Airwell RCV03 User manual

RCV03
CONTENT
Parts and Functions............................................................................................................................ 1
Functional description......................................................................................................................... 2
REMOTE CONTROLLER OPERATION MANUAL
• Please read this operation manual before using the air conditioner.
• Please keep this manual carefully and safely.
22.AW.RCV03.UM.EN.12.09.Rev02

1
Parts and Functions
External View of Remote Controller
Remote Controller function description
This remote Controller is a general remote Controller, and some functions are valid according to the
adaptable model.
Turning on/o󰀨 the units
Switch operation modes
Set/cancel TURBO/QUIET functions
Set/cancel HEALTH functions
Set the Timer on/ Timer o󰀨 function.
Set/cancel SLEEP function
/1. Setting temperature increase or decrease.2.
Timing adjustment
Set the airow angle under the up and down swing.
Set the airow angle under the left and right swing.
Adjust the fan speed.
Set/cancel electrical heater function.
1. Set/cancel for menu function selection
2. Long press for 3 seconds to enter Wi-Fi mode
Press “OK/Wi-Fi” and “MENU” to access the lock function, and
then press again to cancel the lock function.
At the same time, press the “OK/Wi-Fi” and “HEATER” keys to
enter the lighting function.
For function selection, see menu function introduction for details.

2
Functional description
1. ON/OFF Button:
Turning on the units:Press the button to turning on the units.
Note: The initial default operation mode is AUTO and then will display the mode before turning o󰀨
Press button again to turn o󰀨 the unit.
2. MODE
Press the button every time, Function loop will be: → → → → → .
3. TURBO/QUIET
This function is valid under the mode of COOL and HEAT
Along with pressing the button each time, it will display according to the loop of TURBO→QUIET
→ Cancel →TURBO. Under the function of TURBO / QUIET.
When "SLEEP" is set, the " TURBO " function is disabled and the " QUIET " function is e󰀨ective.
4. HEALTH
(1) When turning on the units, press button, the remote controller will display " HEALTH ", and
then press button to cancel.
(2) When turning o󰀨 the units, press the button to enter FAN mode and display " HEALTH ".
5. TIMER
When the unit is in turning on status, users can only set the TIMER OFF, while in o󰀨 status, users can
only set the TIMER ON.
In O󰀨 status, press the button to enter the TIMER ON adjustment process.
In On status, Press the button to enter the TIMER OFF adjustment process.
When entering the timing adjustment process, timer ON/OFF icon and clock ash at the same time,
the initial default value is: 0:30. Press the / button once to increase or decrease the time for 30
minutes, and pressing and holding the button will speed up the adjustment.
After the time adjustment is completed, press the button again to conrm, the time static display,
and start the countdown.

3
6. SLEEP
(1) Valid during power on.
(2) Press the button, and the remote control will display “Sleep”. The SLEEP time is xed to 8
hours and is not adjustable
Press the button again, and the sleep function will be cancelled.
(3) It is invalid in FAN mode.
7. FAN SPEED Button
Each time the button is pressed, the cycle sequence is as follows:
8. Up-and-down SWING Angle Adjustment
Each time you press the button , Remote control display cycle sequence is as follows:
HEAT MODE:
Other modes:
9. Right-and-left SWING Angle
Each time you press the button , the remote control will display the following cycle:
Functional description
Low Medium High Auto

4
10. +/- Button
(1) This button is invalid in FAN mode;
(2) Press / button, temperature change 0.5°C; pressing and holding the button will change
quickly.
11. HEATER
Press the button, and the remote control will display “ HEATER “.
Press button again, the “ HEATER “ on the remote control will disappear, and the HEATER func-
tion will be turned o󰀨.
This function will be e󰀨ective only in AUTO and HEAT mode.
12.MENU
Functional cycle: SELF-CLEAN→3D AIR (reserved) →FRESH→HEALTH AIRFLOW→IFP→ →
→IFP AC OFF→IFP AC ECO→ → → → → → → →10°C
heating (Only valid in HEAT mode)→°F/°C→SELF-CLEAN
(1) Press button, the current function to be set ashes;
(2) Press button again to set/cancel the current setting function in the above sequence. If there is
no operation in 5 seconds, it will exit automatically.
Note:
Individual ap control for Round-way cassette: press button to enter function loop to select the
corresponding function icon and press button to conrm the operation, then press the button
to select the airow angles.
13. LOCK
Press the combination key and , and the remote control will display “ “. All buttons on the
remote control are invalid.
Press the combination button again to unlock the button and the icon “ “ will disappear.
Functional description

5
14. LIGHT
Press the combined button and to turn on the lighting function.
Press the combination key again and the light function turns o󰀨.
15. Wi-Fi
Press button 3s to enter Wi-Fi conguration, remote control display COOL mode, LOW fan speed,
30°C.
Functional description

WARNING :
The design and specifications are subject to change without prior notice for product improvement.
Consult with the sales agency or manufacturer for details.
ATTENTION :
Le design et les données techniques sont donnés à titre indicatif et peuvent être modifiés sans
préavis.
AIRWELL RESIDENTIAL SAS
10,Rue du Fort de Saint Cyr,
78180 Montigny le Bretonneux - France
www.airwell.com
21.AW.RCV03.UM.EN.12.13.Rev01