AERMEC WRC40 User manual

www.aermec.com
Translation from original
User manual
EN
■
WIRED PANEL
20.11 - 5385483_00
WRC40

ELECTRICAL DEVICES WARNINGS...........................................................................................................................................................................5
WIRED PANEL .................................................................................................................................................................................................................6
INSTALLING THE WIRED PANEL................................................................................................................................................................................7
USER INTERFACE ...........................................................................................................................................................................................................9
USER INTERFACE (DISPLAY) ................................................................................................................................................................................... 10
FUNCTIONS OF THE WIRED PANEL...................................................................................................................................................................... 11
SWITCHING THE UNIT ON / OFF ........................................................................................................................................................................... 11
SELECTING AN OPERATING MODE...................................................................................................................................................................... 11
SETTING THE OPERATING SETPOINT .................................................................................................................................................................. 12
SETTING THE VENTILATION SPEED...................................................................................................................................................................... 12
SETTING THE VERTICAL MOTORISED DISCHARGE FIN (UP&DOWN SWING) ........................................................................................ 13
SETTING THE HORIZONTAL MOTORISED DISCHARGE FIN (LEFT&RIGHT SWING) .............................................................................. 13
SETTING THE SYSTEM FUNCTIONS ..................................................................................................................................................................... 14
FUNCTIONS SYSTEM................................................................................................................................................................................................. 14
INDEPENDENT SWING OF THE MOTORISED DELIVERY FINS...................................................................................................................... 16
CONTROLLING THE OPENING OF THE FRONT PANEL OF THE UNIT......................................................................................................... 17
WI-FI FUNCTION......................................................................................................................................................................................................... 17
UNITS STATUS AND ALARM LOG.......................................................................................................................................................................... 18
SETTING OR DELETING A TIMED SWITCH-ON OR SWITCH-OFF (TIMER ON/TIMER OFF)..................................................................19
ONCE TIMER - SINGLE TIMED PROGRAMMING ............................................................................................................................................... 19
DAILY TIMER - DAILY TIMER PROGRAMMING................................................................................................................................................... 20
WEEKLY TIMER - WEEKLY TIMER PROGRAMMING .......................................................................................................................................... 21
TWO WEEK TIMER - FORTNIGHTLY TIMED PROGRAMMING....................................................................................................................... 22
COUNTDOWN TIMER ON ........................................................................................................................................................................................ 23
COUNTDOWN TIMER OFF....................................................................................................................................................................................... 23
SET CLOCK OF THE SYSTEM................................................................................................................................................................................... 24
SETTING A SYSTEM LOCK ....................................................................................................................................................................................... 25
FUNCTIONS RELATING TO THE SYSTEM MENU............................................................................................................................................... 26
THE SYSTEM MENU................................................................................................................................................................................................... 26
VIEWING THE ALARM LOG...................................................................................................................................................................................... 26
SETTING THE INDOOR UNIT ADDRESS............................................................................................................................................................... 26
VIEWING THE OPERATING PARAMETERS........................................................................................................................................................... 26
FUNCTIONS OF THE DEBUG MENU..................................................................................................................................................................... 26
SETTING THE AMBIENT PROBE TO BE USED..................................................................................................................................................... 27
SETTING THE ROOM TEMPERATURE CORRECTION........................................................................................................................................ 27
ACTIVATING/DEACTIVATING THE ANTI-FREEZE ALARM .............................................................................................................................. 27
SETTING THE USEFUL HEAD FOR THE FANS OF DUCT TYPE INDOOR UNITS ....................................................................................... 27
SETTING THE FUNCTION FOR REFRIGERANT LEAKAGE PROTECTION.................................................................................................... 27
SETTING THE VENTILATION MODE AFTER THE SET-POINT HAS BEEN REACHED................................................................................ 28
SETTING THE CONTROL MODE FOR THE COMPRESSOR HEATER ............................................................................................................. 28
ENABLING OR DISABLING THE ECD ACCESSORY ........................................................................................................................................... 28
FUNCTION NOT AVAILABLE ................................................................................................................................................................................... 28
ALARM CODES............................................................................................................................................................................................................ 29
SUMMARY

All specifications are subject to change without prior notice. Although every effort has been made to
ensure accuracy, Aermec shall not be held liable for any errors or omissions.
Dear customer,
Thank you for choosing an AERMEC product. It is the fruit of many years of experience and special
design studies and has been made of the highest grade materials and with cutting edge technology.
In addition, all our products bear the EC mark indicating that they meet the requirements of the
European Machine Directive regarding safety. The quality level is being constantly monitored, so
AERMEC products are synonymous with Safety, Quality and Reliability.
The data may undergo modifications considered necessary for the improvement of the
product, at any time and without the obligation for any notice thereof.
Thank you once again.
AERMEC S.p.A
This marking indicates that this product should not be disposed with other household
wastes throughout the EU.
To prevent possible harm to the environment or human health from uncontrolled disposal
of Waste Electrical and Electronic Equipment (WEEE), please return the device using
appropriate collection systems, or contact the retailer where the product was purchased.
Please contact your local authority for further details.
Illegal dumping of the product by the user entails the application of administrative
sanctions provided by law
INFORMATION FOR USER
This device is universal.
By pressing a key for a function that is not available, the unit will not change the operating status.
Never install the device in a damp area and do not expose it to direct sunlight.
Do not bump, throw or disassemble the device frequently.
Never use the device with wet hands.
Carefully read the manual before using and installing the device.

GENERAL WARNINGS
• Read carefully these general safety precautions
before installing the air conditioning devices
and ensure that the installation is performed
correctly.
• Failure to observe these instructions can cause
damages to property or people's injuries, which
may b e serious depending on the circumstances.
• Aermec will in no case be liable for any damages
to property and/or persons caused by improper
operations such as: incorrect installations,
debugging or maintenance not carried out,
non-compliance with the installation regulations
foreseen in the country where the device will
be installed or non-compliance with the rules
contained in this manual.
• Refer to the national regulations for the
installation: the device must be installed in
compliance with national plant engineering rules.
WARNINGS FOR THE USER
• The use of the device is not recommended to
people (children included) with reduced physical,
sensorial or mental capacity, as well as operators
without experience and knowledge, except in
the presence of a safety operator who is able to
ensure the supervision and provide the adequate
use instructions. Do not allow children to play
with the device.
• All illustrations and information contained in this
manual are purely indicative; for the effective
control of the functions related to the device,
refer to that which appears on the controller's
display (if present).
• In order to improve the product, we reserve the
right to modify or revise this document without
prior notice; therefore remember to periodically
verify the presence of new versions.
• To prevent electric shock or fire accidents:
1. Do not operate the air conditioner with wet
hands.
2. Do not disassemble the device or remove its
internal
3. parts.
4. Do not modify or repair the air conditioner by
yourself.
5. Do not move or re-install the device by yourself.
6. Do not use flammable materials near the device.
• To clean the device, do not use organic solvents,
such as paint thinners. Possible result: damages,
electric shock or fire accidents.
WARNINGS FOR THE INSTALLER
• This device cannot be used on its own. Also refer
to the user manuals of the outdoor/indoor unit.
• The installation and electrical connections
of the unit must be carried out only by
persons possessing the technical-professional
requirements for installation, transformation,
expansion and maintenance of systems and the
ability to perform checks on them for safety and
operation. In this manual, these will generally be
referred to as “Personnel with specific technical
skills”.
• The incorrect installation or assembly of the
device could cause electrocution, short-circuits,
losses and fire accidents.
• Use exclusively optional devices and spare parts
approved by Aermec.
• Ensure that the electrical power supply complies
with the parameters included in this manual.
A power supply that is different from the
recommended one can cause damage.
• Ensure that all connections are performed
according to the instructions in this
manual. Incorrect connections could cause
communication malfunctioning.
• Ensure to be able to use the correct
communication ports, otherwise the connection
may not work properly.
• The connected communication line must
be protected with electrical tape to prevent
oxidation and short-circuits.
WARNING:
Do not install the device in a location where it
could be affected by inflammable gas leaks or
deposits of materials which are inflammable,
explosive, poisonous, corrosive or hazardous
substances. Risk of fire or explosion. Install
the unit in a location with minimal levels of
dust, fumes, humidity in the air, corrosive
agents and not exposed to direct sunlight
and adverse weather conditions.
5
ELECTRICAL DEVICES WARNINGS

6
WIRED PANEL
The wired panel (accessory) allows the rapid setting
of the unit operating parameters and their display.
The panel can memorise all the settings, and use
them when it starts up again automatically after a
power failure.
The user interface has an LCD display with simple
icons giving information and showing the available
functions on the units; the user can interact with the
panel using the function keys located in the lower
part of the panel itself.
ACCESSORY KIT QUANTITY DESCRIPTION
1 Wired panel
3 Fixing screws ST3.9x25 MA
2Fixing screws M4x25
1Recessed box

7
INSTALLING THE WIRED PANEL
DIMENSIONS OF THE WIRED PANEL:
112
112
22
106,5
48
106,5
30 30
24
[mm]

8
Notes for installing the wired panel.
It’s important to respect the following indications:
1. Before beginning, make sure the indoor unit is
not electrically powered.
2. Before installing the panel, pass the serial
communication cable through the specific
trunking, as far as the flush-mounting box.
3. Fix the panel to the flush-mounting box using the
screws supplied.
WARNING:
• To avoid electromagnetic disturbance,
remember to keep the serial communication
line separate from the unit power line
(minimum distance 20 cm).
• Use a shielded-conductor cable for the serial
line, to avoid the risk of disturbance.

9
USER INTERFACE
Icon Function
1
Sets fan speed
2
Used to increase or decrease the
selected data item, or move to the
previous/next item
3
4
Used to switch the indoor unit on or off,
or to return to the previous level when
scrolling through the menus
5
Sets the operating mode for the unit
6
Used to activate or deactivate a
function, or to move from one
parameter to another
7
8
Used to confirm the parameter settings
or access the selection menus
9
Sets automatic delivery fin swing
1 2 48
9 3 67 5

10
Icon Function
The VERTICAL SWING function is active
The HORIZONTAL SWING function is
active
NOT AVAILABLE
The night-time comfort program is
active
AUTOMATIC mode is active
COOLING mode is active
DEHUMIDIFICATION mode is active
VENTILATION ONLY mode is active
HEATING mode is active
The air ioniser is active
Indicates that the I-DEMAND function
is active
The anti-freeze function is active
A panel lock has been activated
USER INTERFACE DISPLAY
Icon Function
Indicates the current fan speed setting
Indicates that the settings are saved on
the wired panel memory
The energy-saving function is active
The prolonged ventilation function is
active (X-FAN)
The air filter in the indoor unit must be
cleaned
Indicates any hourly settings that may
be active
FUNCTION NOT AVAILABLE
The "quiet operation" function has been
enabled
Indicates the total locking of all the
functions
Indicates that the WI-FI function was
activated
Indicates that the control function
independent of the air delivery fins is
active
Indicates that a minimum and/or
maximum temperature value is set
FUNCTION NOT AVAILABLE
DRED Status
DRED Status
DRED Status

11
FUNCTIONS OF THE WIRED PANEL
To switch the indoor unit managed via the wired
panel on or off, press the key
MENU/OK
FAN ON/OFF
MODE
SWING
.
Auto
Cooling
Dehumidication
Ventilation Only
Heating
Selecting an operating mode
SWITCHING THE UNIT ON / OFFSwitching the unit on/off
To modify the operating mode of the indoor unit
managed via the wired panel, just press the
MENU/OK
FAN ON/OFF
MODE
SWING
key;
every time it is pressed, the unit will switch from one
mode to the next.
The possible modes are:
• Auto ( ): this function automatically selects the
most suitable operating mode based on the indoor
temperature. The set-point cannot be altered, but
ventilation and other functions such as “swing” can
be set as normal (WARNING: this mode cannot be
selected if the SAVE function is active).
• Cooling ( ): this mode cools the ambient air
until the temperature chosen as the operating set-
point is reached; this temperature may be between
16 °C and 30 °C.
• Dehumidification ( ): in a similar way to cooling
mode, this function dehumidifies the ambient air;
the operating temperature may be between 16 °C
and 30 °C.
• Ventilation Only ( ): the set-point cannot be
altered because the ambient air is not being either
cooled or heated, but ventilation and the swing
function can be set as normal.
• Heating ( ): this mode heats the ambient air
until the temperature chosen as the operating set-
point is reached; this temperature may be between
16 °C and 30 °C.
SELECTING AN OPERATING MODE

12
All the operating modes (except the automatic one)
require an room air temperature value to control to:
this is called the operating set-point.
If the unit is on (and the automatic mode is not
selected), just press the
MENU/OK
FAN ON/OFF
MODE
SWING
or
MENU/OK
FAN ON/OFF
MODE
SWING
arrow keys to
decrease or increase the operating setting by 1 °C. A
long press will increase or decrease the value by 1 °C
every 0.3 seconds.
Press the button
MENU/OK
FAN
ON/OFF
MODE
SWING
to modify the fan speed. In the
DRY mode operation (dehumidification), the fan will
automatically change to the minimum speed..
SETTING THE OPERATING SETPOINT
Operating set point
Setting the ventilation speed
SETTING THE VENTILATION SPEED
MINIMUM speed
LOW-MEDIUM speed
TURBO speed
AUTOMATIC speed
TURBO
AUTO
MEDIUM speed
MEDIUM-HIGH speed
HIGH speed

13
SETTING THE VERTICAL MOTORISED
DISCHARGE FIN UP&DOWN SWING
SETTING THE HORIZONTAL MOTORISED
DISCHARGE FIN LEFT&RIGHT SWING
Setting the swing
If the unit is on, while pressing the button
MENU/OK
FAN ON/OFF
MODE
SWING
it
activates the swing of the motorized supply air fin
(UP&DOWN). The fin allows to change the air flow in
the room depending on the set position; the logic
where this function is managed:
When the unit is on, while pressing the button it’s
possible to set one by one the following steps:
SWING
disabled
SWING
disabled
If the unit is on, while pressing the button
MENU/OK
FAN ON/OFF
MODE
SWING
it
activates the swing of the motorized supply air fin
(LEFT&RIGHT). The fin allows to change the air flow
in the room depending on the set position; the logic
where this function is managed:
When the unit is on, while pressing the button it’s
possible to set one by one the following steps:

14
SETTING THE SYSTEM FUNCTIONS
Accessing the settings menu
Setting the system functions
Press the
MENU/OK
FAN ON/OFF
MODE
SWING
button to access the main menu
where the functions are grouped into sub-menus,
each represented by a different icon.
To access timer programming, proceed as follows:
• Press
MENU/OK
FAN ON/OFF
MODE
SWING
to access the functions menu.
• Use the
MENU/OK
FAN ON/OFF
MODE
SWING
or
MENU/OK
FAN ON/OFF
MODE
SWING
button to select the FUNCTION
icon and enter the functions menu.
• Select the required function using the
MENU/OK
FAN ON/OFF
MODE
SWING
or
MENU/OK
FAN ON/OFF
MODE
SWING
button.
• To activate or deactivate the functions, press the
MENU/OK
FAN ON/OFF
MODE
SWING
or
MENU/OK
FAN ON/OFF
MODE
SWING
button. If the selected function offers this
option, press
MENU/OK
FAN ON/OFF
MODE
SWING
to access the sub-menu.
FUNCTIONS SYSTEM
FUNCTION NOT AVAILABLE.
The SLEEP function enable or disable night-time
operation The operating setting and fan speed are
calculated automatically to ensure the best night-
time comfort.
In cooling or dehumidification: the temperature
set is gradually increased to guarantee maximum
comfort combined with energy saving.
In heating: the temperature set is gradually
decreased to guarantee maximum comfort
combined with energy saving.
The SLEEP function is automatically cancelled if
the operating mode is changed, or if the unit is
switched off.
FRESH AIR FUNCTION
SLEEP  THE NIGHT WELLNESS FUNCTION

15
The HEALTH function enable or disable the air
purifier Cold Plasma function capable of reducing
pollutants breaking down their molecules using
electric discharges, causing the splitting of the
water molecules in the air into positive and negative
ions. These ions neutralise the molecules of the
gaseous pollutants obtaining products that are
normally present in clean air. The device is able to
eliminate 90% of the bacteria. The result is clean,
ionised air that has no bad odours.
FUNCTION NOT AVAILABLE.
HEALTH  AIR PURIFIER COLD PLASMA
AUXILIARY HEATING
When this function (only available in cooling mode)
is activated, the unit works in energy saving mode.
When the I-DEMAND function is active, the unit fan
speed is determined automatically. This function
cannot be activated at the same time as the SLEEP
function.
IDEMAND FUNCTION
The HOLIDAY function enable or disable antifreeze
function, only available in heating mode, makes it
possible to keep an operation setpoint in heating
mode equivalent to 8 °C, ensuring thus that
the room temperature does not go below this
threshold.
This function is automatically disabled if any other
mode than heating is set. This function cannot be
activated at the same time as the SLEEP function.
MEMORY is a function that allows the automatic
saving of the working set-point used. Following
an accidental interruption of the power supply for
example, the unit will automatically adopt the last
working set-point imposed.
The SAVE function is used to set a minimum
temperature limit for cooling and dehumidifica-
tion modes, and a maximum temperature limit for
heating mode. This allows the unit to work within a
temperature range that guarantees energy savings.
After selecting the SAVE function, use the
MENU/OK
FAN ON/OFF
MODE
SWING
or
MENU/OK
FAN ON/OFF
MODE
SWING
button to choose whether to set the cooling or
heating limit. To set the required value, use the
MENU/OK
FAN ON/OFF
MODE
SWING
or
MENU/OK
FAN ON/OFF
MODE
SWING
button.
HOLIDAY  ANTIFREEZE FUNCTION
MEMORY FUNCTION
SAVE
The DRY function enable the X-FAN function. Dur-
ing the operation in cooling or dehumidification
mode the condensate caused by the humidity in the
air is formed on the heat exchanger within the unit.
The X-FAN function allows, when the air conditioner
is off, to perfectly dry the coil and avoid the forma-
tion and proliferation of pathogens.
The FILTER CLEAN function is used to define
the time that must elapse before a filter cleaning
reminder is given.
After selecting the function and entering the
relative sub-menu, use the
MENU/OK
FAN ON/OFF
MODE
SWING
or
MENU/OK
FAN ON/OFF
MODE
SWING
button to
select one of the three filter duration levels:
Level 1 = lifespan 5500~10000 hours
Level 2 = lifespan 1400~5000 hours
Level 3 = lifespan 100~1000 hours
After selecting the required level, the
MENU/OK
FAN ON/OFF
MODE
SWING
or
MENU/OK
FAN ON/OFF
MODE
SWING
button
can be used to set the number of hours that must
elapse before the filter cleaning reminder is given.
Each level has hour steps:
Level 1 = 500-hour steps
Level 2 = 400-hour steps
Level 3 = 100-hour steps
Press
MENU/OK
FAN ON/OFF
MODE
SWING
to save the settings.
Every time this function is deactivated, the unit
operating time will be reset.
DRY  XFAN FUNCTION
FILTER CLEAN  FILTER CLEANING REMINDER

16
The QUIET function (available in cooling, heating
and automatic mode) activates or deactivates quiet
operation to reduce the noise level of the indoor
unit and deactivate acoustic feedback. By activating the INDEPENDENT SWING function,
the four air delivery outlets of the unit can be inde-
pendently controlled.
When the unit is switched on and the function has
been selected, enter the relative sub-menu and
choose one of the following options:
Set independent swing
Reset independent swing
List of independent swing options
Set independent swing
From the swing settings menu, use the
MENU/OK
FAN ON/OFF
MODE
SWING
or
MENU/OK
FAN ON/OFF
MODE
SWING
button to select the AIR PORT you want to control
(the number 0 corresponds to the number of rings
at the air outlet on the panel, so you can see which
outlet is being controlled), then press
MENU/OK
FAN ON/OFF
MODE
SWING
or
MENU/OK
FAN ON/OFF
MODE
SWING
to
activate or deactivate independent swing for the air
outlet selected.
Press
MENU/OK
FAN ON/OFF
MODE
SWING
to define which mode the swing of the
motorised delivery fins should work in. The swing
follows this sequence:
The LOW DRY TEMPERATURE defines the set-point
used in dehumidification mode as 12 °C.
The function will be automatically deactivated if the
operating set-point is manually modified while the
unit is working in dehumidification mode.
The SETBACK function allows the unit to carry on
working even after switch-off, to ensure that the
predefined working set-point is reached.
After entering the sub-menu of the SETBACK
function, use the
MENU/OK
FAN ON/OFF
MODE
SWING
or
MENU/OK
FAN ON/OFF
MODE
SWING
button to select the
required temperature limit. Now set the limit using
the
MENU/OK
FAN ON/OFF
MODE
SWING
or
MENU/OK
FAN ON/OFF
MODE
SWING
button.
The control panel can display the temperature
values in °C or °F. To change the measurement unit,
activate or deactivate the FAHRENHEIT function.
With this function enabled, the motorised air
delivery fin can shift from standard swing to fixed
angle swing, to meet any requirement and ensure
optimum comfort in the room.
QUIET FUNCTION INDEPENDENT SWING OF THE MOTORISED
DELIVERY FINS
LOW DRY TEMPERATURE FUNCTION
SETBACK FUNCTION
FAHRENHEIT FUNCTION  SETTING THE UNIT OF
MEASUREMENT
FIXED ANGLE SWING
NOTE:
If this function is not available for the unit
being used, it will be cancelled automatically
after setting.
SWING
disabled
Reset independent swing
From the swing reset menu, use the
MENU/OK
FAN ON/OFF
MODE
SWING
or
MENU/OK
FAN ON/OFF
MODE
SWING
button to
select RESET. To confirm, press
MENU/OK
FAN ON/OFF
MODE
SWING
.
List of independent swing options
From this sub-menu, you can see the independent
swing activation or deactivation status for each air
outlet on the unit.
NB:
• Only vertical swing (UP&DOWN SWING) is
compatible with this function.
• For the independent swing function to
work, only one of the four air outlets on
the unit can be closed.
• If the independent swing function is
deactivated, the previously defined swing
setting will be restored.
NB:
Function only available for LGC_CS versions.

17
With this function, the front panel of the unit can
be automatically opened to make it easier to clean
the filter.
With the unit switched on, enter the sub-menu
of the function and press the
MENU/OK
FAN ON/OFF
MODE
SWING
or
MENU/OK
FAN ON/OFF
MODE
SWING
button to
control the up and down movement of the panel.
Press the
MENU/OK
FAN ON/OFF
MODE
SWING
button to bring the panel back to
its proper operating position. During this process,
the message RESET WINDOW will appear on the
control panel; the HOME page will be automatically
restored when the operation has ended.
CONTROLLING THE OPENING OF THE
FRONT PANEL OF THE UNIT
After entering the WI-FI function menu, press the
MENU/OK
FAN ON/OFF
MODE
SWING
or
MENU/OK
FAN ON/OFF
MODE
SWING
button to activate or deactivate the WI-FI
device installed in the indoor unit.
To reset the WI-FI module, press the
MENU/OK
FAN ON/OFF
MODE
SWING
or
MENU/OK
FAN ON/OFF
MODE
SWING
button
and select RESET, then press
MENU/OK
FAN ON/OFF
MODE
SWING
to confirm.
WIFI FUNCTION

18
WARNING:
If there are several simultaneous errors on
the system, press the
MENU/OK
FAN ON/OFF
MODE
SWING
or
MENU/OK
FAN ON/OFF
MODE
SWING
, key to scroll
through them. Each error has its own unique
identication code. For more information
about the error codes, refer to the relevant
table at the end of this manual.
Viewing the unit status and the alarm log
UNITS STATUS AND ALARM LOG
From the main control panel menu, select the
SEARCH icon and then press
MENU/OK
FAN ON/OFF
MODE
SWING
to access the
required menu.
Use the
MENU/OK
FAN ON/OFF
MODE
SWING
or
MENU/OK
FAN ON/OFF
MODE
SWING
button to select the item you
want to see, then press
MENU/OK
FAN ON/OFF
MODE
SWING
to confirm. The
available items are:
UNITS STATUS: for viewing various info items
relating to the unit, such as:
• Defrost cycle in progress
• The time left before the indoor unit air filter must
be cleaned
• The outside air temperature
• The room air temperature measured
ERROR INFORMATION:to view the code of the
current alarm.
To quit the sub-menu and return to the previous
levels, press
MENU/OK
FAN ON/OFF
MODE
SWING
.

19
Timer programming
Single timer programming
SETTING OR DELETING A TIMED SWITCH
ON OR SWITCHOFF TIMER ON/TIMER
OFF
From the main menu of the control panel, select the
TIMER icon and then press
MENU/OK
FAN ON/OFF
MODE
SWING
to access the
required menu.
Use the
MENU/OK
FAN ON/OFF
MODE
SWING
or
MENU/OK
FAN ON/OFF
MODE
SWING
button to select the item you
want to see, then press
MENU/OK
FAN ON/OFF
MODE
SWING
to confirm.
Use the
MENU/OK
FAN ON/OFF
MODE
SWING
or
MENU/OK
FAN ON/OFF
MODE
SWING
button to activate or deactivate the
required timer.
The available items are:
ONCE: programming of a single timer
DAILY: programming of a daily timer
WEEKLY: programming of a weekly timer
TWO WEEK: programming of a fortnightly timer
TIMER ON: switch-on programmed
TIMER OFF: switch-off programmed
To quit the sub-menu and return to the previous
levels, press
MENU/OK
FAN ON/OFF
MODE
SWING
.
ONCE TIMER  SINGLE TIMED
PROGRAMMING
With single timed programming, the unit can be
switched on or off at a specific time (if the unit
is ON, switch-off is set; if the unit is in standby,
timed programming refers to switch-on). Once the
switch-on or switch-off has been implemented, the
function is automatically disabled.
To set single programming, access the ONCE menu
using the
MENU/OK
FAN ON/OFF
MODE
SWING
or
MENU/OK
FAN ON/OFF
MODE
SWING
button and select the value you
want to change (hours or minutes). Use the
MENU/OK
FAN ON/OFF
MODE
SWING
or
MENU/OK
FAN ON/OFF
MODE
SWING
button to set the required value for the number
selected (the value being defined is shown in black).
Press
MENU/OK
FAN ON/OFF
MODE
SWING
to save the timer.
To quit the sub-menu and return to the previous
levels, press
MENU/OK
FAN ON/OFF
MODE
SWING
.

20
Daily timer programming
DAILY TIMER  DAILY TIMER
PROGRAMMING
With daily timed programming, up to 8 actions can
be programmed (timed switch-on or switch-off
operations) over a 24-hour period, thereby creating
daily time bands.
To set daily timed programming, enter the DAILY
menu and use the
MENU/OK
FAN ON/OFF
MODE
SWING
or
MENU/OK
FAN ON/OFF
MODE
SWING
button to select the value
you want to change (when the last value on the
right has been reached, the cursor will automatically
move onto the next line). The values to be set for
this function are:
SCH: indicates the number and status (ON - active,
OFF - not active) of the selected action.
TIME: indicates the time when the selected action
must be implemented.
OnOFF: indicates the command (ON activates the
unit, OFF deactivates it) associated with the selected
action.
COOL: indicates the cooling setting to be assigned
if necessary during the implementation of the
selected action (if the command of the action itself
requires unit switch-on).
HEAT: indicates the heating setting to be assigned
if necessary during the implementation of the
selected action (if the command of the action itself
requires unit switch-on).
Use the
MENU/OK
FAN ON/OFF
MODE
SWING
or
MENU/OK
FAN ON/OFF
MODE
SWING
button to define the required
setting for the selected value (the value being
defined is shown in black).
Press
MENU/OK
FAN ON/OFF
MODE
SWING
to save the settings.
To quit the sub-menu and return to the previous
levels, press
MENU/OK
FAN ON/OFF
MODE
SWING
.