Agri-Fab 45-0267 User manual

SAFETY PRECAUTIONS
1. Never attach a garden hose to the fill/drain hole
when filling. Dangerous pressure build up could
occur inside roller.
2. Do not fill roller to maximum weight without check-
ing capability of vehicle to safely pull and stop.
3. ever use roller up and down hills; always work across
hills and slopes.
4. Use caution when turning, slowing or stopping.
5. Always drain roller to keep from freezing.
OWNERS
MANUAL
MODEL NO.
45-0267
POLY LAWN ROLLER
(18" Dia. x 24" Wide)
Assembly instructions on reverse side.
SPECIFICATIONS:
Roller Drum: 18" Dia. x 24" Wide, H.D. Polyethylene
O.A. Width: Approx. 29-1/2"
Bearings: 3/4" I.D., Replaceable
Tow Hitch: Std. Pin Type - 1/2" Hole
Weight w/ Water: Up to 240 Lbs. Filled with Water
( ote: May be filled with sand)
Approx. Sh. Wt.: 30 Lbs.

ASSEMBLY INSTRUCTIONS
(SEE ILLUSTRATION BELOW)
Printed in USA Form o. 46840 (Rev. 1/97)
REPAIR PARTS
303 W. Raymond St.
Sullivan, IL. 61951
[phone]
1 46844 1 Lawn Roller Ass'y
2 24222 1 Scraper Bar
3 46841 2 Side Tube
4 46842 1 Handle Tube
5 24221 1 Tow Hitch Bracket (Clevis)
6 46838 2 Spacer Tube
Part
No. Qty. Description
Ref.
No. Description
7 44798 2 ylon Flange Bearing
8 43009 4 Washer, 1.59" x 25/32"
9 43224 1 Hex Bolt, 5/16-18 x 2-1/4"
10 43084 6 Hex Bolt, 5/16-18 x 1-3/4"
11 43064 7 Hex Lock ut, 5/16-18
12 43709 1 Plug, Lawn Roller
Qty.
Part
No.
Ref.
No.
PARTS LIST FOR POLY LAWN ROLLER - MODEL 45-0267
NOTE: Do not tighten until all bolts are assembled.
1. Assemble a washer (Ref. 8), a spacer tube (Ref. 6)
and another washer (Ref. 8) onto each end of the
roller.
2. Assemble a flange bearing (Ref. 7) through each side
tube (Ref. 3) so that the flange end of the bearing
will face toward the roller. (To assemble, you may
need to carefully tap against the flange bearing with
a block of wood or a hammer.)
1
2
11
11
867
10
10
10
768
12
3
3
4
5
8
8
9
10
11
11
11
3. Place the side tubes (Ref. 3) onto both ends of the
roller. Assemble the scraper bar (Ref. 2) to the side
tubes using two hex bolts (Ref. 10) and hex lock nuts
(Ref. 11).
4. Assemble the side tubes (Ref. 3) to the handle tube
(Ref. 4) using four hex bolts (Ref. 10) and hex lock
nuts (Ref. 11).
5. Assemble the tow hitch bracket (Ref. 5) to the handle
tube (Ref. 4) using one hex bolt (Ref. 9) and hex
lock nut (Ref. 11). The bracket is shown in the tow
position. For a push roller, remove the bracket or
reverse its position. Tighten all bolts at this time.