................................... 15
2.5 SD CARD SLOT............................................................................. 15
2.6 MOUNTING.................................................................................... 16
2.7 BUTTON FUNCTIONS.................................................................. 16
2.8 LCD DISPLAY ................................................................................ 17
2.9 MEMORY CARD............................................................................ 19
3. SETUP .....................................................................................20
3.1 TURNING THE INSTRUMENT ON AND OFF ............................ 20
3.1.1 Turning On .............................................................................. 20
󰀨 .................................................................................. 20
󰀨 ............................................................................. 20
3.1.4 Battery Operation................................................................... 21
3.2 CONFIGURING THE INSTRUMENT........................................... 21
3.2.1 Network Type......................................................................... 21
3.2.2 Wi-Fi ...................................................................................... 22
3.2.3 Nominal Primary Current....................................................... 26
3.2.4 Aggregation Period................................................................ 27
3.2.5 Reset ..................................................................................... 27
3.3 REMOTE USER INTERFACE ...................................................... 28
3.4 INFORMATION.............................................................................. 30
4. OPERATION ...........................................................................32
4.1 DISTRIBUTION NETWORKS & CONNECTIONS OF THE PEL ...... 32
4.1.1 Single-Phase 2-wire: 1P-2W1I ............................................... 32
4.1.2 Single-Phase 3-wire 2-currents: 1P-3W2I ............................. 33
4.1.3 Two-Phase 3-wire (two-phase from a mid-tap transformer):
2P-3W2I.......................................................................................... 33

4.2 RECORDING ................................................................................. 34
4.3 MEASURED VALUE DISPLAY MODES...................................... 34
4.3.1 Measurement Mode ....................................................... 35
4.3.2 Energy Mode ................................................................. 37
4.3.3 Maximum Mode ............................................................ 38
5. PEL CONTROL PANEL - DATAVIEW®................................41
5.1 INSTALLING DATAVIEW®.............................................................41
5.2 PEL CONTROL PANEL ................................................................ 45
6. SPECIFICATIONS ..................................................................46
6.1 REFERENCE CONDITIONS ........................................................ 46
6.2 ELECTRICAL PROPERTIES........................................................ 46
6.2.1 Voltage Inputs ........................................................................ 46
6.2.2 Current Inputs........................................................................ 47
6.2.3 Intrinsic Uncertainty (Excluding Current Sensors) ................ 47
 ........................................... 47
6.2.4 Current Sensors .................................................................... 49
6.2.4.1 Precautions For Use................................................... 49
6.2.4.2 Characteristics ........................................................... 50
6.2.4.3 Intrinsic Uncertainty ................................................... 54
6.3 VARIATION IN THE FIELD OF USE............................................ 56
6.3.1 General .................................................................................. 56
6.3.2 Temperature .......................................................................... 56
6.3.3 Humidity................................................................................. 56
6.3.4 Continous Component........................................................... 56
6.3.5 Frequency.............................................................................. 56
6.3.6 Bandwidth.............................................................................. 57
6.3.7 Disturbed Signals .................................................................. 57
6.4 POWER SUPPLY........................................................................... 57
6.5 ENVIRONMENTAL CHARACTERISTICS................................... 58
6.6 Wi-Fi................................................................................................ 58
6.7 MECHANICAL CHARACTERISTICS .......................................... 58
6.8 ELECTRICAL SAFETY ................................................................. 59
6.9 ELECTROMAGNETIC COMPATIBILITY..................................... 59
6.10 RADIO EMISSION....................................................................... 59
6.11 M E M O R Y C A R D .......................................................................... 59

7. MAINTENANCE ......................................................................60
7.1 C L E A N I N G ...................................................................................... 60
7. 2 B AT T E R Y ........................................................................................ 60
7.3 UPDATING FIRMWARE................................................................ 61
7.4 REPAIR AND CALIBRATION ....................................................... 61
7.5 TECHNICAL AND SALES ASSISTANCE.................................... 62
7.6 L I M I T E D W A R R A N T Y ................................................................... 62
7.6.1 Warranty Repairs ................................................................... 63
8. APPENDIX ............................................................................. 64
8.1 MEASUREMENTS......................................................................... 64
 ................................................................................ 64
8.1.2 Sampling ................................................................................ 64
8.1.2.1 “1 s” (one second) Quantities ..................................... 64
8.1.2.2 Aggregation ................................................................ 65
8.1.2.3 Minimum and Maximum ............................................. 65
8.1.2.4 Calculation of Energies .............................................. 65
8.2 MEASUREMENT FORMULAS..................................................... 65
8.3 AGGREGATION............................................................................. 66
8.4 SUPPORTED ELECTRICAL NETWORKS ................................. 67
8.5 VALUES AVAILABLE .................................................................... 68
8.6 GLOSSARY.................................................................................... 70

Power & Energy Logger Model PEL 52 - User Manual 7
1. INTRODUCTION
Thank you for purchasing an AEMC®Instruments Power & Energy Logger
Model PEL 52.
For the best results from your instrument and for your safety, you must read the
enclosed operating instructions carefully and comply with the precautions for use.

Symbols & Denitions

CAUTION - Risk of Danger! Indicates a WARNING. Whenever this symbol
is present, the operator must refer to the user manual before operation
Indicates a risk of electric shock. The voltage at the parts marked with this
symbol may be dangerous
Indicates Important information to acknowledge
Magnet
SD Card
This product complies with the Low Voltage & Electromagnetic Compatibility
European directives (73/23/CEE & 89/336/CEE)
The 

Low-Voltage Safety, Electromagnetic Compatibility, and the Restriction of
Hazardous Substances.
The product has been declared recyclable
In the European Union, this product is subject to a separate collection
system for recycling electrical and electronic components in accordance with
directive WEEE 2002/96/EC
Chauvin Arnoux®and AEMC®Instruments have adopted an Eco-Design
approach in order to design this instrument. Analysis of the complete
󰀨
on the environment. In particular this instrument exceeds regulation
requirements with respect to recycling and reuse
Denition of Measurement Categories (CAT)
CAT IV corresponds to measurements performed at the primary electrical supply
(< 1000 V).
Example: primary overcurrent protection devices, ripple control units, and meters.
CAT III corresponds to measurements performed in the building installation at the
distribution level.
Example: hardwired equipment in xed installation and circuit breakers.
CAT II corresponds to measurements performed on circuits directly connected to
the electrical distribution system.
Example: measurements on household appliances and portable tools.

8 Power & Energy Logger Model PEL 52 - User Manual
1.1 PRECAUTIONS FOR USE
This device complies with safety standard IEC/EN 61010-2-30 or BS EN 61010-2-030.
The leads comply with IEC/EN 61010-031 or BS EN 61010-031. The current
sensors comply with IEC/EN 61010-2-032 or BS EN 61010-2-032 for voltages up
to 600 V in CAT III.

explosion, destruction of the device, or destruction of the installations.
■The operator and responsible authority must read and understand all
precautions needed before using the instrument. This instrument requires the
user to have knowledge and awareness of electrical hazards.
■Use only the supplied leads and accessories. If you use leads or accessories
with a lower voltage or category rating than the instrument, the combined
instrument, leads, and accessories are limited to the lower voltage or category
rating of the leads or accessories.
■Before each use, check the condition of the insulation on the leads, housing,
and accessories. Any items with a degree of deteriorated insulation must be
set aside to repair or discard.
■Do not use the instrument on networks where the voltage or category exceeds

■Do not use the instrument if it seems to be damaged, incomplete, or poorly
closed.
■When removing and inserting the SD card, the device must be disconnected
󰀨
■Use personal protection equipment when applicable.
■
physical guard.
■If the device is wet, dry it before use.
■All troubleshooting and calibration checks must be performed by competent,
accredited personnel.
1.2 RECEIVING YOUR SHIPMENT
Upon receiving your shipment, make sure that the contents are consistent with
the packing list. Notify your distributor of any missing items. If the equipment

distributor at once with a detailed description of any damage. Save the damaged
packing container to substantiate your claim.

Power & Energy Logger Model PEL 52 - User Manual 9
PRODUCT PACKAGING (2137.69)
Power & Energy Logger
PEL 52
Cat. #2137.69
(1) 4 GB USB Drive
with User Manual &
Dataview®Software
Also Included:
(1) Safety Sheet for the PEL
(1) Safety Sheet for the MiniFlex®Sensors
(1) Compliance Sheet
(1) SD Card
(1) Quick Start Guide
(2) AAA Rechargeable Batteries
(1) Battery Information Sheet
(2) MiniFlex®MA193-10-BK
Cat. #2140.48
Adapter for Power Cord
Cat. #5100.14
(1) USB SD Card Adapter
Cat. #5000.45
(12) Color-coded
ID Markers
Cat. #2140.45
(1) Power Cord,
5 ft 115 V
Cat. #5000.14
Soft Carrying Bag
Cat. #2126.71
(3) Black Leads &
Alligator Clips
Cat. #2140.44

10 Power & Energy Logger Model PEL 52 - User Manual
PRODUCT PACKAGING (2137.71)
Power & Energy Logger
PEL 52
Cat. #2137.71
(1) 4 GB USB Drive
with User Manual &
Dataview®Software
Adapter for Power Cord
Cat. #5100.14
(1) USB SD Card Adapter
Cat. #5000.45
(12) Color-coded
ID Markers
Cat. #2140.45
(1) Power Cord,
5 ft 115 V
Cat. #5000.14
Soft Carrying Bag
Cat. #2126.71
(3) Black Leads &
Alligator Clips
Cat. #2140.44
Also Included:
(1) Safety Sheet for the PEL
(1) Compliance Sheet
(1) SD Card
(1) Quick Start Guide
(2) AAA Rechargeable Batteries
(1) Battery Information Sheet