Alcatel Temporis IP150 User manual

Temporis IP150
Administrator and Provisioning Manual

Temporis IP150 Administration and Provisioning Guide ed 0.1 2/106
Congratulations on your purchase of this Alcatel Temporis IP product. Before using this
Alcatel Temporis IP product, please read Important Safety Information on page 105 of
this manual. Please thoroughly read this manual for all the feature operations and
troubleshooting information necessary to install and operate your new product. You can
also visit our website at alcatel-business.com.
This manual provides instructions for using your Temporis IP150 telephone with software
version 0.64 or newer. See page 14 for instructions on checking the software version on
the deskset.
Parts checklist
Your telephone package contains the following items. Save your sales receipt and original
packaging in the event warranty service is necessary.
Quick Start Guide
Handset and handset cord
Phone base
Foot stand
Wall mount accessory
Ethernet cable

Temporis IP150 Administration and Provisioning Guide ed 0.1 3/106
Table of contents
Parts checklist ................................................................................................... 2
Audience ........................................................................................................... 5
Related documents............................................................................................. 5
About your phone............................................................................................... 5
Quick reference guide ......................................................................................... 6
Programmable Keys ........................................................................................... 7
Other possible programmable key settings ......................................................... 7
IP Addresses and Connectivity ............................................................................. 8
Deskset installation ...........................................................................................10
Idle Screen.......................................................................................................12
Status..............................................................................................................14
Viewing Line status ........................................................................................15
Using the Admin Settings menu ..........................................................................15
Network Setting ................................................................................................16
Line Menu ........................................................................................................17
Saving Your Settings .........................................................................................20
Status..............................................................................................................21
SIP Account Management...................................................................................22
Dial Plan ..........................................................................................................24
Call Settings .....................................................................................................34
User Preferences ...............................................................................................36
Programmable Keys ..........................................................................................39
Memory Keys: Speed Dial ..................................................................................43
Signaling Settings .............................................................................................44
Ringer Settings .................................................................................................46
Basic Network Settings ......................................................................................47
Advanced Network Settings ................................................................................48
Local Directory..................................................................................................51
Directory Import/Export .................................................................................51
Directory Import using configuration files..........................................................54
Black List .........................................................................................................55
Black List Import/Export .................................................................................55
Black List Import using configuration files .........................................................56
LDAP Directory .................................................................................................57
Broadsoft Directory ...........................................................................................60
Call History ......................................................................................................62
Reboot.............................................................................................................63
Time and Date ..................................................................................................63
Firmware Upgrade.............................................................................................67
Provisioning......................................................................................................69
Security ...........................................................................................................74
Certificates .......................................................................................................76
System Logs.....................................................................................................78
Resynchronization—Configuration File Checking ....................................................80
The Provisioning Process ....................................................................................80
Phone Restart ...................................................................................................81
Configuration File Types .....................................................................................81
Data Files.........................................................................................................82
Configuration File Guide .....................................................................................82
Guidelines for the MAC-Specific Configuration File ..............................................82
Securing Configuration Files with AES Encryption ...............................................83
“sip_account” Module: SIP Account Settings .........................................................88
“network” Module: Network Settings ...................................................................91
“profile” Module: security settings .......................................................................92
“provisioning” Module: Provisioning Settings.........................................................93

Temporis IP150 Administration and Provisioning Guide ed 0.1 4/106
“ringersetting” Module: distinctive ringing settings ................................................94
“time_date” Module: Time and Date Settings........................................................94
“log” Module: Log Settings .................................................................................95
“remoteDir” Module: Remote Directory Settings....................................................96
“web” Module: Web Settings...............................................................................97
“user_pref” Module: User Preference Settings .......................................................98
“call_settings” Module: Call Settings ....................................................................99
“pfk” Module: Programmable Feature Key Settings ..............................................100
“memory_key” Module: Speed Dial Settings .......................................................100
“file” Module: Imported File Settings .................................................................101
“tone” Module: Tone Definition Settings .............................................................102

Temporis IP150 Administration and Provisioning Guide ed 0.1 5/106
Introduction
This administrator and provisioning guide contains detailed instructions for installing and
configuring your Temporis IP150 IP phone. Please read this guide before installing the
telephone.
Audience
This guide is written for installers and system administrators. It assumes that you are
familiar with networks and VoIP, both in theory and in practice. This guide also assumes
that you have ordered your IP PBX service and selected which PBX features you want to
implement. This guide does not reference specific IP PBX services except for features or
parameters that have been designed for a specific service. Please consult your service
provider for recommended switches, routers, and firewall and NAT traversal settings, and
so on.
As the Temporis IP150 deskset becomes certified for IP PBX services, we may make
available interop guides for those specific services. These will recommend second-party
devices and settings, along with deskset-specific configurations for optimal performance
with those services. Contact your distributor or installer for the latest updates.
Related documents
The Temporis IP150 Quick Start Guide contains a quick reference guide to the deskset
external features and brief instructions on connecting the deskset to a working IP PBX
system.
The Temporis IP150 User’s Guide contains a quick reference guide, connection
instructions, instructions for making and receiving calls, and a guide to all user-
configurable settings.
The documents are available from our website at alcatel-business.com.
About your phone
The Temporis IP150 phone is full-featured business phone designed to work with popular
SIP telephone (IP PBX) services. Once you have ordered and configured your SIP service,
the deskset enables you to make and receive calls as you would with any other business
phone. The phone provides calling features like hold, transfer, conferencing,
speakerphone, quick dial numbers and one-touch voicemail access.
There are two network ports, known as the LAN port and PC port, at the back of the
deskset. The LAN port allows the Temporis IP150 deskset to connect to the IP PBX via a
router. The PC port is for another device such as a personal computer to connect to the
Ethernet network through the deskset.
You can configure the deskset using the deskset’s own menus, a browser-based interface
called the WebUI, or an automatic provisioning process (see Provisioning Using
Configuration Files on page 80). The WebUI enables you to configure the deskset using a
PC that is connected to the same Local Area Network. The WebUI resides on the deskset,
and is updated with any firmware updates.
The Temporis IP150 deskset supports intercom and call transfers between system
extensions and can connect you and two other parties on the same conference call.
The telephone also has 10 dual-function programmable keys. Your system administrator
can program up to 18 quick-dial numbers for these keys. Some of those keys can also be
programmed to monitor other desksets in the system. The left hand side programmable
keys have two-color LEDs to indicate call activity. You can press the key for a monitored
extension to answer a call at your own deskset.

Temporis IP150 Administration and Provisioning Guide ed 0.1 6/106
This telephone supports caller ID with call waiting service. Caller ID services are
subscriber services available from many telephone service providers for a fee. The
telephone can store up to 200 Call Log entries.
The Temporis IP150 IP Phone features include:
2.5-inch backlit Liquid Crystal Display
Speakerphone, Headset, Hold and Mute
Up to 2 SIP Registrations
Up to 6 active SIP sessions
3-way conferencing
10 dual-function programmable keys
10 speed dial numbers (long press dial keypad)
Message Waiting alert LED
Dual 10/100 Mbps Ethernet ports
Power over Ethernet enabled
200-entry Call Log
Getting started
Quick reference guide
The controls you will need to use to configure the phone manually are described below.
Navigation key also provides shortcuts to the following functions in idle mode:
MENU
Press to enter the menu.
CANCEL
While in a menu, press to cancel
an operation and exit the menu.
In idle mode, long press to
reboot the phone
OK
Press to select a menu item
or save an entry or setting.
NAVIGATION KEY
While in menus, press
or to scroll
through the menu,
highlight items or
change settings. While
entering names or
numbers, press or 
to move the cursor left
or right.
Line
Press to change
dial-out account
(shown if second
sip account is
registered only)
Hold key
In conversation, press to
place active call on hold.
In idle mode, press to
quickly access Network
Status menu
Settings
Press to quickly access User
Settings menu
Redial
Press to access redial list
Line
Press to switch dial out account
Voicemail
Press to access Voicemail
menu
Call history
Press to access your call
logs

Temporis IP150 Administration and Provisioning Guide ed 0.1 7/106
The deskset external features that are relevant to installation and configuration are
described below.
Programmable Keys
The table below lists the default settings for the programmable keys. The key
assignments on your phone may be different. Some keys may be programmed as Quick
Dial keys, for example. To assign functions to programmable keys, see Programmable
Keys on page 39.
Key Number
Setting
1
Line 1*
2
Line 1
3
Quick dial
4
Quick dial
5
Access to F11-F20
6-14
Quick dial
15
Access to F11-F20
16-20
Quick dial
* You can assign more than one key to a line. For example, you can configure keys 1 and
2 to access Line 1, and keys 3 and 4 to access Line 2. Label the keys appropriately for
deskset users after configuration.
Other possible programmable key settings
Directory
Call History
Redial
Messages
Programmable keys
Can be programmed to perform various functions or access
various features.
For example:
Press to access a line to make a call
Press to dial a monitored extension or a
quick-dial number
Press to answer a ringing call on any line
or monitored extension
See also Programmable Keys on page 7.
Directory card
To write names on the directory card, pull out the directory card
from under the plastic cover.
Access F11 To F20
Press F5 to switch to the second possible value of a programmable key.
Note: This is the default setting. You can configure F5 to perform other
functions
RJ9 Corded headset input (on side)

Temporis IP150 Administration and Provisioning Guide ed 0.1 8/106
Do not disturb
Quick Dial
BLF—Busy lamp field keys let you monitor activity at other phones. The key LED
indicates call status.
Call Forward Unconditional
Call Forward Busy
Call Forward No Answer
Call Forward All
Park Call—Dials the access code to park your current call. To program access
codes, see SIP Account Management on page 22.
Retrieve Parked Call—Dials the access code to retrieve a parked call.
In Call DTMF—Dials a string of numbers while you are on a call. For example,
pressing the key might dial a conference access code.
Call Back—Dials the number of the last missed call.
Intercom—If this feature is enabled, press the Intercom key to call one or a group
of phones. You can configure Intercom calls to be automatically answered. See
SIP Account Management on page 22.
Group Call Pickup—Dials the Group Call Pickup code, allowing you to answer a call
ringing at another extension.
Direct Call Pickup—Dials the Direct Call Pickup code, allowing you to answer a call
ringing at a specific extension. After pressing the button, you may need to enter
the extension number manually.
Network Requirements
A switched network topology is recommended for your LAN (using standard 10/100
Ethernet switches that carry traffic at a nominal rate of 100 Mbit/s).
The office LAN infrastructure should use Cat.-5 (or better) cable.
The LAN connections to the deskset(s) should all be wired. However, wireless
connections to other devices (such as laptops) in your office will not impede
performance.
All desksets must reside on a single subnet. A DHCP server is recommended and must be
on the same subnet as the desksets so that IP addresses can be auto-assigned. In most
cases, your network router will have a Dynamic Host Configuration Protocol (DHCP)
server that will automatically assign IP addresses to desksets. By default, the deskset
has DHCP enabled for automatic IP address assignment.
If no DHCP server is present, you can assign static IPs to desksets. If you do not have a
DHCP server or do not manually assign static IPs, you will not be able to access the
WebUI and/or enable automatic time updates from an NTP server.
Unless you want to manually set the system clock and manually upgrade deskset
software, an Internet connection to the LAN is required.
A DNS server is recommended to resolve the path to the Internet and to a server for
firmware and configuration updates.
If necessary, the system administrator can also download upgrade files and use the
WebUI to update the deskset firmware and/or configuration settings manually.
For users whose computers require a GigE Ethernet frame rate (a gigabit per second),
use separate Ethernet connections for the Deskset and the computer. The Ethernet
connection through a Deskset is limited to 100 Mbits/s.
IP Addresses and Connectivity
An IP address is an individual numeric identification assigned to devices on a computer
network. Valid IP addresses on the same subnet allow devices on the network to identify

Temporis IP150 Administration and Provisioning Guide ed 0.1 9/106
each other and enable communication. To enable access to the WebUI, at least one
deskset needs a valid IP address on the same subnet as the computer you are using to
access the WebUI.
This IP address may be assigned from a Dynamic Host Configuration Protocol (DHCP)
server, or set statically to the same subnet, and will be separate from the self-assigned
169.254.xxx.xxx link-local address that the desksets use to communicate with each
other. When setting up the IP address on a deskset, this network IP address used for
WebUI connectivity is the only address you can change.
The network IP addresses can be assigned in two ways:
1. The deskset can request a network server to automatically assign an IP address. This
IP address is a dynamic assignment; the address is on lease from the server. The
lease is renewed as long as the device remains connected and there is no change to
the network. However, if the device is disconnected, or if there is a network or AC
power interruption, the lease may not be renewed (that is, the IP address expires)
and a new IP address may be assigned.
Note: Some DHCP servers have default settings that limit the number of network IP
addresses assigned to devices on the network. You should log in to your server to
confirm that the IP range is sufficient to accommodate at least one of the desksets that
you are adding. Consult the IT department if you need help checking the server.
2. You can manually assign a static IP address to a deskset. This IP address does not
change, even when there are network or AC power interruptions. Some installations
will require manual static IP assignment. You can assign a static IP address for a
deskset from the deskset IP Settings menu. See “Deskset IP Settings” on page 71.
Installation
This section assumes that your network infrastructure is established and that your hosted
IP PBX service has been ordered and configured for your location.
Install the phone close to a router or network switch. You can power the phone using
Power over Ethernet (PoE—Class 2) or the power adapter (not supplied). If you are not
using PoE, install the phone near a power outlet not controlled by a wall switch. The
phone can be placed on a flat surface or vertically mounted on the wall.
For customer service or product information, visit our website at alcatel-business.com.
Avoid placing the deskset too close to:
Communication devices such as television sets, DVD players, or other cordless
telephones.
Excessive heat sources.
Noise sources such as a window with traffic outside, motors, microwave ovens,
refrigerators, or fluorescent lighting.
Excessive dust sources such as a workshop or garage.
Excessive moisture.
Extremely low temperature.
Mechanical vibration or shock such as on top of a washing machine or work
bench.

Temporis IP150 Administration and Provisioning Guide ed 0.1 10/106
Figure 1: Temporis IP150 Installation Example
Deskset installation
To install the phone:
1. If you plan to place the phone on a flat surface, you can use the phone with or
without the foot stand depending on the work angle you wish to have. To assemble
the stand line up the tabs on the stand (marked with triangles) with the slots on the
rear of the phone as shown in the picture
Plug the end of the coiled handset cord into the Handset jack on the side of the
phone.
2. Plug one end of the Ethernet cable into the Ethernet port at the back of the console,
and plug the other end of the cable into your network router or switch.

Temporis IP150 Administration and Provisioning Guide ed 0.1 11/106
NOTE: You may need to use a network switch connected to your router if your router
does not have sufficient ports for the number of phones you want to install. If you use
a network switch, connect the phone to the switch instead of the router in the
previous step.
3. If the deskset is not using power from a PoE-capable network router or switch:
a. Connect the power adapter to the deskset power jack.
b. Plug the power adapter into an electrical outlet not controlled by a wall
switch.
IMPORTANT INFORMATION
1. Use only original power adapters. Contact your distributor to order.
2. The power adapter is intended to be correctly oriented in a vertical or floor mount
position. The prongs are not designed to hold the plug in place if it is plugged into a
ceiling, under-the-table or cabinet outlet.
If there is a networked computer and no extra Ethernet wall ports near the phone, then
the phone and PC can share the same network connection.
To share a network connection with a PC:
1. Plug a Cat.-5 Ethernet cable into the PC port on the phone.
2. Plug the other end of the Cat.-5 Ethernet cable into your computer’s network port.
If a GigE network is being used, a computer connected through the phone will be
limited to 100 Mbits/s. If you require a GigE Ethernet rate, use separate Ethernet
connections for the phone and the computer.
If a PC is connected to your network through a phone, any phone resets and
power or network interruptions will disrupt the PC’s connection to the network.
To mount the phone on the wall:
1. Put the corded handset aside. Use a coin to rotate the handset tab 180 degrees. The
protruding edge holds the corded handset when the phone is mounted on the wall.

Temporis IP150 Administration and Provisioning Guide ed 0.1 12/106
2. Assemble wall mount accessories as depicted
3. Connect the network cable(s) and power adapter (if required).
4. Hang the phone on the wall using the upper holes in the wallmount accessory.
Verifying the installation
Idle Screen
The idle screen appears after the phone is connected and configured for your SIP PBX
service. The idle screen indicates that you have no active or held calls.
Figure 2: Idle screen
Note “Line” softkey will be shown only if you have configured and registered more than
one sip account.

Temporis IP150 Administration and Provisioning Guide ed 0.1 13/106
Configuring the Phone
You can configure the phone using one of three methods:
From the phone itself, using the menus. The phone menus are best suited to
configuring a few settings, perhaps after the initial setup has been done. For
administrators, the settings available on the phone menus are limited to network
settings. See Using the Admin Settings menu on page 15. Most of the settings
accessible on the phone itself are most useful for end users. Through the menu,
they can customize the screen appearance, sounds, and manage calls. For more
information, see the Temporis IP150 User Guide.
The Web User Interface, or WebUI, which you access using your Internet browser.
See Using the WebUI on page 19. The browser-based interface is easy to navigate
and best-suited to configuring a large variety of phone settings. The WebUI has
every setting required for configuring a single phone. You can enter service
provider account settings on the WebUI, configure the programmable keys, and
set up provisioning, which will allow you to automatically and remotely update the
phone after initial configuration.
The configuration file. Working with configuration files is the best way to
configuring multiple phones. There are several methods available to enable the
phone to find the configuration file. For example, you can enable the phone, when
it starts up or reboots, to check for the presence of a configuration file on a
provisioning server. If the configuration file is new or has been modified in any
way, the phone automatically downloads the file and applies the new settings. For
more information, see Provisioning Using Configuration Files on page 80.
Using the Phone Menu
The phone menu has four main sub-menus:
Features—manage calls, view and add directory entries, view call history, access
messages, and use the speed dial menu.
Status—view the deskset network status, account registration status, and
product information.
User Settings—allows the user to set the language for the display, configure the
appearance of the display, customize the audio settings, and register a DECT
headset.
Admin Settings—configure network settings (enter static IP addresses, for
example) and line settings.
This guide contains instructions for using the Admin Settings menu and for accessing the
Status menu. See the Temporis IP150 User Guide for more information about Features
and User Settings.
To use the phone menu:
1. When the phone is idle, press MENU.
The main menu appears.
2. Press or to highlight the desired sub-menu, and then press OK.
You can also press a corresponding dial pad key to select a numbered menu item.
Press 2for the Status menu, for example.
Press OK or an appropriate soft key to save changes.
Press to cancel an operation, exit the menu display or return to the idle
screen.

Temporis IP150 Administration and Provisioning Guide ed 0.1 14/106
Status
Use the status menu to verify network settings and begin troubleshooting if network
problems or account registration issues affect phone operation.
You can also find the software version of the phone on the Product Info screen, available
from the Status menu.
To view the Status menu:
1. When the phone is idle, press MENU.
2. On the Main menu, press or to highlight Status, then press OK. The Status
menu appears.
3. On the Status menu, press or to highlight the desired menu, then press
SELECT.
The available status menus are:
Menu
Information listed
1. Network
IP address
DHCP status (Enabled/Disabled)
Subnet Mask IP address
Gateway IP address
DNS server 1 IP address
DNS server 2 IP address
SNTP server URL
MAC address
2. Line
Lines and registration status. On the Line menu, highlight
and select the desired line to view detailed line status
information:
Line status (Registered/Not registered)
Line display name
Line User ID
Server IP address
Server Port number
Proxy server IP address
Proxy server port number
3. Product Info
Model number
Serial number
MAC address
Software version
Hardware version

Temporis IP150 Administration and Provisioning Guide ed 0.1 15/106
Note
To view Network status you can also use the following shortcut. In idle mode, press
key.
Viewing Line status
When you select Line from the Status menu, the Line menu appears, listing the
available lines along with icons indicating each line’s current registration status.
Icon
Description
Line registered
Line not registered
Line disabled
To view complete status information for a line:
1. On the Line menu, press or to highlight the desired line, then press SELECT.
The full line status screen appears.
Using the Admin Settings menu
To access the Admin Settings menu:
1. When the phone is idle, press MENU. The Main menu appears.
2. Press or to highlight Admin Settings, then press SELECT.
-or-
Press 4 (Admin Settings) on the dial pad.
3. Use the dial pad to enter the admin password, the press SELECT. The default
password is admin.
The Admin Settings are:

Temporis IP150 Administration and Provisioning Guide ed 0.1 16/106
Setting
Options
1. Network setting
1. DHCP (Enable, Disable)
2. Set static IP
3. VLAN
4. Others
2. Line
1. LINE 1
2. LINE 2 (if available)
3. Provisioning
Configure provisioning server url, user and
password
4. Reset to default
Press SELECT to reset the phone to factory default
settings.
5. Restart phone
Press SELECT to restart the phone.
Network Setting
Use the Network setting menu to configure network-related settings for the phone.
Note: After you press Save for any of the network settings, the phone restarts.
To use the Network setting menu:
1. From the Admin Settings menu, press or to highlight Network setting, then
press SELECT.
The Network setting menu appears.
2. Press or to highlight the desired option, then press SELECT:
DHCP
Set static IP
Others (DNS and NTP servers).
To enable or disable DHCP:
1. From the Network setting menu, press or to highlight DHCP, then press SELECT.
2. Press or to select Enabled or Disabled, then press Save.
DHCP is enabled by default, which means the deskset will get its IP address from the
network. When DHCP is disabled, you must enter a static IP address for the deskset.
Note: You must be familiar with TCP/IP principles and protocols to configure static IP
settings.
To set static IP for the deskset:
1. From the Network setting menu, press or to highlight Set static IP, then press
SELECT.

Temporis IP150 Administration and Provisioning Guide ed 0.1 17/106
If DHCP is disabled, the Set static IP menu appears. If DHCP is enabled, an error
message appears briefly before returning you to the Network setting menu.
2. On the Set static IP menu, enter the static IP address. Use the dial pad and the Add
dot soft key to enter characters. Press or to advance to the next character.
3. Press and enter the Subnet Mask. Use the dial pad and the Add dot soft key to
enter characters. Press or to advance to the next character.
4. Press and enter the Gateway. Use the dial pad and the Add dot soft key to enter
characters. Press or to advance to the next character.
5. Press Save.
To set other settings (DNS and NTP):
1. From the Network setting menu, press or to highlight Others, then press
SELECT. The Others menu appears.
2. If DHCP is disabled or you don’t wish to use the DHCP-assigned DNS server (or one
specified by your service provider), enter the IP address for the primary DNS server.
Use the dial pad and the Add dot soft key to enter characters. Press or to
advance to the next character.
3. Press and enter the IP address for the secondary DNS server. The deskset uses this
server if the primary server does not respond.
4. Press and enter the IP address for the NTP server. If the deskset does not use an
NTP server, you must manually enter the time and date settings.
5. Press Save.
Line Menu
Use the Line menu to configure line-specific settings for the phone.
On the Line menu, you can configure:
Line status (Registered/Not registered)
Line display name
Line User ID
Auth ID
Password
Server IP address
Server Port number
Proxy server IP address
Proxy server port number
Line registration
Auto/manual answer page
To use the Line setting menu:
1. From the Admin Settings menu, press to highlight Line, then press SELECT.

Temporis IP150 Administration and Provisioning Guide ed 0.1 18/106
The Line menu appears.
2. Highlight the desired line, if necessary, by pressing , and then press SELECT.
The full configuration menu for that line appears. You can configure:
Display name
User ID
Authorization ID
Authorization Password
Server IP
Server port
Proxy server IP
Proxy server port
Register (On or Off)
Answer page (Manual or Auto)
For more information about these settings, see SIP Account Management on page 22.
3. Edit the Line settings using the dial pad and the soft keys available for each setting:
Backspc—deletes a character
123—enables you to enter numbers, lower case letters, or upper case letters with
the dial pad. Does not appear when the setting accepts numbers only.
Save—prompts you to reboot the phone and apply the new settings
Edit—enables you to edit the setting (appears for the Password setting)
Press or to advance to the next character.

Temporis IP150 Administration and Provisioning Guide ed 0.1 19/106
Using the WebUI
The Web User Interface (WebUI) resides on your phone. You can access it using an
Internet browser. After you log in to the WebUI, you can configure the phone on the
following pages:
System
oSIP Account Management
oCall settings
oUser Preferences
oProgrammable Keys
oMemory Keys
oSignaling Settings
oRinger Settings
Network
oBasic Network Settings
oAdvanced Network Settings
Contacts
oLocal Directory
oBlacklist
oLDAP
oBroadsoft
oCall History
Servicing
oReboot
oTime and Date
oFirmware Upgrade
oProvisioning
oSecurity
oCertificates
oSystem Logs
The WebUI also has a Status page, where you can view network status and general
information about your phone. The information on this page matches the Status menu on
the phone.
To access the WebUI:
1. Ensure that your computer is connected to the same network as your deskset. Your
computer may already be connected to the network through the PC port on the back
of your deskset.
2. Find the IP address of your phone:
a. When the phone is idle, press MENU.
b. Press to highlight Status, and then press SELECT.
c. With Network highlighted, press SELECT.
The Network status screen appears.
Note: Instead of steps a, b, c you can use the shortcut to Network status
(in idle mode press )
d. On the Network status screen, note the IP Address.

Temporis IP150 Administration and Provisioning Guide ed 0.1 20/106
3. On your computer, open an Internet browser. (Depending on your browser, some of
the pages presented here may look different and have different controls.)
4. Type the phone IP address in the browser address bar and press ENTER on your
computer keyboard.
5. A login box appears. Under Username, enter admin. For the password, enter the
default password, admin. You can change the password later on the Servicing >
Security page.
6. On the login box, click OK.
The WebUI appears.
Click topics from the navigation bar along the top of the WebUI, and then click links to
individual pages along the left. You view and change settings in two different types of
fields: drop-down lists and entry fields into which you type information. For your security,
the WebUI times out after 10 minutes, so if it is idle for that time, you must log in again.
The remaining procedures in this section assume that you are already logged into the
WebUI.
NOTE: The settings tables in this section contain settings that appear in the WebUI and
their equivalent tags in the configuration file template. Settings only available on the
configuration files are also described. You can use the configuration file template to
create custom configuration files. Configuration files can be hosted on a provisioning
server and used for automatically configuring phones. For more information, see
Provisioning Using Configuration Files on page 80.
Saving Your Settings
Each WebUI settings page has a Save button. Click Save to save any changes you have
made on the page. During a configuration session, click Save before you move on to the
next WebUI page.