Aiphone GF-MK User manual

-1-
FK0979 1002 B
SECURITY GUARD STATION
Model: GF-MK
INSTALLATION & OPERATION MANUAL
PRECAUTIONS
GENERAL PRECAUTIONS
(Negligence could result in death or serious
injury to people.)
WARNING
CAUTION
(Negligence could result in injury to people
or damage to property.)
General Prohibitions Prohibitions to subject
the unit to water
Prohibitions to
dismantle the unit
1. Do not open the unit case.
2. Do not dismantle or alter the unit. Fire or electric shock
could results.
3. Keep the unit away from water or any other liquid.
Fire or electric shock could result.
4. Do not put any metal into the unit through openings.
Fire, electric shock or unit trouble could result.
Do not install the unit in any of the following locations, as 
it may cause the system to malfunction;
- High or extreme cold temperature area: under direct sunlight,
near equipment that varies in temperature, in front of air
conditioner, inside a refrigerated area, etc.
- Places subject to moisture or humidity extremes.
- Places subject to environmental conditions, 
such as oil, dust, chemicals, salt, etc.
- Places subject to constant vibration or impact.
- Places subject to steam or smoke, such as near heating
appliances, cooking surface, etc.
1. All the units, except the Entrance Station, is designed for
indoor use only. Do not install them outdoors.
2. The system is not operable during a power failure.
3. In areas where broadcasting station antennas are close
by, intercom system may be affected by radio frequency
interference.
4. Keep all wiring at least 30cm (1") away from AC 100-240V
wiring, fluorescent lighting, or dimmer switches.
Otherwise, cross AC wiring at a 90¡ angle.
1. Mount the unit on wall in a convenient location, but not
where it could be bumped or jarred.Injury could result.
2. Do not install or make any wire terminations while power
supply is turned on. Unit trouble could result.
3. Before turning on power supply, make sure wires are not
crossed or shorted. Unit trouble could result.
4. Do not manually hold down hook switch to verify chime
volume. It sounds very loud near your ears and can
cause your hearing damage.
5. Do not press hard or put high impact on LCD. If glass
cover is broken, you may be injured, and never touch the
liquid inside panel, as it can cause an inflammation on
your skin. If the liquid adheres to any part of your body,
mouth or eyes, immediately gargle or cleanse with clear
water for at least 15 minutes and consult your doctor.
Calling & Communication
a. with Residential Stations.
b. with Entrance Station.
c. with Security Guard Station.
d. PANIC call & Answer-back.
( ＊ Includes Line-off trouble alarm)
Programming by PC
¥ It is possible to write or change resident names
from your PC, making data input.
¥ Download Programming & Alteration Method
from Aiphone's Web Site:
http://www.aiphone.com/
¥ Connect your PC with GF-MK in conjunction with
the connecting cable supplied with GF-MK.
Programming by GF-MK
¥ On LCD display, see a message "AIPHONE" to
confirm system is in standby.
¥ Prior to programming, it is suggested to have
your own ID code newly registered, so that any
other person cannot get into the system.
¥ Firstly, enter program mode.
¥ In case your programmed ID code is forgotten,
NAMES AND FUNCTIONS
GF-MK
COMMUNICATION FUNCTIONSPROGRAMMING METHODS
a
b
Security Guard Stations 1 & 2
Entrance
Station Residential Stations
PANIC CALL
Switch
c
d
M
¥ Security Guard Station (GF-MK)
¥ Mounting bracket
¥ Packet of screws
¥ Connecting cable
¥ INSTALLATION & OPERATION
MANUAL
PACKAGE CONTENTS
Go to P.2
Go to P.4
Go to P.6
Go to P.6
Go to P.5
Go to P.8
10. DOOR RELEASE button
11. Off-hook warning LED
12. Call tone sounder
13. Call tone volume control
14. PC socket
2
B
A
C
13
E
D
F
5
K
J
L
4
H
G
I
6
N
M
O
8
U
T
V
7
R
Q
P
S
Y
X
W
Z
9
0
2
B
A
C
13
E
D
F
5
K
J
L
4
H
G
I
6
N
M
O
8
U
T
V
7
R
Q
P
S
Y
X
W
Z
9
0
1. Handset
2. LCD display
3. CANCEL (or decide & back)
4. SCROLL backward or move cursor to left
5. SCROLL forward or move cursor to right
6. CALL (or decide & next)
7. Digital keypad (1 ~ 0, , #)
When entering letters; A~Z,0=[,][-][.][/][ ]
Functions : ¥ Dialing Room #
¥ Name search with key and calling
8. SERVICE button (Option)
9. LIGHT button When communication with
Entrance Station, press to
turn on external light.
Configure your GF Security Guard Station system with GF-MK-compatible components;
GF-1DK, GF-1MDK for Residential Stations (not GF-1D or GF-1MD),
GF-DA/ B for Audio module (not GF-DA/A), and
GF-NS/A for Digital name scroll module (not GF-NS).
1
8
2
3
4
7
6
5
9
10
12
13
14
11
or
6.
GF-MK07.1.309:07AMページ1

- 2 -
PROGRAMMING
Enter Program Mode
AIPHONE
111
1
INITIAL ID CODE
{
{
111
1
INITIAL ID CODE
LCD
Select Menu & Quit
YOUR OPERATION
RE-ENTER ID CODE
YOUR OPERATION
Menu 1: Select language
ENGLISH
FRANCAIS
DEUTSCH
ESPANOL
NEDERLANDS
SELECT LANGUAGE
ENGLISH
YOUR OPERATION
LCD
MENU
FORWARD
Scroll
BACKWARD
Menu 2
Menu 3
SELECT LANGUAGE
2
B
C
13
E
D
F
3
E
D
F
0
Menu 2: Change ID code
Enter new ID code
CHANGE ID CODE
NEW ID (4-digit)
INITIAL ID
CHANGE ID CODE
1111
CHANGE ID CODE
YOUR OPERATION
A
LCD
Menu 3: Write Residence Info. Menu 4: Set imput timeout timer
11
0
RESIDENCE INFO.
ROOM #
3-or 4-digit
{
{
101
Enter a name 'SMITH' (example)
7
R
Q
P
S
......
7
R
Q
P
S
7
R
Q
P
S
7
R
Q
P
S
SM
O
N
M
6
Enter ROOM #
Menu 5
Menu 4
YOUR OPERATION
LCD
2-digit (15-99)
{
PROGRAM TIMER
60
0
0
Y
X
W
Z
9
SET TIMER
OPERATION TIMER
15
2-digit (30-99)
{
YOUR OPERATION
LCD
Move cursor
TO RIGHT
TO LEFT
Move cursor
TO RIGHT
TO LEFT
DECIDE & BACK
DECIDE & BACK
DECIDE & NEXT
DECIDE & BACK DECIDE & BACK
DECIDE & BACK
101
SMITH
SELECT LANGUAGE
LCD
MENU
Standby
FORWARD
Scroll
BACKWARD
SELECT LANGUAGE
CHANGE ID CODE
SET TIMER
RESIDENCE INFO.
PROGRAMMING 〈〈
QUIT
Go to Menu 1-5
}
(
DECIDE & NEXTDECIDE & NEXT
DECIDE & NEXT
DECIDE & NEXT
DECIDE & NEXT
DECIDE & NEXT
DECIDE & NEXT
IDCODE=+4digit
IDCODE=+4digit
{
1
2
3
4
5
6
0123
While being programmed, PANIC CALL is not receivable on GF-MK.
CLEAR
Note: Press to clear the previous name
and enter a new name.
GF-MK07.1.309:07AMページ2

- 3 -
Menu 5: Programming 〈〈
PROGRAMMING 〈〈
DECIDE & BACK
PROGRAMMING 〈〈
CONNECTING …
DECIDE & NEXT
NOTES;
If already two Residential Stations have been linked, setting a third station will produce a warning beep tone.
To erase linkage have the assigned name displayed, press CALL button more than 3 seconds.
Continuous tone notifies the link has been cancelled.
Before initiating PROGRAMMING 〈〈 operation, make sure ROOM number has been programmed on Menu RESIDENCE INFO.
Lift the handset
(Security Guard Station)
Hearing single BEEP tone means the station has been correctly set.
(Double beep tone for second station)
Hang up handset.
Go to each Residential stations, and consecutively program each handset station in the same manner as in Programming Step.
Programming Step
2
B
A
C
13
E
D
F
5
K
J
L
4
H
G
I
6
N
M
O
8
U
T
V
7
R
Q
P
S
Y
X
W
Z
9
0
At an Residential Station number 1, lift handset.
Communication channel is established.
DECIDE & BACK
QUIT
2
B
A
C
13
E
D
F
5
K
J
L
4
H
G
I
6
N
M
O
8
U
T
V
7
R
Q
P
S
Y
X
W
Z
9
0
101
AIPHONE
With Scroll buttons,
have the assigned
Name displayed,
and press button.
2
B
A
C
13
E
D
F
5
K
J
L
4
H
G
I
6
N
M
O
8
U
T
V
7
R
Q
P
S
Y
X
W
Z
9
0
Standby
2
B
A
C
13
E
D
F
5
K
J
L
4
H
G
I
6
N
M
O
8
U
T
V
7
R
Q
P
S
Y
X
W
Z
9
0
Beep
While connecting date to the system, whole system is not operatable including PANIC CALL.
Hang up handset.
(Security Guard station)
PROGRAMMING 〈〈
CONNECTING …
GF-MK07.1.309:07AMページ3

- 4 -
2
Call tone sounds for
approximately 10
seconds.
3
Lift the handset to reply within
approximately 45 seconds.
Communicate with the
Security Guard Station.
At Security Guard Station
Lift the handset, have the name
displayed, and press Call button.
(See below)
At Residential Station
1 4
WITH RESIDENTIAL STATION
Calling a Residential Station
Notes; ●When pressing and holding down SCROLL ▲or ▼button for
approximately 2 seconds, resident names will be shown
automatically at every 0.4 seconds.
●When ROOM #111 and 1111 are both present, enter 1,1,1 and the
Resident name for 111 will be displayed, and press 1 one more
time, and the name for ROOM 1111 will be displayed.
2
B
A
C
13
E
D
F
5
K
J
L
4
H
G
I
6
N
M
O
8
U
T
V
7
R
Q
P
S
Y
X
W
Z
9
0
When finished, hang up handset.
Communication will automatically
turn off in approximately 2.5
minutes.
Press button intermittently
or hold down for 2 sec. to
show in succession.
1. Calling
(2)By Dialling a Room Number
1
0
Press ROOM #.
AIPHONE AIPHONE
CALL
CALLING
SMITH
CALLING
SMITH
1
When there is no Room #,
• When there is no name, (example: A)
NO ENTRY
LCD YOUR OPERATION LCD
FORWARD
Scroll
BACKWARD
YOUR OPERATION
NO ENTRY : A
2. Communication (common operation)
The channel is turned off in approx.
2-1/2 min.
OR Press
(3)By Selecting Name Entering Alphabets
'SMITH' (example)
Apartment station
lifts handset.
CALL
ENTER A LETTER
AIPHONE CALLING
SMITH
IN COMMUNICATION
Communicate
AIPHONE
CALLING
SMITH...
CANCEL
LCD YOUR OPERATION LCD
ENTER
YOUR OPERATION
(1)By Scrolling Names
CALL
{
7
R
Q
P
S
7
R
Q
P
S
7
R
Q
P
S
7
R
Q
P
S
S
...
101
SMITH
101
SMITH
101
SMITH
Receiving a call from Residential station
Lift the handset, then press Security
Guard CALL button. Muted call tone
is heard. When the system is busy
with a communication, the Residential
Station will hear a busy tone.
(When any linkage has not been
established, the call is just nullified.)
Security
Guard
CALL button
12 Lift the handset, and
communicate.
34
At Residential Station At Security Guard Station
Call tone rings for approximately
10 seconds, and ROOM No. &
Resident's NAME are displayed.
Lift handset and reply.
Notes;
In case two Security Guard Station are
linked, another Security Guard Station turns
off andIN USEis displayed on LCD.
2
B
A
C
13
E
D
F
5
K
J
L
4
H
G
I
6
N
M
O
8
U
T
V
7
R
Q
P
S
Y
X
W
Z
9
0
When finished, hang
up handset.
Communication will
automatically turn off
in approximately 2.5
minutes.
2
B
A
C
13
E
D
F
5
K
J
L
4
H
G
I
6
N
M
O
8
U
T
V
7
R
Q
P
S
Y
X
W
Z
9
0
2
B
A
C
13
E
D
F
5
K
J
L
4
H
G
I
6
N
M
O
8
U
T
V
7
R
Q
P
S
Y
X
W
Z
9
0
Note: SeeIN USEis not displayed.
GF-MK07.1.309:07AMページ4

- 5 -
WITH ENTRANCE STATION
Requires name registration and linkage.
12
Momentarily depress
a Call button.
Muted call tone is
heard from the
Entrance Station.
1
When finished, hang up the handset.
Communication will automatically turn off
in approximately 2.5 minutes.
Call tone rings for
approximately 10
seconds, and ROOM
No. & Resident's NAME
are displayed. Lift
handset and reply.
External light turns on
at the entrance for a
preprogrammed
length of time.
At the communicating
entrance station, door
release is activated.
Momentarily depress DOOR
RELEASE button.
Momentarily press LIGHT button.
At Entrance Station At Security Guard Station
Door Release
3'
4
4'
3
Turn on Entrance Light
While communicating,
Normal
call tone
2
B
A
C
13
E
D
F
5
K
J
L
4
H
G
I
6
N
M
O
8
U
T
V
7
R
Q
P
S
Y
X
W
Z
9
0
DOOR
RELEASE
button
LIGHT
button
2
B
A
C
13
E
D
F
5
K
J
L
4
H
G
I
6
N
M
O
8
U
T
V
7
R
Q
P
S
Y
X
W
Z
9
0
Press a numeric button (1-5) to select the
Entrance Station desired.
2
34
Press CALL button, and talk to the
Entrance Station.
When there is no corresponding Entrance
Station, a message NO ENTRY appears
on upper case.
While communicating, LIGHT & DOOR
RELEASE buttons are operative.
When finished, hang up handset.
Communication will automatically turn off
in approximately 2.5 minutes.
Receiving a call from Entrance Station
2
B
A
C
13
E
D
F
5
K
J
L
4
H
G
I
6
N
M
O
8
U
T
V
7
R
Q
P
S
Y
X
W
Z
9
0
2
B
A
C
13
E
D
F
5
K
J
L
4
H
G
I
6
N
M
O
8
U
T
V
7
R
Q
P
S
Y
X
W
Z
9
0
2
B
A
C
13
E
D
F
5
K
J
L
4
H
G
I
6
N
M
O
8
U
T
V
7
R
Q
P
S
Y
X
W
Z
9
0
Does not require name registration or linkage.
Calling Entrance Station
Lift the handset and press , ① button.
X
X
Note; When entering only, the
message is ENTER A LETTER,
as is common operation entering
an alphabet in searching name.
2
B
A
C
13
E
D
F
5
K
J
L
4
H
G
I
6
N
M
O
8
U
T
V
7
R
Q
P
S
Y
X
W
Z
9
0
Note: SeeIN USEis not displayed.
GF-MK07.1.309:07AMページ5

- 6 -
2
B
A
C
13
E
D
F
5
K
J
L
4
H
G
I
6
N
M
O
8
U
T
V
7
R
Q
P
S
Y
X
W
Z
9
0
BETWEEN SECURITY GUARD STATIONS
2
B
A
C
13
E
D
F
5
K
J
L
4
H
G
I
6
N
M
O
8
U
T
V
7
R
Q
P
S
Y
X
W
Z
9
0
Lift the handset, press , ① buttons.
Press 0 button, and CALL button.
Muted call tone is heard from handset receiver.
1
At Calling Station
Notes: SeeIN USEis not displayed at start of operation.
When entering only, the message is ENTER A LETTER, as is common operation entering an alphabet in searching name as well.
When no Security Guard Station is registered, a message NO ENTRY comes on.
X
PANIC CALL
2
B
A
C
13
E
D
F
5
K
J
L
4
H
G
I
6
N
M
O
8
U
T
V
7
R
Q
P
S
Y
X
W
Z
9
0
Beep,
Beep,
Beep
Call tone
Beep,
Beep,
Beep
3
5
Lift the handset and
communicate with
Security Guard Station.
6
2
Alarm sounds from
Residental Station. Push PANIC
CALL switch*
to lock.
1
Unlock PANIC CALL switch
to place in standby.
7
After communication, PANIC CALL
alarm sounds comes back on.
At Security Guard Station At Residential Station
4
Lift the handset, see the name on
LCD display, and press RESIDENCE
CALL button.
8
Press CANCEL button to clear signal.
PANIC CALL answer-back
X
Or Line-off trouble takes place
Notes;
Restores to normal.
*Varies by model.
*Varies by model.
Alarm sounds, and
ROOM No. and
EMERGENCY with
Resident NAME.
are displayed alternatly.
Stop alarm by pressing
CANCEL button.
The alarm turning to normal
call tone, sounds for
approximately 45 seconds.
2
B
A
C
13
E
D
F
5
K
J
L
4
H
G
I
6
N
M
O
8
U
T
V
7
R
Q
P
S
Y
X
W
Z
9
0
1. When one Security Guard Station is already engaged in PANIC CALL and communication, the other Security Guard Station can not break in.
(The busy tone is heard from the handset receiver.)
2. At the Security Guard Station, either answer-back to a PANIC CALL originated Residential Station, or normal calling to other Residential
Station is selectable. (Only name scroll buttons are not operational.) When the system is occupied, it can not operate.
3. At the Residential Station, the PANIC CALL alarm sounds at the HIGH level regardless of adjusting of volume control.
4. Even when the system is occupied, PANIC CALL can be activated. (Up to 10 Residential Stations can be linked with Security Guard Station.
5. Security Guard Station, when received multiple PANIC CALLs, will have NEXT ALARM message displayed.
6. When the Arrow message is present, it is possible to select other Residential Stations with SCROLL buttons.
7. Even when system is occupied, PANIC CALL answer-back initiates after the other communication is turned off.
8. At the Residential Station in same room, while sounding PANIC CALL signal, normal call or doorbell call can not be received.
Answer-back from Security Guard Station is only available.
X
GF-MK07.1.309:07AMページ6

- 7 -
Strip cable jackets, and put all the wires neatly
into slot, otherwise damages the wires by
pinching.
Notes;
To detach terminal block;
Slide and pull out the terminal block.
Cut out a hole for surface cable run.
Unplug
Terminal block
Cable slot
Modular
plug Round gang-box
OR
Single-gang box
Mounting
bracket
60mm (2-3/8")
83.5mm (3-5/16")
2
B
A
C
13
E
D
F
5
K
J
L
4
H
G
I
6
N
M
O
8
U
T
V
7
R
Q
P
S
Y
X
W
Z
9
0
It is suggested to mount the station so that the LCD display comes at the user's eye level.
1. Attach the mounting bracket to Single-gang box.
2. Connect wires on terminal block.
3. Mount the unit on mounting bracket.
Wall-mounting
WIRING
MOUNTING
1. Separate mounting bracket on
back of the unit.
2. Attach mounting bracket to
GFW-S stand as shown.
4. Place protection cover on
terminal section. 5. Insert prongs of bracket and
slide upward until locked.
Desk-top mounting on GFW-S stand
2
B
A
C
13
E
D
F
5
K
J
L
4
H
G
I
6
N
M
O
8
U
T
V
7
R
Q
P
S
Y
X
W
Z
9
0
Unit cable with stand hook by convex to prevent to death by
pulled out.
3. Connect wires on terminal block, putting wires neatly in the slot.
• Desk-top stand (GFW-S)
•Packet of screws
•Convex
GFW-S (not included)
PACKAGE CONTENTS
SW, SW: to User-option device
(Non-polarized)
Terminal block
(
from left R1, R2; R1, R2; C, CE; SW, SW)
to Doorbell
to next GF-1MDK
GF-1MDK
GF-1DK
to Doorbell
PANIC CALL
switch ( )
（＊）PANIC CALL switch: locally available
（w/break contact）
C, CE: to Doorbell button
(Non-polarized)
R1, R2: to Second GF-MK
(Non-polarized)
R1, R2: to Distribution point
(Non-polarized)
2
B
A
C
13
E
D
F
5
K
J
L
4
H
G
I
6
N
M
O
8
U
T
V
7
R
Q
P
S
Y
X
W
Z
9
0
GF-BC
GF-MK Back view
R1
R1
R1 R2
R1 R2 R1 R2
B1 B2 B1 B2 C CE K KE
R2
C
CE
K
KE
R2
GF-VBC
IN OUT OUT
IN
PANIC CALL
switch ( )
Screw ( 4) supplied
with GFW-S
GF-MK07.1.309:07AMページ7

Printed in Thailand (E)
AIPHONE CO., LTD., NAGOYA, JAPAN
AIPHONE CORPORATION, BELLEVUE, WA, USA
AIPHONE EUROPE N.V., ANTWERP, BELGIUM

WARRANTY
Aiphone warrants its products to be free from defects of material and workmanship under normal use and service for a period of
one year after delivery to the ultimate user and will repair free of charge or replace at no charge, should it become defective
upon which examination shall disclose to be defective and under warranty. Aiphone reserves unto itself the sole right to make
the final decision whether there is a defect in materials and/or workmanship; and whether or not the product is within the
warranty.
This warranty shall not apply to any Aiphone product which has been subject to misuse, neglect, accident, or to use in violation
of instructions furnished, nor extended to units which have been repaired or altered outside of the factory. This warranty does
not cover batteries or damage caused by batteries used in connection with the unit.
This warranty covers bench repairs only, and any repairs must be made at the shop or place designated in writing by Aiphone.
Aiphone will not be responsible for any costs incurred involving on site service calls.
http://www.aiphone.com/
- 8 -
Ambient temperature:
Asking for repairs:
Cleaning:
0˚C〜40˚C(＋32˚F〜＋104˚F).
In case the unit does not operate properly, ask qualified technician to repair it.
Clean the equipment with a soft cloth dampened with neutral household cleanser.
Never use any abrasive cleaner or cloth.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Increase the separation between the equipment and receiver. Consult the dealer or an experienced radio/TV technician for help.
TECHNICAL PRECAUTIONS
SPECIFICATIONS (GF-MK)
Max. 16 letters for names.
210 H x 215 W x 69 D (mm). 8-1/4" H x 8-1/2" W x 2-3/4" D.
Approximately 900g (1.98 lbs.)
LCD display:
Dimensions:
Unit weight:
Adjusting call tone volume; Setting switches;
DIP switches bank
(SW1)
GF-MK Back view
SW1
ON
14 3
2
HIGHLOW MID
Call tone volume control
Adjustment
Bottom expanded view
3: Remains unused.
2: Remains unused.
GF-MK
When you forgot your ID code
Turn the switch on for approx. 2 sec.
The ID code returns to initial 1111.
1
ON
4
For the second Security
Guard Station
Put the switch 4 to ON position.
ON
Note; After wiring, be sure to set for second GF-MK station, which must not
be rechanged. If forgotten, "CALL-ID#ERROR" message will be displayed.
In this case, put DIP SW4 to ON while GF-BC is turned off, and repower it.
GF-MK07.1.309:07AMページ8