Agri-Fab H.D. Lawn Roller 45-02163 User manual

OWNERS
MANUAL
MODEL NO.
45-02164
45-02163
H.D. LAWN ROLLER
(24" Dia. x 48" Wide)
SAFETY PRECAUTIONS
1.
Never
attach a garden hose to the fi ll/drain hole when
fi lling. Dangerous pressure build up could occur inside
roller.
2. Do not fi ll roller to maximum weight without checking
capability of vehicle to safely pull and stop.
3. Never use roller up and down hills; always work across
hills and slopes.
4. Use caution when turning, slowing or stopping.
5. Always drain roller to keep from freezing.
SPECIFICATIONS:
Roller Drum:
24" Dia. x 48" Wide Welded Steel
O.A. Width:
Approximately 52"
Bearings:
1" I.D., Replaceable
Tow Hitch:
Std. Pin Type - 1/2" Hole
Weight w/ Water:
Up to 910 Lbs. Filled with Water
(Note: May be fi lled with sand)
Approx. Sh. Wt.:
Approximately 165 Lbs.
Printed in USA
© 2004 Agri-Fab, Inc.
Form No. 40255 (9/06)
™

REPAIR PARTS
Agri-Fab, Inc.
809 South Hamilton
Sullivan, IL. 61951
217-728-8388
www.agri-fab.com
1 ----- 1 Roller Drum (Not sold separately)
2 24868 1 Scraper Bar
3 48376 2 Hitch Tube
4 24192 2 Hitch Bracket
5 43632 2 Bearing, Plastic
6 43528 2 Flat Washer, 1"
7 46782 2 Hex Bolt, 5/16-18 x 3"
1 ----- 1 Roller Drum (Not sold separately)
2 24868 1 Scraper Bar
3 48376 2 Hitch Tube
4 24192 2 Hitch Bracket
5 43632 2 Bearing, Plastic
6 43528 2 Flat Washer, 1"
7 46782 2 Hex Bolt, 5/16-18 x 3"
8 43224 2 Hex Bolt, 5/16-18 x 2-1/4"
9 43084 2 Hex Bolt, 5/16-18 x 1-3/4"
10 47810 6 Hex Lock Nut, 5/16-18
11 49467 2 Plug, Lawn Roller
12 43501 2 Cotter Pin, 5/32" x 1-1/2"
13 47623 1 Hitch Pin
14 43343 1 Hair Cotter Pin 1/8"
1 ----- 1 Roller Drum (Not sold separately)
2 24868 1 Scraper Bar
3 48376 2 Hitch Tube
4 24192 2 Hitch Bracket
5 43632 2 Bearing, Plastic
6 43528 2 Flat Washer, 1"
7 46782 2 Hex Bolt, 5/16-18 x 3"
1 ----- 1 Roller Drum (Not sold separately)
2 24868 1 Scraper Bar
3 48376 2 Hitch Tube
4 24192 2 Hitch Bracket
5 43632 2 Bearing, Plastic
6 43528 2 Flat Washer, 1"
7 46782 2 Hex Bolt, 5/16-18 x 3"
8 43224 2 Hex Bolt, 5/16-18 x 2-1/4"
9 43084 2 Hex Bolt, 5/16-18 x 1-3/4"
10 47810 6 Hex Lock Nut, 5/16-18
11 49467 2 Plug, Lawn Roller
12 43501 2 Cotter Pin, 5/32" x 1-1/2"
13 47623 1 Hitch Pin
14 43343 1 Hair Cotter Pin 1/8"
8 43224 2 Hex Bolt, 5/16-18 x 2-1/4"
9 43084 2 Hex Bolt, 5/16-18 x 1-3/4"
10 47810 6 Hex Lock Nut, 5/16-18
11 49467 2 Plug, Lawn Roller
12 43501 2 Cotter Pin, 5/32" x 1-1/2"
13 47623 1 Hitch Pin
14 43343 1 Hair Cotter Pin 1/8"
8 43224 2 Hex Bolt, 5/16-18 x 2-1/4"
9 43084 2 Hex Bolt, 5/16-18 x 1-3/4"
10 47810 6 Hex Lock Nut, 5/16-18
11 49467 2 Plug, Lawn Roller
12 43501 2 Cotter Pin, 5/32" x 1-1/2"
13 47623 1 Hitch Pin
14 43343 1 Hair Cotter Pin 1/8"
Ref. Part Qty. Description
Ref. Part Qty. Description
Ref. Part Qty. Description
Ref. Part Qty. Description
Ref. Part Qty. Description
No. No.
No. No.
No. No.
Ref. Part Qty. Description
Ref. Part Qty. Description
Ref. Part Qty. Description
Ref. Part Qty. Description
No. No.
No. No.
ASSEMBLY INSTRUCTIONS
(SEE ILLUSTRATION BELOW)
1. Assemble bearings (Ref. 5) into hitch tubes (Ref. 3) so
that bearing fl ange is against outside of hitch tube. (You
may need to place a block of wood against bearing and
carefully tap with a hammer.)
2. Place hitch tubes (Ref. 3) onto both ends of roller shaft.
Assemble a fl at washer (Ref. 6) onto each end of roller
shaft and secure with two cotter pins (Ref. 12).
3. Assemble scraper bar (Ref. 2) to hitch tubes (Ref. 3)
using two hex bolts (Ref. 9) and hex lock nuts (Ref. 10).
Do not tighten yet.
4. Assemble ends of hitch tubes (Ref. 3) together using
two hex bolts (Ref. 7) and hex lock nuts (Ref. 10).
Do
not tighten yet.
5. Assemble hitch brackets (Ref. 4) to hitch tubes (Ref. 3)
using two hex bolts (Ref. 8) and hex lock nuts (Ref. 10).
Do not tighten yet.
6.
Tighten
bolts and nuts starting with scraper bar (Ref.
2), then ends of hitch tubes (Ref. 3), and fi nally hitch
brackets (Ref. 4).
7. Install hitch pin (Ref. 13) through hitch brackets (Ref. 4)
and secure with hair cotter pin (Ref. 14).
8
.
Adjust plug (Ref. 11) size by twisting handle. Lock a plug
in each end of roller drum by fl ipping handle down.
1
6
5
9
3
10
4
8
10
7
3
9
5
6
11
2
10
10
11 12
12
13
14
ADJUST SIZE
the fastest way to purchase parts
www.speedepart.com