Alderon Industries Versa'larm VA01A User manual

Alarm Systems Control Panels Float Switches Leak Detection Systems Page 1 of 4
1. DISCONNECT ALL ELECTRICAL SERVICE BEFORE INSTALLING OR WORKING ON THE PRODUCT.
2. DO NOT USE WITH FLAMMABLE OR EXPLOSIVE FLUIDS SUCH AS GASOLINE, FUEL OIL, KEROSENE, ETC.
DO NOT USE IN EXPLOSIVE ATMOSPHERES.
3. ALARM PANEL MUST BE MOUNTED INDOORS. FOR OUTDOOR APPLICATIONS CONSULT FACTORY.
1. Phillips screw driver
2. (Qty 2) #6 self tapping screws
3. Access to 120 VAC power receptacle
4. Optional - Plastic anchors (#8; Qty 2) if mounting to sheet rock
5. Optional - 9V battery (used for battery backup during power outages)
6. Optional - Wire stripper (used if you need to strip wire to connect to a BAS or SCADA system)
7. Optional - Needle nose pliers if using auxiliary contacts
Versa’larm™
Operation, Maintenance and Installation Manual
Alderon Industries - Hawley, MN | 218.483.3034 | [email protected] | alderonind.com
Introduction of Installation
Safety Guidelines
Description of Operation
Tools, Supplies and Requirements for Installation - Not Included
1-Zone Alarm - Model VA01A
P/N: 101444
The 1-Zone Versa’larm™alarm panel is powered by 120 VAC coming from standard wall outlets and is transformed to
9-11.1 VDC. Installing a 9 Volt battery provides battery backup during power outages. The power LED (green) will illuminate
when powered. The Versa’larm™is a multipurpose alarm panel that can be use in a variety of applications such as: septic
tanks, sumps, holding tanks, pump chambers, water tanks, flow, pressure, condensate, temperature, and any others where
a “dry contact” can be connected to the alarm panel.
When a switch (signaling device) contact “closes” the buzzer will annunciate, alarm LED (red) will illuminate, and the built in
auxiliary contacts will be activated. The signaling device could be a float switch, water sensor, or sump probe sensor. The
auxiliary contacts can be used to connect to an Alderon Industries Auto Dialer, an existing alarm security system, or building
automation system (BAS).
Pressing the “Alarm Silence” pushbutton will silence the buzzer and the alarm LED (red) remains on. When the alarm condi-
tion is cleared, the system automatically resets itself for the next alarm cycle.
Before proceeding with the installation or operation of the product, read all
instructions thoroughly, as well as complying with all federal, state and local
codes, regulations, and practices. The product must be installed by qualified
personnel familiar with all applicable local electrical and mechanical codes.
Refer to the National Electrical Code (NFPA 70). Failure to properly install and
test this product can result in personal injury or equipment malfunction.

Versa’larm™
Operation, Maintenance and Installation Manual
Installation of the Alarm Panel
1. To install/replace the battery for the backup power feature, remove the access cover (Fig. 1) and install 9 VDC battery
(Duracell model MX 1604B2 / Fig. 2). After installing battery, the green power LED should illuminate, then press and hold
the “Alarm Test” pushbutton (Fig. 3) to activate the alarm and make sure the battery is working properly. The buzzer should
annunciate and the alarm LED should illuminate. If using the auxiliary contacts, leave the access cover off until step 4 is
completed. If the auxiliary contacts are not used, replace the access cover (Fig. 4).
(Fig. 1) (Fig. 2) (Fig. 3) (Fig. 4)
2. Determine the mounting location for the alarm panel. Make sure power outlet (120 VAC, 50/60 Hz) is within 5-feet of the
alarm panel (Fig. 5). The power outlet should be on a separate circuit breaker from any other device and not on a switched
receptacle to maintain power integrity. Mount the alarm panel using two #6 self-tapping screws (not included / Fig. 6). Use
two #8 plastic anchors (not included / Fig. 7) if mounting the alarm panel to sheet rock.
(Fig. 5) (Fig. 6) (Fig. 7)
5 ft. Max
Alderon Industries - Hawley, MN | 218.483.3034 | [email protected] | alderonind.com
3. If auxiliary contacts are not used, go to step 6. If connecting alarm to an existing system, go to Figure 9 on page 3. If using
auxiliary contacts to connect to an Auto Dialer, refer to wiring diagram below (Fig. 8). When a signaling device such as a
float switch, water or sump sensor is activated, it will close relay contacts on Terminals 1A and 1B of the alarm panel which
activate the Auto Dialer. When connected, replace the access cover and pull wire(s) through the knockout(s) on the access
cover (see step 5). CAUTION! - Route all wires away from sharp objects and internal components when installing wires.
Terminals 1 and 2
Auto Dialer Power Supply
RED = “+”
BLACK = “-”
Terminals 3 and 4
Auto Dialer Contacts
YELLOW = 1A
WHITE = 1B
To Phone Line
+ - 1A
1A
(+) (-) (1A) (1B)
+-
1B
1B
(Fig. 8)
1-Zone Alarm - Model VA01A
Alarm Systems Control Panels Float Switches Leak Detection Systems Page 2 of 4P/N: 101444

Versa’larm™
Operation, Maintenance and Installation Manual
Alderon Industries - Hawley, MN | 218.483.3034 | [email protected] | alderonind.com
Installation of the Alarm Panel Continued
4. If connecting to an existing alarm security system or building automation system (BAS), leave Terminals “+” and “-” open
and use 18 gauge 2-conductor wire to connect the existing product to Terminals 1A and 1B (Fig. 9). When connected,
replace the access cover and pull wire(s) through the knockout(s) on the access cover (see step 5). CAUTION! - Route all
wires away from sharp objects and internal components when installing wires.
AUXILIARY CONTACTS: (Fig. 9)
Terminals “+” and “-”
11.1 VDC, 100mA power supply
for external equipment
Terminals 1A and 1B
Normally Open
Class 2, 24 VDC/VAC (50/60 Hz)
100 Milliamps Maximum
Note: The auxiliary contacts on Terminals 1A and 1B
of the alarm panel are Normally Open only.
+-
1A
5. After the access cover has been removed from the alarm panel (Fig. 10), use a needle nose pliers (not included) to
remove the desired “break away tabs” from the access cover, lightly pull and twist off tab(s) (Fig. 11). Replace the access
cover and run wire(s) through the knockout(s) (Fig. 12).
(Fig. 10) (Fig. 11) (Fig. 12)
6. Make note of the alarm condition(s) you are monitoring and keep them near the alarm panel.
1A
(1A) and (1B)
+-
1B
Building Automation System (BAS)
or
Another High Water Alarm
or
Any Monitoring System
1B
1-Zone Alarm - Model VA01A
Alarm Systems Control Panels Float Switches Leak Detection Systems Page 3 of 4P/N: 101444

Versa’larm™
Operation, Maintenance and Installation Manual
Alderon Industries - Hawley, MN | 218.483.3034 | [email protected] | alderonind.com
Installation of the Alarm Panel Continued
7. Connect any combination of switches (rated 9 VDC, 200mA Minimum) such as a float switch, water sensor, or sump probe
sensor to Terminals C and 1 on the terminal block of the alarm panel. TERMINAL 2 IS NEVER USED. See below for wiring
examples (Fig. 13). The alarm is activated by a “closed” switch. CAUTION! - When installing the “Signaling Device”, refer to
its installation instructions for proper installation.
8. Plug the alarm panel power supply into a 120 VAC, 50/60 Hz standard
wall outlet and the green “Power” LED should illuminate (Fig. 14).
Testing the Alarm Panel
(Fig. 13)
(Fig. 14)
Versa’larm™Accessory (P/N: 7933)
Indoor/Outdoor LED Strobe Beacon
Red C
Black 2
Use 18 gauge wire and connect Red Wire
to Terminal C and Black Wire to Terminal 2
TERMINALS C AND 1:
Float Switch
Black = 1
White = C
WaterSpotter™ or WaterSpotter™ Probe
Black = 1
Red = C
Combination of Sensors
Blacks = 1
Reds / Whites = C
1. Test the alarm panel by pressing and holding the “Alarm Test” pushbutton
(Fig. 15) or activating the “Signaling Device” (i.e., float switch or water
sensor / Fig. 16). The buzzer should annunciate and the alarm LED should
illuminate. Press the “Alarm Silence” pushbutton and the buzzer should
silence while the alarm LED remains on. After you remove pressure from
the “Alarm Test” pushbutton or deactivate the “Signaling Device”, the “Auto
Reset” feature reactivates the alarm panel for the next alarm cycle. If testing
with “Signaling Device”, make sure to test all devices for complete system
operation. Test product weekly to ensure system integrity.
(Fig. 15) (Fig. 16)
1-Zone Alarm - Model VA01A
5 ft. Max
Float Switch
White = C
Black = 1
X
Float Switch
White = C
Black = 1
WaterSpotter™
Red = C
Black = 1
X
Float Switch
White = C
Black = 1 WaterSpotter™
Red = C
Black = 1 WaterSpotter™ Probe
Red = C
Black = 1
X
Alarm Systems Control Panels Float Switches Leak Detection Systems Page 4 of 4P/N: 101444