aFe Power 57-10018D User manual

Cold Air Intake System
Instruction Manual P/N: 57-10018D / 57-10018R_____________________________
Make: Chevrolet Model: Camaro ZL1 Year: 2017-2023Engine: V8-6.2L (sc) LT4

Page 2
• Please read the entire instruction manual before proceeding.
• Ensure all components listed are present.
• For technical support please call 951-493-7185.
• Ensure you have all necessary tools before proceeding.
• Do not attempt to work on your vehicle when the engine is hot.
• Retain factory parts for future use.
Label
Qty.
Description
Part Number
A1
1
Air Filter (Pro 5R)
24-90112
A2
1
Air Filter (Pro DRY S)
21-90112
B
1
Tube
05-5710018C1
C
1
Housing
05-5710018B2
D
1
Scoop
05-74210B3
E
1
Coupling, Silicone Bellow
05-01605
F
1
Fitting, SAE 9.89 to 1/8" NPT
05-01692
G
2
Clamp, T-bolt (3-13/16" - 4-1/8") (SS)
03-50265
H
1
Seal, Trim: 13/32" dbl. Bulb (32"L)
05-01534
J
2
Screw, Torx: M4x8mm
03-50491
Installation will require the following tools:
T-20 Torx driver, 8mm nut driver, 11mm deep socket & driver, 15mm wrench or adjustable wrench
Warranty Information available at https://afepower.com/contact#warranty
Emissions Disclaimer: This product is not currently CARB exempt and is not available for purchase in
California or for use on any vehicle registered with the California Department of Motor Vehicles.

Page 3

Page 4
Refer to Figure A for Steps 1-4
Step 1: Disconnect the mass air flow sensor 1 and the wiring harness clip 2 .
Step 2: Disconnect the breather hose 3 from the intake tube.
Step 3: Use an 8mm nut driver to loosen the stock clamps 4 at the throttle body and the airbox.
Step 4: Remove the stock intake tube.
REMOVAL
Figure A
1
3
4
2

Page 5
Refer to Figure B for Steps 5-6
Step 5: Remove the clip 5 holding the coolant line to the airbox.
Step 6: Remove the airbox by pulling up to release from its mounting grommets 6 . Make sure the
mounting grommets are still in the chassis mounting tabs. If they pulled out and are stuck in the lower
half of the airbox, remove them from the airbox and insert them back on the chassis mounting tabs.
3
REMOVAL
Figure B
6
5

Page 6
Refer to Figure C for Steps 7-8
Step 7: Using a Torx T20 driver, remove the mass air flow sensor 7 from the upper half of the airbox and
install it into the aFe POWER intake tube using the two provided M4 torx screws.
Step 8: Install the supplied aluminum vent fitting 8 into the aFe intake tube using a 15mm wrench or
adjustable wrench.
7
INSTALL
Figure C
8
7

Page 7
Refer to Figure D for Steps 9-11
Step 9: Install the supplied air inlet scoop 9 into the aFe POWER housing.
Step 10: Install the aFe POWER housing assembly into the vehicle by pushing down the housing pins into
the mounting grommets. Make sure the pins are completely through the mounting grommets and the
scoop is in the rubber inlet opening cavity.
Step 11: Install the seal trim 10 on the top opening of the aFe POWER housing as shown. Trim to fit.
Figure D
9
10
INSTALL

Page 8
Refer to Figure E for Step 12
Step 12: Remove the filter clamp 11 from the aFe POWER filter. Slide the aFe POWER filter into the aFe
POWER housing from the top. Then guide the filter flange through the oval opening in the housing and
snap in the filter. Place the filter clamp on the filter flange.
11
INSTALL
Figure E

Page 9
Refer to Figure F for Steps 13-14
Step 13: Install the supplied silicone coupling 12 onto the throttle body with the supplied clamp 13 as shown
and tighten the clamp using an 11mm deep socket and driver.
Step 14: Place the other supplied clamp 14 on the silicone coupling as shown. Do not tighten this clamp.
INSTALL
Figure F
14
16
12
13

Page 10
Refer to Figure G for Steps 15-16
Step 15: Install the aFe POWER intake tube into the vehicle. Slide the tube into the throttle body coupling
first, then into the air filter.
Step 16: Align the aFe POWER intake tube and clamps correctly, then using a 11mm deep socket and
driver tighten all the clamps.
INSTALL
Figure G