Agilent Technologies Medalist x6000 User manual

Agilent Technologies
Agilent TechnologiesAgilent Technologies
Agilent Technologies
Medalist x6000
Medalist x6000Medalist x6000
Medalist x6000
System Installation and
System Installation and System Installation and
System Installation and
Verification
VerificationVerification
Verification

Medalist x6000
Medalist x6000 Medalist x6000
Medalist x6000 Installation and System Verification
Installation and System VerificationInstallation and System Verification
Installation and System Verification
Legal Notices, Warranty and Safety
Legal Notices, Warranty and SafetyLegal Notices, Warranty and Safety
Legal Notices, Warranty and Safety
1 Legal Notices .......................................................................................................................................... i
Copyrights ................................................................................................................................................... i
Trademarks.................................................................................................................................................. i
Technology Licenses Notice ........................................................................................................................ i
U.S. Government Restricted Rights ............................................................................................................. i
Agilent Address........................................................................................................................................... ii
2 Warranty.............................................................................................................................................. iii
3 Safety Summary................................................................................................................................... iv
General.......................................................................................................................................................iv
Before Applying Power...............................................................................................................................iv
Ground the Equipment ................................................................................................................................v
Fuses............................................................................................................................................................v
Do Not Operate in an Explosive Atmosphere..............................................................................................v
Do Not Remove Equipment Cover...............................................................................................................v
Do Not Operate Damaged Equipment........................................................................................................vi
Do Not Service or Adjust Alone..................................................................................................................vi
Do Not Substitute Parts or Modify Equipment ...........................................................................................vi
Maintain the System as Recommended.......................................................................................................vi
Follow All X-ray Safety Requirements and Legislation..............................................................................vi
4 Safety Symbols and Notices .............................................................................................................. viii
Warning ................................................................................................................................................... viii
Caution .................................................................................................................................................... viii
Note ......................................................................................................................................................... viii
Safety and Electric Symbols .................................................................................................................... viii
5 Emergency Stop .....................................................................................................................................x
6 De-energizing the X-ray Tube ........................................................................................................... xii
Methods for de-energizing the X-ray tube:............................................................................................... xii
X-Ray Control Off Button and X-Ray Control Key on the Operator Control Panel............................. xii
PDU Enable Switch and Lockable Breaker ......................................................................................... xiii
AC “Mains” Power Disconnect ........................................................................................................... xiv
7 X-Ray Safety ........................................................................................................................................xv
Effects of Radiation ..................................................................................................................................xvi

X-ray Dose Limits.....................................................................................................................................xvi
Definition of a Cabinet X-ray System .......................................................................................................xvi
Built-In Safety Features...........................................................................................................................xvii
Registration Requirements ......................................................................................................................xvii
8 High Voltage Safety......................................................................................................................... xviii
High Voltage Subsystem .........................................................................................................................xviii
Power Distribution Unit (PDU) ........................................................................................................... xix
9 Mechanical Safety................................................................................................................................xx
10 Service and Support .......................................................................................................................... xxi
Agilent Technologies Service Center........................................................................................................xxi
System Installation and Verification
System Installation and VerificationSystem Installation and Verification
System Installation and Verification
1 Overview ............................................................................................................................................... 1
2 Preparing for Agilent Medalist x6000 Installation ............................................................................ 2
3 Time Required for Installation ............................................................................................................ 3
4 What has to be done before installation begins?................................................................................ 4
5 System Arrival, Inspection and Placement......................................................................................... 5
6 System Hardware Installation and Setup......................................................................................... 13
7 System Performance Verification Procedure ................................................................................... 23
8 System Start-up................................................................................................................................... 27
9 Panel Handling Subsystem Verification ........................................................................................... 31
10 MSD Suggestion for Improvement Form ......................................................................................... 37
11 SMEMA – Appendix A ...................................................................................................................... 38
Introduction .............................................................................................................................................. 38
SMEMA Signals........................................................................................................................................ 38
SMEMA Connectors ................................................................................................................................. 40
12 Wiring Configuration – Appendix B................................................................................................. 42
Wiring Configuration ............................................................................................................................... 42
3-Phase Wye or Delta............................................................................................................................... 44
3-Phase Wye with Neutral ........................................................................................................................ 45

Legal Notices, Warranty and Safety
Legal Notices, Warranty and SafetyLegal Notices, Warranty and Safety
Legal Notices, Warranty and Safety
1Legal Notices .......................................................................................................................................... i
Copyrights ................................................................................................................................................... i
Trademarks.................................................................................................................................................. i
Technology Licenses Notice ........................................................................................................................ i
U.S. Government Restricted Rights ............................................................................................................. i
Agilent Address........................................................................................................................................... ii
2Warranty.............................................................................................................................................. iii
3Safety Summary................................................................................................................................... iv
General.......................................................................................................................................................iv
Before Applying Power...............................................................................................................................iv
Ground the Equipment ................................................................................................................................v
Fuses............................................................................................................................................................v
Do Not Operate in an Explosive Atmosphere..............................................................................................v
Do Not Remove Equipment Cover...............................................................................................................v
Do Not Operate Damaged Equipment........................................................................................................vi
Do Not Service or Adjust Alone..................................................................................................................vi
Do Not Substitute Parts or Modify Equipment ...........................................................................................vi
Maintain the System as Recommended.......................................................................................................vi
Follow All X-ray Safety Requirements and Legislation..............................................................................vi
4Safety Symbols and Notices .............................................................................................................. viii
Warning ................................................................................................................................................... viii
Caution .................................................................................................................................................... viii
Note ......................................................................................................................................................... viii
Safety and Electric Symbols .................................................................................................................... viii
5Emergency Stop .....................................................................................................................................x
6De-energizing the X-ray Tube ........................................................................................................... xii
Methods for de-energizing the X-ray tube:................................................................................................xii
X-Ray Control Off Button and X-Ray Control Key on the Operator Control Panel............................. xii
PDU Enable Switch and Lockable Breaker ......................................................................................... xiii
AC “Mains” Power Disconnect ........................................................................................................... xiv
7X-Ray Safety ........................................................................................................................................xv
Effects of Radiation ..................................................................................................................................xvi
X-ray Dose Limits.....................................................................................................................................xvi

Definition of a Cabinet X-ray System .......................................................................................................xvi
Built-In Safety Features...........................................................................................................................xvii
Registration Requirements ......................................................................................................................xvii
8High Voltage Safety......................................................................................................................... xviii
High Voltage Subsystem .........................................................................................................................xviii
Power Distribution Unit (PDU) ........................................................................................................... xix
9Mechanical Safety................................................................................................................................xx
10 Service and Support .................................................................................................................... xxi
Agilent Technologies Service Center .................................................................................................. xxi

Rev. A
Rev. ARev. A
Rev. A Legal Notices, Warranty and Safety
Legal Notices, Warranty and SafetyLegal Notices, Warranty and Safety
Legal Notices, Warranty and Safety
i
ii
i
1
1 1
1 Legal Notices
Legal NoticesLegal Notices
Legal Notices
Copyrights
CopyrightsCopyrights
Copyrights
© Agilent Technologies, Inc. 2007
Trademarks
TrademarksTrademarks
Trademarks
Agilent® is a registered trademark of Agilent
Technologies, Inc.
Intel® is a U.S. registered trademark of Intel
Corporation.
Java™ is a U.S. trademark of Sun Microsystems, Inc.
Adobe®, the Adobe Logo, Acrobat® and the Acrobat
Logo are trademarks of Adobe Systems Incorporated.
Microsoft®, Windows XP®, and MS-DOS® are U.S.
registered trademarks of Microsoft Corp.
Technology Licenses Notice
Technology Licenses NoticeTechnology Licenses Notice
Technology Licenses Notice
The hardware and/or software described in this document
are furnished under a license and may be used or copied
only in accordance with the terms of such license.
.S. Government Restricted Righ
.S. Government Restricted Righ.S. Government Restricted Righ
.S. Government Restricted Rights
tsts
ts
If software is for use in the performance of a U.S.
Government prime contract or subcontract, Software is
delivered and licensed as "Commercial computer software"
as defined in DFAR 252.227-7014 (June 1995), or as a
"commercial item" as defined in FAR 2.101(a) or as
"Restricted computer software" as defined in FAR 52.227-19
(June 1987) or any equivalent agency regulation or contract
clause.
Use, duplication or disclosure of Software is subject to
Agilent Technologies’ standard commercial license terms,
and non-DOD Departments and Agencies of the U.S.
Government will receive no greater than Restricted Rights
as defined in FAR 52.227-19(c)(1-2) (June 1987). U.S.
Government users will receive no greater than Limited
Rights as defined in FAR 52.227-14 (June 1987) or DFAR
252.227-7015 (b)(2) (November 1995), as applicable in any
technical data.

Rev. A
Rev. ARev. A
Rev. A Legal Notices, Warranty and Safety
Legal Notices, Warranty and SafetyLegal Notices, Warranty and Safety
Legal Notices, Warranty and Safety
ii
iiii
ii
Agilent Address
Agilent AddressAgilent Address
Agilent Address
Agilent Technologies
Measurement Systems Division
900 S. Taft Avenue
Loveland, CO 80537-6378

Rev. A
Rev. ARev. A
Rev. A Legal Notices, Warranty and Safety
Legal Notices, Warranty and SafetyLegal Notices, Warranty and Safety
Legal Notices, Warranty and Safety
iii
iiiiii
iii
2
2 2
2 Warranty
WarrantyWarranty
Warranty
The material contained in this document is provided "as is,"
and is subject to being changed, without notice, in future
editions. Further, to the maximum extent permitted by
applicable law, Agilent disclaims all warranties, either
express or implied with regard to this manual and any
information contained herein, including but not limited to
the implied warranties of merchantability and fitness for a
particular purpose. Agilent shall not be liable for errors or
for incidental or consequential damages in connection with
the furnishing, use, or performance of this document or any
information contained herein. Should Agilent and the user
have a separate written agreement with warranty terms
covering the material in this document that conflict with
these terms, the warranty terms in the separate agreement
will control.

Rev. A
Rev. ARev. A
Rev. A Legal Notices, Warranty and Safety
Legal Notices, Warranty and SafetyLegal Notices, Warranty and Safety
Legal Notices, Warranty and Safety
iv
iviv
iv
3
3 3
3 Safety Summa
Safety SummaSafety Summa
Safety Summary
ryry
ry
There are many warnings and cautions outlined in the next sections.
There are many warnings and cautions outlined in the next sections. There are many warnings and cautions outlined in the next sections.
There are many warnings and cautions outlined in the next sections. Properly follow ALL
Properly follow ALL Properly follow ALL
Properly follow ALL
Warnings and Cautions.
Warnings and Cautions.Warnings and Cautions.
Warnings and Cautions.
General
GeneralGeneral
General
The following general safety precautions must be observed
during all phases of operation, service and repair of this
product. Failure to comply with these precautions or with
specific warnings elsewhere in this manual violates safety
standards of design, manufacture, and intended use of the
product. Agilent Technologies, Inc. assumes no liability for
the customer's failure to comply with these requirements
Prior to operating or performing maintenance activities on
the Medalist x6000, personnel should be aware of system
safety precautions. The Medalist x6000 is designed to be
safe, provided proper use and service precautions are
observed. All users should be aware of the following areas of
safety:
Emergency Stop — How to shut off the Medalist x6000
Main Cabinet in an emergency situation.
De-energizing the X-ray Tube
X-Ray Safety — Effects of Radiation and the safeguards
against exposure.
High Voltage Safety – High Voltage and safe servicing
practices.
Mechanical Safety — Mechanical motion and safety
precautions.
B
BB
Before Applying Powe
efore Applying Poweefore Applying Powe
efore Applying Power
rr
r
Verify that the product is set to match the available line
voltage, the correct fuses or main circuit breaker is
installed, and all safety precautions are taken. Note the
instrument's external markings described under Safety
Symbols and Notices.
WARNING

Rev. A
Rev. ARev. A
Rev. A Legal Notices, Warranty and Safety
Legal Notices, Warranty and SafetyLegal Notices, Warranty and Safety
Legal Notices, Warranty and Safety
v
vv
v
Ground the Equipment
Ground the EquipmentGround the Equipment
Ground the Equipment
To minimize shock hazard, the instrument chassis and
cover must be connected to an electrical protective earth
ground. The instrument must be connected to the ac power
mains through a grounded power cable, with the ground
wire firmly connected to an electrical ground (safety
ground) at the power outlet. Any interruption of the
protective (grounding) conductor or disconnection of the
protective earth terminal will cause a potential shock
hazard that could result in personal injury.
This is a Safety Class 1 instrument (provided with a
protective earth terminal). An uninterruptible safety earth
ground must be provided from the main power source to the
product input wiring terminal or supplied power cable. The
protective features of this product may be impaired if it is
used in a manner not specified in the operation instructions.
Fuses
Fuses Fuses
Fuses
For continued protection against fire, only the fuses with
the required rated current, voltage, and specified type
(normal blow, time delay, etc.) should be used. Go to the
Service section of the on-line help for the specifications for
each fuse. Do not use repaired fuses or short-circuited fuse
holders. To do so could cause a shock or fire hazard.
Do Not Operate in an Explosive Atmos
Do Not Operate in an Explosive AtmosDo Not Operate in an Explosive Atmos
Do Not Operate in an Explosive Atmosphere
pherephere
phere
Do not operate the instrument in an explosive atmosphere
or the presence of flammable gases or fumes.
Do Not Remove
Do Not Remove Do Not Remove
Do Not Remove Equipment
EquipmentEquipment
Equipment Cov
CovCov
Cover
er er
er
Operating personnel must not remove instrument covers or
shields. Component replacement and internal adjustments
must be made only by service-trained personnel.
Under certain conditions, dangerous voltages may exist
even with the equipment switched off. To avoid dangerous
electrical shock, DO NOT perform procedures involving
cover or shield removal unless you are qualified to do so.
Do Not Operate Damaged Equipment
Do Not Operate Damaged EquipmentDo Not Operate Damaged Equipment
Do Not Operate Damaged Equipment
Whenever it is possible that the safety protection features
built into this product have been impaired, either through
physical damage, excessive moisture, or any other reason,
REMOVE POWER and do not use the product until safe
operation can be verified by service-trained personnel. If
necessary, contact your Agilent Technologies Service Center
for service and repair to ensure that safety features are
maintained.

Rev. A
Rev. ARev. A
Rev. A Legal Notices, Warranty and Safety
Legal Notices, Warranty and SafetyLegal Notices, Warranty and Safety
Legal Notices, Warranty and Safety
vi
vivi
vi
Equipment that appears damaged or defective should be
made inoperative and secured against unintended operation
until they can be repaired by qualified service personnel.
See the Lock Out /Tag Out procedure in the Service section
of the on-line help.
Do Not Service or Adjust Alo
Do Not Service or Adjust AloDo Not Service or Adjust Alo
Do Not Service or Adjust Alone
nene
ne
Do not attempt internal service or adjustment of this
instrument unless another person, capable of rendering
first aid and resuscitation, is present.
D
DD
Do Not Subs
o Not Subso Not Subs
o Not Subst
tt
titute Parts or Modify Equipme
itute Parts or Modify Equipmeitute Parts or Modify Equipme
itute Parts or Modify Equipment
ntnt
nt
Because of the danger of introducing additional hazards, do
not install substitute parts or perform any unauthorized
modification to the product. Contact your Agilent
Authorized Service Representative for service and repair to
ensure that safety features are maintained.
Maintain the System as Recommended
Maintain the System as RecommendedMaintain the System as Recommended
Maintain the System as Recommended
The recommended preventive maintenance for the system is
documented in the on-line help. Preventive maintenance
should always include testing the emergency shut down
(EMO) switch by pressing it and verifying that all ac and dc
power turns off.
Fol
FolFol
Foll
ll
low All X
ow All Xow All X
ow All X-
--
-ray Safety Requirements and Legislation
ray Safety Requirements and Legislationray Safety Requirements and Legislation
ray Safety Requirements and Legislation
DO NOT operate the equipment unless an X-ray safety
survey has been performed within the last six (6) months,
when the Medalist x6000 is installed at a site, when the
Medalist x6000 has been moved, and immediately following
maintenance that involves the safety interlock subsystem,
the lead shielding or the X-ray source.
Do not operate this equipment without complying to these
recommendations.
Owners/Operators of this equipment are responsible for
compliance with all local legislation regarding X-ray
equipment.
An Operator’s Guide and Declaration of Conformity in a
local language is available upon request to Agilent
Technologies, Inc.

Rev. A
Rev. ARev. A
Rev. A Legal Notices, Warranty and Safety
Legal Notices, Warranty and SafetyLegal Notices, Warranty and Safety
Legal Notices, Warranty and Safety
vii
viivii
vii
4
4 4
4 Safety Symbols and Notices
Safety Symbols and NoticesSafety Symbols and Notices
Safety Symbols and Notices
Warning
WarningWarning
Warning
The
The The
The WARNING symbol denotes a hazard. It calls attention to a procedure, practice, or condition,
WARNING symbol denotes a hazard. It calls attention to a procedure, practice, or condition, WARNING symbol denotes a hazard. It calls attention to a procedure, practice, or condition,
WARNING symbol denotes a hazard. It calls attention to a procedure, practice, or condition,
which, if not correctly
which, if not correctlywhich, if not correctly
which, if not correctly performed or adhered to, could result in personal injury or death. Do not
performed or adhered to, could result in personal injury or death. Do not performed or adhered to, could result in personal injury or death. Do not
performed or adhered to, could result in personal injury or death. Do not
proceed beyond a WARNING symbol until the indicated conditions are fully understood and met.
proceed beyond a WARNING symbol until the indicated conditions are fully understood and met.proceed beyond a WARNING symbol until the indicated conditions are fully understood and met.
proceed beyond a WARNING symbol until the indicated conditions are fully understood and met.
Caution
CautionCaution
Caution
The CA TION symbol denotes a hazard. It calls attention to an operating procedure, or condition,
which, if not correctly performed or adhered to, could result in damage to or destruction of part or all
of the product or permanent loss of data. Do not proceed beyond a CA TION symbol until the
indicated conditions are fully understood and met.
Note
NoteNote
Note
The NOTE symbol contains important information.
Safety and Electric Symbols
Safety and Electric Symbols Safety and Electric Symbols
Safety and Electric Symbols
These symbols are used on labels on the product and in the
documentation. They indicate that the user must refer to
the manual for specific information to avoid personal injury
or damage to the product.
Symbol Description
Warning, hazardous voltage (electrical hazard).
Warning, this equipment produces X-rays when energized.
Caution, refer to accompanying documents for specific WARNING or CA TION information to
avoid bodily injury or damage to the equipment.
(Canada) Warning, this equipment produces X-rays when energized.
Warning, pinch hazard. Keep hands away to avoid injury.
CAUTION
WARNING
NOTE

Rev. A
Rev. ARev. A
Rev. A Legal Notices, Warranty and Safety
Legal Notices, Warranty and SafetyLegal Notices, Warranty and Safety
Legal Notices, Warranty and Safety
viii
viiiviii
viii
Warning, pinch hazard. Keep hands away to avoid injury.
Warning, clamp pinch hazard. Keep hands away to avoid injury.
Indicates the field wiring terminal that must be connected to earth ground before operating the
equipment -- protects against electrical shock in case of fault.
Direct current (dc).
Frame or chassis ground terminal — typically connects to the equipment’s metal frame.
Alternating current (ac)

Rev. A
Rev. ARev. A
Rev. A Legal Notices, Warranty and Safety
Legal Notices, Warranty and SafetyLegal Notices, Warranty and Safety
Legal Notices, Warranty and Safety
ix
ixix
ix
5
5 5
5 Emerge
EmergeEmerge
Emergen
nn
ncy Stop
cy Stop cy Stop
cy Stop
The emergency stop buttons are intended for use in emergency situations only and should not be
used for normal system shut down. Repeated misuse of the emergency stop buttons will eventually
cause damage to certain components or the loss of data or both.
Figure 1 Emergency Stop
The emergency stop is used to quickly shut down power to
the Medalist x6000. The emergency stop is intended for
crisis situations only and should not be used as the normal
means to stop the Medalist x6000.
Push down on one of the emergency stop
buttons in an emergency situation.
The emergency stop button locks OFF
when pushed.
CAUTION

Rev. A
Rev. ARev. A
Rev. A Legal Notices, Warranty and Safety
Legal Notices, Warranty and SafetyLegal Notices, Warranty and Safety
Legal Notices, Warranty and Safety
x
xx
x
The Medalist x6000 is equipped with two emergency stop
buttons. The emergency stop buttons are located on either
side of the Medalist x6000, centered above the outer barrier
panels. Whenever one of the emergency stop buttons is
pressed, all power is immediately removed from the
Medalist x6000 subsystems, with the exception of the
system controller and the monitor.
To restart the Medalist x6000 after the emergency stop
button has been pushed (provided the condition which
caused the operator to engage the emergency stop button
has been cleared) requires the emergency stop release key
and the normal Medalist x6000 startup procedure.

Rev. A
Rev. ARev. A
Rev. A Legal Notices, Warranty and Safety
Legal Notices, Warranty and SafetyLegal Notices, Warranty and Safety
Legal Notices, Warranty and Safety
xi
xixi
xi
6
6 6
6 De
DeDe
De-
--
-energizing the X
energizing the Xenergizing the X
energizing the X-
--
-ray Tube
ray Tuberay Tube
ray Tube
In case of a disaster such as fire, explosion, flood, or strong
earthquake, the X-ray tube must be de-energized
immediately. In an emergency, de-energize the X-ray tube
by one of the following methods:
An electrical brownout or electrical power off, due to storms, does not constitute an emergency since
the system will simply shut itself off and may be restarted in the normal manner after the power
returns.
Methods for de
Methods for deMethods for de
Methods for de-
--
-energizing the X
energizing the Xenergizing the X
energizing the X-
--
-ray tube:
ray tube:ray tube:
ray tube:
Any one of the following actions will de-energize the X-ray
tube:
Press one of the emergency stop buttons.
Press the X-ray Control off (0) button on the operator
control panel
Turn the X-ray Control key to the off (0) position on the
operator control panel.
Turn the PDU enable switch to the off position.
Move the lockable switch on the PDU to the “O” or off
position.
Open the AC “mains” disconnect circuit breaker
supplying power to the Medalist x6000.
Once de-energized, the X-ray tube emits no radiation. After
a disaster that may have resulted in damage to the Medalist
x6000 shielding, an X-ray safety test of the Medalist x6000
must be performed prior to placing it back in operation.
Consult the Agilent Technologies Service Center before
attempting to return the Medalist x6000 to operation.
X
XX
X-
--
-Ray Control Off Button and X
Ray Control Off Button and XRay Control Off Button and X
Ray Control Off Button and X-
--
-Ray Control Key on the Ope
Ray Control Key on the OpeRay Control Key on the Ope
Ray Control Key on the Operator
rator rator
rator
Control Panel
Control PanelControl Panel
Control Panel
To de-energize the X-ray tube using the operator control
panel:
Press the X-ray Control off (0) button on the operator
control panel
Turn the X-ray Control key to the off (0) position on the
operator control panel.
NOTE

Rev. A
Rev. ARev. A
Rev. A Legal Notices, Warranty and Safety
Legal Notices, Warranty and SafetyLegal Notices, Warranty and Safety
Legal Notices, Warranty and Safety
xii
xiixii
xii
Figure 2 X-ray Control Off Button and X-Ray Control Key on the Operator Control Panel
PD Enable Switch and Lockable Breaker
PD Enable Switch and Lockable BreakerPD Enable Switch and Lockable Breaker
PD Enable Switch and Lockable Breaker
To de-energize the X-ray tube using the PDU enable switch
and lockable breaker:
Turn the PDU enable switch to the off position.
Move the lockable switch on the PDU to the O or off
position.
X-ray Control Key
in the Off Position
X-ray Control Off
Button

Rev. A
Rev. ARev. A
Rev. A Legal Notices, Warranty and Safety
Legal Notices, Warranty and SafetyLegal Notices, Warranty and Safety
Legal Notices, Warranty and Safety
xiii
xiiixiii
xiii
Figure 3 PDU Enable Switch and Lockable Breaker
AC
AC AC
AC “Mains” P
“Mains” P“Mains” P
“Mains” Power Disconnect
ower Disconnectower Disconnect
ower Disconnect
The AC “mains” power disconnect is a circuit breaker
typically installed by the end user and should be located
within 15 feet of the Medalist x6000 power distribution unit
(PDU). Local codes and needs will define the accessibility,
configuration, and size of this disconnect. This disconnect
will disconnect all power to the Medalist x6000.
!
0
1
0
1
Main disable can be locked in the “0”
Main disable can be locked in the “0” Main disable can be locked in the “0”
Main disable can be locked in the “0”
position.
position.position.
position.
Power Distribution nit
Power Distribution nitPower Distribution nit
Power Distribution nit

Rev. A
Rev. ARev. A
Rev. A Legal Notices, Warranty and Safety
Legal Notices, Warranty and SafetyLegal Notices, Warranty and Safety
Legal Notices, Warranty and Safety
xi
xixi
xiv
vv
v
7
7 7
7 X
XX
X-
--
-Ray Safety
Ray SafetyRay Safety
Ray Safety
This product produces X
This product produces XThis product produces X
This product produces X-
--
-rays. Do not attempt to open or modify any part of the product. Do not
rays. Do not attempt to open or modify any part of the product. Do not rays. Do not attempt to open or modify any part of the product. Do not
rays. Do not attempt to open or modify any part of the product. Do not
operate this product or turn on the X
operate this product or turn on the Xoperate this product or turn on the X
operate this product or turn on the X-
--
-ray source unless all shielding is in place. Operation without
ray source unless all shielding is in place. Operation without ray source unless all shielding is in place. Operation without
ray source unless all shielding is in place. Operation without
shiel
shielshiel
shielding in place can result in exposure to X
ding in place can result in exposure to Xding in place can result in exposure to X
ding in place can result in exposure to X-
--
-rays which can cause serious bodily injury or death.
rays which can cause serious bodily injury or death. rays which can cause serious bodily injury or death.
rays which can cause serious bodily injury or death.
Refer all servicing to service
Refer all servicing to serviceRefer all servicing to service
Refer all servicing to service-
--
-trained personnel.
trained personnel.trained personnel.
trained personnel.
Do not, for ANY
Do not, for ANYDo not, for ANY
Do not, for ANY reason, attempt to defeat the built
reason, attempt to defeat the built reason, attempt to defeat the built
reason, attempt to defeat the built-
--
-in safety interlocks. Operati
in safety interlocks. Operatiin safety interlocks. Operati
in safety interlocks. Operation without the
on without the on without the
on without the
Safety Interlock Subsystem functional can result in exposure to X
Safety Interlock Subsystem functional can result in exposure to XSafety Interlock Subsystem functional can result in exposure to X
Safety Interlock Subsystem functional can result in exposure to X-
--
-rays
raysrays
rays,
, ,
, high voltage
high voltagehigh voltage
high voltage, or moving
, or moving , or moving
, or moving
components
componentscomponents
components. Exposure to X
. Exposure to X. Exposure to X
. Exposure to X-
--
-rays
rays rays
rays and moving components
and moving components and moving components
and moving components can cause serious bodily injury
can cause serious bodily injurycan cause serious bodily injury
can cause serious bodily injury or
or or
or
death
deathdeath
death. Contact with high voltage can cause electrical sho
. Contact with high voltage can cause electrical sho. Contact with high voltage can cause electrical sho
. Contact with high voltage can cause electrical shock resul
ck resulck resul
ck resulting in serious bodily injury or
ting in serious bodily injury or ting in serious bodily injury or
ting in serious bodily injury or
death.
death. death.
death. Refer
Refer Refer
Refer all
allall
all servicing to service
servicing to service servicing to service
servicing to service-
--
-trained personnel.
trained personnel.trained personnel.
trained personnel.
Consult the
Consult the Consult the
Consult the Agilent Technologies Service Center
Agilent Technologies Service CenterAgilent Technologies Service Center
Agilent Technologies Service Center before attempting to service any components of
before attempting to service any components of before attempting to service any components of
before attempting to service any components of
the X
the Xthe X
the X-
--
-ray Subsystem.
ray Subsystem.ray Subsystem.
ray Subsystem.
Agilent recommends an x
Agilent recommends an xAgilent recommends an x
Agilent recommends an x-
--
-ray safety test be performed under the following conditions:
ray safety test be performed under the following conditions:ray safety test be performed under the following conditions:
ray safety test be performed under the following conditions:
every six (6) months,
every six (6) months,every six (6) months,
every six (6) months,
•when the Medalist x6000 is installed at a site,
when the Medalist x6000 is installed at a site,when the Medalist x6000 is installed at a site,
when the Medalist x6000 is installed at a site,
•when the Medalist x6000 has been moved,
when the Medalist x6000 has been moved,when the Medalist x6000 has been moved,
when the Medalist x6000 has been moved,
•immediately foll
immediately follimmediately foll
immediately following maintenance that involves the Safety Interlock Subsystem, the lead
owing maintenance that involves the Safety Interlock Subsystem, the lead owing maintenance that involves the Safety Interlock Subsystem, the lead
owing maintenance that involves the Safety Interlock Subsystem, the lead
shielding, the X
shielding, the Xshielding, the X
shielding, the X-
--
-ray
ray ray
ray t
tt
tube, or the HVPS.
ube, or the HVPS.ube, or the HVPS.
ube, or the HVPS.
Do not operate this equipment without complying to these recommendations.
Do not operate this equipment without complying to these recommendations.Do not operate this equipment without complying to these recommendations.
Do not operate this equipment without complying to these recommendations.
Verify that the X
Verify that the XVerify that the X
Verify that the X-
--
-ray
ray ray
ray tube
tubetube
tube has an exter
has an exter has an exter
has an external green ground wire going directly to the ground
nal green ground wire going directly to the ground nal green ground wire going directly to the ground
nal green ground wire going directly to the ground
connection on the X
connection on the Xconnection on the X
connection on the X-
--
-ray
ray ray
ray h
hh
high voltage power supply. This safety ground is in addition to the ground
igh voltage power supply. This safety ground is in addition to the ground igh voltage power supply. This safety ground is in addition to the ground
igh voltage power supply. This safety ground is in addition to the ground
supplied by the high voltage cable and the X
supplied by the high voltage cable and the Xsupplied by the high voltage cable and the X
supplied by the high voltage cable and the X-
--
-ray
ray ray
ray tube
tubetube
tube Mount.
Mount. Mount.
Mount.
Do not drill or
Do not drill orDo not drill or
Do not drill or modify the shielding panels in ANY way.
modify the shielding panels in ANY way. modify the shielding panels in ANY way.
modify the shielding panels in ANY way.
If X
If XIf X
If X-
--
-ray shielding is removed from the product or disturbed for any reason, the product must not
ray shielding is removed from the product or disturbed for any reason, the product must not ray shielding is removed from the product or disturbed for any reason, the product must not
ray shielding is removed from the product or disturbed for any reason, the product must not
be operated until the shielding is reinstalled and an X
be operated until the shielding is reinstalled and an Xbe operated until the shielding is reinstalled and an X
be operated until the shielding is reinstalled and an X-
--
-ray safety test (survey) is perf
ray safety test (survey) is perfray safety test (survey) is perf
ray safety test (survey) is performed by
ormed by ormed by
ormed by
trained personnel
trained personneltrained personnel
trained personnel
Do not place any
Do not place anyDo not place any
Do not place any strong magnets near the X
strong magnets near the X strong magnets near the X
strong magnets near the X-
--
-ray t
ray tray t
ray tube. Any magnets stronger than 50 gauss
ube. Any magnets stronger than 50 gauss ube. Any magnets stronger than 50 gauss
ube. Any magnets stronger than 50 gauss
placed immediately at the position of the deflection coils could cause the electron beam to hit
placed immediately at the position of the deflection coils could cause the electron beam to hit placed immediately at the position of the deflection coils could cause the electron beam to hit
placed immediately at the position of the deflection coils could cause the electron beam to hit
the side of th
the side of ththe side of th
the side of the X
e Xe X
e X-
--
-ray tube. The entire X
ray tube. The entire Xray tube. The entire X
ray tube. The entire X-
--
-ray t
ray tray t
ray tube is shielded in the
ube is shielded in the ube is shielded in the
ube is shielded in the Medalist x6000
Medalist x6000Medalist x6000
Medalist x6000 System, so, no
System, so, no System, so, no
System, so, no
additional radiation will be emitted from the system. However, proper operation of the machine
additional radiation will be emitted from the system. However, proper operation of the machine additional radiation will be emitted from the system. However, proper operation of the machine
additional radiation will be emitted from the system. However, proper operation of the machine
may
maymay
may not be possible in a strong magnetic field.
not be possible in a strong magnetic field. not be possible in a strong magnetic field.
not be possible in a strong magnetic field.
Do not apply pressure to, modify or damage the X
Do not apply pressure to, modify or damage the XDo not apply pressure to, modify or damage the X
Do not apply pressure to, modify or damage the X-
--
-ray vacuum window. The X
ray vacuum window. The Xray vacuum window. The X
ray vacuum window. The X-
--
-ray vacuum window
ray vacuum window ray vacuum window
ray vacuum window
supports the tungsten target material. If the X
supports the tungsten target material. If the Xsupports the tungsten target material. If the X
supports the tungsten target material. If the X-
--
-ray vacuum window is broken, the X
ray vacuum window is broken, the Xray vacuum window is broken, the X
ray vacuum window is broken, the X-
--
-ray
ray ray
ray tube
tubetube
tube will
will will
will
cease to operate.
cease to operate.cease to operate.
cease to operate.
WARNING
WARNING
WARNING
WARNING
CAUTION
CAUTION
WARNING
WARNING
WARNING