Alberici HIRA ONE User manual

1
Operator’s manual
Rev. 1.06
Hira One
Money Changer
Operator
’s
Manual
SaXXot Deutschland GmbH
Zeppelinstrasse 71, DE 81669 München
Telefon: [phone] - Telefax: [phone]
E-Mail: [email protected] - Internet: www.SaXXot.de
www.saxxot.de

2
This manual has been prepared with the utmost care. Nevertheless, it is not
possible to assure at any time the exact correspondence of the descriptions to the product features.
The manufacturer shall not be held liable by the User for any damage, losses, or third party
claims arising from any uses of the manual or of the product .
NOTA
www.saxxot.de

3
SOMMARIO
1. Package content............................................................................................................................4
2. Component names........................................................................................................................4
3. Product description ......................................................................................................................5
4. Warning........................................................................................................................................5
5. Installation....................................................................................................................................6
6. Operation......................................................................................................................................8
7. System configuration ...................................................................................................................8
8. Messages....................................................................................................................................18
9. Cleaning the Note Validator ......................................................................................................20
11. Disposal of the product..............................................................................................................21
12. Terms of Guarantee...................................................................................................................21
13. Customer Service.......................................................................................................................21
STORICO REVISIONI
Revisione n°
Data
Modifica
Note
Creazione 27.12.12 Creazione Scheda CMS
Rev. 1.01 23.09.14 Nuovo Design
Rev. 1.02 10.01.14 Sostituito BillyOne a Taiko
Rev. 1.03 08.10.14 Abilit./Disabil. Reset Credito Residuo FW v. 1.14
Rev. 1.04 18.02.15 Funzioni abilitazione/disabilitazione e
erogazione via GSM. FW v. 1.16
Rev. 1.05 10.03.15 Aumentato timeout visualizzazione
valore svuotato. Inserito 1’ Timeout di
uscita in menu svuotamento
FW v. 1.18
Rev. 1.06 27.06.15 Abbassato timeout cancellazione
automatica credito residuo FW v. 1.19
www.saxxot.de

4
Dear Customer,
we would like to thank you and congratulate for your choice. We trust that you will appreciate the
quality and performace of the HIRA ONE automatic Change Machine.
This machine operates by cctalk protocol, the well-established serial communication mode that
provides security and precision.
1. Package content
The package contains:
1. HIRA ONE Change machine
2. 2 pairs of keys
3. the power cable (see inside of money box)
4. the instruction manual (this manual)
This product has been packed with the utmost care. In the case that you receive it damaged or
incomplete, please notify immediately your findings to the Carrier.
2. Component names
POS. COD. DESCRIZIONE
A AE-0806 PS Power Supply Box
B SH-1A21 ChangeOne board CMS
C LED-0101 Blue 3-led bar
D HP-Z114 oppure:
K-02C-040023
HopperOne S11 ccTalk STD (HIRA One)
Or else:
Hopper AH4 Discrim. ccTalk (HIRA AH4)
E AA-0309 Estensione di capacità SECTOR 100
F LB-LC1 oppure:
LB-MC02
Note validator BillyOne ccTalk
Or else:
Note validator OryOne ccTalk
G PL-MK21-ET6H Halo square 21 RGB illuminated pushbutton
H AM-1509 Flat key lock keyed different, L=21mm
I AM-1305 or else:
HR1-011A-P00
Plastic Coinbox “A”
Or else, in version with Coin Acceptor:
Metal Coinbox
(L) GE-66SC +
IM-N000-0L10 AL66S coin acceptor (only with BillyOne) + PP coin entry bracket
A
(L)
B
E
C
D
F
G
H
I
Please read carefully this handbook, to obtain the most from your machine.
www.saxxot.de

5
3. Product description
3.1 General data
Technical specs HIRA ONE
Size max:
Size with floorstand:
Weight:
Voltage:
Nominal power:
Operation temperature:
Installation:
Coin capacity:
Components:
Power supply unit
Control board
Note validator
Pay-out Hopper
Coin acceptor (optional)
Remote audit (optional)
283 mm (l) x 460 mm (h) x 367 mm (p)
283 mm (l) x 1410 mm (h) x 367 mm (p) [floorstand 275 (l) x 950 (h) x 367 (p)]
24,5 Kg - 43 Kg with floorstand
230 Vac - 50 Hz
140 W max
0°C ÷ +50°C
Indoor - on desktop, or on floorstand, or wall-mount
HIRA ONE (S11): 2000 (0,50 o 1 €), 1800 (2 €)
HIRA D (AH4): 1800 (mixed denominations)
Power switching 340W
CHANGEONE CMS with DISPLAY LCD 2x16
BILLYONE, or: ORYONE (con impilatore)
HopperOne S11 (HIRA ONE), or: HOPPER AH4 (HIRA D)
AL66S cctalk (N.B.: not with OryOne)
GSM-GPRS or GPS/GSM/GPRS (*)
Notice: Euro is the preset currency. If you require a different currency, please request your
currency before placing your order.
(*) The system requires a SIM card enabled for data traffic, and the subscription to the Portal ARGO if you want to
control the machine via the Internet, or a SIM card enabled voice traffic / messages and data traffic if you only want to
use SMS messaging. It is recommended to check carefully that the SIM card functions properly in the area.
3.2 Available functions
- Change of notes (and coins) into coins or tokens, delivers 1 denomination (Hopper S11*)
- Change of notes (and coins) into coins, delivers 3 denomination (Hopper AH4*)
- Purchase of tokens with or without Bonus prize (HIRA ONE)
- Control of accounts via display (by board keys)
- Programmable via menu (by on-board board keys)
- Display language change (“SEL” button before inserting money)
4. Warning
-Comply with the instructions in this manual
- Switch power off before any maintenance operation
- Use only within the recommended temperature/humidity range
- Do not expose the machine (and especially the mote acceptor front plate) to direct
sun light or to incandescent light (> 3000 Lux)
- When in precence of car exhaust gas or smoke, clean and check the components (the note acceptor
in particular) regularly and frequently.
- Do not favour contact with dusts or chemical moisture or sprays, water or other liquids
- Instal indoor
- Wipe clean by a dry piece of cloth (or slightly wet with alcohol)
- Do not use thinners or organic solvents
- The note acceptor could reject (or get jammed by) stained notes, or worn out, wet, wrinkled, torn,
dog-eared, oil-smeared, with sticking tape or similarly affected.
(*) Tokens or coins with very irregular shape are not accepted
!
www.saxxot.de

6
5. Installation
PAY ATTENTION: IT IS ESSENTIAL TO FASTEN THE MACHINE TO A
SOLID WALL BY USING EXPANSION BOLTS
USE OF THE WALL SLAB (code nr. HR1-013A-V06) is recommended.
Put the Change Machine in place and fasten it to the wall by
fitting expansion bolts through the rear side 4 “x” holes.
The large holes at the foot allow to secure the machine by
a binding chain.
The wall fixing slab HR1-013A-V06 makes installation
extremely easy (see drawings in the next page).
Once fastened the slab to the wall, the unit can be hung
to the 4 set hooks, and then fixed through the 2 “z” holes.
All measures in mm
X
Z
X
Z
X
X
275
27,5
27,5
100
120
68
60
68
80
!
www.saxxot.de

7
WALL-MOUNT SLAB:
PREPARATION FOR USE:
PAY ATTENTION:FILL THE HOPPERS ONLY
WHEN THE MACHINE IS OFF.
Open the door and locate extensions capacity on top of the hopper.
Unlock the latch A (white slide) of the cover and slide
the latter fully out towards the outside, until is positioned as
a pilot chute: pour into the hopper the coins or tokens to be
dispensed as change.
Unlock again the latch A and slide the cover back
to “closed” position.
Close the tiltable front flap of the machine.
Plug the power cable in, and turn the main switch on.
Component check and self-setting shall start automatically. At the end, a message will inform that
the machine is ready for operation, showing what coin (or token) value will be paid in exchange for
notes and coins introduced, as well as a welcome wording.
This message takes shifts with:
As soon as the control board enables the note acceptor, the latter’s front slot flashes once in blue
colour for each enabled note, or once in red for each disabled note. For instance, if the 5, 10, 20
Euro notes are enabled, and the 50 and 100 Euro notes are disabled, the front slot will flash 3 times
in blue colour and 2 (twice) in red.
The machine is now ready to operate.
300
12
0
45
8
0
120
40
40
60
180
470
70
45
50
Φ
12
45
X
Prepare the tunnel for the
power cable in the wall
(correspon ing to “Y”
Hole in the slab).
Fasten the slab to the
wall by stur y expansion
bolts, through the 6
“X” (Φ 12 mm) holes.
Connect the cable to its socket behin
the machine, an hang the latter on the
4 “W” supporting hooks.
Fix the unit to the slab by M8 screws
through the two “Z” threa e holes -
unless you mean to often remove an
re-hang the machine up, by the four
“w” hooks
.
Y
W
Z
14
0
14
0
Z
X
X
X
X
X
22
0
40
EROGA MONETE DA
2,00 €
CHANGEONE
Promo
A
www.saxxot.de

8
6. Operation
Two buttons are available: “OK” and “SEL”. The latter allows the user to choose the language he
wants on the display (English, French, German, Italian and Dutch are available. Ask before placing
order for other languages options). This type of operation varies depending on whether the
operation mode is set to AUTOMATIC or to MANUAL.
AUTOMATIC MODE - when a note or coin is inserted, the credited amount is displayed, and the
control board starts the pay-out by the hopper.
MANUAL MODE - when a note or coin is inserted (or when the value of one token is reached), the
OK button will lit up green . Press the button to receive change coins (tokens). If the machine is set
to Tokens with Bonus, it will be possible to choose what Bonus level must be reached before
getting the tokens. Introduce money until the searched amount is reached, then press the OK button.
WARNING: If there are not enough coins in the hopper to fulfil the whole exchange request, the remaining credit shall
be displayed and retained in memory. Switch off the machine, fill the hoppers, and switch on again: the remaining
credit shall be paid out.
An option is to set the Remaining Credit Menu (see section 7.3.14) so as to cancel the remaining credit - and
at the same time record it in the Accounts menu - by switching the machine off and on again.
7. System configuration
7.1 Default setup
This Money-Change machine is preset by default as follows (unless requested for different setup):
Control Board Parametres Pay-out mode = AUTOMATIC
Bonus = DISABLED
Level sensors = DISABLED
Hopper S11 Parameters Hopper nr. 1 € 2.00 = ENABLED
Hopper AH4 discriminator [ccTalk] Preset by default to 0,50 – 1,00 – 2,00 €
BILLYONE Validator [ccTalk] Parameters € 5.00 - …. - € 100.00 = ENABLED
AL66 S [ccTalk]coin acceptor Parameters € 0.05 - € 0.10- € 0.20 = DISABLED
€ 0.50 - € 1.00 - € 2.00 = ENABLED
7.2 Restore default configuration
If any variation is made, it will be possible to restore the default configuration as follows:
enter the initial menu, scroll by UP and DOWN keys and choose RESTORE DEFAULT CONFIGURATION
then press OK; the message DEFAULT CONFIG.RESTORED will be displayed.
NOTICE: the RESTORE DEFAULT CONFIGURATION command resets the default PIN code (0000) .
www.saxxot.de

9
7.3 Menu functions
7.3.1 Surf the Menu:
To enter the menu and navigate it, make use of the 3 keys located on the board rear side.
Get access to the menu by holding the three buttons pressed at the same time for 5 seconds.
POWER IN
COIN ACCEPTOR AL66
NOTE ACCEPTOR
HOPPERONE S11
ILLUMINATED PUSHBUTTONS: RGB1 = OK RGB2 = Language select
PROG
+
+
+
-
-
-
OK
PWR
IN
PWR
OUT
CCT
24
TST
PT
STP
RGB3
RGB2
P4/7
SP1
RGB1
CC12
REG
24 12 GND
CMS board
Rear view
OK
confirm
selection
+ - navigate menu UP and DOWN; modify figures and letters
REG adjust display brightness
CCT 24
PWR IN
CC12
24 12 GND
RGB1
RGB2
RGB3
PWR OUT
www.saxxot.de

10
7.3.2 MENU MAIN STRUCTURE
RESTORE DEFAULT
CONFIGURATION
MODIFY PIN
(*) only available with HopperOne,
and only if preset for:
DISPENSING MODE =TOKENS
EXIT
MENU
PROMO
LANGUAGE
SETUP
BONUS
Notice: PIN is requested
to access some sub-menu
settings.
(*)
MANUAL REFILL
SETUP
ENABLE./DISABLE
REMAINING CREDIT
CHANGEONE
Promo
EXIT
MENU
SHOW
PERIPHERAL UNITS
SHOW
ACCOUNTS
RESET
ACCOUNTS
PERIPHERAL
UNITS SET UP
EMPTY OUT
HOPPER
www.saxxot.de

11
7.3.3 Show peripheral units
This menu allows to check the state of the PERIPHERAL UNITS,for instance:
ecc. ecc.
7.3.4 Show accounts
This menu allows to check the total and the partial values of cashed and paid amounts.
Questo menu permette di leggere i totali e i parziali dell’incassato, dell’erogato, dei crediti agati
- Press OK: the display will show the total amounts introduced (TOTAL IN). Press UP, and OK if
you want to exit the ACCOUNTS menu.
- Or else, press DOWN to check the total amounts dispensed (TOTAL OUT).
- Press DOWN to go on browsing the submenu.
Notice: whenever the Partial Amounts record get cancelled (see section 7.3.5), the previous value recorded in “Last
Partials cancelled” gets replaced by the amount that has just been reset.
LAST AMOUNT DISPENSED: when the board is in stand-by condition, it is possible to check the last amount
dispensed, by holding the SELECT pushbutton for full 4”.
7.3.5 Reset accounts
To use this sub-menu it is necessary to digit the PIN code. This function allows to cancel the
account records (both paid out and cashed in) of the machine.
COIN ACCEPTOR
DISCONNECTED NOTE VALIDATOR
CONNECTED
HOPPER 1
EMPTY
Exit
Total in
00,00 €
Cashless Total
00,00 €
SHOW
ACCOUNTS
RESET
ACCOUNTS
Total out
00,00 €
Partials in
00,00 €
Partials out
00,00 €
Remained Credit
Paid 00,00 €
(*) Reset of the remaining credit: see section 7.3.14
Last partials
cancelled
IN: 00,00 €
OUT: 00,00 €
(*)
Exit
RESET
ACCOUNTS
Reset
Total Amounts Reset
Partial Amounts
Enter PIN
0
For each of the 4 digits of
thePIN, use UP and DOWN to
highlight the figure wanted, then
confirm by OK. At the end, the
display will show:
All Totals
cancelled
All Partials
cancelled
Exit
Once entered the PIN,
the display will show:
(*) Whenever the Partial Amounts record get cancelled (see
section 5.4), the previous value recorded in “Last Partials
cancelled” gets replaced by the amount that has just been reset.
(*)
www.saxxot.de

12
7.3.6 Setting up the peripheral units
This menu allows to set up the denominations accepted by the note validator and by the coin
acceptor, as well as the value of the coins/tokens dispensed. It also permits to set the change mode
as either automatic or manual, and to enable/disable the full/void sensors of the hoppers.
7.3.6.1 NOTE VALIDATOR SETUP
The board automatically detects the presence of the note acceptor during initial check. All the
programmed note values (5-to-100 Euro) get automatically enabled. To modify this default
condition, press OK to get to the first option (ex. 5 €) and highlight it, then press UP or DOWN to
reverse its state. Press OK to shift to the next option (ex. 10 €).
Set up
Note validator
Set up
Coin acceptor
PERIPHERAL UNITS
SETUP
EMPTY OUT
HOPPERS
< 5 > 10 20 50 100
OK OK OK OK OK
5 < 10 > 20 50 100
OK OK OK OK OK
5 10 < 20 > 50 100
OK OK OK OK OK
< 5 > 10 20 50 100
NO OK OK OK OK
< 2,00 > 1,00 0,50
OK OK OK
< 2,00 > 1,00 0,50
NO OK OK
2,00 < 1,00 > 0,50
OK OK OK
2,00 1,00 < 0,50 >
OK NO OK
Set up
Dispense mode
Level sensors
enabled
Level sensors
disabled
Set up
COINS
Set up
TOKENS
Set up Hopper 1 :
1,00 €
(*)
Press Down or Up
to modify amounts in
discreet steps of 0,05
€ each
Dispensing mode
AUTOMATIC
(*)
Dispensing mode
MANUAL
5 < 10 > 20 50 100
NO OK OK OK OK
2,00 < 1,00> 0,50
NO OK OK
Exit
Set up
GSM / GPRS
Set up
Note validator
< 5 > 10 20 50 100
OK OK OK OK OK
<
5 > 10 20 50 100
NO OK OK OK OK
5 < 10 > 20 50 100
OK OK OK OK OK
5 10 < 20 > 50 100
OK OK OK OK OK
www.saxxot.de

13
7.3.6.2 COIN SELECTOR SETUP
The board automatically detects the presence of the coin selector during initial check. Among the
accepted coins (0.05-to-2 €), the following ones get enabled by default: 0.50 € - 1.00 € - 2.00 €.
To modify this condition, press OK to get to the first option (ex. 2 €) and highlight it, then press UP
or DOWN to reverse its state. Press OK to shift to the next option (ex. 1 €).
7.3.6.3 DISPENSING MODE SETUP
Allows to choose whether to dispense COINS or TOKENS or TOKENS+CHANGE, and whether the
DISPENSING MODE will be AUTOMATIC or MANUAL.
It also permits to monitor the level of the coins in the hopper(s) by the electronic sensors.
NOTICE: monitoring of level sensors is disabled by default. This means that the board does not know when the hopper
is empty, so it will send the pay-out command even if there are no coins available. When the hopper runs out of coins
during dispensing or at the end of payment, no warning will be displayed. If the empty state is detected when powering
the unit, this one shall not accept any money.
If instead the monitoring has been enabled, and there are not enough coins in the hopper, the display will warn that the
hopper is empty. There will usually remain 20 coins approximately, so as to complete the change payout.
PLEASE NOTICE: if the machine must be re-configured from token (or token+backchange) dispenser to coin
changer, always do reset to DEFAULT CONFIGURATION and RESET ACCOUNTS. Else, the bonus setting could
produce Accounts inconsistency.
Set up
Coin acceptor < 2,00 > 1,00 0,50
OK OK OK < 2,00 > 1,00 0,50
NO OK OK
2,00 < 1,00 > 0,50
OK OK OK 2,00 1,00 < 0,50 > OK NO OK
SET UP
DISPENSING MODE Set up
COINS
Level sensors
enabled Level sensors disabled
Set up
TOKENS
Set up Hopper 1:
1,00 €
(*) Use keys
Down and Up to
modify values
(*)
Dispense mode
AUTOMATIC
Dispense mode
MANUAL
www.saxxot.de

14
7.3.6.4 SET UP GSM/GPRS
When the GSM/GPRS kit is installed, it gets detected during self-configuration, and its parameters
must be set up for operation.
(*) Used only for Argo Web Portal. By buttons + and - , locate the letter/digit, and OK button to confirm your choice; the cursor will
automatically move to the next character. There are 16 characters in the machine name, and 10 for the User Code.
After confirming the last character, the name you have typed gets automatically saved.
See other notes next page!
Set up
GSM/GPRS
Set
Name of Machine
Set enabled
Cellphone Nrs.
Test GSM / GPRS
Module
Exit
Insert Name:
A
Cellphone Nr [1]:
>_<
Insert name:
LUCKY HALL
Cellphone Nr [1]:
>+39347nnnnnnn<
Cellphone Nr [2]:
>_<
Cellphone Nr [4]:
>_<
GSM / GPRS Module
Test in progress
GSM / GPRS Module
In service
(*)
(**
)
Please wait …….
Please wait
…….
Please wait
…….
Set
User Code
Insert User Code:
A
Insert User Code:
Pleaseloginme
Enable/Disable
Service status
Service status
Enabled
Service status
Disabled
Enable/Disable
Remote payment
Remote payment
Enabled
Remote payment
Disabled
Set
Security level
Security level
Low?
Security level
High?
Please wait… saving
(***)
(***)
(****
www.saxxot.de

15
(**) By buttons + and - , locate the number you want to write, and press OK to confirm it; the cursor will automatically move to the
next character. Once confirming the last digit, also confirm the whole number entered: it is proposed to enter the second number,
and finally the third.
(***) When the Service Status Remote Enable function is active, the machine can be put out of service by sending an SMS (text is
“CMD=OFF”) from any of the 3 enabled cellular phones. To restore service, send text “CMD=ON”.
(****)When the Remote Pament function is active, and the Security Level has been set to Low, it is possible to command the machine
to dispense an amount (in €) or a number of tokens (pieces) by sending the following sms text from any of the 3 enabled cellular
phones:“OUT=n°” (n° = any value between 0 and 250).
When the Remote Pament function is active, and the Security Level has been set to High, it is possible to command the machine to
dispense an amount (in €) or a number of tokens (pieces) by sending the following sms text from any of the 3 enabled cellular
phones:“OUT=n°:1234” (n° = any value between 0 and 250; 1234 = any combination of figures except 0). In this case, the display
will show the password chosen: the User will put the Refill key in the Refill lock (or the RFID key in its reader), and then enter the
password by using the buttons SEL (select each number) and OK (confirm each number).
7.3.7 Empty out the Hoppers
Use this function to make the selected hopper pay out all the contained coins / tokens. Once emptied
the first hopper, total dispensed amount shall be displayed. Press OK to go on with second hopper.
7.3.8 Restore default configuration
To use this sub-menu it is necessary to digit the PIN code.
WARNING: in case of reset, the system sets back to default configuration. The PIN code will be
reset to the default 0000 setting. Account records shall not be cancelled.
Exit
EMPTY OUT
HOPPERS
EMPTY
HOPPER 1
total
nnn,nn €
EMPTY
HOPPER 2
total
nnn,nn €
RESTORE DEFAULT
CONFIGURATION
Enter PIN
0…
DEFAULT CONFIG.
RESTORED
This message will briefly appear after the
PIN has been entered, then the message
DEFAULT CONFIGURATION RESTORED will
be shown again.
www.saxxot.de

16
7.3.9 Bonus Set Up
This function will operate only if at least the hopper nr. 1 is preset for paying tokens. Take care to
set up all hoppers parameters. Bonus function is disabled by default.
7.3.10 Language setup
7.3.11 Promo
It is possible to preset an advertisment on the display. Press OK:
Press again OK, the pointer will highlight the first digit: by UP or DOWN, choose the character that
you want to insert, then confirm by OK. The pointer will highlight the following digit.
Once digit nr. 16 has been confirmed, the message gets stored.
7.3.12 Modify PIN
The PIN code allows to get access to the discretional menus of the system.
The PIN code is made up by 4 figures (each of them from 0 to 9: 10,000 combinations available).
If the entered PIN is not correct, the User is given another 4 tries before the board gets blocked-up
by its security interlock. The system can be started again by switching it off and on again.
ATTENTION: the default PIN code is 0000
The settings in the following menus can be modified by using the PIN code:
MODIFY PIN - RESET ACCOUNTS - RESTORE DEFAULT CONFIGURATION
BONUS Bonus
ENABLE?
Bonus
DISABLE?
LEV EURO PCS
0 1€ 1 LEV EURO PCS
1 1€ 1
(*)Use Up key to modify
values
Bonus settings
stored
LEV EURO PCS
1 2..3..10 € 1
LEV EURO PCS
1 10€ 1
LEV EURO PCS
1 10€ 11
(*)
(*)
LEV EURO PCS
2 10€ 11 LEV EURO PCS 2 10€ 11 LEV EURO PCS 1 11..12.. € 1
NOTICE: in case of
any
mistake, do confirm the
wrong programmed data,
then re-program correctly.
LANGUAGE
SETUP Seleziona lingua ITALIANO Choose language ENGLISH Waehlen Ihre Sprache DEUTSCH
Digit text
------------------------
www.saxxot.de

17
To modify the existing PIN, press OK, and digit the old PIN code: to digit each code figure, first
use keys UP and DOWN to set each figure, then confirm it by OK. Once the 4th figure has been
confirmed, confirm by OK the whole old PIN:
To enter the new PIN code, use first the UP and DOWN keys to set each figure, then confirm it by
OK. Once the 4th figure has been confirmed, confirm by OK the whole new PIN.
As every single figure gets confirmed, an asterisk takes its place, so preserving secrecy.
NOTICE: when DEFAULT CONFIGURATION is restored, the PIN code gets reset to 0000.
7.3.13 Manual Refill Set Up
Refill can take place when unit is empty or not. Allows to record the amount put in.
MANUAL REFILL
SET UP
E
M
P
T
Y
H
O
P
P
E
R
S
MANUAL REFILL
Confirm?....
Enter filled
Amount: 1€
Totale importo
Caricato: 2500€
Warn at 1
Euro available
MANUAL REFILL
SET UP
MANUAL REFILL
Confirm?....
Total € / Pcs
available: 1€
H
O
P
P
E
R
S
N
O
T
E
M
P
T
Y
(*) Shows “€” when set
for coins
Shows “Pieces” when
set for tokens
(*)
+ /
-
+ /
-
Totale € / Pcs
available: 1800€
Warn at 50
€ / Pcs available
+ /
-
+ /
-
Warn at 100
Euro available
Warn at 200
€ / Pcs available
New PIN
0
Enter PIN
0
MODIFY PIN
www.saxxot.de

18
7.3.14 Enable / Disable remaining Credit
Amount of remaining (i.e. unpaid) credit can be reset when machine is switched off. Such amount
gets automatically recorded in the Accounts (sez. 7.3.4).
7.3.13 Exit Menu
Press OK to go back to stand-by condition:
8. Messages
8.1 Messages on the display
8.1.1 Faulty operation:
The following warning:
is accompanied by the system check. For instance, the following sliding warnings:
stand for:
the coin acceptor is not connected,
there is a fault in the note validator,
hopper 1 is properly working
The following error messages can possibly appear:
the mentioned peripheral unit (coin acceptor, or note validator,
or Hopper, a.s.o.) is connected and functioning
the mentioned peripheral unit has been disconnected
the mentioned peripheral unit is connected but faulty
the Hopper is empty
the inserted note is not enabled
The message
EXIT MENU
Exit Menu
in progress…
CHANGEONE
Promo
CHANGEONE
OUT OF SERVICE
...COIN ACCEPTOR…
.. DISCONNECTED ...
R N° 1… …. HOPPE
TED …. … EMPT
PTOR …. …. NOT
CTED … .… IN ER
TOR… …. HOPPE
ROR …. … CONN
(PERIPH.UNIT)
CONNECTED
(PERIPH.UNIT)
DISCONNECTED
(PERIPH.UNIT)
IN ERROR
HOPPER
EMPTY
BANKNOTE
DISABLED
Remaining Credit
1 €
means that coins have run out during the payout.
Switch power off, fill it up, and switch power on again:
the board will prompt the hopper to complete the payout.
ENABLE / DISABLE
REM. CR. RESET
Reset of Remaining Cr.
TURN OFF / ON + / -
Reset of Remaining Cr.
DELAYED
Reset of Remaining Cr.
DISABLED
+ / - + / -
(*) When enabling this option, the remaining credit shall be cancelled within 15 seconds from end of transaction.
(*)
www.saxxot.de

19
8.2 Messages from the Note validator
8.2.1 BillyOne / OryOne Validator
During operation, the amount of consecutive red flashes produced by the entry slot indicates the
possible malfunctions (see chart below):
8.2.2 Front bezel flashing blue
When the front bezel flashes blue, it means that either the stacker has been removed, or the
detection sensor has gone faulty.
8.2.3 Fraud-fishing protection
The banknote reader is equipped with a security device that gets activated in the event of fishing
fraud attempts repeated over a period of time.
This device can be set through the dip-switch SW2 (DS-row on the Validator side) to operate in a
"soft" mode (* DS2 = ON) or in "extended" mode (** DS2 = OFF).
(*) Dip-Switch SW2 ON
Any attempt
at “fishing” will cause the note to be rejected, without showing any visible
signal.
(**) Dip-Switch SW2 OFF
Attempt Validator reaction Do as described below
1
th
Remains in service -
2
th
Remains in service -
3
th
> error (3 red flashes) Reset (switch off then on)
4
th
> error (3 red flashes) Reset (switch off then on)
After the 5th fraud attempt (3 yellow flashes), it is necessary to wait for automatic restore
of service. Take care not to switch the device off.
NOTICE: no error status will be transmitted to the machine, so that the latter does not go out of
service, and will therefore continue to maintain the other functions working.
nr of red flashes Description
1 Validator is open
2 Jammed banknote
3 Fraud attempt detected
5 Adjust optic sensors
7 Stacker full (OryOne Only)
9 Low power supply
11 Check operation of the encoder + efficiency of the validator motor
12 Check operation of the encoder + efficiency of the stacker motor
(OryOne only)
14 ROM error
www.saxxot.de

20
9. Cleaning the Note Validator
9.1 Manual cleaning
The ability of acceptance may decrease due to the accumulation of dust and cellulose dust released
by banknotes during transit, or because of residues or sprays, which may spread on the detecting
sensors and on transmission parts.
It is therefore recommended to clean these parts at least monthly, as indicated below.
1. Turn power off and unplug the cable
from the 10-pin connector interface.
Press the yellow button C, located
under the reader, to release the main body
from the faceplate, and slide it backwards.
2. Move the D button upward, hold it while sliding the cover backwards; then lift the latter up
and rotate it 180° to the right side.
3. Gently wipe the sensors with a clean, lint-free tissue, or with a cotton swab, or with a small
sponge, possibly moistened with isopropyl alcohol.
4. Completely remove the dust and residues from the 4 silicone rollers, and from the 4 elastic
matching wheels which are located in the lower surface of the upper lid. To remove the most
stubborn dirt from rollers and wheels, use isopropyl alcohol.
PAY ATTENTION: do not use
organic detergents (ex. alcohol,
thinners or petrol). Use only
isopropyle alcohol.
1. Sensors
2. Rollers
3. Elastic matching wheels
!
WARNING! Do switch power off
before opening the machine!
D
C
A
A
A
A
A
B
C
www.saxxot.de