Alderon Industries Versa'larm VA02A User manual

1. DISCONNECT ALL ELECTRICAL SERVICE BEFORE INSTALLING OR WORKING ON THE PRODUCT.
2. DO NOT USE WITH FLAMMABLE OR EXPLOSIVE FLUIDS SUCH AS GASOLINE, FUEL OIL, KEROSENE, ETC.
DO NOT USE IN EXPLOSIVE ATMOSPHERES.
3. ALARM PANEL MUST BE MOUNTED INDOORS. FOR OUTDOOR APPLICATIONS CONSULT FACTORY.
The 2-Zone Sump and Flood Versa’larm™alarm panel is powered by 120 VAC coming from standard wall outlets and is
transformed to 9-11.1 VDC. Installing a 9 Volt battery provides battery backup during power outages. The power LED
(green) will illuminate when powered.
When a switch (signaling device) contact “closes” the buzzer will annunciate, alarm LED (red) will illuminate for the zone the
closedswitch is connection to (Sump and/or Flood), and the built in auxiliary contacts will be activated.
Pressing the “Alarm Silence” pushbutton will silence the buzzer and the LED(s) (red) remain on. When the alarm condition
is cleared, the system automatically resets itself for the next alarm cycle.
1. Phillips screw driver
2. (Qty 2) #6 self tapping screws
3. Access to 120 VAC power receptacle
4. Optional - Plastic anchors (#8; Qty 2) if mounting to sheet rock
5. Optional - 9V battery (used for battery backup during power outages)
6. Optional - Wire stripper (used if you need to strip wire to connect to a BAS or SCADA system)
7. Optional - Needle nose pliers if using auxiliary contacts
Versa’larm™
Operation, Maintenance and Installation Manual
2-Zone Alarm - Model VA02A | Sump and Flood
Alderon Industries - Hawley, MN | 218.483.3034 | [email protected] | alderonind.com
Introduction of Installation
Safety Guidelines
Description of Operation
Tools, Supplies and Requirements for Installation - Not Included
Before proceeding with the installation or operation of the product, read all
instructions thoroughly, as well as complying with all federal, state and local
codes, regulations, and practices. The product must be installed by qualified
personnel familiar with all applicable local electrical and mechanical codes.
Refer to the National Electrical Code (NFPA 70). Failure to properly install and
test this product can result in personal injury or equipment malfunction.
Alarm Systems Control Panels Float Switches Leak Detection Systems Page 1 of 4

Versa’larm™
Operation, Maintenance and Installation Manual
2-Zone Alarm - Model VA02A | Sump and Flood
Installation of the Alarm Panel
1. To install/replace the battery for the backup power feature, remove the access cover (Fig. 1) and install 9 VDC battery
(Duracell model MX 1604B2 / Fig. 2). After installing battery, the green power LED should illuminate, then press and hold
the “Alarm Test” pushbutton (Fig. 3) to activate the alarm and make sure the battery is working properly. The buzzer should
annunciate and the alarm LEDs should illuminate. If using the auxiliary contacts, leave the access cover off until step 3 is
completed. If the auxiliary contacts are not used, replace the access cover (Fig. 4).
(Fig. 1) (Fig. 2) (Fig. 3) (Fig. 4)
2. Determine the mounting location for the alarm panel. Make sure power outlet (120 VAC, 50/60 Hz) is within 5-feet of the
alarm panel (Fig. 5). The power outlet should be on a separate circuit breaker from any other device and not on a switched
receptacle to maintain power integrity. Mount the alarm panel using two #6 self-tapping screws (not included / Fig. 6). Use
two #8 plastic anchors (not included / Fig. 7) if mounting the alarm panel to sheet rock.
(Fig. 5) (Fig. 6) (Fig. 7)
5 ft. Max
Alderon Industries - Hawley, MN | 218.483.3034 | [email protected] | alderonind.com
Alarm Systems Control Panels Float Switches Leak Detection Systems Page 2 of 4

Versa’larm™
Operation, Maintenance and Installation Manual
2-Zone Alarm - Model VA02A | Sump and Flood
Alderon Industries - Hawley, MN | 218.483.3034 | [email protected] | alderonind.com
Installation of the Alarm Panel Continued
3. If connecting to an existing alarm security system or building automation system (BAS), leave Terminals “+” and “-” open
and use 18 gauge 2-conductor wire to connect the existing product to Terminals 2A, 2B, 1A, and 1B (Fig. 8). When connect-
ed, replace the access cover and pull wire(s) through the knockout(s) on the access cover (see step 4). CAUTION! - Route
all wires away from sharp objects and internal components when installing wires.
AUXILIARY CONTACTS: (Fig. 8)
Terminals “+” and “-”
11.1 VDC, 100mA power supply for external equipment
Terminals 2A and 2B
Zone 2 Alarm (Flood Alarm)
Normally Open
Terminals 1A and 1B
Zone 1 Alarm (High Sump)
Normally Open
Class 2, 24 VDC/VAC (50/60 Hz)
100 Milliamps Maximum
Note: The auxiliary contacts 2A, 2B, 1A, and 1B of the alarm panel are Normally Open only.
+ -
2A 2B 1A 1B
+-
2A 2B 1A 1B
4. After the access cover has been removed from the alarm panel (Fig. 9), use a needle nose pliers (not included) to remove
the desired “break away tabs” from the access cover, lightly pull and twist off tab(s) (Fig. 10). Replace the access cover and
run wire(s) through the knockout(s) (Fig. 11).
(Fig. 9) (Fig. 10) (Fig. 11)
5. Make note of the alarm condition(s) you are monitoring and keep them near the alarm panel.
Alarm Systems Control Panels Float Switches Leak Detection Systems Page 3 of 4

Versa’larm™
Operation, Maintenance and Installation Manual
2-Zone Alarm - Model VA02A | Sump and Flood
Alderon Industries - Hawley, MN | 218.483.3034 | [email protected] | alderonind.com
Installation of the Alarm Panel Continued
6. Connect normally open sensor #1, sump probe (rated 9 VDC, 200mA Minimum) to Terminals C and 1 on the terminal
block of the alarm panel. Connect normally open sensor #2, flood sensor to Terminals C and 2 on the terminal block of the
alarm panel. See below (Fig. 12) for wiring example. The alarm is activated by a “closed” switch. CAUTION! - When install-
ing the “Signaling Device”, refer to its installation instructions for proper installation.
7. Plug the alarm panel power supply into a 120 VAC, 50/60 Hz standard
wall outlet and the green “Power” LED should illuminate (Fig. 13).
1. Test the alarm panel by pressing and holding the “Alarm Test” pushbutton (Fig. 14) or activating the “Signaling Device”
(i.e., float switch or water sensor / Fig. 15). The buzzer should annunciate and the alarm LED(s) should illuminate. Press the
“Alarm Silence” pushbutton and the buzzer should silence while the alarm LED(s) remain on. After you remove pressure
from the “Alarm Test” pushbutton or deactivate the “Signaling Device”, the “Auto Reset” feature reactivates the alarm panel
for the next alarm cycle. If testing with “Signaling Device”, make sure to test all devices for complete system operation. Test
product weekly to ensure system integrity.
Testing the Alarm Panel
(Fig. 12)
(Fig. 13)
(Fig. 14) (Fig. 15)
(#1)
(#2)
#1 - WaterSpotter™ Sump Probe
#2 - WaterSpotter™ Flood Sensor
5 ft. Max
Alarm Systems Control Panels Float Switches Leak Detection Systems Page 4 of 4