AirLive AirDual-AC12 Installation and operation manual

Ver. 1.0
Web Manual
AirDual-AC12
Wi-Fi 5 AC 1200Mbps Outdoor CPE
(Patch antenna)
AWOD-12ACi
Wi-Fi 5 AC 1200Mbps Outdoor CPE
(Omni antenna)
AWOD-30AXi
Wi-Fi 6 AX 1800Mbps Outdoor CPE
(Omni antenna)

CONTENTS
Chapter
1
Product Introduction
1
1.1
Package Contents AirDual
-AC12 and AWOD-12ACi
1
1.2
Package Contents AWOD
-30ACi
1
1.3
Product Specification AirDual
-AC12
2
1.4
Product Specification AWOD
-12ACi
3
1.5
Product Specification AWOD
-30ACi
4
Chapter
2
Hardware Installation
5
2.1
AirDual
-AC12 and AWOD-12ACi Port description
5
2.2
AWOD
-30AXi Port description
6
2.3
AirDual
-AC12, AWOD-12ACi, AWOD-30AXi Hardware installation
7
Chapter
3
Quick Installation Guide
8
3.1
AirDual
-AC12, AWOD-12ACi, AWOD-30AXi , Web login Management
8
3.2
Configuring the IP Address Manually
8
3.3
Starting Setup in the Web UI
9
Chapter
4
Configure the CPE
10
4.1
Main Home Page
10
4.2
Wizard Configuration
11
4.3
Gateway Mode (Router) Wizard
12
4.3.1
WAN Settings Static IP Wizard
13
4.3.2
WAN Settings PPPoE Wizard
14
4.3.3
WAN Settings DHCP Wizard
15
4.3.4
Wi
-Fi Settings Wizard
15
4.4
AP Mode Wizard
18
4.4.1
Wi
-Fi Settings Wizard
19
4.5
Repeater Mode
21
4.5.1
Wi
-Fi Settings Wizard
22
4.5.2
LAN Settings Wizard
23
4.6
Wi
-Fi
25
4.6.1
VAP
26
4.6.2
Wi
-Fi Analyzer
27
4.6.3
MAC ACL
28
4.6.4
Wi
-Fi Timer
29
4.6.5
Repeater
29
4.6.6
Advanced
30

Chapter
4.7
Network (AP Mode)
31
4.7.1
LAN Settings
31
4.7.2
Cloud
32
4.8
Network (Gateway Mode)
32
4.8.1
LAN Settings
32
4.8.2
Static DHCP
33
4.8.3
WAN
34
4.8.4
WAN DHCP
34
4.8.5
WAN Advanced Settings
35
4.8.6
WAN Static IP
36
4.8.7
WAN PPPoE
37
4.8.8
Cloud
38
4.9
Firewall (Gateway Mode Only)
39
4.9.1
URL Filter
39
4.9.2
IP Filter
40
4.9.3
MAC Filter
42
4.9.4
Port Mapping
43
4.9.5
DMZ
45
4.10
Manage
46
4.10.1
Configure
46
4.10.2
Timed Reboot
47
4.10.3
Upgrade
48
4.10.4
Time Manager
49
4.10.5
Log
50
4.10.6
QoS (Gateway Mode only)
51
4.10.7
IP Group (Gateway Mode only)
53
4.10.8
Time Group (Gateway Mode only)
54
4.10.9
DDNS (Gateway Mode only)
55
Chapter
5
FIT Mode
56

Userguide for AirDual-AC12, AWOD-12ACi, AWOD-30AXi
1.1
Package Contents ofWDAP-C7210E
Package Contents ofWDAP-W1200E
Chapter 1. Product Introduction
PackageContents AirDual-AC12 and AWOD-12ACi
Before using this CPE, please check if there is anything missing in the package, and contact your dealer of purchase to
claim for missing items:
⚫AirDual-AC12 or AWOD-12ACi CPE
⚫1x UTP Cable
⚫1x Power Cable
⚫1x PoE Injector
⚫1x Clamp Hoop
⚫InstallationGuide
1.2 PackageContents AWOD-30ACi
Before using this CPE, please check if there is anything missing in the package, and contact your dealer of purchase to
claim for missing items:
⚫AWOD-30AXi CPE
⚫2x Clamp Hoop
⚫InstallationGuide
-1-

-2-
Userguide for AirDual-AC12, AWOD-12ACi, AWOD-30AXi
1.3 Product Specification AirDual-AC12
Model AirDual-AC12
Device Interface
•Main Chip: Qualcomm QCA9563
•Flash:16MB
•RAM:128MB
•Standard: IEEE802.11ac, IEEE802.3, IEEE 802.11n,
IEEE 802.11a ,802.11b, 802.3at, 802.3az
•Frequency: 5.020GHz-6.100GHz/2.312GHz to
2.4835GHz
•Channel:CH36 ~CH165/CH1-13
(Country depended)
•Modulation: OFDM = BPSK, QPSK,16-QAM,64-
QAM; DSSS = DBPSK, DQPSK, CCK
•Data Rate: 1200Mbps (2.4Ghz 300Mbps, 5.8Ghz
900Mbps)
•RF Output Power: ≤ 22+2dBm (500mW)
•Antenna: 2.4GHz: 12dBi Panel Antenna\5GHz:
14dBi Panel Antenna
•WAN: 1 * 10/100/1000Mbps RJ-45 WAN Port,
support IEEE 802.3af 48V PoE in
•LAN: 1 * 10/100/1000Mbps RJ-45 LAN Port
•Reset Button:1 * Reset Button, Press 10 seconds,
the device will revert to factory default settings.
•LED Light: SYS, Wi-Fi, WAN, LAN, Signal Strength
•Power Consumption: <30W
•Water-proof Level: IP65
Firmware Function
Control
•Operation Mode: Wireless AP, Gateway, WiFi
Repeater
•Dynamic IP/Static IP/PPPoE/L2TP(Dual Access)
/PPTP(Dual Access)
Wireless
•SSID broadcast, SSID hide
•Multiple SSID up to 8
•Firewall: DoS, SPI Firewall, IP, MAC, URL filter, IP
and MAC Address Binding
•WiFi timed on/off
•Multicast acceleration
•VPN pass through
•DDNS, Port Forwarding, DMZ Host
•Security: OPEN, WPA, WPA2, WPA-PSK, WPA2-PSK,
802.1x encryption
•Support RF power adjustable based on
environment
•Max Users: 128
Network Function
•Tag VLAN setting based on SSID
•DHCP server
Device Management
•Backup the configuration information
•Restore the configuration information
•Reset to factory default settings
•Device reboot: reboot immediately or timed reboot
•Firmware upgrade
•Time management: including system time and time
synchronization
•System log
•Support WEB GUI management
•Support Cloud remote management (AP Mode)
Multiple Language
•English
ESD Protection
•ESD: Air discharge: ± 8KV, Contact discharge: ± 4KV
Environment
•Operating temperature: -30°C ~ +55°C
•Storage Temperature: -40°C ~ +70°C
•Operating Humidity: 10% ~ 90% (non-condensing)
•Storage Humidity: 5% ~ 90% (non-condensing)
•Enclosure: IP65
Standard package of switch
•Product size:
31.5cm x 14.5cm x 8cm (L*W*H)
•Package size:
TBD cm(L*W*H)
•Package content: TBD
1 x AirDual-AC12, PoE Injector, Install Accessory,
LAN Cable, User Manual
Ordering information
•AirLive AirDual-AC12
Wi-Fi AC1200 Gigabit Outdoor CPE

-3-
Userguide for AirDual-AC12, AWOD-12ACi, AWOD-30AXi
1.4 Product Specification AWOD-12ACi
Model AWOD-12ACi
Device Interface
•Main Chip: Qualcomm QCA9563
•Flash:16MB
•RAM:128MB
•Standard: IEEE802.11ac, IEEE802.3, IEEE 802.11n,
IEEE 802.11a ,802.11b, 802.3at, 802.3az
•Frequency: 5.150GHz-5.850GHz/2.312GHz to
2.4835GHz
•Channel: CH36 ~CH165/CH1-13
(Country depended)
•Modulation: OFDM = BPSK, QPSK,16-QAM,64-
QAM; DSSS = DBPSK, DQPSK, CCK
•Data Rate: 1200Mbps (2.4Ghz 300Mbps, 5.8Ghz
900Mbps)
•RF Output Power: ≤ 22+2dBm (500mW)
•Antenna: 5dBi Omni Antenna
•WAN: 1 * 10/100/1000Mbps RJ-45 WAN Port,
support IEEE 802.3af 48V PoE in
•LAN: 1 * 10/100/1000Mbps RJ-45 LAN Port
•Reset Button: 1 * Reset Button, Press 10 seconds,
the device will revert to factory default settings.
•LED Light: SYS, Wi-Fi, WAN, LAN, Signal Strength
•Power Consumption: <30W
•Water-proof Level: IP65
Firmware Function
Control
•Operation Mode: Wireless AP, Gateway, WiFi
Repeater
•Dynamic IP/Static IP/PPPoE/L2TP(Dual Access)
/PPTP(Dual Access)
Wireless
•SSID broadcast, SSID hide
•Multiple SSID up to 8
•Firewall: DoS, SPI Firewall, IP, MAC, URL filter, IP
and MAC Address Binding
•WiFi timed on/off
•Multicast acceleration
•VPN pass through
•DDNS, Port Forwarding, DMZ Host
•Security: OPEN, WPA, WPA2, WPA-PSK, WPA2-PSK
•Support RF power adjustable based on
environment
•Max Users: 128
Network Function
•Tag VLAN setting based on SSID
•DHCP server
Device Management
•Backup the configuration information
•Restore the configuration information
•Reset to factory default settings
•Device reboot: reboot immediately or timed reboot
•Firmware upgrade
•Time management: including system time and time
synchronization
•System log
•Support WEB GUI management
•Support Cloud remote management (AP Mode)
Multiple Language
•English
ESD Protection
•ESD: Air discharge: ± 8KV, Contact discharge: ± 4KV
Environment
•Operating temperature: -30°C ~ +55°C
•Storage Temperature: -40°C ~ +70°C
•Storage Humidity: 5% ~ 90% (non-condensing)
•Enclosure: IP65
Standard package of switch
•Product size:
31.5cm x 14.5cm x 8cm (L*W*H)
•Package size:
TBD cm(L*W*H)
•Package content: TBD
1 x AWOD-12ACi, PoE Injector, Install Accessory,
LAN Cable, User Manual
Ordering information
•AirLive AWOD-12ACi
Wi-Fi AC1200 Gigabit Outdoor AP

-4-
Userguide for AirDual-AC12, AWOD-12ACi, AWOD-30AXi
1.5 Product Specification AWOD-30AXi
Model AWOD-30AXi
Device Interface
•Main Chip: Qualcomm IPQ5018
•Flash: NOR 8MB + NAND 128MB
•RAM:512MB
•Standard: IEEE802.11ax, IEEE802.11ac, IEEE802.3,
IEEE 802.11n, IEEE 802.11a ,802.11b, 802.3at,
802.3az
•Frequency: 5.150GHz-5850GHz/2.4GHz to
2.484GHz
•Channel: CH36 ~CH165/CH1-13
(Country depended)
•Modulation: DL/UL-OFDMA modulation, Seamless
Roaming
•Data Rate: 3000Mbps (2.4Ghz 600Mbps, 5.8Ghz
2400Mbps)
•RF Output Power: ≤ 27+2dBm (500mW)
•Antenna: 8dBi Omni Antenna
•WAN: 1 * 10/100/1000Mbps RJ-45 WAN Port,
support IEEE 802.3af 48V PoE in
•LAN Console: 1 * 10/100/1000Mbps RJ-45
Console Port
•Reset Button: 1 * Reset Button, Press 10 seconds,
the device will revert to factory default settings.
•LED Light: SYS, WAN, 2.4G, 5.8G
•Power Consumption: <24W
•Water-proof Level: IP67
Firmware Function
Control
•Operation Mode: Wireless AP, Gateway, WiFi Repeater
•Dynamic IP/Static IP/PPPoE/L2TP(Dual Access)
/PPTP(Dual Access)
Wireless
•SSID broadcast, SSID hide
•Multiple SSID up to 8
•Firewall: DoS, SPI Firewall, IP, MAC, URL filter, IP
and MAC Address Binding
•WiFi timed on/off
•Multicast acceleration
•VPN pass through
•DDNS, Port Forwarding, DMZ Host
•Security: OPEN, WPA, WPA2, WPA-PSK, WPA2-PSK,
WPA3
•Support RF power adjustable based on
environment
•Max Users: 160
Network Function
•Tag VLAN setting based on SSID
•DHCP server
Device Management
•Backup the configuration information
•Restore the configuration information
•Reset to factory default settings
•Device reboot: reboot immediately or timed reboot
•Firmware upgrade
•Time management: including system time and time
synchronization
•System log
•Support WEB GUI management
•Support Cloud remote management (AP Mode)
Multiple Language
•English
ESD Protection
•ESD: Air discharge: ± 8KV, Contact discharge: ± 4KV
Environment
•Operating temperature: -30°C ~ +70°C
•Storage Temperature: -40°C ~ +70°C
•Storage Humidity: 5% ~ 95% (non-condensing)
•Enclosure: IP67
Standard package of switch
•Product size:
30.3cm x 18cm x 8.7cm (L*W*H)
•Package size:
TBD cm(L*W*H)
•Package content: TBD
1 x AWOD-30AXi, PoE Injector, Install Accessory,
LAN Cable, User Manual
Ordering information
•AirLive AWOD-30AXi
Wi-Fi 6 AX3000 Gigabit Outdoor AP

-5-
Userguide for AirDual-AC12, AWOD-12ACi, AWOD-30AXi
Chapter 2. Hardware Installation
2.1 AirDual-AC12 and AWOD-12ACi Port description.
LED Status Function
2G
On
(Green)2.4G is On
5G
On
(Green)5G is On
SYS
On (
Green) Outdoor CPE is ON and working
2G, 5G, SYS LED
LED Description.
Port Description.
Port Description
12V DC
12V
DC port for the power adapter( DC-Jack 5.5 x 2.1mm )
LAN/WAN LED
The
LAN/WAN port is connected
WAN/PoE
LAN
port with Power over Ethernet (PoE) IN (802.3at/af)
LAN
LAN
port connecting to the network equipment.
Reset
To
restore to the factory default setting, press and hold the Reset Button for
about 15 seconds, and
then release it.
Back Panel
DC LAN LED WAN LED WAN/PoE Port LAN Port Reset
Front

-6-
Userguide for AirDual-AC12, AWOD-12ACi, AWOD-30AXi
2.2 AWOD-30AXi Port description.
Front Panel
LED Description.
LED State Function
PWR
On
Power
On
Off
Power
Off
SYS
On/Flash
SYS working
Off
Device off
WAN
On/Flash
WAN
connected / data transmitting
Off
WAN
disconnected
2.4G
On
2.4G On
Off
2.4G Off
5G
On
5G On
Off
5G Off
Port Description.
Port Description
WAN/LAN/PoE
WAN/
LAN port with Power over Ethernet (PoE) IN (802.3at/af)
Console Port
LAN
Console port
Reset
T
o restore the factory default setting, press and hold the Reset Button for
about 1
0 secs, and then release it. Located just above the RJ45 connector of WAN Port
Bottom Panel

-7-
Userguide for AirDual-AC12, AWOD-12ACi, AWOD-30AXi
2.3 AirDual-AC12, AWOD-12ACi, AWOD-30AXi Installation.
For the Outdoor CPE, they will be installed on a Pole or Wall based on the following steps:
Take the Clamp Hoop from the retail box and open it. Pull it though the back bracket of the Outdoor CPE and fix it the
pole. Make sure the CPE is facing the correct location and is mounted securely so it cannot move. When mounting on a
flat surface (like a wall) please use two screws or bolts (not provided) and mount them up with the screw fixture holes
in the back of the CPE bracket. Do not for get the connected to PoE LAN cable to power on the CPE.
Clamp Hoop

This chapter will show you how to configure the basic functions of your AP within minutes.
-8-
Userguide for AirDual-AC12, AWOD-12ACi, AWOD-30AXi
Chapter 3. Quick Installation Guide
3.1 AirDual-AC12, AWOD-12ACi, AWOD-30AXi, Web login Management.
Now click OK to save your settings.
Manual Network Setup –TCP/IP Configuration.
The default IP address of the CPE is 192.168.188.253, and the default subnet is 255.255.255.0. These values can be
changed as you want. For this guide we will use the default values to introduce the webui.
Connect the CPE with your PC by plugging one end of an Ethernet cable in the LAN port of the CPE or into a free port
on the PoE switch to which the CPE is also connected and the other end in the LAN port of PC. When the CPE powered
by a PoE switch, you can connect to the CPE by connecting direct to LAN port of the CPE or by connecting to the same
PoE switch. You can also use the supplied PoE Injector (AirDual-AC12 and AWOD-12ACi only) to power CPE when not
using a PoE switch.
In the following sections, we’ll introduce how to install and configure the TCP/IP correctly in Windows. And the
procedures in other operating systems are similar. First, make sure your Ethernet Adapter is working, and refer to the
Ethernet adapter manual if needed.
3.2 Configuring the IP Address Manually.
Using the LAN connection, you need to set the IP address of the TCP/IP property of the network card to
192.168.188.X (X is number of 2--252) first, so that the device and PC in the same IP segment, and set the subnet
mask to 255.255.255.0, as shown in the following picture:

-9-
Userguide for AirDual-AC12, AWOD-12ACi, AWOD-30AXi
3.3 Starting Setup in the Web UI.
It is easy to configure and manage the CPE with a web browser.
Input 192.168.188.253 into the browser, and the login page will appear, the default login password is: admin.
When the CPE was connected to a PoE switch which also transfers IP address from a router connected to it. It could
be that the IP Address of the CPE has changed to an IP address in your local range.
***Note***
The Webui images used in this guide differ from the actual Webui of the CPE used.
Some function shown in the Webui images in this guide could not be available / shown on your device.
To change the language settings from English to Spanish click on the “˅" to open the menu. (Only for indoor Ceiling
and inWall AP model).
The color and layout between the different models of CPEs can slightly different, but the operation is the same.

The page includes the following fields:
-10-
Userguide for AirDual-AC12, AWOD-12ACi, AWOD-30AXi
Chapter 4. Configure the CPE
4.1 Main Home Page.
The below web GUI and the topology used in this guide uses the inWall-U618AX/AirDual-AC12 as an example.
It is easy to configure and manage the AP with the web browser. The default setting of the CPE is AP Mode.
The default setting for operation is FAT mode, to view the FIT mode please see chapter 5.
Object
Description
Mode
Shows the current mode status, AP or Gateway mode.
Fat AP/ Fit AP
Switch between Fat AP and Fit AP mode. (Fit mode is used with WLAN
-64/128GM
controller). The Fat and Fit mode is only available in AP Mode not Gateway Mode.
Device Info
Shows the CPU and Memory usage.
Device Description
You can enter the device description.
Flow (2.4/5G Wi-Fi) bps
Shows the Upstream/Downstream graph, select either 2.4G or 5Ghz
LAN Info
Shows the device IP mode, LAN IP, Subnet, Gateway and MAC address.
Wi-Fi Information
It shows the Wi
-Fi status, SSID, Channel, Encryption, MAC address
Hardware accelerate
Only in Gateway Mode.
Version
Shows the current device firmware version.
Reboot and Password Change:
Click on the Green icon with the 4 squares in the top right corner and a pulldown menu will appear.
To change the Password, click on the lock icon and enter your new Password.
To Reboot the CPE, click on the orange icon

-11-
Userguide for AirDual-AC12, AWOD-12ACi, AWOD-30AXi
4.2 Wizard Configuration.
Wizard: It instruct users to configure wireless AP’s operation mode based on needs, there are three operation modes
including AP, Gateway and Repeater Mode. Please confirm the operation mode first before starting the configuration.
The default settings of the CPE is AP mode.
Clicking on Wizard the status page will pop up, for each operation mode there is an explanation for better application.
AP Mode:
In this mode, the AP wireless interface and cable interface are bridging together. Without NAT, firewall and all
network related functions.
Gateway Mode:
In this mode, the device is supposed to connect to internet via ADSL/Cable Modem. The NAT is enabled, and PCs in the
LAN ports share the same IP to ISP through WAN port. The connection type can be setup in WAN page by using PPPoE,
DHCP client or static IP.
In Gateway mode an additional Firewall menu will also appear. This menu is not visible in AP and Repeater mode.
Repeater Mode:
In this mode, the user can access wireless AP, Devices can be connected to other wireless networks using wireless, all
interfaces are bridged together. White NAT, firewall and all related functions.

-12-
Userguide for AirDual-AC12, AWOD-12ACi, AWOD-30AXi
4.3 Gateway Mode (Router).
Before changing the default AP mode to the Gateway mode, confirm your internet will be Static IP, PPPoE, or DHCP.
Then click on the Gateway mode and the below image will pop-up. Please choose the right WAN settings mode, then
click next to continue. Then configure the wireless parameters and click next.
Clicking next will complete the Gateway mode setting and show following picture:
Please Note: The CPE will restart for the changes to take effect.

The page includes the following fields:
Object
Description
IPAddress
Enter the WAN
IP address provided by your ISP. Enquire your ISP if you
are
not clear
Subnet Mask
Enter
WAN Subnet Mask provided by your ISP
Default Gateway
Enter the
WAN Gateway address provided by your ISP
Primary DNS
Enter the necessary
DNS address provided by your ISP
Second DNS
Enter the second
DNS address provided by your ISP
-13-
Userguide for AirDual-AC12, AWOD-12ACi, AWOD-30AXi
4.3.1WAN Settings.
Static IP
If your ISP offers you a static IP Internet connection type, select “Static IP" and then enter IP address, subnet mask,
default gateway and primary DNS information provided by your ISP in the corresponding fields.

The page includes the following fields:
Object
Description
Username
Enter the PPPoE
Username provided by yourISP
Password
Enter the PPPoE
Password provided by your ISP
Server Name
No Need, Don’t fill
Service Name
No Need, Don’t fill
-14-
Userguide for AirDual-AC12, AWOD-12ACi, AWOD-30AXi
4.3.2WAN Settings.
PPPoE (ADSL)
Select PPPOE if your ISP is using a PPPoE connection and provided you wit an PPPoE username and password.

-15-
Userguide for AirDual-AC12, AWOD-12ACi, AWOD-30AXi
4.3.3WAN Settings.
DHCP
Choose “DHCP” and the router will automatically obtain IP addresses, subnet masks and gateway addresses from
your ISP.
4.3.4Wi-Fi Settings.
In the Wi-Fi settings the settings for the 2.4Ghz are first after these are done click next to setup the 5Ghz Wi-Fi
settings.
Setup your own SSID, Wireless Mode, Channel, Encryption and Wi-Fi Password.

The page includes the following fields:
Object
Description
Wi-Fi Status Select ON (Green) or OFF (Gray) to enable or disable Wireless LAN
SSID This is the wireless network name. The default SSID is Wireless
2.4G_XXXXXX and Wireless 5.8G_XXXXXX. X is the last 6 numbers of the AP
MAC address.
Hide your SSID Select ON (Green) or OFF (Gray) to hide wireless LAN or not
Wireless Mode Select the Wireless mode and Channel bandwidth, “20MHz” or “40MHz”
or
“80MHz”, The “160Mhz” is only for the AX 3000Mbps model.
Channel Select the operating channel you would like to use. The channel range will
be changed by selecting a different domain.
Encryption Select the wireless encryption.
Timed Reboot Set the after how many days the AP should automatically restart.
-16-
Userguide for AirDual-AC12, AWOD-12ACi, AWOD-30AXi

-17-
Userguide for AirDual-AC12, AWOD-12ACi, AWOD-30AXi
Router Mode:
After the CPE has restarted the Gateway mode will be active.
The web GUI will now display the Gateway Mode and will have an additional Firewall menu on the left side.
See Chapter 4.8 for information.