Alderon Industries VersAlarm I/O VLIO-0001 User manual

VersAlarm™I/O
Indoor/Outdoor Alarm Panel | Model: VLIO-0001
Safety Guidelines
Step 2: Installing Conduit / Fittings
Before proceeding with the installation or operation of this product,
read all instructions thoroughly, as well as complying with all federal,
state and local codes, regulations, and practices. This product must
be installed by qualied personnel familiar with all applicable local
electrical and mechanical codes. Refer to the National Electrical Code
(NFPA 70). Failure to properly install and test this product can result in
personal injury or equipment malfunction.
WARNING
Step 1: Remove Bottom Cover
QSG00001_Rev04_VLIO-0001_VersAlarm IO | September 19, 2022 10:41 AM
Remove the bottom enclosure cover screw, slide directly downward
(1A) and then pull directly away (1B).
Using the pre-marked center hole
locations (2A), mark and drill out
on the bottom of the enclosure.
The size(s) will depend on desired
conduit fitting (maximum 0.75″).
Place the conduit fitting (2B) in
the drilled out hole and make sure
it’s secured. Then, install conduit
(2C) into the fitting.
Note: Seal all conduits to prevent moisture and
gases from entering the enclosure per local codes.
CAUTION: Nonmetallic enclosure does not provide
proper grounding between conduit connections. Use
grounding bushings and jumper wires.
Step 3: Mount Enclosure
Determine the mounting location
for the VersAlarm™ I/O. Hold the
alarm up to the desired mounting
location, mark the drill hole
locations. Once marked, drill pilot
holes for screws (not included)
and use wall mount anchors (not
included) if necessary. Place
enclosure in mounting location,
adjust until the pilot holes are
lined up with the enclosure and
fasten screws to secure the alarm
panel in place.
QUICK START GUIDE
2A
2B
2C
1A
1B
Step 4: Wiring
The diagram below shows the six terminals on the terminal block that
consists of three pairs of connections.
1) Install the sensor to terminals 1 and 2.
2) Installing an auxiliary device to terminals 3 and 4 is optional.
3) Install incoming power to terminals 5 and 6, line (L1) in terminal 5
and neutral (N) in terminal 6.
4) NEVER leave ground wire exposed inside the panel, use provided
Wago connector for wire termination.
Installing Wire into Wago Connector:
1) Lift tab(s) upward.
2) Insert wire(s) into slot.
3) Press tab(s) downward.
4) Make sure wire(s) are secured.
POWERSENSOR AUX
1 2 3 4 5 6
TO OPEN
WAGO
TO CLOSE
WAGO

Included with Product
VersAlarm™I/O - Features
Customer Support
Specications
▪ (1) VersAlarm™ I/O alarm panel
▪ (1) Wago connector
Online
alderonind.com
Email
[email protected]
QR Code
Scan code for full product details
Primary Power: 120VAC, 50/60Hz
Power: 2.64 Watts maximum (alarm condition)
Certifications: FCC Part 15 (US/Canada), CSA (US/Canada)
Auxiliary Contacts: 24VDC @ 0.5 Amps maximum
Enclosure: Outdoor, rated Type 3R
FCC Part 15: NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures: increase the separation between the equipment and receiver,
connect the equipment into an outlet on a circuit different from that to which the receiver is connected, consult the dealer or
an experienced radio/TV technician for help. Caution: changes / modications not approved by Alderon Industries could void
the user’s authority to operate the equipment.
Step 5: Install Bottom Cover
Line up the bottom enclosure cover with the grooves (5A), then slide
directly upward (5B) until it meets the top of the enclosure so the screw
hole is lined up and replace the screw at the bottom of enclosure.
Step 6: Power Alarm and Quick Test
After all wiring and installation steps have been completed, power
the alarm with incoming voltage, 120VAC. Use the features list and
diagram below to perform a quick test of the alarm to make sure it is
working properly.
Note: For complete wiring, installation instructions, or troubleshooting,
refer to the user guide for this model by scanning QR code.
5A
5B
1Power On Indicator - Green LED illuminates enclosure cover
2Alarm Beacon - Red LEDs illuminate enclosure cover
3Alarm Buzzer - Annunciates to indicate an alarm condition
4Test/Silence Pushbutton - Activates alarm, silences alarm buzzer
5Sensor Input - Terminals for sensor connection
6Auxiliary Contacts - Interface with external device, 24VDC @ 0.5A maximum
7Power Mains Input - Terminals for line (L1) and neutral (N), 120VAC
8 Power Indicator Turn Off - Flip switch down to turn off green power LED
9 QR Code - Scan code for additional product information (alderonind.com)
8
9
1 2
3
4
57
6