aFe Power 51-82722 User manual

advanced FLOW engineering
Instruction Manual P/N: 51-82722 / 54-82722
Make: Toyota Model: Tacoma Year: 2005-2015 Engine: L4-2.7L

Label Qty. Description Part Number
A1 1 Air Filter (Pro Dry, Gray Media) 21-91021
A2 1 Air Filter (Pro 5R, Blue Media) 24-91021
B 1 Housing 05-00823
C 1 Adaptor, filter 05-00611
D 9 Screw, Btn Hd Socket M6 x 1 x 10 03-50113
E 1 Hose, Vacuum (9") 05-00122
F 1 Tube 05-82722B1
G 1 Coupling 2.75 x 3 05-00418
H 1 Coupling 4 x 2.75 x 3.5 05-00649
I 1 Clamp #064 03-50006
J 3 Clamp #048 03-50007
K 2 Screw, M4 x .7 x 16 Cheese Hd 03-50030
L 1 Isolation Mount 03-50063
M 1 Washer, flat 03-50065
N 1 Nut, Hex: M8, Zn Plt 03-50087
O 1 Nipple 03-50191
P 1 Cover 05C00823B
Q 1 Bracket 05-00744
R 1 Plug, Airbox 05-00937B
Note: Legal in California for use on race vehicles only. The use of this device on vehicles used on public streets or high-
ways is strictly prohibited in California and others states that have adopted California
emission regulations.
• Please read the entire instruction manual before proceeding.
• Ensure all components listed are present.
• If you are missing any of the components, call customer support at 951-493-7100.
• Ensure you have all necessary tools before proceeding.
• Do not attempt to work on your vehicle when the engine is hot.
• Disconnect the negative battery terminal before proceeding.
• Retain factory parts for future use.
Page 2
Tools needed: 4mm allen wrench, 8 mm nut driver, 10 mm socket w/extension and
ratchet, 12 mm socket w/extension and ratchet, 13 mm
socket w/extension and ratchet, 10 mm wrench, 13mm
wrench, Phillip screw driver, and Flathead screw driver.

aFepower.com
Page 3
A1
B
C
E
F
A2
P
O
M
L
HG
J
I
N
D K
R
Q

Refer to Figure A for Steps 1-3
Step 1: Remove the three bolts that secure the intake resonator to the valve cover 1 .
Loosen the intake hose clamps 2 .
Step 2: Remove the intake hose.
Step 3: Remove MAF sensor 3 from OE airbox using phillips screwdriver.
REMOVAL
Page 4
1
22
3
Figure A

Refer to Figure C for Steps 4-5
Step 4: Disconnect the breather hose 4 and the vacuum hose 5 connected to the fuel
regulator, going to the intake resonator. Loosen the clamp on the throttle body.
Step 5: Remove the VSV located 6 on the back side of the intake resonator and remove intake
resonator. (Save OE bolts for later use)
Figure C
REMOVAL
Page 5
aFepower.com
4
6
5

Refer to Figure B for Steps 5-6
Step 5: Remove the three 12mm bolts securing the lower airbox.
(Set two bolts aside for later use) Remove the lower airbox.
Step 6: Remove 2 OE rubber grommets and spacers from lower airbox. (Set aside for later use)
Page 6
REMOVAL
Figure B

Refer to Figure D for Steps 7-8
Step 7: Transfer MAF sensor to aFe intake tube with hardware provided using flathead screwdriver.
Step 8: Install brass vacuum hose fitting onto aFe intake tube.
Figure D
INSTALL
aFepower.com
Page 7

Refer to Figure E for Step 9
Page 8
Figure E
7
INSTALL
Step 9: Place the “L” bracket on the valve cover 7 . Secure with OE bolt from intake resonator.
Secure the VSV with the supplied nuts and OE bolts.

Step 10: With OE rubber grommets removed form OE lower airbox, place onto new housing
with metal spacers 8 .
aFepower.com
Page 9
Refer to Figure F for Step 10
Figure F
INSTALL
8
8

Refer to Figure G for Step 11
Step 11: Insert M8 isolation mount 9 and hand tighten firmly. ( It may be necessary to
clean the threads from undercoating or paint)
Figure G
Page 10
INSTALL
9