AIS OXYGEN 120 User manual

12345
OXYGEN 120 INSTALLATION
1
P-INSTRUCTOX120 Revision 11/20/2017

12345
OXYGEN 120 INSTALLATION
2
Hardware List
Flat head wood screw #9 x 7/8 long with #2 Phillips drive, silver
Used to attach surfaces and end panels
Hex set screw ½-13 x 2” long with 1/4” hex drive, black
Used on Legs
Hex cap machine screw ¼-20 x 5/8” long with 3/16” hex drive, black
Used on spine beam mounts and cable trays
Hex cap machine screw ¼-20 x 2 3/4” long with 3/16” hex drive, black
Used on rails and legs
Hex set screw ¼-28 x 1/4” long with 1/8” hex drive, silver
Used on spine screens
Pan head machine screw 10-24 x 5/8” long thread cutting tip with #2 Phillips
drive, silver. Used to attach outlets.
Pan head machine screw 8-32 x 3/8” long thread rolling tip with #2 Phillips
drive, silver. Used to assemble electrical covers.
Pan head machine screw 10-32 x 1/2” long with #2 Phillips drive, silver.
Used on spine screens to attach base support brackets.
Flat head machine screw 10-32 x 1/2” long with #2 Phillips drive, silver.
Used on territory screens to attach base support brackets.
Pan head machine screw 8-32 x 1/4” long with #2 Phillips drive, silver.
Used with acorn nuts to attach powerpole.
Acorn nut 8-32 x 5/16” long, silver.
Used with 8-32 x ¼” long screws to attach powerpole.
Pan head drill point sheet metal screw #8 x 3/8ths” long with #2 Phillips
drive, silver. Used to attach Side Mount screens to hanging brackets
and endcap worksurface cantilevers to legs.
Flat head sheet metal screw #8 x 2” long with #2 Phillips
drive, silver. Used to mount Endcap Hutch to base.
Flat head sheet metal screw #10 x 3/4” long with #2 Phillips
drive, silver. Used to mount items to laminate storage cabinets.
Flat head self drilling screw #10 x 3/4” long with #2 Phillips
drive, stainless steel. Used to mount screens.
P-INSTRUCTOX120 Revision 11/20/2017 2

12345
OXYGEN 120 INSTALLATION
3
Revision Log
Date
Page No.
Description of change
Name
11/20/17 1-43 Originated S. Powers
P-INSTRUCTOX120 Revision 11/20/2017 3

12345
OXYGEN 120 INSTALLATION
4
End Leg Assembly
Straight LegAssembly
¼-20 x 2.75L
hex cap screw and nut
6 places. Tighten fully.
Note: Place screw heads
on OUTSIDE of bench.
¼-20 x 5/8”L hex cap
screw
2 places. Leave loose.
Spine Beam Mount
Rail Mount
Twist Plate
Leg Horizontal
½-13 x 2”L Set Screw.
2 places.
Insert leg to stops
Note: Tighten set screw
until metal “forks” are
spread outward into tube
sides. Joint should have
no movement.
P-INSTRUCTOX120 Revision 11/20/2017

12345
OXYGEN 120 INSTALLATION
5
Shared Leg Assembly
End Leg Assembly
(See page 4)
Shared Leg Assembly
Mirror parts on End
Leg Assembly
Note: Use the same ¼-20 x
2.75L Hex Cap Bolt and
Nut to hold on both parts.
P-INSTRUCTOX120 Revision 11/20/2017