Airwell PNV007 User manual

INSTALLATION MANUAL
MODELS
Wall-mounted type
PNV 007 PNV 015
PNV 009 PNV 018
PNV 012 PNV 021
SAFETY PRECAUTIONS
Part NO:468050156/02
● Readthefollowing"SAFETYPRECAUTIONS"carefullybeforeinstallation.
● Carryouttestrunningtoconrmthatnoabnormalityoccursaftertheinstallation.Then,explaintousertheoperation,careandmaintenanceas
statedininstructions.Pleaseremindthecustomertokeeptheoperatinginstructionsforfuturereference.
Thisindicationshowsthepossibilityofcausingdeathorseriousinjury.
WARNING
Thisindicationshowsthepossibilityofcausingharmordamagetheequipment.
CAUTION
WARNING
1)Usequaliedinstallerandfollowcarefullythisinstructions.Otherwiseitwillcauseelectricalshock,waterleakage,orestheticproblem.
2)Installatastrongandrmlocationwhichisabletowithstandtheset'sweight.Ifthestrengthisnotenoughorinstallationisnotproperlydone,theset
willdropandcauseinjury.
3)Forelectricalwork,followthelocalnationalwiringstandard,regulationandthisinstallationinstruction.Anindependentcircuitandsingleoutletmust
beused.Ifelectricalcircuitcapacityisnotenoughordefectfoundinelectricalwork,itwillcauseelectricalshockorre.
4)Usethespeciedcableandconnecttightlyforindoorconnection.Connecttightlyandclampthecablesothatnoexternalforcewillbeactedonthe
terminal.Ifconnectionorxingisnotperfect,itwillcauseheat-uporreattheconnection.
5)Wireroutingmustbeproperlyarrangedsothatcontrolboardcoverisxedproperly.Ifcontrolboardcoverisnotxedperfectly,itwillcauseheat-up
atconnectionpointofterminal,reorelectricalshock.
6)Whencarryingoutpipingconnection,takecarenottoletairsubstancesotherthanthespeciedrefrigerantgointorefrigerationcycle.Otherwise,it
willcauselowercapacity,abnormalhighpressureintherefrigerationcycle,explosionandinjury.
7)Donotdamageoruseunspeciedpowersupplycord.Otherwise,itwillcausereorelectricalshock.
8)Thisequipmentmustbeearthed.Itmaycauseelectricalshockifthegroundingisnotperfect.
9)Donotinstalltheunitatplacewhereleakageofammablegasmayoccur.Incasegasleaksandaccumulatesatsurroundingoftheunit,itmay
causere.
CAUTION
1)Selectionoftheinstallationlocation.
Selectainstallationlocationwhichisrigidandstrongenoughtosupportorholdtheunit,andselectalocationforeasymaintenance.
2)Donotreleaserefrigerant.
Donotreleaserefrigerantduringpipingworkforinstallation,reinstallationandduringrepairingarefrigerationparts.Takecareoftheliquidrefrigerant.
itmaycausefrostbite.
3)Itmayneedtwopeopletocarryouttheinstallationwork.
4)Donotinstallthisapplianceinalaundryroomorotherlocationwherewatermaydripfromtheceiling,etc.
5)Carryoutdrainagepipesasmentionedininstallationinstructions.Ifdrainageisnotperfect,watermayentertheroomanddamagethefurniture.
IM_PNV_1 A 1_GB

Required tools for Installation
NO. TOOI NO. TOOI.
1Screwdriver 7Knife
2Electricdrill,hole
coredrill(60mm) 8Measuringtape
3Hexagonalwrench
9Torquewrench
4Spanner
5Pipecutter
6Reamer
Attached accessories
No. Accessories part Qty.
1Mountingplate 1
2Airpurifyinglter(optional) 1
3Swrewswasherdowels 4
4Unitoperationmanual
Installationmanual 1
1SELECT THE BEST LOCATION
2HOW TO FIX INSTALLATION PLATE
 Thereshouldnotbeanyheatsourceorsteamneartheunit.
 Thereshouldnotbeanyobstaclesblockingtheaircirculation.
 Aplacewhereaircirculationintheroomisgood.
 Aplacewheredrainagecanbeeasilydone.
 Donotinstalltheunitnearthedoorway.
 Ensurethespacesindicatedbyarrowsfromthewall,ceiling,fenceorotherobstacles.(Fig1)
 Theapplianceshallbeinstalledover2.3mhigh.
Themountingwallisstrongandsolidenoughtopreventitfromthevibration.
Theedgeofinstallationcartonboardshouldbeatmorethan50mmatrightandleftofthewall.
 1.Locatethemountingplateonthewallinahorizontalposition.
 2.Markthepositionofthefourmountingholesonthewallanddrillfourholestoaccommodatethedowels.
 3.Mountthemountingplateonthewallbythefourscrews.Ensurescrewsaretightenedproperly.
 4.Markthelocationofthepipingholeoneithersideofthemountingplateasshown.
 5.Thepipingholeisdrilledata5down-wardangletopreventcondensedorrainwalerfrompenetratingbackintotheroom.
 6.Trimtheholeinthewallwitha70mmcommercialplastictube.
PNV 007
PNV 009
PNV 012
Fig1-1

50mm
min
50mm
min
PNV 015
PNV 018
PNV 021
3UNIT INSTALLATION
Unitoffersvedirectionsforinstallingrefrigerantpipe,pleaseinstallingtheunitaccordingtofollowinginstalltion:
1.Knockoutholeandpulloutthepipes. 4.Purifyinglterinstallation(optional).
2.Installtheunittowall. 5.Checkthedrainage.
3.Securetheunit.
Pull out the piping and hose
Install the Indoor Unit
 1.Hooktheindoorunitontotheupperportionof
installationplate(Engagetheindoorunitwiththe
upperedgeoftheinstallationplate).ensurethe
hooksareproperlyseatedontheinstallationplate
bymovinginleftandright.
 2.Usedtheinstallationsupportthatassembletothe
unithousingtosupporttheindoorunitinaangle
about25",thanconnectedthepipingandpower
supplycord.
Movethedrainhosenear
toarrowmarkandtapeit
withpipinginapositionas
mentionedinFig.below
Coverforthe
rightpiping
Coverforthe
bottompiping
Coverforthe
leftpiping
Drainhose Piping
Piping direction
Right
Rightrear
RightBottom
LeftRear Left
(Frontside)
Hooksat
installationplate
Piping
Drainhose
Fig1-2

Install the Indoor Unit(Continue)
Totakeouttheunit,pullthe
markingatthebottomunit,andpullit
slightlytowardsyoutodisengagethe
hooksfromtheunit.
Purifying lter installation (optional)
1.Openthegrille.
2.Removetheairfilters.
3.Putairpurifyingfilterintoplaceasshowninillustration.
Secure the Indoor Unit
1.Tapetheextraconnectingcableinabundleandkeepitbehindthe
chassis.Ensurethattheconnectingcableisnotclampedinbetween
theunit'shook(2positions)andinstallationplate.
2.Pressthelowerleftandrightsideoftheunitagainsttheinstallation
plateuntilhooksengageswiththeirslots(soundclick).
marking
Attentionnottobend
updrainhose
Rearview
Unit's
hook Installation
plate
Insulationofpipingconnections
●Carryoutinsulationafterchecking
forgasleaksandsecurewithvinyl
tape.
Vinyltape
Collaboratethepiping
communication
wiring
Drainhose Adjustthepipingslightlydownwards.
Airpurifyinglter
Airlter
1Bendthepipeas
closelyonthewallas
possible,butbecareful
thatitdoesn’tbreak.
2Donotwiringthe
powerwireand
communicationwire
together.

How to take out front grille
Pleasefollowthestepsbelowtotakeoutfrontgrilleifnecessaryduringservicing.
1.Settheverticalairflowdirectionlouvertothehorizontalposition.
2.SlidedownthetwocapsofPNV007/009/012onthefrontgrilleasshownin
theillustrationatright,thenremovethetwomountingscrews.(Iftheunitis
PNV015/018/021,ithasthreecaps).
3.Pullthelowersectionofthefrontgrilletowardsyourtoremovethefrontgrille.
Check the drainage
1Openfrontpanelandremoveairfilters.
(Drainagecheckingcanbecarriedoutwithoutremovingthefrontgrill).
2Pouraglassofwaterintothedraintray-styrofoam.
3Ensurethatwaterflowsoutfromdrainhoseoftheindoorunit.
Height Compensation Setting
TheCompensationsettingaccordingtoinstallationheightcanbedonebyusingthedipswitch11and12oncontrollerPCB.
InstallationHeight HeightCode DS11 DS12
2.3-2.7(m) H0 OFF OFF
2.7-3.1(m) H1 OFF ON
3.1-3.5(m) H2 ON OFF
>3.5(m) H3 ON ON
Note
1.Pleasedisconnecttheunitfrompowersupplywhenchangethesesettings.
2.Ifyoufeeltoonoisy,pleasesetDS11andDS12tolowerheightcodelevel.
Verticalairow
deectionlouver
(Movethevertical
vanetohorizontal)
Draintraystyrofoam
4ELECTRICAL WRING CONNECTION
Terminalblock(4P)
Powersupply
Terminalblock(2P)
Powersupplywiring
Tiethecommunicationwiringwithclamptightening
Fixthepowersupplywiringunderthecliptightening
Connect the drainage pipe
1UsestandardhardPVCpipe(19mm)forthedrainpipe.
2Usethedrainhosetochangethedirection.
3Insertthedrainhoseuntilitconnectsthedrainportverywell,andthensecureittightlywiththehoseclamp.
4Aftercheckingthedrainage,wrapthedrainhosewiththeinsulationandclamps.

Powersupplywiring
Tighteningtotorquefortheterminalscrews
Electricalcharacteristic
SpecicationsforeldsuppliedELBandwire
MainbusandR/Ccommunciationwiring
1.Unscrewandremovetheservicelid.
2.Connectthepowersupplywiringtothepowersupply
terminalblock.
3.Whendoingthis,pressthepowersupply wiringunderthe
wirecliptightly.
1.Usethecorrectscrewdriverfortighteningtheterminalscrews.Ifthebladeofscrewdriveristoosmall,theheadofthescrewmightbedamaged,andthe
screwwillnotbeproperlytightened.
2.Iftheterminalscrewsaretightenedtoohard,screwsmightbedamage.
3.Refertothetablebelowforthetighteningtorqueoftheterminalscrews.
1.Unscrewandremovetheservicelid.
2.ConnecttheR/Cwirings toR1,R2 terminal blockand the
mainbuswiringstoF1,F2terminalblock.
3.Pressthewiringsunderthewirecliptightly.
Terminal Size Tighteningtorque
Remotecontroller,Transmissionwiringandforcedoffterminalblock(4P) M3.5 0.8~1.0N.m
PowersupplyandGroundterminalblock(3P) M4 1.2~1.5N.m
Unit Powersupply Fanmotor
Model Hz Volts MCA MFA KW FLA
LEV22
50 220~240
0.23 16 0.02 0.06
LEV28 0.23 16 0.02 0.06
LEV36 0.23 16 0.02 0.06
LEV45 0.23 16 0.02 0.07
LEV56 0.23 16 0.02 0.07
LEV63 0.23 16 0.02 0.07
MCA:Min.CircuitAmps(A)
MFA :Max.FuseAmps(A)
KW :FanMotorRatedoutput(KW)
FLA :FullLoadAmps(A)
Model Powersupplywiring Remotecontrollerwiring
communicationwiring
PNV007 FieldELB WireandSize Wire Size
PNV009
16A
Mustcomply
withmaximum
currentandlocal
codes(≥0.75mm2)
Twisted-
pairwires ≥1.0mm2
PNV012
PNV015
PNV018
PNV021
Allfieldsuppliedpartsandmaterialsandelectricsworks must

conformtolocalcodes.
Usecopperwireonly.

Allwiringmustbeperformedbyanauthorizedelectrician.

Everyindoorunitmusthaveasubcirclebreakerandthewhole

systemmusthaveamaincirclebreaker.
Besuretogroundtheairconditioner.

Theapplianceshallbeinstalledinaccordancewithnational

wiringregulations,andshallbeprovidedto ensureall-pole
disconnectionfromthesupplymains,anddistancebetweenthe
polesshallbemorethan3mm.
CHECK ITEMS
BEFORE POWER ON
�
 Isthereanygasleakageatarenutconnections?
�
 Hastheheatinsulationbeencarriedoutatarenutconnection?
�
 Istheconnectingcablebeingxedtoterminalboardrmly?Isthe
connectingcablebeingclampedrmly?
�
 Isthedrainageok?
�
 (Referto"Checkthedrainage"section)
�
 Istheearthwireconnectionproperlydone?
�
 Istheindoorunitproperlyhookedtotheinstallationplate?
�
 Isthepowersupplyvoltagecompliedwithratedvalue?
AFTER POWER ON
�
 Isthereanyabnormalsound?
�
 Isthecoolingoperationnormal?
�
 Isthethermostatoperationnormal?
�
 Istheremotecontrol'sLCDoperationnormal?
NOTE:Forthepipingandwiringmethods,leakagetest,vacuumprocessandinstallationsetting
throughHMI,pleaserefterto“OutdoorunitInstallationManual”.
NOTE:Forhowtoconnectthepowerwireandcommunicationwirebetweenoutdoorunitandindoorunits,pleasereferto
chapter9“FieldWiring”inoutdoorunitinstallationmanual.