Agilent Technologies 85301B User manual

Agilent 85301B/C
Antenna Measurement Systems
45 MHz to 110 GHz
Configuration Guide

2
Table of Contents
3 Introduction
4 How to use this guide
4 General range parameters
4 Transmit site configuration
6 Range transfer function
7 Required measurement sensitivity
8 Selecting the system
10 85301B Antenna Measurement System
10 System configurations
12 Selecting the LO source
13 Reference signal level
13 Calculating reference power
14 Interconnect cables
19 RF cable ordering information
21 85301C Antenna Measurement System
21 IF interconnect cable
21 RF cables
21 Radiated reference signals
21 Reference phase-lock signal power level
22 Coupled reference signals
22 GPIB cables
22 GPIB extenders
23 Optional Capabilities
23 Manual antenna measurements
24 Measurement automation software
24 Millimeter-wave configuration
26 Multiple test channel configuration
27 Antenna positioning systems
29 Configuration Diagrams
29 General antenna range information
30 Transmit site configuration
31 85301B block diagram configuration
32 85301C block diagram configuration
32 Measurement automation
33 Millimeter-wave subsystem
34 Multiple-channel IF switching configuration
34 Multiple-channel RF switching configuration
35 Positioner configurations

3
Introduction
This Antenna Measurement Systems Configuration
Guide will help you configure a custom Agilent
Technologies 85301 or 85301C antenna measure-
ment system that meets your measurement
requirements. This guide is primarily for those cus-
tomers who desire to design, integrate, and install
their own antenna measurement systems using
Agilent antenna test instrumentation. The guide
will lead you through all the steps. For the do-it-
yourself customer, this guide will assist you in
determining what instrumentation to order from
Agilent Technologies. Your Agilent Technologies
sales engineer will be glad to assist you in procur-
ing the instrumentation. If desired, technical assis-
tance is available from systems engineers who are
experienced in configuring antenna measurement
systems.
Some customers may prefer the design, integra-
tion, and installation of an antenna instrumenta-
tion subsystem be performed for them by a solu-
tion supplier who has extensive antenna configura-
tion experience. Nearfield Systems, Inc. (NSI), an
Agilent Technologies channel partner, can provide
this service. NSI will work with you to understand
your measurement needs, and then design an RF
subsystem that meets your requirements. In addi-
tion to system design and configuration, NSI pro-
vides system integration, on-site installation, and
performance verification to ensure that the system
delivered meets your requirements. NSI will pro-
vide a complete RF subsystem, reducing your risk,
and eliminating the need for your personnel to
design and configure a system.
Other customers may need an application solution:
a complete system solution that addresses all
aspects of a measurement application, such as a
complete near-field or far-field measurement sys-
tem. You may be designing, building, and testing
antennas instead of an antenna measurement sys-
tem. Agilent Technologies recommends Nearfield
Systems, Inc. for complete near-field and far-field
application solutions. NSI has the measurement
expertise to supply a complete system to meet
your application requirement. NSI can configure
and supply the RF subsystem, the positioning sub-
system, provide the measurement application soft-
ware, and provide system installation and training.
If you choose to use NSI’s services, you will not
need to use this configuration guide; NSI will care-
fully consider all the issues covered in this configu-
ration guide. Your Agilent sales engineer has a
technical qualification guide that can be used to
help define your measurement requirements, and
he or she will be happy to work with you to define
your requirements. Your sales engineer can also
assist you in contacting NSI, or you can contact
NSI directly (California, USA) at [phone],
FAX [phone], by e-mail: [email protected],
or visit their extensive website at www.nearfield.com.
Main parts of an antenna range
In general, an antenna range measurement system
can be divided into two separate parts: the trans-
mit site and the receive site (see Figure 1). The
transmit site consists of the microwave transmit
source, amplifiers, and the communications link to
the receive site. The receive site consists of the
receiver, LO source, RF downconverter, positioner,
system software, and a computer.
Figure 1. Far-field antenna range
TRANSMIT SITE
• Synthesized Sweeper
• Amplifers
RECEIVE SITE
• Receiver • Positioner
• LO Source • Computer
• RF Downconverter

4
Configuration steps
Configuring an Agilent 85301 /C antenna mea-
surement system involves the following steps. Each
step is described in detail in this guide.
1. Select the transmit source, amplifiers, cables
and method used to obtain the reference channel
signal, and determine the minimum transmit
power.
2. Determine the worst-case antenna range transfer
function based on range length, maximum test fre-
quency, and transmit antenna gain.
3. Calculate the estimated test channel power level
based on transmit power, range transfer function,
and expected test antenna gain.
4. Determine required measurement sensitivity
based on test channel power level, required mea-
surement dynamic range, and accuracy.
5. Select either an 85301 or 85301C antenna mea-
surement system depending on range type and
required microwave performance.
6. Configure the receive site.
7. Calculate the reference channel power level.
8. Review the complete configuration for accuracy
and completeness.
9. You may wish to review the completed configu-
ration with your Agilent Technologies sales repre-
sentative and/or systems engineer, or with
Nearfield Systems, Inc.
How to use this guide
You can use Figures 16 through 25 at the end of
this guide as worksheets for configuring your
antenna measurement system. The bubble numbers
in these figures (example: ) indicate that a
value should be entered. These numbers corre-
spond directly with the bubble numbers by the
instructions in this guide. We recommend that you
photocopy Figures 16 through 25 and fill them in
as you go through the instructions.
General range parameters
Record the range type and length in Figure 16.
If a compact antenna test range (CATR) is to be
used, record the manufacturer and model number.
Transmit site configuration
The following steps are required to configure the transmit
site:
• Select the transmit source.
• Determine RF cable losses and transmit power
based on range type.
• Decide how the reference channel signal will be
obtained.
Transmit source selection
Record the required minimum and maximum
test frequencies for the antenna range in Figure 17.
ased on these frequency requirements, select a
transmit source from Table 1 below, check the
model number in Figure 17, and record its maximum
output power level at the upper test frequency on
Figure 17. Agilent recommends using only sources
with front panel controls; this will allow diagnos-
tics to be performed on the system if necessary.
The 1 Hz frequency resolution (Option 008) is
recommended for both the RF and LO sources to
allow the frequency resolution to be 1 Hz instead
of 1 kHz. While most users desire a 1 Hz frequency
resolution, it has the additional benefit of ensuring
that the signal presented to the receiver is within
its passband. If the system is to be used for mea-
suring antennas in pulsed mode of operation, fast
pulse modulation (Option 006) should be ordered.
1
1
2

5
Table 1. Agilent 85301B/C compatible transmit sources
Model Output
Number Description Power (dBm)
83620B 10 MHz to 20 GHz synthesized +13 dBm
sweeper with front panel controls.
Recommended options: Option 004,
rear-panel RF output; Option 008,
1 Hz frequency resolution.
83622B 2 GHz to 20 GHz synthesized +13 dBm
sweeper with front panel controls.
Recommended options: Option 004,
rear-panel RF output; Option 008,
1 Hz frequency resolution.
83623B 10 MHz to 20 GHz synthesized +17 dBm
sweeper with high output power
and front panel controls.
Recommended options: Option 004,
rear-panel RF output; Option 008,
1 Hz frequency resolution.
83624B 2 GHz to 20 GHz synthesized +20 dBm
sweeper with high output power
and front panel controls.
Recommended options: Option 004,
rear-panel RF output; Option 008,
1 Hz frequency resolution.
83630B 10 MHz to 26.5 GHz synthesized <20 GHz, +13 dBm
sweeper with front panel controls. (20 to 26.5 GHz,+10 dBm)
Recommended options: Option 004,
rear-panel RF output; Option 008,
1 Hz frequency resolution.
83640B 10 MHz to 40 GHz synthesized <26.5 GHz, +10 dBm
sweeper with front panel controls. (26.5 to 40 GHz, +6 dBm)
Recommended options: Option 004,
rear-panel RF output; Option 008,
1 Hz frequency resolution.
83650B 10 MHz to 50 GHz synthesized <26.5 GHz, +10 dBm
sweeper with front panel controls. 26.5 to 40 GHz, +5 dBm
Recommended options: Option 004, (40 to 50 GHz, +2.5 dBm)
rear-panel RF output; Option 008,
1 Hz frequency resolution.
Frequency coverage above 50 GHz is available using the Agilent 83550
series millimeter-wave source modules. Source modules are available in R
(26.5 to 40 GHz), Q (33 to 50 GHz), U (40 to 60 GHz), V (50 to 75 GHz) and
W (75 to 110 GHz) bands. Refer to “Millimeter-wave configuration,” under
“Optional Capabilities.”
Transmit site RF cabling
The transmit site RF cabling will depend on the
transmit amplifier and the method used to obtain
the reference channel signal. The amplifier should
be positioned as closely as possible to the transmit
antenna to preserve maximum output power at the
transmit antenna.
If no transmit amplifier is to be used, record
the length in meters of cable A1. Skip to .
If a transmit amplifier is to be used, record the
frequency range, gain and maximum output power
of the transmit amplifier, as well as the length in
meters of cables A2 and A3. For example, the fre-
quency range of the Agilent 8349 microwave
amplifier is 2 to 20 GHz with 14 d of gain and
+20 d m output power.
Record the nominal gain of the transmit anten-
na. If more than one antenna is used to cover the
required frequency range, record the nominal gain
of each antenna.
Agilent Technologies can also provide GPIB
controllable switch matrices for remote switch-
ing of the transmit antennas.
Reference channel signals
Almost all outdoor ranges and some long indoor
ranges obtain the reference channel signal using a
stationary reference antenna to receive a portion
of the radiated transmit signal. Shorter indoor
ranges can often use a coupled reference signal to
route the reference channel signal to the receiver
using coaxial cable or waveguide.
If a radiated reference will be used, skip to .
3
5
4
5
7

6
If a coupled reference is chosen, one or more
directional couplers must be chosen to cover the
desired frequency range. Table 2 lists typical cou-
pler parameters. To maximize transmit and refer-
ence channel power, select a coupler with the low-
est coupling factor and insertion loss that matches
the frequency range of the transmit antenna.
roadband couplers (1 to 40 GHz) are also avail-
able with 16 d coupling factors if sufficient power
is available. Record the lengths of cables A4 and
A5 and the insertion loss and coupling factor of
the directional coupler in Figure 17.
Table 2. Directional coupler data
Frequency Insertion Coupling
Description Range (GHz) Loss (dB) Factor (dB)
778D 0.1 to 2 0.6 20
87300B 1 to 20 1.5 10
87300C 1 to 26.5 1.7 10
87301D 1 to 40 1.9 13
87301E 2 to 50 2.0 10
Narda 4226-10 0.5 to l8 1.5 10
Narda 4202B-10 1 to 12.4 1.3 10
Narda 4203-10 2 to 18 2.0 10
Cable A4 should be ept as short as possible to
preserve transmit power, and can be eliminated
if the coupler can be connected directly to the
transmit antenna.
Transmit power
From the parameters recorded in Figure 17,
determine the power level at the input to the trans-
mit antenna by subtracting the cable losses and
adding amplifier gain to the output power level of
the transmit source. Insertion loss curves for the
Agilent 85381 series cables are shown in Figures 12
and 13. e careful to select a cable that will cover
the desired frequency range. Use the maximum
test frequency to determine the worst-case trans-
mit power level.
Range transfer function
The range transfer function (Pr/Pt) of an antenna
range determines the difference in power levels
between the input to the transmit antenna and the
output of an isotropic (0 d i) antenna located at
the receive site. This range transfer function
(which is a loss) is due to the dispersive nature of
a transmitting antenna. A transmitting antenna
radiates a spherical wavefront; only a portion of
this spherical wavefront is captured by the receiv-
ing antenna.
For a free-space far-field range, this range transfer
function is easily determined as follows:
Pr/Pt= Gt- (32.45 + 20*log (R) + 20*log (F))
where Gt= Transmit antenna gain (dBi)
R = Range length (meters)
F = Test frequency (GHz)
This equation does not account for atmospheric
attenuation, which can be a significant factor
in certain millimeter-wave frequency ranges.
Compact Antenna Test Ranges (CATRs) achieve
greater transfer efficiency by collimating, or
focusing the transmitted power using one or more
shaped reflectors. Transfer functions for most
CATRs are available from the manufacturer's data
sheet or on request. If the transfer function is
unavailable, use the free-space transfer function
as a worst-case estimate.
Record the transfer function in Figure 16 for
the minimum and maximum test frequencies.
6
7
8

7
The test channel received power level, Pr (TEST),
must be calculated to determine the approximate
maximum power level present at the output of the
antenna-under-test (AUT). The required measure-
ment sensitivity is determined from the test chan-
nel received power level, the required dynamic
range, and the required measurement accuracy.
The maximum test channel received power level
will occur when the AUT is boresighted relative to
the transmit antenna.
Record the estimated minimum boresight AUT
gain, G (AUT), calculate the test channel received
power level as follows and record it in Figures 16,
18, and 19.
Pr(TEST) = Pt+ Pr/Pt+ G (AUT)
where Pr(TEST) = Test channel received power level (dBm)
Pt= Transmit power (dBm)
Pr/Pt= Range transfer function (dB, at the max-
imum test frequency)
G (AUT) = Expected minimum boresight gain of
AUT (dB)
Required measurement sensitivity
The required measurement sensitivity of the sys-
tem is a function of measurement transmit power,
range transfer function, AUT gain, required mea-
surement dynamic range, and desired measure-
ment accuracy. The previous steps have deter-
mined the approximate power level present at the
output of the AUT under boresight conditions.
The measurement dynamic range required to test
the AUT is the difference, in decibels, between
boresight and the lowest AUT level that must be
measured. Examples of these include side-lobe
level, null depth, and cross-polarization levels.
Record the required dynamic range in Figure 16.
Measurement accuracy is also affected by the mea-
surement sensitivity of the system. The signal-to-
noise ratio will directly impact the measurement
accuracy of the system for both amplitude and
phase measurements. Figure 2 illustrates the rela-
tionship between signal-to-noise ratio and magni-
tude and phase errors.
Figure 2. Measurement accuracy as a function of signal-
to-noise ratio
Record the required signal-to-noise ratio in d
in Figure 16.
The overall system measurement sensitivity
required is the test channel received power level
minus the sum of the required dynamic range and
signal-to-noise ratio.
Calculate the required measurement sensitivity
by subtracting the required dynamic range and sig-
nal-to-noise ratio from the test channel received
power level. Record the value in Figure 16.
The required measurement accuracy for low-
level AUT responses is not always as stringent
as the accuracy required for high-level AUT
responses.
9
10
11
12

8
Selecting the system
Figure 3 will help you select either an Agilent
85301 or 85301C antenna measurement system,
depending on your range type and the required
microwave performance. If you select an 85301
system, you will configure the receive site with an
85310A distributed frequency converter (mixer-
based). If you choose an 85301C system, you will
configure the receive site with either an 8511A
(45 MHz to 26.5 GHz) or 8511 (45 MHz to 50 GHz)
frequency converter (harmonic sampler-based).
System performance with these converters is
shown in Tables 3 and 4.
Indoor range
Require measurements
>50 GHz now or
in the future?
Need to measure signals
<-115 dBm (0.045 to 26.5 GHz) or
<-100 dBm (26.5 to 50 GHz)?
Require mixers at
antenna-under-test?
Select 85301C system*
(uses 8511A/B frequency converter)
Select 85301B system
(uses 85310A frequency converter)
No No No
Outdoor range
YesYesYes
*85301B can also be used;
will provide greater sensitivity
Figure 3. Selecting an antenna measurement system
Table 3. Performance of an 85301B system (with 85310A distributed frequency converter)
85320A/B 85320A/B 85320A/B
Option H20 mixers3standard mixers Option H50 mixers3
Specification 0.1 to 3 GHz 1 to 2 GHz12 to 18 GHz 6 to 26.5 GHz 2 to 18 GHz 6 to 26.5 GHz
Sensitivity2(dBm) -107 -80 -113 -96 -110 -95
Compression level4(dBm) -21 -24 -24 -15 -24 -27
Dynamic range5(dB) 86 56 89 81 86 68
Channel isolation6(dB) 100 100 100 100 100 100
Typical RF input match (dB) 8 8 8 8 5 5
Table 4. Performance of an 85301C system (with 8511A/B frequency converters)
Specification 0.045 to 8 GHz 8 to 20 GHz 20 to 26.5 GHz 26.5 to 40 GHz 40 to 50 GHz
Maximum output power7(dBm)
83630B8+10 +10 +3 — —
83650B8+10 +10 +4 +3 0
Sensitivity2(dBm) (S/N = 1,0 avgs), 8511A [B] -98 -98 -94 [-89] [-89] [-87]
Sensitivity2(dBm) (S/N = 1,128 avgs), 8511A [B] -119 -119 -115 [-110] [-110] [-108]
Dynamic range (dB, 0 averages) 8511A [B] 88 88 79 [74] [74] [68]
Compression level4(dBm) -10 -10 -15 -15 -19
Channel isolation6(dB, ref to test), 8511A [B] 80 [85] 80 [85] 80 [75] [75] [70]
Return loss (dB, RF input) 17 15 9 9 7
Min. phase-lock power9(dBm), 8511A [B] -40 [-41] -38[-39] -35 [-32] [-32] [-30]
1. Performance from 1 to 2 GHz is typical.
2. Sensitivity is defined as signal = noise, IF bandwidth = 10 kHz. Averaging will improve sensitivity by 10 log (number of averages).
3. Typical performance.
4. RF level for 0.1 dB compression.
5. Broadband dynamic range is the measured difference between the compression level and the average noise floor. Achievable dynamic range for CW measurements is 2 to 3 dB
better.
6. Channel isolation is the coherent RF leakage from the reference channel to the test channel.
7. Cable loss can be determined from Figures 12 and 13.
8. Frequency resolution for the 83630B and 83650B = 1 Hz. (with Option 008)
9. Minimum phase-lock power is the typical minimum RF power at the a1 or a2 input to achieve phase-lock.

9
The following factors should also be considered
when choosing your system:
• The 85310A distributed frequency converter
(85301 system) allows the test mixer to be
located at the AUT, avoiding the degradation in
measurement sensitivity due to cable insertion
loss between the 8511A/ RF inputs and the
AUT.
• Measurement sensitivity and acquisition time
are directly related. If averaging is used to
achieve the required measurement sensitivity,
data acquisition times will be increased.
Averaging will improve sensitivity by 10*log
(Averaging Factor) until limited by channel-to-
channel isolation. The increase in acquisition
time can be determined by multiplying the aver-
aging factor by 200 microseconds. If acquisition
time is critical, fundamental mixing using the
85310A will reduce or eliminate the need for
averaging.
• If the distance between the 8530A and the AUT
is large, both the LO source and the 85310A
frequency converter can be remoted from the
8530A. Remote distances of up to 25 meters
cause no degradation in system sensitivity;
beyond 25 meters, the system sensitivity
degrades by 0.1 d per meter.
The 85301C antenna measurement system utilizes
an 8511A/ frequency downconverter which uses
a harmonic sampling technique with a built-in
voltage-tuned oscillator. This type of downconver-
sion does not require a second synthesized source
as a local oscillator, so it will be a lower-cost RF
system.
The 85301C system has a low-frequency limit of
45 MHz; the 85301 has a low-frequency limit of
100 MHz.
The 85301 system utilizes mixers for frequency
downconversion. While these mixers are relatively
broadband, they are banded. Mixers are available
for the frequency bands of 100 MHz to 3 GHz, 1 to
26.5 GHz, 2 to 50 GHz, 40 to 60 GHz, 50 to 75 GHz,
and 75 to 110 GHz.
The 85301C system provides broadband frequency
downconversion: either 45 MHz to 26.5 GHz, or
45 MHz to 50 GHz coverage.

10
Agilent 85301B Antenna Measurement System
The Agilent 85301 antenna measurement system
uses the Agilent 85310A distributed frequency con-
verter to downconvert the microwave signal to an
IF frequency that can be measured by the receiver.
The 85310A distributed frequency converter is
based on an external mixer configuration and
consists of the 85309A LO/IF distribution unit,
85320A test mixer module, 85320 reference mixer
module and accessories. When combined with an
appropriate LO source, the 85310A provides fun-
damental downconversion from 2 to 18 GHz and
third harmonic downconversion from 6 to 26.5 GHz
(see Figure 4). The frequency coverage can be
extended to 110 GHz by the 85325 millimeter-wave
subsystems, which are discussed under “Millimeter-
wave configuration.” The 85310A is a single-chan-
nel downconverter (one test and one reference).
A second test channel can be added by ordering
85310A Option 00l. For two additional test channels
(a total of one reference channel and three test
channels), order Option 002.
The 85309A LO/IF distribution unit provides
LO signal amplification and isolation, IF pre-
amplification and filtering, and an LO/IF diplexer
for the test channel. The 85320A test mixer module
contains an LO/IF diplexer, double-balanced mixer
and a 3 d matching pad on the RF port. The 85320
reference mixer module contains a directional cou-
pler, leveling detector, double-balanced mixer and
a 3 d matching pad on the RF port. An adapter
cable for IF connections between the 85309A and the
8530A is included with the 85310A as well as 3 d
and 6 d fixed attenuators.
A leveling detector in the reference mixer is used
to provide the proper LO drive to the mixers. It is
important to use equal length cables to both the
reference and test mixers to ensure the same cable
loss, and provide the same LO drive power to both
mixers.
Figure 4. Interconnect diagram of an 85310A distributed
frequency converter
Weatherproof enclosures
If the 85309A LO/IF unit and/or the LO source are
to be located outdoors, the units must be protected
from inclement weather.
System configurations
Figures 5 through 8 illustrate several common
range configurations in which an 85310A frequency
converter would be used. Figure 5 represents the
most common outdoor configuration, where the
receiver and LO source are located in the control
room, the 85309A LO/IF unit is located close to the
antenna positioner and the mixer modules are con-
nected directly to the reference and test antennas.
If the distance between the LO source and the
85309A exceeds the maximum LO cable lengths,
a synthesized LO source can be remoted with the
85309A using 37204A GPI extenders (see “GPI
extenders”). Remoting the 85309A LO/IF distribu-
tion unit up to 25 meters from the 8530A causes
no degradation in system sensitivity; beyond
25 meters, the system sensitivity degrades by
0.1 d per meter.
RF In
3.5 mm male
DET Out
85302B
Reference
Mixer
Module
REF LO In
REF IF Out
EXT LVL In
REF IF In
REF LO Out
85309A
LO/IF Unit
LO In
IF Out
LO Out
IF In
REF IF Out
TEST IF Out
Positive Z
Blank
LO
Input
Z-axis RF
Out
8530A
REF IF In (A1)
TEST IF In (B2)
85320A
Test Mixer
Module
RF In
3.5 mm
male
LO Source

11
In Figure 6, the transmit source and 8530A are
located in the control room and a synthesized LO
source, 85310A frequency converter and GPI
extender are located on the rail cart with the posi-
tioning system and AUT. The GPI extender cable,
together with coaxial cables transmitting the refer-
ence and test IF signals, are fed from a spool
mounted on the rail cart.
Figure 5. Typical outdoor far-field antenna range
configuration
85309A
LO/IF Unit
85320B
Reference
Mixer
Module
8530A LO Source (83620B)
Control
Room
85320A
Test Mixer
Module
AUT
Reference
Antenna
Figure 6. Outdoor range configuration using rail cart
85320B
Reference
Mixer
Module
85320A
Test Mixer
Module
Rail Cart 85309A LO/IF Unit
37204A
LO Source
Reference
Antenna
37204A
8360
RF Source
8530A
Control Room
AUT
Transmit
Antenna

12
In Figure 7, the range uses a single-reflector CATR
to collimate the transmit beam to a plane wave.
In this case, the transmit source, LO source, the
85309A LO/IF unit and GPI extender are located
in the positioner/feed pit. The 8530A, positioner
controller and computer system are located in the
control room.
Figure 7. Indoor range using single-reflector CATR
A dual-reflector CATR range is configured slightly
differently (Figure 8). The transmit source is located
in the control room with the 8530A. If the reference
mixer module will not reach the transmit source
due to cable length restrictions, the coupled refer-
ence signal can be routed to the reference mixer
module using coaxial cable.
Figure 8. Indoor range using dual-reflector CATR
In all configurations, the cable lengths between the
85309A LO/IF distribution unit and the reference
and test mixers should be the same length. Mixer
power level is adjusted and leveled at the reference
mixer; using the same cable lengths for the test
mixer insures proper LO drive power to the test
mixer.
Selecting the LO Source
The 85301 antenna measurement system uses
synthesized RF and LO sources. Since the RF and
LO signals are synthesized, phase lock for the
receiver is unnecessary. Microwave mixers used
with the 85301 antenna measurement system use
fundamental mixing from 100 MHz to 18 GHz, and
harmonic mixing for frequencies above 18 GHz.
Thus, an LO source that operates over the frequency
range of 0.1 to 18 GHz will be adequate for all fre-
quencies of operation of the 85301 . A large selec-
tion of synthesized sources is available for LO
sources (refer to Table 1). However, because the
LO source only needs to operate over the frequency
range of 0.1 to 18 GHz, LO source selection can be
limited to the synthesizers shown in Table 5.
Table 5. Agilent 85301B LO sources
Model Output
Number Description Power (dBm)
83620B 10 MHz to 20 GHz synthesized sweeper with + 13 dBm
front panel controls.
Recommended Options: Option 004, rear-panel
RF output; Option 008, 1 Hz frequency resolution.
83622B 2 GHz to 20 GHz synthesized sweeper with +13 dBm
front panel controls.
Recommended Options: Option 004, rear-panel
RF output; Option 008, 1 Hz frequency resolution.
83623B 10 MHz to 20 GHz synthesized sweeper with +17 dBm
high output power, and front panel controls
Recommended Options: Option 004, rear-panel
RF output; Option 008, 1 Hz frequency resolution.
83624B 2 GHz to 20 GHz synthesized sweeper with +20 dBm
high output power, and front panel controls.
Recommended Options: Option 004, rear-panel
RF output; Option 008, 1 Hz frequency resolution.
85320B
Reference
Mixer RF Source
85320A
Test Mixer
Module
Positioner
Pit
Antenna
Under
Test
Transmit
Feed
LO Source
8530A
37404A
GPIB
Extender
Reflector
85309A
LO/IF Unit
37204A
GPIB
Extender
Subreflector
Control
Room
85320B
Reference
Mixer Module
RF Source
85320A
Test
Mixer
Module
Positioner
Pit
Antenna
Under Test
Transmit
Feed
LO Source
Reference and
Test IF Signals
85309A
LO/IF Unit
37204A
GPIB
Extender
GPIB Extender
Cable
To Control
Room
Reflector

13
Select a source that meets your individual prefer-
ences and needs. The higher-output power sources
are useful when the distance between the LO source
and the 85309A LO/IF, distribution unit is longer
than the standard allowable cable lengths shown
in Tables 6 through 11. y using the cable inser-
tion loss curves (Figures 12 and 13) the additional
cable length can be calculated for the higher-output
power sources. The 1 Hz frequency resolution
(Option 008) is recommended for both the RF and
LO sources to provide a system frequency resolu-
tion of 1 Hz instead of 1 kHz.
Reference signal level
The reference mixer provides a phase reference for
the measurement, and a reference signal for a
ratioed measurement (b2/a1) to ratio out any vari-
ations in signal levels from the system. Since both
the RF and LO sources are synthesized, phase
locking the receiver is not required. The only
requirement for the reference channel is that the
signal level be high enough to achieve the desired
accuracy for the measurement. Figure 2 shows the
magnitude and phase errors as a function of signal-
to-noise ratio; this also applies to errors contributed
by the reference channel. For most applications, it
is desirable to maintain a 50 to 60 d signal-to-
noise ratio. For fundamental mixing (2 to 18 GHz),
the sensitivity is -113 d m; maintaining a 50 to 70 d
signal-to-noise ratio would require a reference
channel signal level of -40 to -60 d m.
Record the model number of the selected LO
source in Figure 18.
Calculating reference power
Calculation of the reference channel power level
depends on the method used to obtain the refer-
ence signal. Use the sections below to determine
the reference channel power level for either a radi-
ated reference signal or a coupled reference signal.
Radiated reference signals
When using a radiated reference, the reference
channel power level can be determined from the
following equation:
Pr(REF) = Pt+ Pr/Pt+ G (REF)
where Pr(REF) = Power level at the output of the reference
antenna
Pt= Transmit power level (dBm)
Pr/Pt= Transfer function of the range
G (REF) = Gain of the reference antenna
Record the reference antenna gain in Figure 18.
Record the calculated reference channel power
level Pr (REF) in Figure 18.
If the calculated reference channel power level
is insufficient to achieve the desired accuracy
from the reference channel, the transmit power
or the reference antenna gain must be
increased.
Coupled reference signals
When using a coupled reference, the reference
channel power level can be determined by sub-
tracting the cable insertion losses and the coupling
factor of the directional coupler and adding ampli-
fier gain, if any, to the output power of the transmit
source. Insertion loss curves for 85381 series cables
are shown in Figures 12 and 13.
Record the calculated reference channel power
level Pr (REF) in Figure 18.
13
14
15
16

14
Interconnect cables
The Agilent 85310A frequency converter requires
coax cables for routing LO, IF and DC leveling sig-
nals between the 85309A LO/IF unit, 8530A, mixer
modules and the LO source. Agilent Technologies
has several different types of cables available to
meet these cabling needs. They are described
below.
Output power of LO/IF distribution unit
Mixers require a certain LO drive power level; the
output power of the 85309A LO/IF distribution
unit and the RF loss of the cables will determine
the maximum allowable cable lengths. The cable
length tables and power level diagrams shown in
this configuration guide are based on the standard
85309A specifications.
Higher-output power LO/IF distribution units
Agilent Technologies also offers the 85309A with
special options for higher output power. When
designing a system with a special high-power unit,
verify the output power specifications, and make
adjustments to cable lengths based on the power
level. Cable lengths shown in Figures 9–11 and 15,
and Tables 6–11 and 14–15 are calculated from the
following formulas:
Cable L1 length (meters) = (POUT source - PIN 85309A)
/(cable loss/meter @frequency)
Cable L2 length (meters) = (POUT 85309A - PIN mixer)
/(cable loss/meter @frequency)
The cable length tables that follow show cable
lengths in parentheses for the 85309A Special
Option H30, H31, and H32, which are the most
popular higher-power specials. These specials have
the following minimum specified leveled power: 0.3
to 0.5 GHz, 25 d m; 0.5 to 8.4 GHz, 27 d m; 8.4 to
18 GHz, 24.5 d m. Minimum specified leveled
power over 0.3 to 18 GHz is 24.5 d m.
Fundamental versus harmonic mixing
Loss of LO cables is dependent on RF frequencies;
lower frequencies have lower loss per unit length,
and higher frequencies have higher loss (refer to
Figures 12 and 13). Therefore the maximum LO
frequency utilized will affect the maximum length
of the cables. The maximum LO frequency is
dependent on the frequency specified for the
antenna range and whether fundamental or har-
monic mixing is used. Lower LO frequencies have
less loss and allow longer cable lengths; higher LO
frequencies have higher losses, so cable lengths are
shorter. There is a trade-off between LO frequency
and system sensitivity. Fundamental mixing pro-
vides the lowest conversion loss in the mixer, and
the best system sensitivity. Harmonic mixing
allows lower LO frequencies to be used (with
longer cable lengths), but has higher conversion
loss in the mixer, and less system sensitivity.
Standard versus low-loss cables
The RF loss of the cables will affect the maximum
length of cable that can be used between the 85309A
and the mixers. The standard 85381A/C/D cables
have losses as shown in Figures 12 and 13. Special
low-loss cables, such as the MA/COM FA29RX
cable, are about half the loss of the standard
cables. Therefore the low-loss cables will provide
approximately twice the distance between the
85309A and the mixers. The trade-off is higher
price and somewhat less durability. MA/COM can
be contacted at [phone], FAX [phone],
or visit their website at www.macom.com. Other
cable manufacturers, such as W.L. Gore &
Associates, may have similar low-loss cables that
would be satisfactory in this application. W.L. Gore
& Associates can be contacted at [phone],
or visit their website at www.gore.com.

15
The following figures and tables define the allow-
able cable lengths between the LO source and
85309A LO/IF distribution unit, and between the
85309A and the mixers. Tables 6, 8, and 10 show
maximum cable lengths with standard 85301A/C
cables. Tables 7, 9, and 11 show maximum cable
lengths with MA/COM FA29RX low-loss cables.
Maximum cable lengths with 1 to 26.5 GHz mixers
The standard mixers used in Agilent antenna
measurement systems are the 85320A test mixer
and the 85320 reference mixer. oth mixers oper-
ate from 1 to 18 GHz in fundamental mode, and
from 6 to 26.5 GHz in third-harmonic mode. While
the 85320A/ mixers are not specified from 1 to
2 GHz, they will operate in this frequency range
with degraded sensitivity. Figure 9 shows the RF
power
levels required for proper operation with the
85320A/ mixers. Table 6 shows the maximum
allowed 85381A/C cable lengths from the LO source
to the 85309A, and from the 85309A to the 85320A/
test and reference mixer modules. Table 7 shows
the maximum cable lengths with special low-loss
cables.
Figure 9. Required RF power levels for 85320A/B mixers
85320B
Reference
Mixer
85320A
Test Mixer
83620B
Synthesized Source 85309A LO/IF Distribution Unit
Cable Length L1 Cable Length L2
POut = 13 dBm P
In
=0-5 dBm POut = 19 dBm*
POut = 19 dBm*
PIn = 7.5 dBm
P
In
= 7.5 dBm
Cable Length L2
*Minimum specified leveled power; 2-9 GHz, POut = 20.4 dBm; 9-18 GHz, POut = 19 dBm.
Table 6. 85381A cable lengths with 85320A/B mixers
Maximum LO Frequency Maximum cable length (L1,meters) Maximum cable length (L2,meters)
bands (GHz) LO source to 85309A 85309A to 85320A/B Operating bands
18 5 (5)17 (12)11 to 18 GHz fundamental
6 to 26.5 GHz 3rd harmonic
12.4 7 (6.2)19 (15.3)11 to 12.4 GHz fundamental
6 to 26.5 GHz 3rd harmonic
9 10 (7.4)112 (18)11 to 9 GHz fundamental
6 to 26.5 GHz 3rd harmonic
6 13 (9.2)115 (22.5)11 to 6 GHz fundamental
6 to 26.5 GHz 3rd harmonic
3.6 27 (11.5)129 (28)11 to 3.6 GHz fundamental
3.6 to 18 GHz 5th harmonic
Table 7. Special low-loss cable lengths with 85320A/B mixers, and MA/COM FA29RX cable
Maximum LO Frequency Maximum cable length (L1,meters) Maximum cable length (L2,meters)
bands (GHz) LO source to 85309A 85309A to 85320A/B Operating bands
18 10 (10)115 (25.9)11 to 18 GHz fundamental
6 to 26.5 GHz 3rd harmonic
12.4 12 (13)119 (32)11 to 12.4 GHz fundamental
6 to 26.5 GHz 3rd harmonic
9 15 (15)124 (38)11 to 9 GHz fundamental
6 to 26.5 GHz 3rd harmonic
6 20 (19)131 (47)11 to 6 GHz fundamental
6 to 26.5 GHz 3rd harmonic
1. Maximum cable lengths with special high-powered 85309A-H30, H31, H32 units.

16
Maximum cable lengths with 2 to 50 GHz mixers
Agilent Technologies offers 85320A/ Option H50
mixers that operate from 2 to 50 GHz with a single
2.4-mm coaxial connector at the RF input port.
These mixers are popular when operation above
26.5 GHz is required. The 85320A-H50 test mixer
and the 85320 -H50 reference mixer operate from
2 to 18 GHz in fundamental mode, and from 6 to
50 GHz in third-harmonic mode.
Figure 10 shows the RF power levels required for
proper operation with the 85320A/ Option H50
mixers. Table 8 shows the allowed 85381A/C cable
lengths from the LO source to the 85309A, and
from the 85309A to the 85320A/ -H50 test and
reference mixer modules. Table 9 shows the cable
lengths with special low-loss cables.
Figure 10. Required RF power levels for Agilent
85320A/B-H50 mixers
85320B-H50
Reference
Mixer
85320A-H50
Test Mixer
83620B
Synthesized Source 85309A LO/IF Distribution Unit
Cable Length L1 Cable Length L2
POut = 13 dBm P
In
=0-5 dBm POut = 19 dBm
POut = 19 dBm
PIn = 12 dBm
P
In
= 12 dBm
Cable Length L2
Table 8. 85381A cable lengths with 85320A/B-H50 mixers
Maximum LO Frequency Maximum cable length (L1,meters) Maximum cable length (L2,meters)
bands (GHz) LO source to 85309A 85309A to 85320A/B Operating bands
18 5 (5)15 (8.9)12 to 18 GHz fundamental
18 to 50 GHz 3rd harmonic
16.7 9.5 (5)15 (9.3)12 to 16.7 GHz fundamental
16.7 to 50 GHz 3rd harmonic
13.3 7 (6)16 (10)12 to 13.3 GHz fundamental
13.3 to 40 GHz 3rd harmonic
Table 9. Special low-loss cable lengths with 85320A/B-H50 mixers, and MA/COM FA29RX cable
Maximum LO Frequency Maximum cable length (L1,meters) Maximum cable length (L2,meters)
bands (GHz) LO source to 85309A 85309A to 85320A/B Operating bands
18 10 (10.5)110 (19)12 to 18 GHz fundamental
18 to 50 GHz 3rd harmonic
16.7 11 (11.6)111 (21)12 to 16.7 GHz fundamental
6.7 to 50 GHz 3rd harmonic
13.3 13 (12.7)112.4 (22.8)12 to 13.3 GHz fundamental
13.3 to 40 GHz 3rd harmonic
1. Maximum cable lengths with special high-powered 85309A-H30, H31, H32 units.

17
Maximum cable lengths with low-frequency mixers
Agilent Technologies offers 85320A/ Option H20
mixers that operate from 0.1 to 3 GHz. These mix-
ers are popular when operation below 2 GHz is
required. The 85320A-H20 test mixer and the
85320 -H20 reference mixer operate from 0.1 to
3 GHz in fundamental mode.
A standard 85309A LO/IF distribution unit
operates over the frequency range of 1 to
26.5 GHz with standard 85320A/B mixers. It
also operates over the frequency range of 0.3
to 3 GHz with 85320A/B Option H20 mixers,
and over the range of 2 to 50 GHz with
85320A/B Option H50 mixers. Measurement
capability over the frequency range of 0.1 to
0.3 GHz requires an 85309A configured with
Special Option H20.
Figure 11 shows the RF power levels required for
proper operation with the 85320A/ -H20 mixers.
Table 10 shows the allowed 85381A/C Cable
lengths from the LO source to the 85309A, and
from the 85309A to the 85320A/ -H20 test and
reference mixer modules. Table 11 shows the cable
lengths with special low-loss cables.
Figure 11. Required RF power levels for 85320A/B-H20
mixers
85320B-H20
Reference
Mixer
85320A-H20
Test Mixer
83620B
Synthesized Source 85309A LO/IF Distribution Unit
Cable Length L1 Cable Length L2
POut = 13 dBm
PIn= 6-10 dBm
POut = 16 dBm
POut = 16 dBm
PIn = 8 dBm
PIn = 8 dBm
Cable Length L2
Table 10. 85381A cable lengths with 85320A/B-H20 mixers
Maximum LO Frequency Maximum cable length (L1,meters) Maximum cable length (L2,meters) System
bands (GHz) LO source to 85309A 85309A to 85320A/B Operating bands Sensitivity (dBm)
3 11 (13.8)113.8 (37.8)10.1 to 3 GHz fundamental -107
Table 11. Special low-loss cable lengths with 85320A/B-H20 mixers, and MA/COM FA29RX cable
Maximum LO Frequency Maximum cable length (L1,meters) Maximum cable length (L2,meters) System
bands (GHz) LO source to 85309A 85309A to 85320A/B Operating bands Sensitivity (dBm)
3 20 (22)129.5 (61)10.1 to 3 GHz fundamental -107
1. Maximum cable lengths with special high-powered 85309A-H20, H31, H32 units

18
Agilent 85381 series coaxial cables
The 85381A microwave cable is a semi-flexible
cable that operates from DC to 18 GHz. It is
intended for use as an LO cable between the LO
source and the 85309A LO/IF unit (see Figure 11).
If a rotary joint is used to route the test LO and IF
signals so that the cable is not continuously flexed,
the 85381A cable can be used between the 85309A
and the 85320A/ test and reference mixers. The
maximum orderable length for this cable is 25
meters. (See Figure 18, cables 3, 4 and 5.)
Refer to Figure 12 for cable loss characteristics.
The 85381C microwave cable is a flexible cable
that operates from DC to 26.5 GHz. It is intended
for use as a transmit site RF cable, and to connect
the output of the AUT to the mixer modules when
direct connection is not possible. The 85381C can
also be used as a flexible LO cable in non-rotary
joint applications where the 85381A proves unsuit-
able (see cable 2 in Figure 18). Maximum order-
able cable length is 30 meters.
The 85381D cable is a flexible microwave cable
that operates from DC to 50 GHz. It is intended for
use in 50 GHz systems. It is used to connect the
transmit source to the source antenna, and on the
AUT side of the antenna range to connect the AUT
to the 50 GHz test mixer. Maximum orderable cable
length is 10 meters. This cable has significantly
higher loss than the 85381A/C cables, and should
only be used when 50 GHz capability is required.
Refer to Figure 13 for cable loss characteristics.
The 85382A cable is a low-frequency (<100 MHz)
flexible cable. It is used to carry the 20 MHz signal
from the 85309A frequency converter to the 8530A
microwave receiver. This cable is also used to tie
the 10 MHz time bases of the RF and LO sources
together in applications where this is practical.
This cable can be ordered in lengths up to 200
meters.
Figure 12. Insertion loss for 85381 series cables
Figure 13. 85381A/C/D cables; typical insertion loss
0 5 10 15 20 25 30 35 40 45 50
6.0
5.5
5.0
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
.5
0
1.79
1.64
1.53
1.38
1.23
1.07
0.91
0.76
0.61
0.46
0.30
0.15
0
85381C
26.5 GHz
85381D
50 GHz
85381A
18 GHz
Frequency (GHz)
Insertion Loss (dB/meter)
Insertion Loss (dB/foot)
2.0
1.5
1.0
0.5
00 5 10 15 20 25
0
0.15
0.30
0.46
0.61
85381C
85381A
MA/COM FA29RX
Frequency (GHz)
Insertion Loss (dB/meter)
Insertion Loss (dB/foot)

19
RF cable ordering information
Cable length
Determine the type and length (in meters) of cable
required. Order the cable by type (85381A, C, D or
85382A) and length option Cxx, where ‘xx’ speci-
fies the length of the cable in meters. To order a
one-half meter cable, specify Option C00. To con-
vert feet to meters, multiply the number of feet by
0.3048.
Ordering example: To order a 23-foot cable for use
up to 26.5 GHz, order 85381C Option C07 (23 feet
x 0.305 = 7 meters).
Cable connectors
A variety of connector types are available for the
85381A/C/D and 85382A RF cables, as shown in
Table 12. Two connector options must be ordered
for each cable.
Table 12. RF cable connector options
Cable Type
Connector 85381A185381C185381D185382A1
Type DC to 18 GHz DC to 26.5 GHz DC to 50 GHz DC to 100 MHz
Type-N male CNM CNM2CNM
Type-N female CNF2
3.5 mm male C3M
3.5 mm female C3F
SMA male CSM CSM2
SMA female CSF2
BNC male CBM
BNC female CBF
2.4 mm male C2M
2.4 mm female C2F
1. Minimum bend radii for cables are as follows: 85381A/C/D, 5 cm (2 inches);
85382A, 6 cm (2.5 inches).
2. Maximum frequency is 18 GHz.
Cable ordering example:
To obtain a 23-foot cable for use up to 18 GHz with
a Type-N male connector on one end and an SMA
male connector on the other end, order an 85381A
Option C07, CNM, CSM. To get a 9-meter cable for
use up to 26.5 GHz with 3.5-mm male connectors
on each end, order an 85381C Option C09, C3M,
C3M.
Reference and test LO cables
The same LO cable type and length is required for
both the reference and test mixer modules. This is
to ensure that the insertion losses through the ref-
erence and test mixer module LO paths are the
same. Using the same LO cable type also optimizes
cable phase tracking versus temperature and,
therefore, system phase measurement, stability,
and accuracy.
Remote LO source
If the maximum cable distance between the LO
source and the 85309A LO/IF unit is insufficient, a
synthesized LO source may be remoted with the
85309A using 37204A GPI extenders. Remote dis-
tances of up to 25 meters cause no degradation in
system sensitivity; beyond 25 meters, the system
sensitivity degrades by 0.1 d per meter. System
sensitivity degradation is due to IF cable loss in
the 20 MHz IF cables connecting the 85309A to the
8530A.

20
Rotary joints
When a rotary joint is used, the equivalent cable
length must be added to the reference mixer LO
cable due to the rotary joint insertion loss. To
determine the equivalent cable length, first deter-
mine the insertion loss from the input to the output
of the rotary joint at the maximum LO frequency.
Record this value in Figure 18. Then use
Figure 12 or 13 to calculate the equivalent length
in meters at the maximum LO frequency using the
same cable type used for the LO cables between
the 85309A and the mixer modules. The reference
LO cable length must be increased by this amount.
Record the lengths and type of the LO cables
( 1 through 5) in Figure 18.
Record the lengths and type of the IF and lev-
eling cables (C1 through C5) in Figure 18.
Normally, 85382A cable is used.
In Figure 16, record the connector types of the
system components.
The semi-flexible 85381A cable is normally used
for cables 1, 3, 4, and 5. The flexible 85381C
cable is normally used for cables 2 and 5. The
85382A cable is normally used for cables C1, C2,
C3, C4, and C5.
17
18
19
20