Allen-Bradley Micro800 User manual

Installation Instructions
Micro800 Remote LCD
Catalog Number 2080-REMLCD
http://rockwellautomation.com/literature
FR
Cette publication est disponible en français
sous forme électronique (fichier PDF). Pour la
télécharger, rendez-vous sur la page Internet
indiquée ci-dessus.
PT
Esta publicação está disponível em portugués
como PDF. Vá ao endereço web que aparece
acima para encontrar e fazer download da
publicação.
IT Questa pubblicazione è disponibile in
Italiano in formato PDF. Per scaricarla
collegarsi al sito Web indicato sopra. ZH
DE
Diese Publikation ist als PDF auf Deutsch
verfügbar. Gehen Sie auf die oben genannte
Web-Adresse, um nach der Publikation zu
suchen und sie herunterzuladen.
ZC
ES
Esta publicación está disponible en español
como PDF. Diríjase a la dirección web
indicada arriba para buscar y descarga esta
publicación.
KO
Table of Contents
Topic Page
Important User Information 2
North American Hazardous Location Approval 4
Additional Resources 6
Overview 7
Additional Resources 6
Install the Micro800 Remote LCD 9
Mount the Module 10
RS232 Port 16
USB Port 16
Connect Power 14
Specifications 18

2Micro800 Remote LCD
Rockwell Automation Publication 2080-IN010B-EN-P – May 2015
Important User Information
Solid state equipment has operational characteristics differing from those of electromechanical equipment. Safety Guidelines
for the Application, Installation and Maintenance of Solid State Controls (Publication SGI-1.1 available from your local Rockwell
Automation sales office or online at http://rockwellautomation.com/literature) describes some important differences between
solid state equipment and hard-wired electromechanical devices. Because of this difference, and also because of the wide
variety of uses for solid state equipment, all persons responsible for applying this equipment must satisfy themselves that each
intended application of this equipment is acceptable.
In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages resulting from the use
or application of this equipment.
The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and
requirements associated with any particular installation, Rockwell Automation, Inc. cannot assume responsibility or liability for
actual use based on the examples and diagrams.
No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, equipment, or software
described in this manual.
Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell Automation, Inc., is
prohibited.
Throughout this manual, when necessary, we use notes to make you aware of safety considerations.
WARNING: Identifies information about practices or circumstances that can cause an explosion in a
hazardous environment, which may lead to personal injury or death, property damage, or economic loss.
ATTENTION: Identifies information about practices or circumstances that can lead to personal injury or
death, property damage, or economic loss. Attentions help you identify a hazard, avoid a hazard and
recognize the consequences.
SHOCK HAZARD: Labels may be on or inside the equipment (for example, drive or motor) to alert people
that dangerous voltage may be present.
BURN HAZARD: Labels may be on or inside the equipment (for example, drive or motor) to alert people
that surfaces may reach dangerous temperatures.
IMPORTANT
IMPORTANT: Identifies information that is critical for successful application and understanding of the
product.

Micro800 Remote LCD 3
Rockwell Automation Publication 2080-IN010B-EN-P – May 2015
Environment and Enclosure
Prevent Electrostatic Discharge
ATTENTION: This equipment is intended for use in a Pollution Degree 2
industrial environment, in overvoltage Category II applications (as defined in IEC
60664-1), at altitudes up to 2000 m (6562 ft) without derating.
This equipment is not intended for use in residential environments and may not
provide adequate protection to radio communication services in such
environments.
This equipment is supplied as open-type equipment. It must be mounted within
an enclosure that is suitably designed for those specific environmental
conditions that will be present and appropriately designed to prevent personal
injury resulting from accessibility to live parts. The enclosure must have suitable
flame-retardant properties to prevent or minimize the spread of flame,
complying with a flame spread rating of 5VA or be approved for the application if
nonmetallic. The interior of the enclosure must be accessible only by the use of
a tool. Subsequent sections of this publication may contain additional
information regarding specific enclosure type ratings that are required to comply
with certain product safety certifications.
In addition to this publication, see:
• Industrial Automation Wiring and Grounding Guidelines, Rockwell
Automation publication 1770-4.1, for additional installation requirements.
• NEMA Standard 250 and IEC 60529, as applicable, for explanations of the
degrees of protection provided by different types of enclosure.
ATTENTION: This equipment is sensitive to electrostatic discharge, which can
cause internal damage and affect normal operation. Follow these guidelines
when you handle this equipment:
• Touch a grounded object to discharge potential static.
• Wear an approved grounding wriststrap.
• Do not touch connectors or pins on component boards.
• Do not touch circuit components inside the equipment.
• Use a static-safe workstation, if available.
• Store the equipment in appropriate static-safe packaging when not in use.

4Micro800 Remote LCD
Rockwell Automation Publication 2080-IN010B-EN-P – May 2015
North American Hazardous Location Approval
The following modules are North American Hazardous Location approved: 2080-REMLCD.
The following information applies when
operating this equipment in hazardous
locations:
Informations sur l’utilisation de cet
équipement en environnements
dangereux:
Products marked "CL I, DIV 2, GP A, B, C, D" are
suitable for use in Class I Division 2 Groups A, B,
C, D, Hazardous Locations and nonhazardous
locations only. Each product is supplied with
markings on the rating nameplate indicating the
hazardous location temperature code. When
combining products within a system, the most
adverse temperature code (lowest "T" number)
may be used to help determine the overall
temperature code of the system. Combinations
of equipment in your system are subject to
investigation by the local Authority Having
Jurisdiction at the time of installation.
Les produits marqués "CL I, DIV 2, GP A, B, C,
D" ne conviennent qu'à une utilisation en
environnements de Classe I Division 2 Groupes
A, B, C, D dangereux et non dangereux.
Chaque produit est livré avec des marquages
sur sa plaque d'identification qui indiquent le
code de température pour les environnements
dangereux. Lorsque plusieurs produits sont
combinés dans un système, le code de
température le plus défavorable (code de
température le plus faible) peut être utilisé
pour déterminer le code de température global
du système. Les combinaisons d'équipements
dans le système sont sujettes à inspection par
les autorités locales qualifiées au moment de
l'installation.
WARNING: EXPLOSION
HAZARD
• Do not disconnect equipment
unless power has been removed or
the area is known to be
nonhazardous.
• Do not disconnect connections to
this equipment unless power has
been removed or the area is known
to be nonhazardous. Secure any
external connections that mate to
this equipment by using screws,
sliding latches, threaded
connectors, or other means
provided with this product.
• Substitution of any component may
impair suitability for Class I,
Division 2.
• If this product contains batteries,
they must only be changed in an
area known to be nonhazardous.
WARNING: RISQUE
D’EXPLOSION
• Couper le courant ou s'assurer
que l'environnement est classé
non dangereux avant de
débrancher l'équipement.
• Couper le courant ou s'assurer
que l'environnement est classé
non dangereux avant de
débrancher les connecteurs. Fixer
tous les connecteurs externes
reliés à cet équipement à l'aide
de vis, loquets coulissants,
connecteurs filetés ou autres
moyens fournis avec ce produit.
• La substitution de tout composant
peut rendre cet équipement
inadapté à une utilisation en
environnement de Classe I,
Division 2.
• S'assurer que l'environnement est
classé non dangereux avant de
changer les piles.

Micro800 Remote LCD 5
Rockwell Automation Publication 2080-IN010B-EN-P – May 2015
• Make sure all connectors are securely tightened to properly seal the
connections against leaks and maintain IP enclosure type requirements.
• The USB port is intended for temporary local programming purposes only and
not intended for permanent connection.
• The USB cable is not to exceed 3.0 m (9.84 ft) and must not contain hubs.
• The RS232 and Power cables are not to exceed 3.0 m (9.84 ft).
• Do not place the module in direct sunlight. Prolonged exposure to sunlight may
degrade the LCD.
• The USB cap must be in place to maintain IP65 rating.
• If you connect or disconnect the RS232 cable with power applied to this module
or the serial device on the other end of the cable, an electrical arc can occur.
This could cause an explosion in hazardous location installations.
Be sure that power is removed or the area is nonhazardous before proceeding.
• If you connect or disconnect the communications cable with power applied to
this module or any device on the network, an electrical arc can occur. This could
cause an explosion in hazardous location installations.
Be sure that power is removed or the area is nonhazardous before proceeding.
• When used in a Class I, Division 2, hazardous location, this equipment must be
mounted in a suitable enclosure with proper wiring method that complies with
the governing electrical codes.
• The USB port is intended for temporary local programming purposes only and
not intended for permanent connection. If you connect or disconnect the USB
cable with power applied to this module or any device on the USB network, an
electrical arc can occur. This could cause an explosion in hazardous location
installations.
Be sure that power is removed or the area is nonhazardous before proceeding.
• Do not connect directly to line voltage. Line voltage must be supplied by a
suitable, approved isolating transformer or power supply having short circuit
capacity not exceeding 100V A maximum or equivalent.
• Do not use the USB port in hazardous locations.

6Micro800 Remote LCD
Rockwell Automation Publication 2080-IN010B-EN-P – May 2015
Additional Resources
If you would like a manual, you can:
• download a free electronic version from the Internet:
http://rockwellautomation.com/literature
• purchase a printed manual by contacting your local Allen-Bradley distributor or
Rockwell Automation representative
Resource Description
Micro820 20-point Programmable
Controllers User Manual, publication
2080-UM005
A more detailed description of how to install and use your
Micro820 programmable controller.
Micro800 Plug-in Modules and Accessories
User Manual, publication 2080-UM004 Installation and wiring descriptions for the different Micro800
plug-in modules and accessories.
Micro820 Programmable Controllers
Installation Instructions, publication
2080-IN009
Information on how to install your Micro820
programmable controller.
Micro800 AC Power Supply Installation
Instructions, publication 2080-IN001 Information on wiring and installing the optional AC power supply.
Industrial Automation Wiring and
Grounding Guidelines, publication 1770-4.1 More information on proper wiring and grounding techniques.

Micro800 Remote LCD 7
Rockwell Automation Publication 2080-IN010B-EN-P – May 2015
Overview
The Micro800™ Remote LCD is a simple IP65 text display interface that allows configuration of
such settings as IP address on the Micro800 controller. It is an accessory to the Micro820
controller.
The remote LCD can be connected to the controller through an RS232 port. It can be mounted
through the front panel or on the same DIN rail as the controller.
Micro800 Remote LCD Overview
2080-REMLCD Description
Description Description
1 Logo casing(1)
(1) The module is shipped with the Allen-Bradley sticker label but you can customize the space with your
product logo. Dimensions for the logo casing and the sticker label are shown below.
6 DIN rail latch
2 Display screen 7 USB port
3 Function keys 8 RS232 port
4 Arrow keys 9 24V DC power port
5 ESC and OK keys
OK
ESC
F4 F5
F1 F2 F3
F6
MENU
34567
1
68
Front Back
9
2
37
5
1
Sticker label
36.70
4.70
Sticker casing
Measurements are in millimeters.

8Micro800 Remote LCD
Rockwell Automation Publication 2080-IN010B-EN-P – May 2015
Module Dimensions
ATTENTION: The length of RS232 and 24V DC power cable connection
to the 2080-REMLCD module must not exceed 3 m (9.84 ft.).
Catalog Number Height (a) Width (b) Depth (c)
2080-REMLCD 97 mm (3.82 in.) 130 (5.11 in.) 35.5 (1.40 in.)
OK
ESC
F4 F5
F1 F2 F3
F6
MENU
46258
RS232 and 24V DC power cable
connections must not exceed 3 m.
Micro820
controller Micro800
REMLCD
Power
supply
OK
ESC
F4 F5
F1 F2 F3
F6
MENU
a
bc

Micro800 Remote LCD 9
Rockwell Automation Publication 2080-IN010B-EN-P – May 2015
Parts List
The Micro800 Remote LCD module ships with these items:
•Allen-Bradley sticker label
•Clamp accessories for panel mounting (4 pcs)
•Product Information (publication 2080-PC002)
Install the Micro800 Remote LCD
Before installing the Remote LCD through the front panel, review minimum clearances, panel
guidelines, panel cutout dimensions, and product dimensions.
Minimum Spacing
Maintain spacing from objects such as enclosure walls, wireways, and adjacent equipment. Allow
50.8 mm (2.0 in.) of space on all sides for adequate ventilation. If optional accessories/modules
are attached such as the optional power supply, 2080-PS120-240VAC, make sure that there is
50.8 mm (2.0 in.) of space on all sides after attaching the optional parts.
Plan for adequate space around the module, inside the enclosure, for ventilation and cabling.
Consider heat produced by other devices in the enclosure. The ambient temperature around the
module must be -20…50 °C (-4…122 °F).
Panel Guidelines
Supporting panels must be at least 16 gauge to provide proper sealing against water and dust and
to provide proper support. The panel surface must be flat and free of imperfections to maintain
an adequate seal and NEMA/IP Type ratings.
IMPORTANT
Most applications require installation in an industrial enclosure to
reduce the effects of electrical interference and environmental
exposure. Locate your device as far as possible from power lines, load
lines, and other sources of electrical noise such as hard-contact
switches, relays, and AC motor drives. For more information on proper
grounding guidelines, see the Industrial Automation Wiring and
Grounding Guidelines, publication 1770-4.1.
TIP
The minimum spacing requirements are sufficient for connecting cables and inserting.
Plan for additional clearance if using the USB host port on the back of the unit.

10 Micro800 Remote LCD
Rockwell Automation Publication 2080-IN010B-EN-P – May 2015
Panel Cutout Dimensions
You can print the panel cutout template that comes at the end of this installation instructions.
Panel cutout dimensions are provided in the next table.
Mount the Module
There are two ways to mount the Micro800 Remote LCD, as described in the following sections:
•Mount the Module in a Panel
•Mount the Module on a DIN Rail
Catalog Number Height, Approx., mm (inches) Width, Approx., mm (inches)
2080-REMLCD 88.5 ± 0.5 (3.48 ± 0.02) 121.5 ± 0.5 (4.78 ± 0.02)
ATTENTION: Disconnect all electrical power from the panel before
making the panel cutout.
•Make sure the area around the panel cutout is clear.
•Take precautions so metal cuttings do not enter any components
already installed in the panel.
•Failure to follow these instructions may result in personal injury or
damage to panel components.
WARNING: If you connect or disconnect the RS232 cable with power
applied to this module or the RS232 device on the other end of the
cable, an electrical arc can occur. This could cause an explosion in
hazardous location installations.
Be sure that power is removed or the area is nonhazardous before
proceeding.
WARNING: When used in a Class I, Division 2, hazardous location, this
equipment must be mounted in a suitable enclosure with proper wiring
method that complies with the governing electrical codes.