Albrecht AE 4200 R User manual

CB RADIO
AE 4200 R
OPERATING MANUAL
Downloaded from www.cbradio.nl

2
Index
Important note 3
Introduction 3
Accessories included 4
Safety Precautions 4
Front view 5
Rear view 5
Installation of the radio 6
Power supply 6
Antenna connection 7
Operation 8
Switching on and adjusting volume 8
Country switch setting 8
Selecting the operating channel 9
Adjusting squelch (muting) 9
AM / FM mode switch 10
Special interest channels 11
Transmitting and correct use of microphone 12
External sockets 12
External loudspeaker 12
Microphone socket 12
Service and Warranty information 13
Technical Details 14
Service contacts 14
Legal Information 15
Albrecht Radio Passport 15
Declaration of Conformity 16

3
Important Note
Your Albrecht AE 4200 R corresponds to the latest European CB standards. As a
unique feature, our standard version has a software country switching which allows
selecting the operation mode according to the country, where you intend to use the
radio. Please make sure that you use only the country switching which is allowed in
Your country and according to your CB licence! You may risk a penalty if authority
members will find that you are operating in not allowed modes!
During first use of this radio, the radio will start in this factory preselected 40
FM / 40 AM mode:
40/40 40 channels FM / 4 Watt, 40 channels AM 4 W according to
latest European Standard EN 300 433-2, but not yet applied in
all countries. Only In Italy, Spain and Switzerland (until end of
2012) you still need a licence to operate the radio, while it is
already free of charges and licence in Belgium, Bulgaria, Croatia,
Cyprus, Germany, Estonia, Finland , France , Greece, Ireland,
Latvia, Lithuania, Monaco, the Netherlands, Poland, Portugal,
Romania, Sweden and Slovenia. The radio comes ready for the
new AM output power of 4 Watts. Depending on the date when
your country will adopt the new European power levels, it may
happen that AM is not yet allowed to use officially in certain
countries.
80/40 80 channels FM / 4 Watt, 40 channels AM / 4 W for Germany,
also for CZ (only FM) and SK (only FM 1-40 & 70-80) allowed to
use. You need no more any licence to operate the radio in this
mode, but in certain German border regions transmitting from
base stations on channels 41 to 80 in FM is not allowed (or only
with a special license).
40 FM 40 channels FM / 4 Watt (former “CEPT” settings with 40
Channels FM according to EN 300 135-2). This mode can be
used in all European countries (please see our latest issue of the
“Radio Passport”).
Please note that some countries may not allow the country switching to
German 80 channels. In June 2011, only Austria still published restrictions
for radios sold in shops within these countries.

4
Introduction
Your new Albrecht CB Radio AE 4200 R, developed and manufactured in
accordance with the latest CB regulations, offers you:
•40 channels FM / 4 watt or
•80 channels FM / 4 watt / 40 channels AM / 4 Watt or
•40 channels FM / 4 Watts / 40 channels AM /4 Watt
•Channel selection UP/ Down buttons on the radio
•Red LED channel number display
•Control LED’s for switch position (FM) and TX
•4-pin standard microphone socket, suitable also for amplifier microphones
or Packet Radio modems/TNC’s
•Socket for external loudspeaker
Please read this operating manual through carefully. This will enable you to make
use of all the functions your new CB Radio has to offer as soon as possible.
Accessories included
Your AE 4200 R comes operational with the following accessories:
•mobile mount
•2 knurled screws for the mobile mount
•2 rubber washers for the mobile mount
•fixed connected DC power cable with looped-in fuse
•spare fuse
•Electret hand-held microphone with pre-amplifier and PTT
•Microphone hanger
•various screws to fasten the radio and microphone fixing devices
•User manual with Radio Passport

5
Safety Precautions
People with pacemakers are recommended as a precaution to consult their doctor
before operating the CB radio. Not all types of pacemakers are sufficiently protected
from radiation from a nearby transmitter, so do not assume it is safe to start
operation without checking! Please remember that you are in the immediate vicinity
of a transmitting aerial, particularly when used as a mobile. If your doctor, or the
manufacturer of the pacemaker, has recommended keeping a certain safe distance
from the aerial, then please follow their instructions!
Do not transmit without connecting the aerial and never touch the aerial during
transmission!
Please also take road safety into account! CB Radio (even when only receiving,
particularly when volume is turned up) can divert your attention from the road! Road
safety is of course to be given priority! Therefore only use your AE 4200 R when the
traffic situation enables it to be used safely.
Front view
Rear view
Squelch
Receive Volume
Antenna socket
50 Ohms
External speaker
8 Ohms, min. 2 W
On / Off
LED-Channel Display
TX-FM
control LED’s
Double Function
Channel / Country switch
AM
-
FM Switch
4 pin MIC socket
12 V DC cable
outlet

6
Installation of the radio
You can either operate your ALBRECHT AE 4200 R in the car or at home as a base
station. For installation as a mobile station in the car, a mobile mount device is
enclosed. Mount the set in such a way that it is not exposed to direct sunlight if
possible, as this would lead to an increase in the temperature and can decrease the
(set’s) working life. The set should also not be installed near a heater. Mount the set
in such a way that it is exposed to as little vibration as possible.
The mobile fixing device should be attached to the dashboard, the tunnel slot or to
any other suitable place using the enclosed tapping screws. Do not install the set in a
place where it could cause injuries in the case of an accident (be careful to ensure
free leg movement). Take care not to damage any underlying wires during
installation!
Then insert the radio into the mobile mount device. Secure the set with the large
knurled screws (using the enclosed plastic washers) firmly at the required angle.
Also mount the microphone hanger using the enclosed screws in an easily-
accessible place.
In order to prevent interference to the vehicle electronics from transmission in the
vehicle, please make sure to take any mounting instructions from the vehicle
manufacturer for radios and antennas into account.
Please note: European directives allow the car manufacturers to decide, whether or
not private radio transceivers may be operated in cars, this is also valid for antenna
installations. Please install Your mobile CB station only in accordance to car
manufacturer’s installation instructions.
Power supply
Your AE 4200 R receives power from the 2 pin fixed power cable.
The red and black wires in the cable are for the power supply. The cable has a
looped-in fuse.
You can choose from two methods when connecting to the power supply (red and
black):
Example 1
The radio should be able to be switched on and off at any time using the
volume / on/off switch.
Connect up the red to the positive pole on the vehicle battery (or elsewhere
in the vehicle’s electrical system with permanent plus) or to a 12 volt power
unit.
Connect up the black wire to the negative pole on the vehicle battery or the
power unit or to a well-conductive part of the car body.

7
Example 2
The set should be automatically switched on and off with the ignition switch
of the car. The radio shall always start in last used mode on the last used
channel.
Attach the red wire to a part of the vehicle electrical system which is
interconnected to the ignition.
Connect the black wire to the negative pole on the battery or the vehicle
body.
Note for all connecting methods:
For EMC reasons, the cable used to connect to the power supply should be no
longer than 3 metres.
If you wish to operate your set at home from the mains supply then please only use
a stabilised power pack with at least 2 amps permanent current-carrying capacity.
Under no circumstances should you use a car battery charger, as these are not
stabilised and during open circuit reach such high voltage levels that your radio set
could be destroyed.
If in base station use it is important to you that the stored stations are kept even after
switching off and on again, then please do not switch the external power supply
power unit off when you switch your set off for a short time. Only use the on/off
switch on the transceiver itself.
Never repair a blown fuse with silver paper or with aluminium foil! If the fuses
keep blowing, then please give your radio set to your servicing dealer to be
repaired or hand it in to Albrecht’s service station.
The maximum allowed voltage variation for this radio is up to 15.6 volts.
Never exceed this voltage under no circumstances! The transmitting stages
for your AE 4200 R are electronically stabilised, and therefore it is impossible
to increase output by means of excessive supply voltage. Such attempts may
lead to serious damage to the radio set but will never increase output power!
Antenna connection
Connect your CB antenna to the ANT socket on the rear side of your ALBRECHT AE
4200 R. Most CB antennas must be tuned to best radiation during installation to give
highest effective communication range. CB specialists do that job with a standing
wave meter to check and adjust the aerial. Tune the antenna to the best standing
wave ratio (SWR) on an intermediate channel e.g. using Channel 1 in 80/12 mode
(26.965 MHz) or Channel 20 in all other modes.
On this channel you should obtain a SWR of approx. 1.5 or less. If the SWR
deteriorates on the highest (Channel 40) and lowest (Channel 41) channels up to a
value of 2.5, then your aerial is still acceptable. SWR above 3 is too bad for good

8
communication range. A bad SWR may also indicate that there is perhaps an
installation error or missing ground. Problems may be caused through missing
ground, especially in boats and motor homes with fiber glass body. For these cases,
Albrecht offers a special “ground less” antennas like GL 27.
Some antennas, like “Gamma II” (order No. 6725) are broadbanded and do
not need any retuning during installations.
Even if your AE 4200 R has a particularly robust transmitter high-
level stage which can even withstand mismatching of SWR=3, you
should still never transmit without an antenna!
Operation
Before switching on
•Turn SQUELCH control left as far as possible
Switching on and adjusting volume
The on/off switch is combined in the VOLUME control. To switch on:
•Turn VOLUME control from OFF position slightly right. LED display will be
illuminated. Then turn further until desired volume is reached.
Selecting the correct country code
Starting with 40 / 40 channel system
When you switch on your new CB radio for the first time, it will start with the latest
European channel setting with 40 channels FM and 40 channels in AM.
Note: this system is allowed in B, BG, CH, CY, D, E, EST, F, FIN, FL, GR, HR, I,
IRL, L, LT, LV, MC, NL , P, PL , RO, S and SLO
40/40 This position can be used in those countries, where already all 40
international channels are allowed to be used in AM and FM. AM was
traditionally used by CB from the beginning in the early 60’s in USA, and it
is still the preferred mode of all truck drivers in the world. Please use this
mode only in countries according to the list in the Radio Passport, and
please apply for an individual licence where requested. If you are not sure
whether AM with 4 Watt is already allowed, we recommend to use only
FM until the country has implemented the new rules.
If necessary You can return to this system any time later by:
•Switch the radio off
•Press Down button and keep button pressed
•Switch on the radio at the same time
•Release the button

9
Switching to 80/40 channel system (Germany and CZ/SK only)
80/40 This position is only allowed to be used in Germany and CZ / SK,
because no other European country provides the German 80 FM
channels. (Note: In Czech Republic please use only FM and in Slovak
Republic use only FM on ch 1-40 & 70-80)
No individual licence is necessary, but restrictions are still in force in
certain German border regions, where transmitting on channels 41 – 80 is
not allowed or only with a special licence.
•Switch the radio off
•Press Up button and keep button pressed
•Switch on the radio at the same time
•Release the button
Switching to 40 Channels FM
Europe-wide used 40 Channels FM mode. If you are not sure what is allowed in your
country please ask local authorities before using the radio. In case of any doubt, use
this country switching as your setting:
40 FM This is former “CEPT” mode, the programming which is allowed in most
countries. Here the radio works on the international 40 Channels in FM
mode. The Mode switch AM – FM on the front side allows only receiving
in AM and FM, but only transmitting in FM mode (residents in Italy,
Switzerland (up to end 2012), and Spain still need a licence for CB radio,
while CB radio is free for short-time travellers.)
To switch to this system
• Switch off the radio
• Press Up and Down simultaneously and keep pressed
• Switch on the radio again
• Release buttons
Please read carefully the “Radio Passport” in the last chapter of this manual
before reprogramming the unit. It is useful to take the Radio Passport with you
when travelling abroad and using 40/40 or 80/40 mode.
Note: This radio utilises a CPU system especially developed for this radio. Other
(illegal) channel systems are not stored in the CPU system and are not available at
all.
Selecting the operating channel
•with Up or Down buttons on the radio You can continuously select channels. The
present channel is displayed.
•Press the respective button longer to run up or down through the channels. The
present channel is displayed.

10
Adjusting squelch (muting)
Particularly in FM, noise can be a nuisance on a free channel. With the muting
control (SQUELCH) You can suppress this noise - but also signals which are too
weak to be received properly.
This is how to adjust the signal strength required to switch on the loudspeaker, using
the SQUELCH control knob:
The further the control knob is turned to the right, the stronger a signal has to be in
order to be audible through the loudspeaker.
In order to adjust the set to be the most sensitive to incoming signals, switch to a free
channel:
•Use the up / down switches to find a free channel, where no signal is
displayed.
•Then turn the SQUELCH control carefully to the right until the noise just
about disappears.
Now the loudspeaker stays off when on a free channel but it switches back on when
receiving even very weak signals.
The muting adjustment is particularly important during channel
scanning. In this mode the point to which the set is adjusted
decides whether scanning is stopped at the signal or not.
Therefore you should test the various muting settings for various
signal strengths and get to know this function.
AM / FM mode switch
In the German channel system 80/40 you can now receive on all 80 channels in FM
and AM, but You can transmit on all these channels only in FM.
In AM the only channels 1-40 are enabled for transmitting. If You should try to
transmit in AM on other channels, you will see an error (Er) message in the display.
Transmission on such channels is technically deactivated. A green control LED is on
during FM mode.
Special interest channels
There are a few channels which have been established for certain purposes:
Channel 1 Call channel in FM (Germany only)
Channel 9 Call and emergency channel, in Germany particularly this
channel is also used by all truck drivers in AM.
This means: a large number of stations are listening in. If
the worst comes to the worst (e.g. in case of accident etc.)
there is a good chance that someone will be listening.
To call other stations, who you know are listening in on channel 9, you can also use
this channel. Call up the desired station on channel 9. As soon as contact has been
made, agree on a free channel for your conversation and then channel 9 will be free
again for other calls.

11
An emergency channel can of course only work if as many stations as possible are
listening in. Therefore listen in to this channel as often as possible!
Channel 16 Water sport channel
Channel 19 Trucker channel on AM in France, Spain and Italy
Channel 24/25 Data transfer (Packet Radio, Germany only)
Channel 40 Calling channel in Switzerland
Some recommendations have been worked out by the CB clubs for the new
channels 41 to 80 in Germany. To find out which channels are suitable for special
purposes, please get in touch with the respective groups or check in CB magazines.
Transmitting and correct use of microphone
With the transmission button (Push To Talk) on the side of the microphone you can
switch between receiving and transmitting:
•Press PTT button to transmit.
Your radio is equipped with a TX control LED, this will light when You are
transmitting on an allowed channel in an allowed mode.
•Release PTT button again to switch back to receiving.
When the transmission PTT button is depressed, you can speak from a distance of
about 5-10 cm into the microphone. After pressing the PTT button, please wait about
½ second before You start speaking. Please remember- that different from GSM
phones- You share one channel common for transmit and receive, and Your
transmitter and the receiver(s) on the distant side need a certain time to switch on.
The modulation amplifier of your AE 4200 R is sensitive enough and enables you in
most cases to speak with even more distance, depending on how loud your voice is.
An automatic regulator ensures that your partner always hears your signal at the
same volume.
It is best to test the best distance from the microphone for yourself with the help of
another station.

12
External sockets
External loudspeaker
Depending on the surrounding noise, it can be advisable to hook up an external
loudspeaker. Usual commercial radio loudspeakers with 4-8 ohms impedance and 2-
4 W minimum output can be plugged in.
The cable can be up to 3 metres long. For car loudspeakers, make sure to use a
two-pin 3.5 mm jack plug and ensure that none of the loudspeaker connections are
attached to the vehicle chassis.
Microphone socket
Your AE 4200 R has an 4 pin standard microphone socket on the front side.
The wiring corresponds to international standards used by many manufacturers
since many years.
Apart from the hand microphone included in the package, you can also hook up
other microphones, with or without preamplifier, or with or without data transmitting
devices. According to the latest regulations you are also allowed to plug in modems
or so-called TNC`s for data transfer (Packet Radio). However, other type of
microphones must be specially soldered to the 4 pin connector.
Please note that data transfer is only permitted on certain channels and only for non-
commercial use and not in all countries.
Service and Warranty information
Troubleshooting
Check at first the power supply and the fuse. A problem may be caused through
power supply, when no LED light appears after switching on. If the unit works in a
strange way, disconnect the power supply cable (or take out the fuse from the
holder), while the radio remains switched on, wait some time (minimum 10 seconds),
and then reconnect power cord again.
Check the microphone and antenna connector. We think You cannot do more in
case of a problem. Please ask Your dealer or consult our service hints in the
Internet. If You should return the radio to Your dealer for repair, do not forget to
describe the problem as exactly as possible.
Please never return any radio to our service partner without consulting the technical
Hotline via phone or e-mail.
Many small problems can be cleared already via phone or mail, and in case that a
service repair should really be necessary, the Hotline will be able to tell you the
nearest and most fast service partner for your radio!

13
European 2 years warranty
The distributor, dealer or retail shop where You bought the radio warrants to the
original retail purchaser of this product that should this product or any part of it, under
normal use and conditions, be proven defective in material or workmanship within 2
years from the date of original purchase, such defect(s) will be repaired or replaced
with new or reconditioned product without charge for parts and repair labour. To
obtain repair or replacement within the terms of this warranty, the product is to be
delivered with proof of warranty coverage (e.g. a copy of your bill of sale),
specification of defect(s), to the distributor, dealer or his authorised repair centre.
Liability for communications range of this product is disclaimed. The warranty does
not apply to any product or part there of which, has suffered or been damaged
through alteration, improper installation, mishandling, misuse, neglect, accident, or
by removal or defacement of the factory serial number label(s). The warranty does
not apply to accessory parts or problems caused through not authorised or not
recommended accessories like other than the supplied microphone, external
antennas, external power supplies and over voltage caused through external power
supplies, lightning or over voltage defects via antenna or other cables, broken or
damaged acrylic glass windows and cabinet parts.
Please contact the dealer or person where You have purchased Your CB radio.
If you have bought your radio in Germany, you can also contact our service partner
directly in case where you need any support.
Where to find service hints and service documentation
The complete technical documentation is updated regularly. You can download the
latest versions of user manuals, technical documents and conformity declaration, as
well as service hints or FAQ’s any time from our server under
http://www.service.alan-electronics.de
If you should have a problem, please have a look to the service hints or frequently
asked questions (FAQ) before you send the CB radio back to the service centre.
Please note that the acceptance of AM+FM and 4 W in the different European
countries has just started and may be subject to unpredictable changes. Our
homepage will provide the latest information about using the radio.

14
Technical Details
Microphone socket wiring For Packet Radio & others
Pin 1 Mic audio Pin 1 Transmit audio
Pin 2 Ground Pin 2 Ground
Pin 3 PTT-RX (on ground for receiving) Pin 3 Receive audio
Pin 4 PTT-TX (on ground for transmit) Pin 4 PTT key
Transmitter
Transmitting power 4 Watt FM
4 Watt AM /CEPT –ECC DEC (11)03
Modulation sensitivity appr. 10 mV at >1 kOhm
Harmonic and spurious radiations less than -90 dBc = 4 nW
Max. frequency deviation less than 2.0 kHz
AM modulation degree up to 90% under EN 300 433-2
specifications and limits
Receiver
Sensitivity (FM) (SINAD) better + 3db µ V EMK for 20 dB
Sensitivity (AM) (SINAD) better + 3db µ V EMK for 12 dB
Adjacent channel selection better 60 dB (EN 300 135-1)
better 48 dB (EN 300 433-1)
Intermodulation rejection better 54 dB (EN 300 135-1)
better 48 dB (EN 300 433-1)
Image rejection better 48 dB (EN 300 433-1)
Audio output power ca. 2 Watt to 8 Ohm load
© Alan Electronics GmbH, June 2012
www.alan-electonics.de, www.albrecht-online.de, www.service.alan-electronics,de
Technical Hotline (Germany only) (+49) (0) 1805 012204 (14 cents / minute,
mobile networks may charge up to 42
cents/minute)
e-mail: [e-mail]
In other countries please contact your local distributor for any support matters.

15
Albrecht Radio Passport AE 4200 R
The radio may be used as mobile CB radio in European Countries according to following information, which we
publish as “Radio Passport”. Because the number of countries which have implemented the new CB standards
with 4 Watt AM and 4 Watt FM is changing within the next time, the latest version of this radio passport is
published on our Internet Web server and may be downloaded any time. (http://www.service.alan-
electronics.de) The version printed in this user manual has been issued in June 2012.
Country Country switch Licence and operating conditions
Operation only with ind
ividual licence or other restrictions
Austria 40 FM 4W Austria’s legislation does not accept radios with
country switches, please do not use in Austria or ask
your distributor for a version without country switch.
Italy * 40FM 4W and 40 AM 4 W Licence and regular charges for all CB radios,
Foreign travellers may use their radios free of
charges & license during travelling in Italy.
Switzerland and
Liechtenstein 40 FM 4 W and 40 AM 4 W Licence and monthly charges for Residents of Switzerland until end of 2012, FL free. Free for
travellers .
Spain 40 FM 4 W and 40 AM 4 W Licence and regular charges for Residents, free for
travellers.
Operation without licence and charges allowed
Belgium 40FM 4 W and 40 AM 4 W
announced to start within
2012)
Free of licence and charges for all users
Czech Republic 80/40 mode 4 W Free of licence and charges for all users, but AM
channels are not yet allowed to be used, but is
announced to start during 2012
Denmark 40 FM 4W Free of licence and charges for all users
Finland, Lithuania * 40 FM 4 W and 40 AM 1W Free of licence and charges for all users
France, Monaco 40 FM 4 W and 40 AM 1 W Free of licence and charges for all users
Germany * up to 80 FM and 40 AM (4W) Free of licence and charges for all users except in
some border regions for base stations using
channels 41-80 FM
Great Britain (UK) 40 FM (AM 4 W in
preparation) Free of licence and charges for all users
Greece 40 FM 4 W and 40 AM 4 W Free of licence and charges for all users
Hungary 40 FM 4 W Free of licence and charges for all users
Iceland 40 FM 4 W Free of licence and charges for all users
Ireland 40 FM 4 W and 40 AM 1W Free of licence and charges for all users
Malta 40 FM 4 W Free of licence and charges for all users
Netherlands 40 FM 4 W and 40 AM 1 W Free of licence and charges for all users
Norway 40 FM 4 W and 40 AM 4 W Free of licence and charges for all users
Bulgaria, Croatia,
Estonia *, Latvia *,
Luxembourg , Poland,
Portugal, Romania and
Slovenia
40 FM 4 W and 40 AM 1 W
in Croatia, Cyprus, Estonia,
Slovenia and Luxembourg
AM allowed with 4 Watts
Free of licence and charges for all users
Spain 40 FM 4 W and 40 AM 4 W Free of licence and charges for travellers
Sweden 40 FM 4 W and 40 AM 1 W Free of licence and charges for all users
Slovak Republic 80/40 mode (4 W) Free of licence and charges for all users, but only
FM on CH 1-40 & 70-80 allowed, AM 40 CH
announced for 2012
Switzerland and
Liechtenstein 40 FM 4 W and 40 AM 4 W Free of licence and charges for travellers
Important Note: Please respect the licence conditions in the above listed countries and do not use the radio
without licence, where necessary. For travelling with your radio, we recommend to provide a copy of this Radio
passport. The above list is based on public available information, while country specific requirements (especially
the 4 W AM implementation) may change without notice during the harmonisation process in Europe, we
recommend to ask local authorities before travelling, or use only FM when further information is not available.
* In some countries limitations of the radiated power (ERP resp. EIRP) of fixed antenna installations are applied.
Please use only allowed antennas or use antennas with suitable attenuation elements.

16
Declaration of Conformity / Konformitätserklärung
We herebydeclarethatourproduct: / Wirerklärenhiermit,dass unser Produkt
CB-Radio Albrecht AE 4200 R
satisfies all technical regulations applicable to the product within the scope of EU Council Directives,
European Standards and national frequency applications:/ alle technischen Anforderungen im
Geltungsbereich der EU Richtlinien,europäischer NormenundnationalerFrequenzanwendungen einhält:
73/23/EEC, 89/336/EEC / 2004/108/EG and 99/5/EC
EN 300 135 - 2 V 1.2.1/ EN 300 433- 2 V 1.3.1
EN 301 489- 01 V.1.8.1, EN 301 489-13 V1.2.1, EN 60 950-1: 2006, 2.Ausgabe,
2004/104/EG/Anh. I 6.5, 6.6, 6.8, 6.9
All essentialradiotestsuites havebeencarried out. /
Allefür dasProduktvorgeschriebenenFunktestreihenwurdendurchgeführt.
This declaration is issued under our sole responsibility. Basing on not yet harmonized frequency
applications, the CB radio may be used only in listed countries according to selected channel and AM
power programming. An individual license for operating this radios in AM+FM on 40/40 channels in CH,
(only until end of 2012), E, I and RSM is requested byresidents of these countries.
InD (whereupto80FMand40AMchannelsareallowed,B,BG,CY,CZ(80FM),EST,F,FIN,GR,HR,IRL,L,LT,
LV, N, NL,P,PL, RO , S, SLO andSK(only1-40 &70-80 FM) theCB operation on40 /40 channels inAM +FMis
free of license and free of charges. If the radio is programmed to 40 FM only, it may be used without
license and free of charge in all EU member states + N, IS, except Austria, where radios with (German)
country switches are generally not allowed to use. Residents of Italy / San Marino, Spain, Switzerland
(only until end of 2012) need a CB license, while travellers from other European countries may use their
radios during traveling in these countries free of licence and charges. In some countries limitations of the
radiated power (ERP/EIRP) are applied for fixed antenna installations.Pleaseuse onlyallowedantenna types or
attenuatingelements wherenecessary.
Diese Erklärung wird unter unserer alleinigen Verantwortung abgegeben. Die oben genannten
Funkgeräte dürfen wegen der noch nicht harmonisierten Frequenzanwendungen in den Ländern CH (bis
Ende 2012), E, Iund RSM von Bewohnern nur mit gültiger CB-Funkgenehmigung benutzt werden. In D
(max. 80 FM / 40 AM Kanäle), BG, CY, CZ (nur 80 FM), EST, F, FIN, GR, HR, IRL, L, LT, LV, N, NL, P, PL,
RO, S, SLO undSK (nur FM auf 1-40 & 70-80) ist der CB-Funk anmelde- und gebührenfrei. Dabei ist in
Deutschland mit der Programmierung 80 FM der ortsfeste Sendebetrieb auf den Kanälen 41-80 in
bestimmten Regionen entlang der Grenzen (außer zu CZ) nicht oder nur mit Sondergenehmigung
gestattet.
Mit der Programmierung 40 FM können die Geräte in allen EU und EFTA Staaten, außer Österreich
anmelde- und gebührenfrei benutzt werden. In A sind Funkgeräte mit (deutscher) Länderumschaltung
generell nicht erlaubt. Bewohner Italiens, Spaniens und der Schweiz (bis Ende 2012) benötigen in Ihrem
Heimatland eine Genehmigung (CB Lizenz). Die vorübergehende Benutzung durch Reisende aus anderen
europäischen Ländern ist in diesen Ländern jedoch auch anmelde- und gebührenfrei erlaubt. In einigen
Ländern gibt es Einschränkungen für die Strahlungsleistung (ERP/EIRP) über ortsfeste Antennenanlagen.
Benutzen Sienur einerlaubtes Antennensystem und, falls notwendigauchmit entsprechendem Abschwächer.
ALAN Electronics GmbH declara, bajo su responsabilidad, que este aparato cumple con lo dispuesto en la
Directiva 99/05/CE, del Parlamento Europeo y del Consejo de 9 de marzo de 1999, transpuesta a la legislación
española mediante el Real Decreto 1890/2000, de 20 de noviembre"
Point of contact/Ansprechpartner: Dipl.-Phys. Wolfgang Schnorrenberg
Place and date of issue:
Lütjensee, 20.6.2012
This Declaration and the Radio Passport will be revised periodically and can be downloaded any time from
www.service.alan-electronics.de. We are not liable for any information about the national implementation process of CEPT /
ECC decision ECC DEC(11)03 . - Diese Konformitätserklärung und der Albrecht Gerätepass werden regelmäßig aktualisiert
und sind unter www.service.alan-electronics.de in der jeweils gültigen neuesten Version abrufbar. Wir übernehmen keine
Gewähr für Informationen über die Implementierung der CEPT / ECC Entscheidung ECC DEC(11)03 in den einzelnen
Ländern, die erst ab 1.10.2011 begonnen hat.