Alemlube S Series User manual

Description
With covers manufactured from high quality impact resistant and UV stabilised polypropylene and a positive latching mechanism that
automatically locks hose at the desired length, the new S Series of plastic hose reels from Alemlube will provide you with a reliable
& cost effective means of storing and retrieving hose assemblies in your workshop or garden. The reels can be floor, ceiling or wall
mounted & the detachable mounting bracket facilitates ease of reel mounting & storage.
Specifications
Operation
1 Check your S Series reel for correct operation by slowly pulling out the hose.
A clicking noise will be heard every half revolution of the drum.
2 Latching mode switch, when your S Series reel is in free run state, pull out
the hose and allow it to retract after hearing the first, second or third click.
3 To unlatch the reel, slowly pull out the hose until the clicking noise stops, and
then let the hose retract unitl the hose stop rests against the hose guide.
4 NOTE: To avoid damage to your S Series reel, always hold onto the hose while it is rewinding. Periodically check the hose
condition for wear or damage and check the swivel fitting for leakage. Replace any worn, damaged or leaking parts.
Warning
1 Make sure incoming line pressure does not exceed the rated operating pressure for your model hose reel.
2 Use proper eye protection when assembling and using the hose reel.
3 Use soap and water when checking for leaks.
4 Keep children away from the work area.
Installation Of Reel
1 For overhead ceiling mounting: install reel at most, 3 metres
above the floor.
2 You will need to purchase appropriate hardware for the
mounting of your new reel.
3 The reel base has four 7mm (11/16”) drilled holes for
mounting on a suitable flat surface. Figure 2 is a
template showing the correct location of the 4 mounting
holes in the base.
4 Using the three holes in the base, mount the reel in the
desired location. Be sure to use appropriate hardware and to
tighten the reel securely to the mounting location.
5 Apply Teflon tape or pipe sealant to the outlet fitting on the
hose & then attach to desired tool or nozzle. Check
connection for any leakage & check the reel for correct
operation. See operation section. If hose stop adjustment is
required, pull hose from reel and allow the reel to latch at the
desired length. Loosen hose stop bolts and slide hose stop to
a position close to the hose guide. Tighten hose stop bolts
and unlatch the reel.
Uses/Pressure Air and Water. Max. operating pressure: Air Reels: 290 psi Water Reel: 145 psi
Hose Lengths SA300 – 18m x 10mm ID hose. SA400 – 15m x 12mm ID hose.
Materials Plastic covers, steel spring & Buna “N” seals
Pressure SA300, SA400 – 290 psi (20 bar)
Weight/Dimensions 10kg / 490mm (L) x 448mm (H) x 228mm (W)
Inlet/Outlet SA300 – 1/4” BSPT(f)/1/4” BSPT(m)
SA400 – 1/2” BSPT(f)/1/2” BSPT(m)
Working Temp 0°C– 50°C
Visit our website at www.alemlube.com.au or www.alemlube.co.nz
NSW
TEL: [phone]
FAX: [phone]
QLD/PNG
TEL: [phone]
FAX: [phone]
VIC/TAS
TEL: [phone]
FAX: [phone]
WA
TEL: [phone]
FAX: [phone]
SA/NT
TEL: [phone]
FAX: [phone]
NZ
TEL: [phone]
FAX: [phone]
S Series Hose Reels
SA300
SA400
OWNER’S TECHNICAL MANUAL
All manuals and user guides at all-guides.com
all-guides.com

Item No. Part No. Description QTY Item No. Part No. Description QTY
1 SA300-1 Screw ST4.8x13 F 8 21 SA300-21 Swivel Assembly 1
2 SA300-2 Clip for Ratchet 121A SA400-21 Swivel Assembly 1
2A SA300-2-7-9-10-20 Rachet Assembly 121B SW500-21 Swivel Assembly 1
3 SA300-3 Screw ST4.2x16 F 822 SA300-22 Cover for Spool 1
4 SA300-4 Small Cover 1 23 SA300-23 Screw M5x12 2
5SA300-5 Cover for Axle 1 24 SA300-24 Inlet Hose Assembly 1
6SA300-6 Screw ST2.9x13 F 2 24A SA400-24 Inlet Hose Assembly 1
7SA300-7 Ratchet 1 24B SW500-24 Inlet Hose Assembly 1
8SA300-8 Ratchet Ring 225 SA300-25 Screw M4x10 10
9SA300-9 Ratchet Spring 126 SA300-26 Spring Clamp 1
10 SA300-10 Screw ST3.5x13 C 327-1 SA300-27-1 Screw M6x40 2
11 SA300-11 Hose Assembly 127-2 SA300-27-2 Washer 8 2
11A SA400-11 Hose Assembly 127-3 SA300-27-3 Hose Stopper 1
11B SW500-11 Hose Assembly 1 27-3A SA400-27-3 Hose Stopper 1
12 SA300-12 Bracket 1 27-3B SW500-27-3 Hose Stopper 1
13 SA300-13 Stator 1 27-4 SA300-27-4 Nut 2
14 SA300-14 Axle 1 28 SA300-28 Tube Fitting 1
15 SA300-15 Stator 2 29 SA300-29 Guide Protector 1
16 SA300-16 Screw ST4.87x75 C 330 SA300-30 Washer 3 3
17 SA300-17 Main Spring 1 31 SA300-31 Drum 2
18 SA300-18 Cover 2 32 SA300-32 Main Axle 1
19 SA300-19 Nut M4 10 33 SA300-33 Washer 4 1
20 SA300-20 Big Cover 1 34 SA300-34 Screw ST2.9x9.5C 1
2
Parts and Drawing Breakdown For S Series Hose Reels
Ordering Spare Parts SA300/SA400/SW500 Spare Parts List
NSW
TEL: [phone]
FAX: [phone]
QLD/PNG
TEL: [phone]
FAX: [phone]
VIC/TAS
TEL: [phone]
FAX: [phone]
WA
TEL: [phone]
FAX: [phone]
SA/NT
TEL: [phone]
FAX: [phone]
NZ
TEL: [phone]
FAX: [phone]
Visit our website at www.alemlube.com.au or www.alemlube.co.nz
All manuals and user guides at all-guides.com