Airzone RADIANT365 User manual

rebmuNegaPdraobpilC
Installation Manual
RADIANT365
AZRA6CB1RAD + AZX6CM1VALR

1-8 ZONES (AZRA6CB1RAD+ AZX6CM1VALR)

4
INDEX
Warnings and environmental policy ..............................................................................................................................................................................6
Precautions........................................................................................................................................................................................................................6
Environmental policy .....................................................................................................................................................................................................6
System elements ...................................................................................................................................................................................................................7
Airzone RadianT VALR system for radiators main board (AZRA6CB1RAD)..................................................................................................7
Airzone control module for wireless valves VALR (AZX6CM1VALR) ..............................................................................................................7
Airzone wireless thermostatic valve actuator VALR for radiators (AZX6AC1VALR) ..................................................................................7
Airzone Blueface Color Thermostat Wired (AZRA6BLUEFACEC) .....................................................................................................................8
Airzone Think Monochrome thermostat Wired/Wireless (AZRA6THINK [C/R])..........................................................................................8
Airzone Lite thermostat Wired/Wireless (AZRA6LITE [C/R])..............................................................................................................................8
Webserver Airzone Cloud Ethernet/WI-FI DUAL 2.4-5G (AZX6WEBSCLOUDC/AZX6WSC5GER)..........................................................9
Cloud Ethernet Airzone production control board (AZX6CCPWSCC) ...........................................................................................................9
Airzone air to water HP gateway (AZX6GAW XXX) ..............................................................................................................................................9
General requirements.......................................................................................................................................................................................................10
Introduction .........................................................................................................................................................................................................................11
System installation............................................................................................................................................................................................................. 11
Assembly and connection............................................................................................................................................................................................... 12
AIRZONE RADIANT VALR SYSTEM FOR RADIATORS MAIN BOARD (AZRA6CB1RAD) ............................................................................ 12
Assembly ...................................................................................................................................................................................................................12
Connection ...............................................................................................................................................................................................................12
AIRZONE CONTROL MODULE FOR WIRELESS VALVES VALR (AZX6CM1VALR)........................................................................................ 14
Assembly ...................................................................................................................................................................................................................14
Connection ...............................................................................................................................................................................................................15
Reset............................................................................................................................................................................................................................15
AIRZONE WIRELESS THERMOSTATIC VALVE ACTUATOR VALR FOR RADIATORS (AZX6AC1VALR)................................................... 15
Assembly ...................................................................................................................................................................................................................15
Connection ...............................................................................................................................................................................................................16
Airzone Wired thermostats (AZRA6BLUEFACEC / AZRA6THINKC / AZRA6LITEC)................................................................................... 16
Assembly ...................................................................................................................................................................................................................16
Connection ...............................................................................................................................................................................................................16
Airzone Wireless thermostat (AZRA6THINKR / AZRA6LITER)......................................................................................................................... 17
Assembly ...................................................................................................................................................................................................................17
Changing batteries.................................................................................................................................................................................................17
Cloud ethernet Airzone production control board (AZX6CCPWSCC) ........................................................................................................ 18
Assembly ...................................................................................................................................................................................................................18
Connection ...............................................................................................................................................................................................................18
Configuration...........................................................................................................................................................................................................21
Airzone air to water HP gateway (AZX6GAW XXX) ........................................................................................................................................... 21
Assembly ...................................................................................................................................................................................................................21
Assembly and connection evaluation......................................................................................................................................................................... 21
Initial configuration ...........................................................................................................................................................................................................22
Airzone Blueface and Think thermostats ............................................................................................................................................................. 22
Airzone Lite thermostat..............................................................................................................................................................................................24
Initial Configuration evaluation ....................................................................................................................................................................................25

5
Advanced settings ............................................................................................................................................................................................................. 25
System parameters ......................................................................................................................................................................................................25
Zone Parameters...........................................................................................................................................................................................................26
Production parameters............................................................................................................................................................................................... 26
Self-diagnose.......................................................................................................................................................................................................................27
Airzone Blueface and Think thermostats (AZRA6BLUEFACEC / AZRA6THINK [C/R])............................................................................. 27
Blueface and Think Thermostats Warnings ................................................................................................................................................... 27
Blueface and Think Thermostats Errors........................................................................................................................................................... 27
Airzone Lite thermostat (AZRA6LITE [C/R]).......................................................................................................................................................... 32
LED Status .......................................................................................................................................................................................................................33
Navigation trees .................................................................................................................................................................................................................34
Navigation Tree - Blueface Thermostat................................................................................................................................................................. 34
Navigation Tree - Think Thermostat....................................................................................................................................................................... 35

6
WARNINGS AND ENVIRONMENTAL POLICY
PRECAUTIONS
For your security, and to protect the devices, follow these instructions:
•Do not handle the system with wet or damp hands.
•Disconnect the power supply before making any connections.
•Take care not to cause a short circuit in any of the system connections.
ENVIRONMENTAL POLICY
Do not dispose of this equipment in the household waste. Electrical and electronic
equipment contain substances that may damage the environment if they are not handled
appropriately. The symbol of a crossed-out waste bin indicates that electrical equipment
should be collected separately from other urban waste. For correct environmental
management, it must be taken to the collection centers provided for this purpose, at the end
of its useful life.
The equipment's components may be recycled. Act in accordance with current regulations
on environmental protection.
If you replace it with other equipment, you must return it to the distributor or take it to a
specialized collection center.
Those breaking the law or by-laws will be subject to such purposes and measures as are laid
down in environmental protection legislation.

7
SYSTEM ELEMENTS
AIRZONE RADIANT VALR SYSTEM FOR RADIATORS MAIN BOARD (AZRA6CB1RAD)
Configurable electronic board that controls the system through wired and wireless devices. Externally powered at 110 / 230
Vac. Wall mounted.
Functionalities:
•Control and management of the thermostats up to 8 zones - 10 wireless valves.
•Relay for boiler control through dry contact (NO).
•Relay for SHW control through dry contact (NO).
•Management of control gateways for production units.
Important: An Airzone Cloud Webserver and an Airzone Blueface thermostat are required.
- AZX6WEBSCLOUDC, AZX6WSCLOUDDINC and AZX6WSC5GER v.3.3.2 or later, or AZX6CCPWSCC.
- AZX6WEBSCLOUDR and AZX6WSCLOUDDINR incompatible.
- AZRA6BLUEFACEC v.5.3.0 or later.
AIRZONE CONTROL MODULE FOR WIRELESS VALVES VALR (AZX6CM1VALR)
Control module of radiant elements for heating stages by zone, through the management of
wireless valve actuators. Communications with the main control board, power supply through the
VALR Module bus and wireless communication with the valves. Mounted using DIN rail.
Functionalities:
•Control of up to 10 wireless valve actuators.
AIRZONE WIRELESS THERMOSTATIC VALVE ACTUATOR VALR FOR RADIATORS (AZX6AC1VALR)
Head with temperature probe to control the radiant stage of the zone by opening and closing its valve. Radio communications
through the Airzone wireless valve control module and powered by LR6 batteries.
LED display to show setpoint temperature, battery status and radio coverage.
•Valve open/close display (ON/OFF)
•Operation as normally closed.
•Includes adapters for different connection diameters.
•Anti-freeze function.
•Anti-calc function.
•Child lock function.

8
AIRZONE BLUEFACE COLOR THERMOSTAT WIRED (AZRA6BLUEFACEC)
Color graphic interface with capacitive screen for controlling zones in Airzone systems. Powered by main control board.
Finished in steel and glass. Available in white and black.
Functionalities:
•Available in Spanish, English, French, Italian, German and Portuguese.
•Control of temperature and Operation mode (Master thermostat).
•Room temperature and relative humidity measurement of the zone.
•Eco-Adapt function.
•Sleep function.
•Temperature and mode time schedules.
•Remote access to other zones of the system.
•Weather forecast (optional).
AIRZONE THINK MONOCHROME THERMOSTAT WIRED/WIRELESS (AZRA6THINK [C/R])
Graphic interface with low-energy e-ink screen and capacitive buttons for controlling zones in Airzone systems. Finished in
steel and glass. Wired/wireless communications. Powered from main control board (wired) or by CR2450 button battery
(wireless). Available in white and black.
Functionalities:
•Available in Spanish, English, French, Italian, German and Portuguese.
•Control of temperature and Operation mode (Master thermostat).
•Room temperature and relative humidity reading.
•Sleep function.
•Remote access to other zones of the system.
•Weather forecast (optional).
AIRZONE LITE THERMOSTAT WIRED/WIRELESS (AZRA6LITE [C/R])
Thermostat with capacitive buttons for controlling the temperature of the zones in Airzone
systems. Finished in steel and glass. Wired/wireless communications. Powered from main
control board (wired) or by CR2450 button battery (wireless). Available in white and black.
Functionalities:
•On/off of the zone.
•Set-point temperature control (Accuracy: ± 1ºC, max: ±3ºC.)
•Room temperature and relative humidity reading.

9
WEBSERVER AIRZONE CLOUD WI-FI DUAL 2.4-5G (AZX6WSC5GER)
Webserver for controlling Airzone systems through Airzone Cloud platform. Accessible through browser or App (available for
IOS and Android). Connected to router via WiFi (AZX6WSC5GER). Power supplied through Control Board.
Functionalities:
•Control of up to 32 systems.
•Configuration and control of zone parameters (Room
and set-point temp., operating mode, etc.) and system
parameters via Airzone Cloud.
•Temperature and Operation mode time schedules.
•Multi-user and multi-session.
•External control through Airzone Cloud platform.
•Remote updates of the Webserver firmware and the systems connected to it.
•Remote error detection and error resolution.
CLOUD ETHERNET AIRZONE PRODUCTION CONTROL BOARD (AZX6CCPWSCC)
Control board of production units with webserver for controlling Airzone systems through Cloud platform. Connected to router
via Ethernet and communications through domotic bus. Externally powered at 110/230 Vac. Wall mounted.
Features:
•Controls up to 32 systems.
•7 control relays for cooling/heating modes, cooling/heating air demand,
cooling/heating radiant demand.
•Inputs for semi-forced modes, boiler probe and DHW control.
•Configuration and control of zone parameters (Room and set-point temp., operating
mode, etc.) and system parameters via Airzone Cloud.
•Temperature and operating mode time schedules.
•Multi-user and multi-session.
•Remote management of firmware updates and errors.
AIRZONE AIR TO WATER HP GATEWAY (AZX6GAW XXX)
Communication gateway between Airzone system and Air to water units. Powered through the AC unit bus of the production
control board (AZX6CCPWSCC).
Features:
•Two-way communication of the basic control parameters depending on the demand of the
Airzone control system.
•Reading of errors of the controlled unit.
•Imposes water production temperature based on the demand.
Important: Not available for installations with AZX6CCP.
AZX6WSC5GER

10
GENERAL REQUIREMENTS
Strictly follow the directions outlined in this manual:
•The system must be installed by a qualified technician.
•Verify that the units to be controlled have been installed according to the manufacturer's requirements and operate
correctly before installing the Airzone System.
•Locate and connect all the devices of the installation in accordance with the electronic regulations in force.
•Verify that the air conditioning installation to be controlled is in accordance with the regulations in force.
•It is necessary to use a Blueface Thermostat to have all the features of the Airzone system.
•Follow these recommendations to locate the thermostats:
•Perform all the connections with total abscense of power suppliance.
•In order to connect the elements of the system, use Airzone cable: shielded twisted pair cable formed by 4 wires: 2x0,22
mm2+ 2x0,5mm2(AWG 20 – 4 wired).
•Do not place the system bus close to high power lines, fluorescent lights, LED lamps, motors, etc. It might cause
interference on the communications.
•Respect the connection polarity of each device. A wrong connection may seriously damage the product.
•For elements externally powered at 110 /230 Vac, for the communications, it is only necessary to connect the poles "A"
and "B" of the bus.
•For elements externally powered at 110/230 Vac, respect the connection polarity. A wrong grounding may produce
electric shocks.
•According to the current local and national regulations, it is mandatory to add a switch (or other element to disconnect
the system) to the external supply wiring so that a constant separation between poles is guaranteed. The system will
restart automatically if the supply is eventually turned off. Use an independent circuit from the controlled system
for the power supply.
Important: A Webserver Airzone Cloud is required for the proper functioning of the system.

11
INTRODUCTION
Airzone systems enable the management of Master and Zone interfaces. Master thermostats enable mode management or
define the efficiency level with the Eco-Adapt function.
Remember: This system only admits one Master thermostat.
To distinguish a Master Interface from a Zone Interface, check the next points.
•Blueface Master: Mode and Eco-Adapt icons shown in white color.
•Blueface Zone: Mode and Eco-Adapt icons shown in gray color.
SYSTEM INSTALLATION
Before the Airzone system commissioning, please check:
•The system is going to control works correctly without the Airzone system installed.
Important: For installations with radiant surfaces only, it is recommended the installation of buffer tanks.
In order to install the Airzone system, carefully follow these steps:
Connect all the necessary elements (see sections Assembly and Connection).
Connect all the elements of the system (thermostats, modules, etc.)
Power the main board.
Check all the assembly and the connection are correct (see section Assembly and Connection evaluation).
Configure the system.
Configure all the thermostats (see sections System Start-up and Advanced settings).
If you have any other doubt, check the user and installation manuals.
Access all our technical documents and the self-diagnosis section, check the most FAQs, certificates,
watch our videos and read our declaration of conformity at: myzone.airzone.es/productos/

12
ASSEMBLY AND CONNECTION
AIRZONE RADIANT VALR SYSTEM FOR RADIATORS MAIN BOARD (AZRA6CB1RAD)
Assembly
The production control board is supplied in a box to be screwed to the wall. It is should be placed and mounted in accordance
with the current electrotechnical regulations.
For the mounting of the main control board, follow the following steps:
•Locate the control board close to the unit to be controlled.
•Unscrew the cover securing the back part to the wall.
•Make all the connections and screw the cover again.
Connection
Airzone connection bus connectors
The Airzone connection bus allows you to connect all the internal components dependent on the main board to control up to
8 zones. These are the elements that can be connected:
•Blueface (AZRA6BLUEFACEC), Think (AZRA6THINKC) and Lite (AZRA6LITEC) thermostats.
If using a wired thermostat, connect it in one of the 3 Airzone connection bus terminals. The
connection can be both a Bus connection or a star connection. Use (2x0.5+2x0.22 mm2) Airzone
wire. For added security, secure the wires using the turrets.
In case of wireless element, check it has the battery on.
No.
Description
Airzone connection bus
Wireless Module
SW1
Webserver Airzone Cloud
AC unit bus
VALR module bus
DHW control
Boiler control
Power

13
SW1
The main control board can also connect to Airzone wireless elements. These elements are associated by
opening the wireless association module of the main control board. Press on SW1 and wait for the LED 19
to remain red. The wireless association module will be open during 15 minutes.
Reset system: If you want to return to factory values, press and hold on SW1 until LED D19 stops blinking.
VALR module bus connector
The VALR module bus is intended to connect the AZX6CM1VALR module.
It has a 5-pin terminal for the VALR module bus connection. Attach the wires with the terminal
screws following the color code.
AC unit bus connector
The AC unit bus allows you to connect different Airzone air to water HP gateways AZX6GAWXXX.
To connect gateways, disconnect the AC unit bus terminal and insert the connector and the fixing post of the gateway.
Boiler connector
This output can be configured as boiler control. (See Blueface Advanced Configuration Menu, system parameters)
Boiler configuration
Status
Stop
Heating radiant
Demand ON
BOIL. OFF
BOIL. ON
Demand OFF
BOIL. OFF
BOIL. OFF
Relay specs: Imax = 12 A at 24Vdc or 250Vac, voltage-free.
DHW control
It allows to turn on/off the Domestic Heat Water (DHW) function.
Power supply connector
This connector powers the main control board and all the elements connected to it. Externally
powered at 110/110/230 Vac. It is connected through a 3-pin terminal. Attach the wires with the
terminal screws following the color code.

14
For added security, secure the wires using the turret.
According to the current local and national regulations, it is mandatory to add a switch (or other element
to disconnect the system) to the external supply wiring so that a constant separation between poles is
guaranteed. The system will restart automatically if the supply is eventually turned off. Use an
independent circuit from the controlled system for the power supply.
Remember: Once all the connections are made, make sure you replace the cover properly.
AIRZONE CONTROL MODULE FOR WIRELESS VALVES VALR (AZX6CM1VALR)
Assembly
This module is mounted on DIN rail. It should be placed and mounted in accordance with the current electrotechnical
regulations.
Note: To take the module away, pull the reed down to release it.

15
Connection
Connect the AZX6CM1VALR module to the VALR Module bus of the RadianT main control board.
For the connection to the Airzone main board, press the module association button .
Reset
If you want to return to factory values, press and hold the button until LED change to searching status (blue). Wait for
the LEDS to go back to their normal state before starting with the initial configuration process.
AIRZONE WIRELESS THERMOSTATIC VALVE ACTUATOR VALR FOR RADIATORS (AZX6AC1VALR)
Assembly
Airzone wireless thermostatic valve actuators are mounted on each of the valves of a heater. Check that the thermostatic
valve actuator is compatible with the valve body that you are going to equip (M30 x 1.5). See compatibility table.

16
Connection
To associate the heads, follow the steps below:
1. Synchronize the AZRA6CM1VALR module with the system's main control board.
2. Turn the upper wheel of the head until "OF" appears on the screen.
3. Press the upper button to address each thermostatic head (an address from 01 to 10 is automatically assigned).
AIRZONE WIRED THERMOSTATS (AZRA6BLUEFACEC / AZRA6THINKC / AZRA6LITEC)
Assembly
Wired thermostats are mounted on the wall through a support. It is recommended not to locate it more than 40 meters away
from the main control board. To fix it to the wall, follow these steps:
•Separate the back part of the thermostat from the wall support and make all the
connections.
•Fix the back part of the thermostat to the wall.
•Place the display on the support once it is fixed.
•Place the anti-theft rods for additional support (optional).
Connection
The Airzone thermostats are connected to the Airzone connection bus of the main board.
Attach the wires with the terminal screws following the color code.
Important: Use a suitable screwdriver to press in the locking tabs.
Note: To connect more than 4 Blueface, it is necessary an external power supply (AZX6POWER). These values can be altered
depending on the separation distance among them.

17
AIRZONE WIRELESS THERMOSTAT (AZRA6THINKR / AZRA6LITER)
Assembly
Wireless thermostats are mounted on the wall through a support. It is recommended not to locate it more than 40 meters away
from the main control board.
To fix it to the wall, follow these steps:
•Remove the back of the thermostat and insert the CR2450 button battery.
•Fix the back part of the thermostat to the wall.
•Place the display on the support once it is fixed.
•Place the anti-theft rods for additional support.
Changing batteries
When a wireless Think thermostat is running out of battery, it displays this icon on the screensaver. In the case of wireless
Lite thermostats, a warning message will be displayed on the Blueface. In order to know the zone of the Lite thermostat(s)
running out of battery press on the warning icon.
To replace the battery, separate the thermostat from its support and replace the battery (CR2450).
Important: We recommend using of top-brand batteries. Using low-quality batteries may reduce the duration of use.
Remember to deposit the old battery into an appropriate recycling point.
Note: Do not forget to remove the security system before taking away the thermostat from the wall.

18
CLOUD ETHERNET AIRZONE PRODUCTION CONTROL BOARD (AZX6CCPWSCC)
Assembly
The production control board is supplied to be screwed to the wall. It should be placed and
mounted in accordance with the current electrotechnical regulations. For the mounting of the
main control board, follow the following steps:
•Locate the control board close to the unit to be controlled.
•Unscrew the cover securing the back part to the wall.
•Make all the connections and screw the cover again.
Connection
Production control board is connected to the domotic bus of the main board.
Power supply connector
This connector powers the main control board and all the elements connected to it. Externally
powered at 110/110/230 Vac. It is connected through a 3-pin terminal. Attach the wires with the
terminal screws following the color code. For added security, secure the wires using the turret.
Important: According to the current local and national regulations, it is mandatory to add a switch (or other element to
disconnect the system) to the external supply wiring so that a constant separation between poles is guaranteed. The system
will restart automatically if the supply is eventually turned off.
Nº
Description
Power supply
ACS Deactivates the air conditioning through AC unit
CALOR Sets the heating semi-forced mode
FRIO Sets the cooling semi-forced mode
STOP Imposes the Stop mode in the system
SONDA Boiler probe
Domotic bus output 1
Domotic bus output 2 – Aerothermal gateway connection
Ethernet
O1
Cooling mode
O2
Heating mode
O3
Cooling air demand
O4
Cooling radiant demand
O5
Heating air demand
O6
Radiant heating demand
O7
Reserved for internal use
SW2

19
Remember: Once all the connections are made, make sure you replace the cover properly.
Digital inputs
The production control board has 4 digital inputs to externally control the Airzone systems. These inputs are configured as
normally open. It is recommended to use a shielded cable to connect it.
ACS: This input activates the DHW mode: all the systems working on Air heat will stop and the message DHW will be displayed
by the zone thermostats. This feature is recommended for Aerothermal installations when the Aerothermal unit starts
producing DHW.
CALOR: This input activates the semi-forced heating mode in all the system of the installation. These are the modes available
to select: Stop, Heating and Ventilation.
FRIO: This input activates the semi-forced cooling mode in all the system of the installation. These are the modes available to
select: Stop, Cooling, Dry and Ventilation.
STOP: This input activates the Stop mode in all the system of the installation.
The main control board has an analogical input to connect a temperature probe for boiler protection.
Domotic bus connectors
The indoor domotic bus allows you to connect the production control board with the main control
board and aerothermal gateways (AZX6GAWxxx). The domotic bus has two terminals which are
interconnected so that can be used interchangeably. This system can only be connected by bus. Attach
the wires with the terminal screws following the color code. Use the shield only on the connector of the
main control board, not required in RadianT system.
Note: For a proper operation of this main control board, all main control boards must be addressed (up to
32 zones) (see section Advanced settings).
Control relays
This device has 7 relays for controlling the installation. The characteristics of the control relays are Imax: 10 A at 110/230 Vac
(tension-free). Note that to control elements with a greater power, it is recommended to use contactors in accordance with the
power required.
Important: Remember to connect the neutral connector directly from the circuit to the element to be controlled.
Depending on the type of installation, the control relays will follow a different logic:
Aerothermal
Mode Demand
Control Relays
FRIO_Y
CALORB_W
AIRE_Y
RADIANTE_Y
AIRE_W
RADIANTE_W
Stop
Off
--
--
--
--
--
--
Cooling
mode
Air
ON
--
ON
--
--
--
Radiant
ON
--
--
ON
--
--
Off
--
--
--
--
--
--

20
Heating
mode
Air
--
ON
--
--
ON
--
Radiant
--
ON
--
--
--
ON
Off
--
--
--
--
--
--
Off
2 pipes / 4 pipes
Mode Demand
Control Relays
FRIO_Y
CALORB_W
AIRE_Y
RADIANTE_Y
AIRE_W
RADIANTE_W
Stop
Off
--
--
--
--
--
--
Cooling
mode
Air
ON
--
ON
--
--
--
Radiant
ON
--
--
ON
--
--
Off
ON
--
--
--
--
--
Heating
mode
Air
--
ON
--
--
ON
--
Radiant
--
ON
--
--
--
ON
Off
--
ON
--
--
--
--
RadianT
Mode Demand
Control Relays
FRIO_Y
CALORB_W
AIRE_Y
RADIANTE_Y
AIRE_W
RADIANTE_W
Stop
Off
--
--
--
--
--
--
Cooling
mode
Radiante
ON
--
--
ON
--
--
Off
--
--
--
--
--
--
Heating
mode
Radiante
--
ON
--
--
--
ON
Off
--
--
--
--
--
--
Dew
warning
active
Radiant ON -- ON -- -- --
Important: In order to optimize the production temperature of the aerothermal units, the following combinations will not
generate air demand in the production control board:
Communication gateway (AZX6QADAPTxxx / AZX6QADAPT3xxx) in Flexa 3.0, Innobus Pro6, Acuazone and Innobus Pro32 main
control boards.
Controller 3.0 gateway (AZX6GTCxxx) in Flexa 3.0, Innobus Pro6, Acuazone and Innobus Pro32 main control boards.
Communication gateway for electromechanical units (AZX6ELECTROMEC) in Flexa 3.0, Innobus Pro6, Acuazone and Innobus
Pro32 main control boards.
Infrared gateway module (AZDI6MCIFR [C/R]) in Acuazone e Innobus Pro32 systems (when configured as a zoning system or
mixed system).
Gateway module (AZDI6MCIFR [C/R]) in Acuazone e Innobus Pro32 systems (when configured as a zoning system or mixed
system).
Important: To guarantee the optimization of the production temperature of the aerothermal units, these device combinations
do not generate radiant demand to the production control board:
Zoning module for Electrical Heating Element (AZDI6MZSRE [C/R]) in Acuazone and Innobus Pro32 systems regardless of the
Main Control Board configuration.
SW2
To force the production control board to search for the connected systems and save the configuration of the
installation, press SW2.

21
Configuration
It is required to configure the relays control logic for the production control board, as well as the other parameters of the cloud
production control board. The cloud production control board settings are only available in the master Blueface thermostat of
the system nº1 (see section Production Parameters).
AIRZONE AIR TO WATER HP GATEWAY (AZX6GAW XXX)
Assembly
The Airzone air to water gateway is integrated into the domotic bus of the Cloud Ethernet Production Control Board,
(AZX6CCPWSCC). It has a 4-pin terminal. Disconnect the terminal to which you want to connect to the Webserver and fit the
connector.
ASSEMBLY AND CONNECTION EVALUATION
Check the following aspects:
-The state of the LEDs of the main control board and the rest of control elements. Check the self-diagnose section of
the data sheet of the elements.
-If all the thermostats are powered.
Important: In the main control board, to verify the correct performance, check D3, D11 and D19 LEDs.
Meaning
D3
Main control board activity
Blinking
Green
D11
Main control board power
Solid
Red
D19
Association channel: active
Solid
Red