Afinia 3D H400+ User manual

Download full user manual at www.afinia.com/support

400+
400+
Phone Support: 952-279-2643

Afinia 3D
8150 Mallory Court, PO BOX 846
Chanhassen, MN 55317
youtube.com/afinia3dprint
Support: [email protected] Web: www.afinia.com

Unpacking
Install Printer
Install Software
Load Filament
Network Setup
Load and Print Model
1
2
3
4\5
6
7


After unboxing the machine, remove the cushions inside the printer.
Unpacking
Open the front door and remove the top lids. Find the print head in the
accessory box.
WARNING: This 3D Printer - when used with styrene
filament (ABS / HIPS / PC-ABS) - can expose you and
others in the same room to styrene, a chemical known
to the State of California to cause cancer.
www.P65Warnings.ca.gov
ALWAYS OPERATE THIS PRODUCT IN A
WELL-VENTILATED AREA.



1.
and install it on your computer.
Afinia 3D

Studio Software
Please go to www.afinia.com/support/downloads to download the Studio software
Install Printer
Connect the printer to your
computer.
Detect your nozzle height.
a. Click the Initialize button to initialize the printer.
b. Click the Calibrate button.
c. Click the Auto button to begin auto nozzle height
detection.
Align the extruder mount to the
extruder mount slots, then press
down on the extruder until it
locks into position.
Install the FFC cable
as shown above.
The extruder needs to
be pressed down to the
bottom of the mount.
Notice: When installed correctly,
should be at the same level.
the red and blue shaded parts

6\
the printer will beep and start extruding
8\ Close the top covers and doors.
9\ Please note that the external spool holder
printing performance.
7\
Guiding tube
Filament
extrusion
Top View
Insert guiding
tube into the
entrance
lock the guidng tube at the
tube holder
5
10cm
20cm
10cm

Gently push the filament into the
filament entrance and down until it stops.
After reaching the print temperature,
filament.
Push the guiding tube into the filament
entrance and insert the tube into the holding
clip on the mount.
filament
can only be placed at the following positions.
other locations could adversely affect printing
guiding tube.
Put filament into the external
spool holder and insert filament into the

door.
the machine through the hole on the back
Insert filament and guiding tube into
Make sure the
section of guiding
tube inside the
machine is no
less than 28 cm.
In the material page, press the circular
materials.
material button to switch between different
Put the guiding tube into the rubber
ring.
After selecting the right material, click
“Extrude”. The print head temperature will
be displayed on the status bar on top.
Load Filament
Rubber
Grommet
Rubber
Grommet

2\ Click the “Build” button at the main1\
via USB, ethernet or Wi-Fi.
3\ Use the adjustment wheel to setup
the print job.
5\ Slicing and data tramission progress
will be shown on the status bar.
6\
the amount of time and material needed for the
4\ Click “Print”.
Load and Print 3D Models
7

menu to enter the print setup interface, click
Build
When the data transmission completes,
Connect the printer to the computer
“+” button to load a file (image or STL/UP3 file).
print job will be shown. After this point, the user
can safely disconnect from the printer.
Network Setup
The H400+ can be connected to your network either via ethernet or Wi-Fi.
For ethernet connection, follow instructions 1, 2, 3.
For Wi-Fi connections, follow instructions 1, 2, 4, 5, 6.
Click the “Config” button. Click the button.
Plug the network cable into the back of
the machine. If the printer successfully
connects to the network, the ethernet
connection icon will appear on the top
right of the status bar as shown below.
To use a WiFi connection, toggle the
WiFi option to ON, and choose the Wi-Fi
network that your computer is connected to.
Input the Wi-Fi password, then press
Return.
If the printer is successfuly connected
to the Wi-Fi network, the Wi-Fi connection
icon will appear in the top right of the status
bar as shown below.
