Agri-Fab 45-01762 User manual

• Safety
• Assembly
• Operation
• Maintenance
• Parts
CAUTION:
Read Rules for
Safe Operation
and Instructions
Carefully
OWNERS MANUAL
MODEL NO.
45-01762
7 CU. FT. FARM/YARD CART
PRINT D IN U.S.A. FORM NO. 47591 (R V. 6/99)
Digitally signed by WMV-Dresden
DN: cn=WMV-Dresden, c=DE,
o=WMV-Dresden,
[email protected]
Date: 2017.01.26 13:00:46 +01'00'
WMV-
Dresden

2
RULES FOR SAFE OPERATION
1/4" x 1"
1/4" x 2"
1/4" x 1-1/4"
3/4 x 1-1/2
1/4" WASHER 1/8" x 1-1/4"
1/4-20
TUBE CAP
ABCD
E
F
GI
FIGURE 1
ASSEMBLY INSTRUCTIONS
TOOLS R QUIR D
(1) Screw Driver
(1) Pliers
(1) 7/16" Wrench
When assembling your cart, place the heads of all
screws to the inside and hex nuts with flat washers
to the outside.
The bottom panel has one galvanized
edge; this is the rear. The front edge
has three holes. See figure 2.
NOTE
2. Line up three holes in bottom panel with holes in
front angle assembly. Start three 1/4" x 1" screws
through bottom panel, then through angle. Secure
screws with flat washers and hex nuts. Tighten
securely. See figure 2.
1. Lay the front angle assembly down (flat) on floor
and stand the bottom panel in position as shown in
figure 2.
FIGURE 2
HARDWARE REFERENCE CHART
Your Farm/Yard Cart carton contains a hardware
package with parts as shown in the chart below and in
figure 1.
REF. QTY. DESCRIPTION
A 8 Screws, 1/4-20 x 2" Long
B 4 Screws, 1/4-20 x 1-1/4" Long
C 13 Screws, 1/4-20 x 1" Long
D 4 Tube Cap, 1" x 1" Long
25 Hex Nuts, 1/4-20 Thread
F 25 Flat Washer, 1/4" I.D.
G 4 Flat Washers, 25/32" I.D. x 1-1/2" O.D.
I 2 Cotter Pins
Contents of Hardware Pack: (See figure 1)
Preventing accidents is the responsibility of every
equipment operator. The following general safety
precautions must be fully understood and followed by
every operator.
1. Do not at any time carry passengers in this cart. It
is designed for carrying materials only and not
intended to carry passengers.
2. Be careful on any grade (hill) and stay off of steep
grades.
3. Use caution when loading cart to avoid tipping.
4. Avoid large holes and ditches when transporting
loads.

3
3. Turn the front angle assembly and bottom panel
upside down as shown in figure 3.
4. Lay the two side angles on the bottom panel so
that the axle sleeves are closer to the front angle
assembly. See figure 3.
5. Secure both side angle assemblies to the bottom
panel using six 1/4" x 1" screws, flat washers and
hex nuts. Make only finger tight until all six screws
are in place, then tighten securely. See figure 3.
FIGURE 4
FIGURE 5
8. Lay the front panel down onto the front angle
assembly, on top of the four large washers. See
figure 5.
FIGURE 3
6. Stand the cart on its front end with the front angle
assembly on the floor. See figure 4.
7. Temporarily place four large 1-1/2" dia. flat wash-
ers (used on wheel axle) on the inside of front
angle assembly. See figure 4.
These washers act as shims and are
just for assembly purposes. You will
remove them later to use on axle.
NOTE

4
9. Place one side panel in position against a side
angle and down on top of the front panel. Start one
1/4" x 1" screw through the center hole in side
panel and side angle. Secure with hex nut and flat
washer. See figure 6. Make only finger tight at
this time.
10. Start one 1/4" x 1-1/4" screw through front hole on
side panel and side angle. Start another 1/4" x 1-1/4"
screw through top hole on side panel and front
angle assembly. Next, place a support strap over
these two screws and secure it with flat washers
and hex nuts, making only finger tight at this
time. See figure 6.
11. Repeat steps 9 and 10 for the other side panel.
12. Assemble one 1/4" x 1" screw through bottom hole
in side panel and front angle assembly. Secure
with a flat washer and hex nut, making only
finger tight at this time. See figure 7.
13. Repeat step 12 for the other side panel.
14. Place the axle through axle sleeves as shown in
figure 7. Refer also to figure 11 on page 5. Tighten
all loose nuts and screws securely at this time.
FIGURE 7
FIGURE 8
15. Lay the cart down on the floor so that the sides are
up in a normal position. Remove the front panel by
sliding it up, then remove the four large washers
you used for shims. See figure 8.
FIGURE 6

5
16. Stand cart up on its front end again. Place tube
caps on leg tube and assemble the leg tube as
shown in figure 9, using four 1/4" x 2" screws
through side panels and leg tube. Secure with flat
washers and hex nuts. See figure 9.
FIGURE 10
19. Lay the cart upside down so that the axle is on top.
See figure 11.
FIGURE 11
FIGURE 9
17. Leave the cart standing to assemble the handle
tube in the next step.
18. Place tube caps on the handle tube, then place it
over the side panels and line up the four holes.
Assemble four 1/4" x 2" screws through the side
panels and handle. Secure with flat washers and
hex nuts. See figure 10.

6
FIGURE 12
21. Turn cart right side up, so that it rests on its
wheels.
22. Place front panel in guides to complete assembly.
23. Your cart is now ready to use.
MAINTENANCE
1. Grease or oil wheel bearings occasionally. Use
automotive wheel bearing type grease or 20 weight
oil.
2. Periodically retighten all screws, especially after
heavy use. Do not exceed load capacity rating
of 300 lbs.
3. Clean cart thoroughly after each use.
4. Store indoors during severe weather.
5. Apply light coat of varnish to all wood surfaces
annually.
6. Use glossy black enamel spray paint to touch up
scratched or worn painted metal surfaces.
If cotter pin can not be assembled through
hole in the axle ends, remove one washer
from inside, next to axle sleeve.
NOTE
20. Place one 1-1/2" dia. flat washer on the axle, then
a wheel and then one more 1-1/2" dia. flat washer.
Secure wheel to axle with a cotter pin. See figure
12 and note below. Repeat step for other wheel.

7
MODEL 45-01762 7 CU. FT. FARM/YARD CART
*Purchase Common Hardware Locally.
R F. PART QTY. D SCRIPTION
NO. NO.
R F. PART QTY. D SCRIPTION
NO. NO.
PARTS LIST FOR MODEL NO. 45-01762 FARM/YARD CART
1 47585 1 Front Panel
2 47586 2 Side Panel
3 47587 1 Bottom Panel
4 62527 1 Side Angle Assembly, L.H.
5 62528 1 Side Angle Assembly, R.H.
6 62529 1 Front Angle
7 44018 1 Handle Tube
8 44019 1 Leg Tube
9 23606 2 Support Strap
10 44975 2 Wheel Assembly Complete
w/Bearings (20")
11 44021 4 Tube Caps
12 43010 2 Cotter Pin, 1/8" x 1-1/4" Lg.*
13 43949 4 Flat Washer 25/32" I.D. x 1-1/2" O.D.
x 3/32" Thick
14 47584 8 Truss Head Screws 1/4-20 x 2" Lg.*
15 44259 13 Truss Head Screws 1/4-20 x 1" Lg.*
16 43088 25 Flat Washer, 1/4" I.D.*
17 43178 25 Hex Nut, 1/4-20 Thread *
18 23991 1 Axle
19 44016 4 Bearing, Ball 3/4" I.D.
20 44020 4 Truss Head Screws 1/4-20 x 1-1/4" Lg.*
47591 1 Owner's Manual

REPAIR PARTS
303 West Raymond
Sullivan, IL. 61951
217-728-8388 / www.agri-fab.com