VersAlarm™I/O - Features
1Power On Indicator - Green LEDs illuminate enclosure cover
2Alarm Beacon - Red LEDs illuminate enclosure cover
3Alarm Buzzer - Annunciates to indicate an alarm condition
4Test/Silence Pushbutton - Activates alarm, silences alarm buzzer
5Auxiliary Contacts - Interface with external device, 24VDC @ 0.5A maximum
6Sensor Input - Terminals for the alarm oat switch connection
7Power Mains Input - Terminals for line connections (L1/L2), 230VAC
8 Power Indicator Turn Off - Hold test/silence pushbutton for 15 seconds
9 QR Code - Scan code for additional product information (alderonind.com)
10 Sound Chamber - Maximum output from buzzer, protects from water intrusion
11 Cable Grips (not shown) - Pre-installed for easy installation
12 6-Foot Power Cable (not shown) - Pre-installed, male, 230VAC
13 Alarm Float Switch/Sensor (not shown) - Pre-installed for easy installation
Step 5: Install Bottom Cover
Line up the bottom enclosure cover with the grooves (5A), then slide
directly upward (5B) until it meets the top of the enclosure so the screw
hole is lined up and replace the screw at the bottom of enclosure.
Step 6: Power Alarm and Quick Test
After all wiring and installation steps have been completed, power the
alarm by plugging the pre-installed power cable into a standard 230VAC
wall outlet or power receptacle. Make sure the outlet is on a separate
circuit breaker from any other device and not on a switched receptacle
to maintain power integrity. Use the features list and diagram below to
perform a quick test of the alarm to make sure it is working properly.
Note: For complete wiring, installation instructions, or troubleshooting,
refer to the user guide for this model by scanning QR code.
5A
5B
8
9
10
1 2
3
4
57
6
Included with Product
Customer Support
Specications
▪ (1) VersAlarm™ I/O alarm panel
▪ (2) Pre-installed cable grips
▪ (1) Pre-installed, male, 230VAC, 6-foot power cable
▪ (1) Pre-installed alarm float switch
▪ (1) RubberLox™ pipe clamp
▪ (1) Wago connector
Online
alderonind.com
Email
QR Code
Scan code for full product details
Primary Power: 230VAC, 50/60Hz
Power: 2.64 Watts maximum (alarm condition)
Certifications: FCC Part 15 (US/Canada), CSA (US/Canada)
Auxiliary Contacts: 24VDC @ 0.5 Amps maximum
Enclosure: Outdoor, rated Type 3R
FCC Part 15: NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
inter ference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
inter ference by one or more of the following measures: increase the separation between the equipment and receiver, connect the equipment into an
outlet on a circuit different from that to which the receiver is connected, consult the dealer or an experienced radio/TV technician for help. Caution:
changes / modications not approved by Alderon Industries could void the user’s authority to operate the equipment.
VersAlarm™ I/O
Electrical: 5 Amp, 120/240VAC
Operating Temperature: 0 - 140° F
Cable Type:
SJOOW (UL/CSA), flexible, 18 gauge, 2-conductor, water/oil resistant
Float Housing: Polypropylene
Switching Differential: 20° total (narrow angle) and 90° total (wide angle)
Switching Configuration: Single Pole, Single Throw (Normally Open or Normally Closed)
Certifications: CSA (US and Canada)
Altra™ Alarm Float Switch
