Alcoa Huck HK150-S456 User manual
05-17-2004
Form HK922
INSTRUCTION MANUAL
MODEL HK150-S456
MANUAL INSTALLATION TOOL
HK150-S456 Series Tooling Alcoa Fastening Systems
SAFETY
This instruction manual must be read with particular
attention to the following safety guide lines, by any
person servicing or operating this tool.
1. Safety Glossary
WARNINGS - Must be understood
to avoid severe personal injury.
CAUTIONS - show conditions that will
damage equipment and or structure.
Notes - are reminders of required
procedures.
Bold, Italic type and underlining -
emphasizes a specific instruction.
2. Huck equipment must be maintained in a safe
working condition at all times and inspected on a
regular basis for damage or wear. Any repair
should be done by a qualified repairman trained
on Huck procedures.
3. Repairman and Operator must read manual prior
to using equipment and understand any Warning
and Caution stickers/labels supplied with
equipment before connecting equipment to any
primary power supply. As applicable, each of the
sections in this manual have specific safety and
other information.
4. See MSDS Specifications before servicing the
tool. MSDS Specifications are available from
you Huck representative or on-line at
www.huck.com. Click on Installation Systems
Division.
5. When repairing or operating Huck installation
equipment, always wear approved eye
protection. Where applicable, refer to ANSI
Z87.1 - 1989
6. Disconnect primary power source before doing
maintenance on Huck equipment.
7. If any equipment shows signs of damage, wear,
or leakage, do not connect it to the primary
power supply.
8. Make sure proper power source is used at all
times.
9. Never remove any safety guards or pintail
deflector.
10. Never install a fastener in free air. Personal
injury from fastener ejecting may occur.
11. When using an offset nose always clear spent
pintail out of nose assembly before installing the
next fastener.
12. If there is a pinch point between trigger and
work piece use remote trigger. (Remote
triggers are available for all tooling).
13. Do not abuse tool by dropping or using it as a
hammer. Never use hydraulic or air lines as a
handle. Reasonable care of installation tools by
operators is an important factor in maintaining
tool efficiency, eliminating downtime, and in
preventing an accident which may cause severe
personal injury.
14. Never place hands between nose assembly and
work piece.
15. Tools with ejector rods should never be cycled
with out nose assembly installed.
16. When two piece lock bolts are being used
always make sure the collar orientation is
correct. See fastener data sheet of correct
positioning.
!
Product complies with requirements
set forth by the relevant European
directives.
Read manual prior to using
equipment.
Eye protection required while
using this equipment.
Hearing protection required while
using this equipment.
DATA SHEET
122587
Nose/tool Adapter
TYPE:
99-S456 to HK150
FOR:
TOOL:
Huck International, Inc.
Installation System Division
1 Corporate Drive - Kingston, NY 12401
PRODUCT
REVISION:
REVISED:
C
3/11/03
NOSE ASSEMBLY
HK150
OTHER
©Huck International, Inc. 1995
©Registered Trademark of Huck International, Inc., Irvine, CA
™Trademark of Huck International, Inc., Irvine, CA
Alcoa Fastening
Systems
DATA SHEET
99-S456
UNIMATIC, Blind Rivet
TYPE:
U04;U05;U06, NAS1919;NAS1921
FOR:
TOOL:
Huck International, Inc.
Installation System Division
1 Corporate Drive - Kingston, NY 12401
PRODUCT
REVISION:
REVISED:
E
3/11/03
NOSE ASSEMBLY
HK150
OTHER
©Huck International, Inc. 1995
©Registered Trademark of Huck International, Inc., Irvine, CA
™Trademark of Huck International, Inc., Irvine, CA
Alcoa Fastening
Systems
HK-150 Riveter
12 Month Warranty
All Huck tools and parts have been carefully tested and checked at the factory and are guanranteed
to be free from defects in material and workmanship, subject to the following conditions:
A. The tools manufactured by Huck will be repaired free of charge or replaced at our discretion
within 12 months of sale to the first user if, upon examination at our service center, we find a
defect in material or workmanship in the hydraulic system.
B. The tool must be returned intact and prepaid to one of our service centers. Proof of date of
sale must accompany any tool returned. This warranty will be void if repairs have been made
or attempted by others, or if the tool has been subject to abuse, neglect, accident or improper
application.
C. The foregoing obligation is Huck’s sole liability under this or any implied warranty, and no one
is authorized to vary its terms or conditions.
D. If you have any problems please contact Customer Service at the factory at
800-278-HUCK (4825)
Before returning tools to the service center, please use the operation and maintenance tips on
page 5. If the tool continues to malfunction call the Customer Service Department at Huck for
Huck Certified Service Centers For the HK-150 Riveter:
Central Fastening Systems Inc J.O. King Inc • All Huck Service Centers have been
801 McCann Road 1265 Old Alpharetta Road factory certified to service the HK-150
Rogers, AK 72758 Alpharetta, GA 30201 Riveter
479 936 7577 770 751 1875
888 370 1894 (Toll Free) 800 241 2681 (Toll Free) • Only genuine Huck parts are used in
479 636 2119 (Fax) 770 442 0950 (Fax) the repair of your tools
Cooper Aviation Limited Universal Repair Shop • Most Service Centers can provide
Station Field Industrial Estate 1611 Boylston Avenue 24 hour turnaround of your tool -
Kidlington, Oxford OX54 1JD Seattle, WA 98122 please specify on your return
United Kingdom 206 322 2726 documentation that an expedited
01865 375 111 206 322 2126 (Fax) repair is required
Professional Tool Center FSI • Service Centers can handle repairs
2236 S.116th Street 1206 East Mac Arthur Street on other Huck products (AK-175)
West Allis, WI 53227 Sonoma, CA 95476
414 321 1234 707 935 1170 • Warranty Repairs are performed
414 321 2524 (Fax) 800 344 2394 (Toll Free) at only these Huck certified Service
707 935 1828 (Fax) Center
Other Alcoa Tools manuals
