Airzone OneZone User manual

1
OneZone
User’s Manual
Takes care of the temperature of your most special room

2
Contents
OneZone is an Airzone product........................................................................................................ 3
How does OneZone work? ............................................................................................................... 3
Content of the box ............................................................................................................................ 3
Description of the thermostat icons.................................................................................................. 3
Installation ........................................................................................................................................ 3
Damper Installation .......................................................................................................................... 4
Thermostat Installation..................................................................................................................... 5
Location of the thermostat................................................................................................................ 6
OneZone thermostat capabilities ...................................................................................................... 6
Selection of the temperature units .................................................................................................... 6
OneZone operation modes................................................................................................................ 7
Thermostat Utilization...................................................................................................................... 7
Additional functionalities of the OneZone thermostat ..................................................................... 8
Setup and modification of the Day and hour.................................................................................... 8
Batteries replacement ....................................................................................................................... 9
Thermostat battery replacement ................................................................................................. 10
Replacement of the damper control module batteries ................................................................ 10
Do you want to extend the OneZone comfort throughout the house?............................................ 11
Environmental Policy ..................................................................................................................... 11

3
OneZone is an Airzone product.
Airzone has been leading the air conditioning zoning market for more than to 10 years. Airzone
researches, develops, produces and commercializes advanced zoning systems for air conditioning
designed to guarantee the comfort in any place of the homes, at any time.
How does OneZone work?
OneZone consists of a motorized damper and an infrared digital thermostat. This technology allows the damper and
thermostat of the selected room to communicate without the need of cables. The operation is very simple: the
thermostat analyzes the temperature of the room and, according to the programmed temperature, it opens the
damper to control the air flow to cold or heat the room. When the temperature reaches the set point temperature,
the damper is closed automatically.
Important: OneZone controls the damper by means of the thermostat but it does not control the operation of
the air conditioning unit. Because of that, the AC unit must be running to have air conditioning in the room.
Content of the box
The box contains:
- A OneZone damper
- A metallic clip to mount the control module to the damper
- A OneZone thermostat
- A Battery Box including the damper control module
Description of the thermostat icons
Installation
Necessary Tools:
Screwdriver

4
Damper Installation
1.- Install the clip in the edge of the damper
2.- Slide the control module of control in
the clip
3.- Connect the damper motor cable in
the connector provided in the control
module
- 4. Verify that the damper communicates with the thermostat. Press the ON icon, be sure that the thermostat this
in cold mode and lower the temperature to 65F. The damper must open. If that does not happen, raise the
temperature to the maximum, wait for about 20 seconds and return to lower the temperature to 65F. If the damper
does not even move, please read the detailed manual at www.airzoneusa.com/onezone/manual.
- 5. Remove the grille of the air access to the room.
- 6. Verify that the damper enters in the end of the air supply duct. It is possible that the duct size is not compatible
with the size of the damper. If this is the case, please contact the supplier of your system.
7. –Insert the dámper in the air access duct.

5
Thermostat Installation
1.- Fix the base to the wall If screws are used, you will have to disassemble the thermostat from its base
before, as it is indicated below:
Detach the thermostat from the base using a coin
2.- Once fixed the base to the wall, if the thermostat had to be disassembled, reassemble to its base as
indicated below:
Insert the panel in the guides in the superior part of the base of the thermostat and close the thermostat
8.- Fix the IR receiver with the stick tape on the grid,
pointing towards the final position of the thermostat
9.- Replace the grille in its original position

6
• 3. – Verify the operation of the system. If the thermostat does not have indication of the temperature, power it on
by touching briefly the ON/OFF icon, Verify that the air equipment this running and set the temperature of the
thermostat to the minimum and maximum verifying that depending on the setting the air flows or not through the
grille. Then, set the temperature to the desired value.
Location of the thermostat
One of the most important issues for the correct operation of the system is the location of the thermostat.
The correct location is:
In an area with air circulation
Away from direct currents of cold or hot air
Away from sources of heat such as heaters or radiators.
Out of direct sun exposure.
Preferably not installed on exterior walls.
NOTE: Before affixing the thermostat in the wall, be sure that the thermostat can control the damper. To do that,
with the thermostat held in its location, repeat the procedure described in the installation section of the damper.
Only if the damper operates, then you can set the thermostat in that place.
OneZone thermostat capabilities
- Activate/Deactivate the zone temperature control (ON/OFF).
- Setting of the set point temperature (temperature wished in the zone).
- Automatic or manual operation.
- “Echo” Mode.
- Temperature schedule programming
- Setting of the zone operation mode (COLD, HEAT). * *
Note: This mode does not change the mode of the AC unit. It only affects the demand of temperature of the zone.
Selection of the temperature units
The OneZone thermostat allows the user to select the temperature units. The default is degrees Fahrenheit and the
user can change it to Celsius as follows:
1.- With the thermostat set to OFF, touch and hold
on the Airzone icon until the display shows all the
icons.
2.- The temperature appears on the screen. Touch
and hold on the Airzone icon, until the first setup
screen appears.

7
3.- Cycle with the arrow keys until the units setting
appears in the screen.
4.- Touch on the units display. These will begin to
flash
5,- Select the units type (°F or °C).
6.- Confirm the selection with a touch on the Airzone
icon
7.- To exit configuration mode, touch the ON / OFF.
The thermostat will be turned off.
OneZone operation modes
The operation mode establishes how the OneZone system is going to work, wheather in COLD or HEAT. The
operation mode will not modify the AC unit mode, but it must be the same, to be able to reach the comfort
temperature. The operation modes that can be selected are:
• COLD
In this operation mode, the system works as the cold mode of the AC unit. There will be demand
(the damper will remain open) whenever Tsetpoint < Tambient.
• HEAT
In this operation mode, the system works as the heat mode of the AC unit. There will be
demand (the damper will remain open) whenever Tsetpoint > Tambient
Thermostat Utilization
The thermostat can work in MANUAL or AUTOMATIC mode, following a time programming schedule.
MANUAL Operation.
The MANUAL operation is indicated by the icon: and allows to activate/ deactivate the air conditioning of the
zone where the thermostat is installed and to define the comfort set point temperature for this zone. The
activation/deactivation of the air conditioning is performed by pressing the icon ON/OFF.

8
The comfort temperature selection will be set with the selection arrows: and The temperatura range is
from 65 to 85°F in 1°F steps.
Additional functionalities of the OneZone thermostat
The OneZone thermostat has additional capacities that contribute to the energy efficiency and individual comfort,
like the functions ECHO and timed schedule programming. A detailed description of how to use these functions are
available in our web page www.airzoneusa.com/onezone/manual.
ECO Functionality Activation
The ECO function is activated and deactivateed by directly pressing on the ECO icon. .
When ECO mode is activated, the set point temperatura will be shifted by 1ºF every 30 minutes, with a maximum
shift of 4ºF. This shift, increases the set point temperature, if the operation mode is COLD, or decreases the set
point temperature, if the operation mode of the system is HEAT.
Time Scheduled Program Activation
The automatic mode operation is indicated with the icon:
The change between MANUAL and AUTOMATIC mode is made by touching the icons: or . Depending on
the active icon at a given time, it will appear the options at that time. When the one that is wished is selected, this
one will begin to blink.
The OneZone thermostat allows to set time scheduled programs (Start Time, end time and temperature set point in
that time slot), allowing up to 3 separate programs for each day of the week, group of days (weekdays and
weekends) and full week.
Setup and modification of the Day and hour
* Before making any time schedule programming,it is required to set the thermostat clock.
Shift direction
Maximum shift
Shift rate
COOL mode
Increases the set point
4°F (2°C)
1°F (0.5°C)/30 min.
HEAT mode
Reduces the set point
4°F (2°C)
1°F (0.5°C)/30 min.
ON/OFF Icon

9
1.- To enter the time setting mode, press and hold on the time display until the day of the week appears blinking.
2.- Select the day of the week with the arrows. Sunday is number
1
3.- Confirm the selection with a short touch in the Airzone icon
4.- The hour digits will start blinking
5.- Select the hour with the arrows. Hours
are in 24Hrs format.
6.- Confirm the selection with a short
touch in the Airzone icon
7.- The minute digits will start blinking
8.- Select the minutes with the arrows.
9.- Confirm the selection with a short
touch in the Airzone icon
Batteries replacement
When the LOW BATTERY icon appears on the thermostat screen indicates that the thermostat batteries are at the
end of their life span, and must be replaced.
--:--

--:--

::
::

::

:

::
--:----:--
:--:--
:--:--
::
::
::
LOW BATTERY

10
Thermostat battery replacement
To replace the batteries, insert a coin into the slot on the bottom of the thermostat and turn it 45 ° to separate the
thermostat from the base.
Once separated the touch screen, replace the batteries housed inside maintaining the same polarity (2 AAA
batteries 1.5V). Reassemble both parts to snap back to its original position.
1.- Separate the thermostat from the base with a coin
2.- Remove the exhausted batteries
3.-Insert the new bateries
Replacement of the damper control module batteries
When the batteries are reaching the end of its useful life for the damper, a red LED, next to the infrared sensor will
begin to flash. When this happens, it is time to change the batteries..
You'll need to remove the grille as you did to install the damper and access control module box.
Remove the battery holder box from the damper.
1- Open the lid, separating the latches.
2.- Remove the batteries