Airzone Lutron User manual

Installation Manual

2
ES
EN
FR
IT
PT
DE
TABLE OF CONTENTS
Overview ..................................................................................................................................................................................................................................3
Description and Features..............................................................................................................................................................................................3
System Outline .................................................................................................................................................................................................................3
Specifications and elements of the Airzone-Lutron interface..........................................................................................................................4
Installation...............................................................................................................................................................................................................................5
Installation on the Main Board....................................................................................................................................................................................5
System identification......................................................................................................................................................................................................5
Configuration .........................................................................................................................................................................................................................6
Configuration modes with Lutron systems............................................................................................................................................................6
Configuration with Lutron Palladiom thermostat to control the HVAC zone.......................................................................................6
Configuration with Airzone thermostat.............................................................................................................................................................6
Lutron Configuration .....................................................................................................................................................................................................7
Airzone system Configuration ....................................................................................................................................................................................8
System configuration for ACUAZONE / IBPRO32 and FLEXA 3.0 / IBPRO6.............................................................................................8
System configuration for VAF and ZBS ..............................................................................................................................................................9
System configuration for 2 PIPES / 2 WIRES......................................................................................................................................................9
Load the configuration into the Homeworks QS..................................................................................................................................................9
Troubleshooting.................................................................................................................................................................................................................10
The Airzone System does not detect the Airzone-Lutron interface............................................................................................................ 10
The Airzone-Lutron interface cannot be connected ........................................................................................................................................ 10

3
ES
EN
FR
IT
PT
DE
OVERVIEW
DESCRIPTION AND FEATURES
The Airzone-Lutron interface allows the integration of Lutron control systems on Airzone systems through the Lutron
HomeWorks QS Processor.
The Airzone-Lutron interface is a Plug&Play device for Airzone systems which, using the telnet protocol, enables the
following actions:
•Reading/Writing of the room temperature.
•Reading/Writing of the set-point temperature.
•Reading/Writing of the operating mode.
•Reading/Writing of the cooling/heating demand.
•Reading/Writing of the fan speeds.
The system requires the connection of at least one Airzone Blueface Thermostat. It allows the control of the conditioning of
each zone associated from Lutron Keypads devices, and the control of time schedules both from the HomeWorks QS Processor
and from the Lutron Connect App.
The Airzone-Lutron also allows its use as Airzone Cloud Webserver Ethernet (AZX6WEBSCLOUDC), for further information about
its usage, please refer to the installation manual (MI_AZ6_WSCLOUD_A5_MUL) and user’s manual
(MU_AZ6_WSCLOUD_A5_MUL).
SYSTEM OUTLINE
Lutron typical layouts is as follows:
For RadianT365, the typical connection involves the Production Control Board (AZX6CCP):
Important: The Airzone-Lutron interface enables the control of up to 32 Airzone systems simultaneously from a single
HomeWorks QS system.
AZX6GTILUT
LUTRON HOMEWORKS QS PROCESSOR
MAIN CONTROL BOARD
SWITCH
AZX6CCP
LUTRON HOMEWORKS QS PROCESSOR
MAIN CONTROL BOARD
SWITCH

4
ES
EN
FR
IT
PT
DE
SPECIFICATIONS AND ELEMENTS OF THE AIRZONE-LUTRON INTERFACE
Note: For further information, please refer to the associated datasheet: FTAZX6GTILUT.
Power supply and consumption
Ethernet
Type of power supply Vac Type of cable UTP cat 6
V max. 12 V supplied from
the Control Board
Standard T568B
IP address setting Static
I max. 200 mA Mechanical aspects
Maximum consumption 1.8 W Dimensions (WxHxD) 130x40x39.5 mm
Operative temperatures
Storage -20 to 70 °C
Operation 0 to 50°C
Operating humidity range
5 to 90%
(non-condesing)
W
H
D
Meaning
D5
Ethernet connected Blinking Green
D4
Ethernet activity Blinking Yellow
D7 Data transmission from automation Blinking Red
D8 Data reception from automation bus Blinking Green
D9 Microswitch performance Blinking Green
D10 Connected to the Internet Blinking Green
D11 Network data transmission Blinking Red
D12 Network data reception Blinking Green
D13 Configured as IP address through DHCP On Red
Configured as Fixed IP address Off
D15 Power supply Solid Red
Meaning
Ethernet
Automation bus output
Automation bus input

5
ES
EN
FR
IT
PT
DE
INSTALLATION
The Airzone-Lutron interface operates as an interpreter using the services defined by the Lutron HomeWorks QS Processor to
connect Lutron and Airzone systems via Ethernet using the Lutron integration protocol.
Note: The HomeWorks QS Processor and the Palladiom thermostat must use software version 13.0 or newer.
The Airzone-Lutron interface is a Plug&Play device which, when connected to the Airzone Main Control Board and to the
HomeWorks QS Processor via Ethernet using the Lutron integration protocol, configures itself and configures the Main Board
to work with the Lutron system.
Important: It is necessary to have at least one Airzone Blueface thermostat connected all the time.
INSTALLATION ON THE MAIN BOARD
The Airzone-Lutron interface connects to the Airzone Main Control Board using the automation bus.
The ethernet cable should be connected to the Airzone-Lutron interface. Once the control board has the interface connected,
it will auto-detect the presence of the interface and will automatically set the parameters to enable the operation with the
Lutron system.
SYSTEM IDENTIFICATION
To start the configuration process, it is necessary to identify the system, to do this, remove the Blueface thermostat from its
base and check the code printed on the label located on the back of the thermostat.
Depending on the code printed on the label the system will be configured in different ways, for further information, please
refer to the documentation related to each system:
Identification
Related documentation
AZCE6
Flexa 3.0 / Innobus Pro6 System
Quick Guide
Installation Manual
AZDI6
Acuazone / Innobus Pro32 System
Quick Guide
Installation Manual
AZRA6
RadianT365 System
Quick Guide
Installation Manual
AZVAF
VAF System
Quick Guide
Installation Manual
AZZBS
ZBS System
Quick Guide
Installation Manual
AZZS6
2 pipes / 2 wires System
Quick Guide
Installation Manual

6
ES
EN
FR
IT
PT
DE
CONFIGURATION
CONFIGURATION MODES WITH LUTRON SYSTEMS
Depending on the existence or absence of Airzone thermostats in the zones, there are two available configurations.
Regardless of which thermostats are used, the HomeWorks QS system will have full control of the HVAC zones from the keypads,
time clocks and the Lutron Connect App.
Configuration with Lutron Palladiom thermostat to control the HVAC zone
When a Lutron Palladiom thermostat is used to control an HVAC zone, there are two integration commands used. First,
depending on the type of HVAC system, the Airzone-Lutron interface will use DEVICE commands to read the current
temperature from the Palladiom thermostat. Second, the Airzone-Lutron interface will use HVAC commands for control of the
set-point temperature, operating mode and fan speed.
The Integration IDs of the DEVICE and HVAC commands must follow the rules below:
When the system uses Lutron Palladiom thermostats, it uses DEVICE commands to read the room temperature with the
Integration ID: 2XXYY format, where XX stands for the system’s number and YY stands for the zone’s number.
XX 01 for Airzone system 1, 02 for Airzone system 2... Up to 32 Airzone systems.
YY 01 for Airzone zone 1, 02 for Airzone zone 2... Up to 32 Airzone zones per system (based on the type of the system).
Example: A Palladiom thermostat DEVICE Integration ID for the Airzone system 1 and for zone 1 will be 20101.
The Airzone system uses HVAC Integration IDs to control the set-point temperature, operating mode and fan speeds using the
Integration ID: 1XXYY format, where XX stands for the system’s number and YY stands for the HVAC zone’s number.
XX 01 for Airzone system 1, 02 for Airzone system 2... Up to 32 Airzone systems.
YY 01 for Airzone zone 1, 02 for Airzone zone 2... Up to 32 Airzone zones per system (based on the type of the system).
Example: A HVAC Integration ID for the Airzone system 1 and for the zone 2 will be 10102.
Configuration with Airzone thermostat
When an Airzone thermostat is used to control an HVAC zone, HVAC integration commands are used for control of set-point
temperature, operating mode and fan speed.
The Airzone system uses HVAC Integration IDs to identify and to associate the system and the HVAC zone with the Integration
ID: 1XXYY format, where XX stands for the system’s number and YY stands for the HVAC zone’s number.
XX 01 for Airzone system 1, 02 for Airzone system 2... Up to 32 Airzone systems.
YY 01 for Airzone zone 1, 02 for Airzone zone 2... Up to 32 Airzone zones per system (based on the type of the system).
Example: A HVAC Integration ID for the Airzone system 1 and for the zone 3 will be 10103.

7
ES
EN
FR
IT
PT
DE
LUTRON CONFIGURATION
To perform the integration with the Airzone system in the HomeWorks QS software, please follow the steps below:
1. Define the HVAC zones in the software in the menu design – loads and select HVAC zones.
Important: On zoned ducted units the Fan Speed option enabled must be Auto. The “Auto” Operating Mode is only available
for Airzone systems in North America.
2. For Palladiom thermostats, add them to the rooms in the design – controls screen. After adding a thermostat, you
must assign the HVAC zone it will control in the Remote Zone setting.
3. Define the Airzone-Lutron interface in the design – equipment screen. Add a “3rd Party HVAC” device and name it
“Airzone System”. In the Manufacturer drop down, select “Generic (via integration)”. For Setpoint type, select “Dual”. In
the output table, click on Assign and add all the HVAC zones you created previously.
Note: The UID must be unique for each zone. Set the minimum and maximum Setpoint at 19ºC and 30ºC respectively. Set
the same differential value of Minimum Heat/Cool as Lutron System in case of Setpoint Dual.
4. On the navbar, click Tools and select Configure Integration.

8
ES
EN
FR
IT
PT
DE
5. Select the Integration tab and then in the drop down box for Assign integration IDs, select “Devices”. Now you must
manually assign the Integration IDs of the Palladiom thermostats in the format 2XXYY as described on page 6.
Next, in the drop down box for Assign integration IDs, select “HVAC”. Now you must manually assign the Integration
IDs of the HVAC zones in the format 1XXYY as described on page 6.
6. While still in the Configure Integration screen, select the tab “Telnet Logins”. Add the Username and Passphrase the
Airzone-Lutron interface will use to make a Telnet connection with the HomeWorks QS processor.
AIRZONE SYSTEM CONFIGURATION
System configuration for ACUAZONE / IBPRO32, FLEXA 3.0 / IBPRO6 and RADIANT365
For Acuazone / IBPRO32, FLEXA 3.0 / IBPRO6 and RADIANT365 go to the main screen, press the icon, select information
and press Webserver.
Inside the Webserver menu, press the settings icon and set the static IP address, for example 192.168.100.207

9
ES
EN
FR
IT
PT
DE
System configuration for VAF and ZBS
For VAF and ZBS, go to the main screen, press the user settings icon and select the information parameter, once in, press
Webserver to access.
Inside the menu, press the settings icon and set the static IP address, for example 192.168.100.207
System configuration for 2 PIPES / 2 WIRES
For 2 pipes / 2 wires systems, go to the main screen, press the settings icon, enter the access pattern and select system settings,
once in, find and press BACnet to access.
Inside the menu, press the settings icon and set the static IP address, for example 192.168.100.207
LOAD THE CONFIGURATION INTO THE HOMEWORKS QS
Using a web browser, open the IP address established on the Airzone Blueface thermostat (see section Airzone system
configuration), enter the username “airzone” and the pass “lutron” in the access pop-up window. Next, set the Username and
Passphrase to match those created in the HWQS software in step 6 as described on page 8. In the Lutron IP Gateway field, enter
the IP address of the Lutron HomeWorks QS Processor and click Set IP.

10
ES
EN
FR
IT
PT
DE
TROUBLESHOOTING
THE AIRZONE SYSTEM DOES NOT DETECT THE AIRZONE-LUTRON INTERFACE
Verify the following items:
1. The D9 LED (Microswitch performance) is blinking.
2. The D7 and D8 LEDs are alternately blinking.
3. The correct connection between the Airzone-Lutron Interface in the Airzone Main Control Board.
THE AIRZONE-LUTRON INTERFACE CANNOT BE CONNECTED
Verify the following items:
1. LEDs “A” and “B” are blinking, and those in the Ethernet connector are active.
2. Check that the Ethernet cable is properly connected.

www.lutron.com
Parque Tecnológico de Andalucía
C/ Marie Curie, 21 – 29590
Campanillas – Málaga - España
Teléfono: [phone]
Fax: [phone]
http://www.myzone.airzone.es
Parc Tertiaire Silic – Inmeuble Panama
45 Rue Villeneuve
94573 Rungis - France
Téléphone : [phone]
Fax : [phone]
http://www.myzone.airzonefrance.fr
Via Fabio Filzi, 19/E – 20032
Cormano – Milano - Italia
Telefono: [phone]
Fax: [phone]
http://www.myzone.airzoneitalia.it