Airspan AIRSTRAND 2200 User manual

© Copyright by Airspan Networks Ltd., 2021. All rights reserved worldwide.
AIRSTRAND 2200 INSTALLATION GUIDE
AirStrand 2200
Installation Guide
Document Part Number: DUG01287
Document Revision: A2
Published: October 2021

AirStrand 2200 Installation Guide
AirStrand 2200 –Installation Guide
© Copyright Airspan Networks Ltd., 2021 P/N: DUG01287 Rev. A2, Oct 2021
i
© Copyright by Airspan Networks Ltd., 2021. All rights reserved worldwide.
Legal Notices
The information contained within this document is proprietary, privileged and intended only for the recipient. As such, the
information is subject to all relevant copyright, patent and other laws protecting intellectual property, as well as any
specific agreements protecting Airspan Networks Ltd. rights in the aforesaid information. Neither this document nor the
information contained herein may be published, reproduced, transmitted or disclosed to third parties, in whole or in part,
without the express, prior, written permission of Airspan Networks Ltd. In addition, any use of this document or the
information contained herein for the purposes other than those for which it is disclosed is strictly forbidden.
Airspan Networks Ltd. reserves the right, without prior notice or liability, to make changes in equipment design or
specifications.
Information supplied by Airspan Networks Ltd. is believed in good faith to be accurate and reliable, while every care has
been taken in preparing these documents. However, Airspan Networks Ltd. does not make any representations and gives
no warranties of whatever nature in respect of these documents, including without limitation, the accuracy or
completeness of any information, facts and/or opinions contained therein. No responsibility is assumed by Airspan
Networks Ltd. for the use of the documents nor for the rights of third parties which may be effected in any way by the use
thereof. The provision of these documents (and the documents themselves) does not constitute professional advice of any
kind. Any representation(s) in these documents concerning performance of Airspan Networks Ltd. product(s) are for
informational purposes only and are not warranties of future performance, either expressed or implied. Airspan Networks
Ltd., its affiliates, directors, employees and agents shall not be held liable for any damages or losses, of any nature
whatsoever, arising from any use of and/or reliance on the documents.
These documents may contain flaws, omissions or typesetting errors; no warranty is granted nor liability assumed in
relation thereto unless specifically undertaken in Airspan Networks Ltd. sales contract or order confirmation. Information
contained herein is periodically updated and changes will be incorporated into subsequent editions. If you have
encountered an error, please notify Airspan Networks Ltd.
Product performance figures quoted within this document are indicative and for information purposes only.

AirStrand 2200 Installation Guide
AirStrand 2200 –Installation Guide
© Copyright Airspan Networks Ltd., 2021 P/N: DUG01287 Rev. A2, Oct 2021
ii
TABLE OF CONTENTS
Document Information................................................................................................................ 1
Revision History ............................................................................................................................1
Warnings and Cautions ............................................................................................................... 2
Human Exposure to Radio Frequencies ......................................................................................2
Radio Interference........................................................................................................................2
Modifications................................................................................................................................2
General..........................................................................................................................................2
Important Safety Instructions ...............................................................................................2
Safety…..........................................................................................................................................3
Warning of Hazardous Voltages ..................................................................................................3
Adherence to European Directive 2014/53/EU..........................................................................3
Warning Symbols..........................................................................................................................4
Service Information ......................................................................................................................4
UL Information..............................................................................................................................4
Lightning Protection.....................................................................................................................4
DECLARATION OF CONFORMITY..................................................................................................6
GPS Compliance............................................................................................................................8
Maximum Output TX Total Power ...............................................................................................9
Power Consumption.....................................................................................................................9
Antenna Solution..........................................................................................................................9
About This Document................................................................................................................ 10
Purpose .......................................................................................................................................10
Intended Audience .....................................................................................................................10
Document Conventions..............................................................................................................10
Related Reading..........................................................................................................................11
1Introduction................................................................................................................... 12
1.1 AirStrand 2200 ..............................................................................................................12
2Getting Started.............................................................................................................. 13
2.1 AirStrand 2200 Installation Checklist...........................................................................13
3Verifying Prerequisites.................................................................................................. 14
3.1 Verifying Site Requirements.........................................................................................14
3.2 Verify Installation Requirements..................................................................................14
4Installing AirStrand 2200 .............................................................................................. 18
4.1 Strand Mounting the AirStrand 2200 ..........................................................................18
4.2 Antenna Sectors............................................................................................................21
5Connecting and Managing Cables................................................................................ 22
5.1 Removal of Connection Panel Cover............................................................................22
5.2 Grounding......................................................................................................................23
5.3 Interface Connection....................................................................................................23
Job Sheet........................................................................................................... 25

AirStrand 2200 Installation Guide
AirStrand 2200 –Installation Guide
© Copyright Airspan Networks Ltd., 2021 P/N: DUG01287 Rev. A2, Oct 2021
iii
Acronyms, Abbreviations, and Definitions............................................................................... 26
Customer Service Help Desk ..................................................................................................... 27
Airspan Encourages Comments................................................................................................ 27

AirStrand 2200 Installation Guide
AirStrand 2200 –Installation Guide
© Copyright Airspan Networks Ltd., 2021 P/N: DUG01287 Rev. A2, Oct 2021
iv
FIGURES
Figure 1: AirStrand 2200............................................................................................................................. 12
Figure 2: AirStrand 2200 Dimensions ........................................................................................................ 16
Figure 3: Assemble Strand Hangers on Unit.............................................................................................. 19
Figure 4: Hanger and Clamp Assembly...................................................................................................... 19
Figure 5: AirStrand 2200 0n Cable Strand ................................................................................................. 20
Figure 6: GPS Bracket Adjustment............................................................................................................. 20
Figure 7: AirStrand Sectors......................................................................................................................... 21
Figure 8: Connection Panel Cover Removed............................................................................................. 22
Figure 9: Ground Screw Connection.......................................................................................................... 23
Figure 10: Use 2 Wrenches to Loosen....................................................................................................... 24
TABLES
Table 1: AirStrand 2200 Maximum Output TX Total Power ........................................................................9
Table 2: Antenna............................................................................................................................................9
Table 3: Typographic Conventions............................................................................................................. 10
Table 4. Minimum Hardware Requirements............................................................................................. 14
Table 5. Parts & Kits.................................................................................................................................... 15
Table 6: AirStrand 2200 Physical Dimensions ........................................................................................... 16
Table 7: AirStrand 2200 Operational Tolerances...................................................................................... 17
Table 8: System LED Function .................................................................................................................... 24
Table 9: Job Sheet....................................................................................................................................... 25
Table 10: Acronyms, Abbreviations, and Definitions................................................................................ 26

AirStrand 2200 Installation Guide
AirStrand 2200 –Installation Guide
© Copyright Airspan Networks Ltd., 2021 P/N: DUG01287 Rev. A2, Oct 2021
1
Document Information
This document details procedures for installing the Airspan’s Air5G AirStrand 2200, as part of the 5G
NR standard and its place in the Airspan product suite. This document is intended for qualified
personnel with a working knowledge of 5G.
Revision History
Revision
Date
Summary of Changes
Created by
Rev 0.1
July 2021
Initial document - draft
MSF
Rev 0.2 - 0.3
July 2021
Changes from comments
MSF
Rev 0.4 + 0.5
August 2021
Added - LED explanation, Antenna Sectors, comments
MSF
Rev A
August 2021
Published
MSF
Rev A1
August 2021
Minor terminology correction
CY
Rev A2
October 2021
Added Grounding requirement
CY / MSF

AirStrand 2200 Installation Guide
AirStrand 2200 –Installation Guide
© Copyright Airspan Networks Ltd., 2021 P/N: DUG01287 Rev. A2, Oct 2021
2
Warnings and Cautions
Human Exposure to Radio Frequencies
The AirStrand 2200 should be operated from a minimum safe distance of 49cm. (19.4 in.).
Radio Interference
The AirStrand 2200 generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment on and off, the technician is encouraged to try to correct the
interference by performing one or more of the following measures:
Re-orientate or relocate the unit
Increase separation between the units and/or End Devices
Connect the equipment to a circuit different from that to which the power source is connected
Modifications
Any changes and modifications to this device that are not expressly approved by Airspan Networks
may void the user's authority to operate the equipment.
General
Only qualified personnel should be allowed to install, replace, and service the equipment.
The device cannot be sold retail, to the general public or by mail order. It must be sold to
operators.
Installation must be controlled.
Installation must be performed by licensed professionals.
Installation requires special training. The AirStrand 2200 should be installed ONLY by
experienced installation professionals who are familiar with local building and safety codes and,
wherever applicable, are licensed by the appropriate government regulatory authorities. Failure
to do so may void Airspan's product warranty and may expose the end user or the service
provider to legal and financial liabilities. Airspan and its resellers or distributors are not liable for
injury, damage or violation of regulations associated with the installation of outdoor units or
antennas.
The device is to be installed in a Restricted Access Location.
Important Safety Instructions
Read and Save these instructions
This Installation Guide contains instructions and warnings that should be followed during
installation, and operation.
Failure to follow these instructions could cause bodily injury and/or product failure

AirStrand 2200 Installation Guide
AirStrand 2200 –Installation Guide
© Copyright Airspan Networks Ltd., 2021 P/N: DUG01287 Rev. A2, Oct 2021
3
Safety
1. Read this guide and follow all operating and safety instructions.
2. Supply cord is not shipped with the unit and is to be provided by user. Installation is to be
performed by a qualified electrician according to local codes. Installation to be done in
accordance with the National Electrical Code (NEC), ANSI/NFPA 70, the Canadian Electrical
Code (CEC), Part I, CAN/CSA C22.1, and when applicable, the National Electrical Safety
Code, IEEE C2.
3. Static sensitive components inside - do not remove the lid or base: No user serviceable
parts inside.
4. The ground connection should be made before connecting to supply connections.
5. Position the power cord to avoid possible damage; do not overload circuits.
6. Do not place this product on or near a direct heat source, and avoid placing objects on the
terminal.
7. To avoid electrical shock do not install this device during adverse conditions such as rain or
inclement weather.
8. Use only a damp cloth for cleaning. Do not use liquid or aerosol cleaners. Disconnect the
power before cleaning.
9. The units should not be located too near power lines or other electrical power circuits,
where it can come into contact with such power lines or circuits.
10. The radio transceiver must be properly grounded to protect against power surges and
accumulated static electricity. It is the user’s responsibility to install this device in
accordance with the local electrical codes.
11. Installation of the AirStrand 2200 46must be contracted to a professional installer.
12. The circuit breaker should be easily accessible in case you have to disconnect the device.
13. When installed in the final configuration, the product must comply with the applicable
Safety Standards and regulatory requirements of the country in which it is installed. If
necessary, consult with the appropriate regulatory agencies and inspection authorities to
ensure compliance.
Warning of Hazardous Voltages
On AC installations, hazardous voltages exist. Use caution when verifying or working with AC power.
Remove metal jewelry that could come into contact with AC power.
On DC sections, short-circuiting the low voltage, low impedance circuits can cause severe arcing that
may result in burns or eye damage. Remove rings, watches etc. to avoid shorting DC circuits.

Airspan products do not contain hazardous substances (as defined in UK Control of
Substances Hazardous to Health Regulations 1989 and the Dangerous Substances
Regulations 1990). At the end of any Airspan products life cycle, the customer should
consult with Airspan to ensure that the product is disposed of in conformance with the
relevant regulatory requirements.
Adherence to European Directive 2014/53/EU
European Council Recommendation 2014/53/EU details basic restrictions and reference levels on
human exposure to electromagnetic fields as advised by the ICNIRP. Adherence to these
recommended restrictions and reference levels should provide a high level of protection as regards
the established health effects that may result from exposure to electromagnetic fields.

AirStrand 2200 Installation Guide
AirStrand 2200 –Installation Guide
© Copyright Airspan Networks Ltd., 2021 P/N: DUG01287 Rev. A2, Oct 2021
4
Warning Symbols
The following symbols may be encountered during installation or troubleshooting. These warning
symbols mean danger. Bodily injury may result if you are not aware of the safety hazards involved in
working with electrical equipment and radio transmitters. Familiarize yourself with standard safety
practices before continuing.
Caution, hot surface
Caution
Electro-Magnetic
Radiation
High Voltage
DC
Service Information
Refer all repairs to qualified service personnel. Do not modify any part of this device, as this will void
the warranty.
Disconnect the power to this product and return it for service if the following conditions apply:
1. The terminal does not function after following the operating instructions outlined in this
manual.
2. The product has been dropped or the housing is damaged.
Locate the serial number of the terminal and record this on your registration card for future
reference. Also record the MAC address, located on the product sticker.
UL Information
The equipment must be properly grounded according with NEC and other local safety code
requirements.
Reminder to all the BWA system installers: Attention to Section 820-40 of the NEC which
provides guidelines for proper grounding and, in particular, specifies that the cable ground shall
be connected to the grounding system of the building, as close to the point of cable entry as is
practical.
AirStrand 2200 is designed to operate in environmental conditions complying with IP66 and
relevant standards.
Lightning Protection
WARNING: The following notes are general recommendations for the system.
The wireless equipment should be installed by a qualified professional installer and must follow local
and national codes for electrical grounding and safety. Failure to meet safety requirements and/or
use of non-standard practices and procedures could result in personal injury and damage to
equipment. A direct lightning strike may cause serious damage even if these guidelines are followed.
All outdoor wireless equipment is susceptible to lightning damage from a direct hit or induced
current from a near strike. Lightning protection and grounding practices in local and national
electrical codes serve to minimize equipment damage, service outages, and serious injury. Reasons
for lightning damage are summarized as:

AirStrand 2200 Installation Guide
AirStrand 2200 –Installation Guide
© Copyright Airspan Networks Ltd., 2021 P/N: DUG01287 Rev. A2, Oct 2021
5
- Poorly grounded tower/antenna sites that can conduct high lightning strike energy into equipment.
- Lack of properly installed lightning protection equipment that can cause equipment failures from
lightning induced currents.
A lighting protection system provides a means by which the energy may enter earth without passing
through and damaging parts of a structure. A lightning protection system does not prevent lightning
from striking; it provides a means for controlling it and preventing damage by providing a low
resistance path for the discharge of energy to travel safely to ground. Improperly grounded
connections are also a source of noise that can cause sensitive equipment to malfunction.
A good tower grounding system disperses most of the surge energy from a tower strike away from
the building and equipment.
To limit the equipment damage due to a lightning strike, the following practices are recommended
for the wireless system:
- Provide direct grounding from the antenna mounting bracket, the radio and antenna and the
lightning/surge protectors to the same ground point at the base of the tower or a ground bus on the
building. Use the grounding screws on the antenna bracket and the radio and antenna for
terminating the ground wires.
- The AC source ground must be connected to the same grounding system as the gNodeB.

AirStrand 2200 Installation Guide
AirStrand 2200 –Installation Guide
© Copyright Airspan Networks Ltd., 2021 P/N: DUG01287 Rev. A2, Oct 2021
6
DECLARATION OF CONFORMITY
Declaration of Conformity with Regard to the R&TTE Directive 2014/53/EU
Czech:
Airspan tímto prohlašuje, že tento přístroj je ve shodě se základními požadavky a dalšími příslušnými
ustanoveními směrnice 2014/53 / EU.
Danish:
Undertegnede, Airspan erklærer hermed, at følgende udstyrsenhed opfylder de væsentlige krav og
andre relevante krav i direktiv 2014/53 / EF.
Deutsch:
Hiermit erklärt Airspan, dass die Produkteinheit die grundlegenden Anforderungen und anderen
relevanten Bestimmungen der Richtlinie 2014/53 / EU erfüllt.
Estonian:
Käesolevaga kinnitab Airspan, et seadme seade vastab direktiivi 2014/53 / EL olulistele nõuetele ja
muudele kõnealuse direktiivi asjakohastele sätetele.
English:
This equipment is in compliance with the essential requirements and other relevant provisions of
Directive 2014/53/EU.
Español:
Por medio de este Airspan, declara que la unidad cumple con los requisitos esenciales y cualquier
otra disposición aplicable o exigible de la Directiva 2014/53 / UE.
Greek:
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ ΠΡΟΔΙΑΓΡΑΦΗ, η Airspan ΔΗΛΩΝΕΤΑΙ ότι η μονάδα συμμορφώνεται με τις
ουσιώδεις απαιτήσεις και τις λοιπές σχετικές διατάξεις της οδηγίας 2014/53 / ΕE.
Français:
Airspan déclare par la présente que l'appareil est conforme aux exigences essentielles et aux autres
dispositions pertinentes de la directive 2014/53 / UE.
Italiano:
Con la presente Airspan dichiara che questa unità è conforme ai requisiti essenziali e alle altre
disposizioni pertinenti stabilite dalla direttiva 2014/53 / UE.
Latvian:
Ar šo Airspan paziņo, ka vienība atbilst Direktīvas 2014/53 / ES būtiskajām prasībām un citiem
attiecīgajiem noteikumiem;
Lithuanian:
Šis „Airspan“ pareiškia, kad šis įrenginys atitinka esminius Direktyvos 2014/53 / ES reikalavimus ir
kitas nuostatas.
Nederlands:
Airspan verklaart hierbij dat de apparaateenheid voldoet aan de essentiële vereisten en andere
relevante bepalingen van richtlijn 2014/53 / EU.

AirStrand 2200 Installation Guide
AirStrand 2200 –Installation Guide
© Copyright Airspan Networks Ltd., 2021 P/N: DUG01287 Rev. A2, Oct 2021
7
Maltese:
Hawnhekk, Airspan, tiddikjara li din l-unità tikkonforma mar-rekwiżiti essenzjali u dispożizzjonijiet
rilevanti oħra li jinsabu fid-Direttiva 2014/53 / UE.
Hungarian:
Alulírott, az Airspan kijelenti, hogy az egység megfelel a 2014/53 / EU irányelv vonatkozó alapvető
követelményeinek és egyéb követelményeinek.
Polish:
Niniejszym Airspan oświadcza, że urządzenie jest zgodne z zasadniczymi wymaganiami i innymi
odpowiednimi postanowieniami dyrektywy 2014/53 / UE.
Português:
Airspan declara que esta unidade está em conformidade com os requisitos essenciais e outras
disposições da Diretiva 2014/53 / UE.
Slovenian:
Airspan izjavlja, da je ta enota skladna z bistvenimi zahtevami in drugimi ustreznimi določbami
Direktive 2014/53 / EU.
Slovak:
Airspan týmto vyhlasuje, že tento prístroj spĺňa základné požiadavky a všetky príslušné ustanovenia
Smernice 2014/53 / EÚ.
Suomalainen:
Airspan vakuuttaa täten, että laitteen tyyppi on direktiivin 2014/53 / EU olennaisten vaatimusten ja
muiden asiaankuuluvien säännösten mukainen.
Swedish:
Därmed intygar Airspan att denna enhet överensstämmer med de väsentliga egenskapskraven och
andra relevanta bestämmelser som anges i direktiv 2014/53 / EU.
Íslenska:
Airspan lýsir hér með yfir að þessi eining uppfylli grunnkröfur og aðrar kröfur tilskipunar 2014/53 /
ESB.
Norsk:
Airspan erklærer herved at utstyrsenheten oppfyller grunnleggende krav og andre relevante krav i
direktiv 2014/53 / EU.
Român:
Airspan declarăm pe propria răspundere că produsul produsului respectă cerințele esențiale și alte
prevederi aplicabile din Directiva 2014/53 / UE.
The Declaration of Conformity related to this product can be obtained from [email protected].

AirStrand 2200 Installation Guide
AirStrand 2200 –Installation Guide
© Copyright Airspan Networks Ltd., 2021 P/N: DUG01287 Rev. A2, Oct 2021
8
GPS Compliance
The GPS is in compliance with the essential requirements and other relevant provisions of Directive
2014/53/EU."
The GPS complies with the following EMC Common Regulatory Testing standards:
EN55022: Radiated and Conducted Emissions
CISPR 22: Class B
EN 50081-1: Generic Emissions Class B
EN 50082-1: Generic Immunity Class B
EN 61000-4-2: Electrostatic Discharge Immunity
EN 61000-4-3: Radiated RF EM Field Immunity Test
EN 61000-4-4: Electrical Fast Transient/Burst Test
EN 61000-4-6: Conducted Immunity
EN 61000-4-8: Magnetic Field Immunity

AirStrand 2200 Installation Guide
AirStrand 2200 –Installation Guide
© Copyright Airspan Networks Ltd., 2021 P/N: DUG01287 Rev. A2, Oct 2021
9
Maximum Output TX Total Power
Table 1: AirStrand 2200 Maximum Output TX Total Power
Product Code
Frequency Band
TX
Backhaul
AT22-N48-S
n48
(3550-3700MHz)
4x 1.25W
(4x31dBm)
DOCSIS3.1
!
Do not set maximum output TX power to higher than local regulations.
Power Consumption
AirStrand 2200 power consumption is <95W.
Antenna Solution
The AirStrand 2200 antenna architecture is based on a dual sector with dual 2x2 SBA antennas. The
two sectors support two carrier which can operate in same or in different frequencies. Each SBA
antenna supports two possible configurations: 90° and 180° (refers to -6dB), enabling adapting
antenna pattern to the specific deployment use case.
Table 2: Antenna
Per Sector
Single
Dual
Bandwidth / Gain
65° / 10.5dBi
150° / 8.5dBi
Max Total EIRP
44.5dBm
42.5dBm

AirStrand 2200 Installation Guide
AirStrand 2200 –Installation Guide
© Copyright Airspan Networks Ltd., 2021 P/N: DUG01287 Rev. A2, Oct 2021
10
Purpose
This guide provides the workflow and step-by-step procedures for installing the Airspan’s AirStrand
2200 variant. These procedures include:
Verify prerequisites
Assemble strand hangers on unit (if required)
Install the AirStrand 2200 on the strand cable
Connect and manage cables
Intended Audience
This guide is intended for persons who are responsible for installing the AirStrand 2200.
These persons should have a working knowledge of the equipment.
Document Conventions
This document uses the following typographic conventions.
Table 3: Typographic Conventions
Convention
Element
Blue underlined text
Cross-reference links.
Bold text
Keyboard buttons and GUI elements.
Command
Command names or phrases.
Computer output
Text displayed by the computer.
Hyperlinks
Website and e-mail addresses.
Danger
Signifies a hazardous situation—if not avoided—will cause death or
serious injury. Describes how to avoid it.
Warning
Signifies a hazardous situation—if not avoided—can cause death or
serious personal injury. Describes how to avoid it.
! Caution
Signifies a hazardous situation—if not avoided—can void the
product warranty, and cause property damage. Describes how to
avoid it.
Information/Note
Provides necessary information to explain a task.
Tip
Provides helpful hints.

AirStrand 2200 Installation Guide
AirStrand 2200 –Installation Guide
© Copyright Airspan Networks Ltd., 2021 P/N: DUG01287 Rev. A2, Oct 2021
11
Related Reading
The following documents contain related information:
AirStrand 2200 Product Specification
Airspan 5G Commissioning Manual (pending)

AirStrand 2200 Installation Guide
AirStrand 2200 –Installation Guide
© Copyright Airspan Networks Ltd., 2021 P/N: DUG01287 Rev. A2, Oct 2021
12
1Introduction
This section provides a descriptive overview of the Airspan’s AirStrand 2200 and its place in the
Airspan product suite.
This document is intended for readers with LTE/5G working knowledge.
All information in this document is for general information only, and is subject for change without
notice.
1.1 AirStrand 2200
AirStrand 2200 is part of Airspan’s gNB product family which enable operators to provide 5G
services.
The AirStrand 2200 supports two sectors of 5G NR and incorporates DOCSIS3.1 cable modem for
backhaul. The unit receives power and backhaul by the HFC coaxial plant (60V/90V AC).
AirStrand 2200 is a compact, easy to install gNB, designed for deployment at street-level, leveraging
its unique strand mount design. The product resembles a fiber splice box and doesn’t expose any
antenna.

For management please refer to the system Commissioning Manual.

AirStrand 2200 must be properly grounded (16AWG minimum) according with NEC and
other local safety code requirements.
Figure 1: AirStrand 2200

AirStrand 2200 Installation Guide
AirStrand 2200 –Installation Guide
© Copyright Airspan Networks Ltd., 2021 P/N: DUG01287 Rev. A2, Oct 2021
13
2Getting Started
2.1 AirStrand 2200 Installation Checklist
Plan the installation of the AirStrand 2200 by using the Installation Checklist, which you can find as a
removable job aid in Appendix A for this guide.

AirStrand 2200 Installation Guide
AirStrand 2200 –Installation Guide
© Copyright Airspan Networks Ltd., 2021 P/N: DUG01287 Rev. A2, Oct 2021
14
3Verifying Prerequisites
Prior to installing the AirStrand 2200, verify the required safety, power, tools, parts and components.
This chapter includes the hardware, software, and client requirements for installation.

Important: Set up requirements for the installation is detailed in the Job Sheet, see
Appendix_A.
3.1 Verifying Site Requirements
To set up the AirStrand 2200, an IP connection to a Network Management System (NMS) is required.
3.2 Verify Installation Requirements
3.2.1 Verify the Tools
Table 4. Minimum Hardware Requirements
Tool
Use
9/16 inch wrench
for securing the hanger 3/8-16 bracket nuts
Philips screwdriver
For adjusting GPS and for securing the Ground wire (if required)

AirStrand 2200 Installation Guide
AirStrand 2200 –Installation Guide
© Copyright Airspan Networks Ltd., 2021 P/N: DUG01287 Rev. A2, Oct 2021
15
3.2.2 Verify the Parts and Kits

Verify your order and requirements to ensure the correct unit type is being installed.
Table 5. Parts & Kits
Installation Kit /
Part
Part No.
Airspan No.
Consisting of:
Image
AirStrand 2200
unit + Mounting
Kit
AT22-N48-S
TBD
AirStrand 2200 5G
Sub6 eNG n48
(3550-3700MHz)
Hanger bracket x 2
with Clamps x 2
Hardware (bolts,
threaded stud and
nuts)
AirStrand 2200
Mounting Kit
(for replacement if
needed)
AT22-SMK-1
TBD
Hanger bracket x 2 with
Clamps x 2 Hardware
(bolts, threaded stud and
nuts)