Allen-Bradley 198E-C2S4 User manual

Plastic Enclosure for DOL Starter -Application Instruction
ATTENTION:
To prevent electrical shock, disconnect from power source before installing or servicing. To be commis-
sioned and maintained only by qualied personnel; pay attention to the operating instructions!
The opening of the branch circuit protective device may be an indication that a fault current has been
interrupted. To reduce the risk of re or electric shock, current-carrying parts and other components of
the starter should be examined and replaced if damaged.
When wired for 2-wire control, a motor connected to the circuit may start automatically when the over-
load relay is in the automatic reset position.
When wired for 2-wire control, a motor connected to the circuit may start when a person actuates the
RESET push button.
Kunststogehäuse für DOL-Starter -Anwendungsanweisung
ACHTUNG:
Vor Installations- oder Servicearbeiten Stromversorgung unterbrechen, um Unfälle zu vermeiden.
Inbetriebsetzung und Wartung nur durch Fachpersonal; Betriebsanleitung beachten!
Das Ansprechen eines Schutzgeräts kann auf einen aufgetretenen Kurzschluss hinweisen. Um Risiken wie
Feuer oder Stromschlag zu vermeiden sollten die Starterkomponenten überprüft und gegebenenfalls
ersetzt werden.
Bei Startern mit Dauerkontaktsteuerung kann ein Motor automatisch starten, wenn das Motorschutzrelais
auf automatische Rückstellung eingestellt ist.
Bei Startern mit Dauerkontaktsteuerung kann ein Motor automatisch starten, wenn nach einer Auslösung
des Motorschutzrelais die Rückstelltaste betätigt wird.
Boîtier plastique pour démarreur direct - Notice d´application
ATTENTION:
Avant le montage et la mise en service, couper l'alimentation secteur an d'éviter tout accident. Mise en
service et entretien: seulement par du personnel spécialisé; respecter les instructions d'exploitation!
Le déclenchement d'un dispositif de protection peut indiquer qu'un court-circuit s'est produit. Pour éviter
des risques tels qu'un incendie ou un choc électrique, les éléments du démarreur devraient être contrôlés
et remplacés si nécessaire.
Si la commande de démarrage est réalisée avec un contact permanent, le moteur peut démarrer automa-
tiquement lorsque le relais de surcharge est en mode de réarmement automatique.
Si la commande de démarrage est réalisée avec un contact permanent, le moteur peut démarrer lorsque,
après déclenchement du relais de surcharge, le bouton de réinitialisation est actionné.
Custodie plasitce per avviatore diretto - Istruzione d'applicazione
ATTENZIONE:
Per prevenire infortuni, togliere tensione prima dell'installazione o manutenzione. Messa in servizio e
manutenzione devono essere eettuate solo da personale specializzato; attenersi alle istruzioni per l'eser-
cizio!
L'intervento di un dispositivo di protezione può indicare che si è vericato un corto circuito. Per evitare
rischi, quali incendi o scosse elettriche, i componenti dell'avviatore dovrebbero essere controllati e sosti-
tuiti se necessario.
Quando collegato con controllo a due li, il motore connesso al circuito può avviarsi automaticamente se
il relè è impostato su reset automatico.
Quando collegato con controllo a due li, il motore connesso al circuito può avviarsi automaticamente se
il pulsante di RESET del relè di sovraccarico viene premuto.
Cofre en plástico para arrancador directo - Instrucciones de montaje
ATENCIÓN:
Desconectar la alimentación eléctrica antes de realizar el montaje, con el objeto de evitar accidentes. La
puesta en servicio y el mantenimiento ha de realizarse exclusivamente por personal especializado;
¡prestar atención a las instrucciones de montaje y puesta en marcha!
El disparo de un dispositivo de protección puede indicar que se ha producido un cortocircuito. Para evitar
riesgos como incendio o descargas eléctricas, los componentes del arrancador deben ser examinados y
reemplazados si fuera necesario.
Cuando el sistema de control es por contacto permanente, el motor se puede conectar automáticamente
si el relé de sobrecarga tiene ajustado el rearme en posición de automático.
Cuando el sistema de control es por contacto permanente, después del disparo del relé térmico, el motor
se puede conectar cuando se presiona el pulsador de RESET (rearme).
198E-C2S4
IEC / EN 62208
IEC / EN 60947-4-1
UL 508
CSA 22.2, No. 14

Assembly of Direct On-line Starters
321
54
Attach the overload relay to the contactor Snap the starter combination
onto the device support
Snap the 800F contact blocks onto the
device support:
•Pos. 1 (left): N.O. contact
•Pos. 2 (right): N.C. contact
Snap the side-mount auxiliary contact
to the right side of the contactor.
Do the control wiring according the wiring diagram / wire table.
Mount the 800F push button operators into the cover.
Screw down the device
support into the enclosure
(2)

Impulse Control
Multi Function Push Button
3-phase 2-phase Single-phase Maintained Control
O - I Selector Switch
CAUTION:
BONDING BETWEEN METALLIC
CONDUITS MUST BE PROVIDED.
ATTENTION:
UNE LIAISON ÉLECTRIQUE
DOIT ÊTRE ASSURÉE ENTRE
LES CONDUITS MÉTALLIQUES
SUPPLY CONDUCTOR
SIZE (AWG)
BONDING CONDUCTOR
QTY. SIZE
FOR USE WITH ALLEN-BRADLEY
GROUNDING ADAPTER KIT, CAT. NO. 198-GR1
SEE APPLICABLE CODES AND LAW
FOR GROUNDING REQUIREMENTS
14
12
10
14
12
12
1
1
2
Wiring Tables
Impulse Control
From To Length [mm]
K1M - A2 ( N ) 280
K1M - 13 100
S1 - 13 140
S1 - 31 100
K1M - 14 140
F2 - 95 S1 - 32 140
S1 - 14
K1M - A1
Component Selection for Three-Phase Motor Starters
Contactors 100-C and Overload Relays 193-ED / 193-EE
Current Range
230V
50Hz
400V
50Hz
500V
50Hz
690V
50Hz
200V
60Hz
230V
60Hz
460V
60Hz
575V
60Hz
100kA,
690V
100kA,
600V Components
Min
[A] [kW] [kW] [kW] [kW] [HP] [HP] [HP] [HP]
Max
[A]
DIN Fuses
Type gL/gG
Max. Fuse
Class CC, J Contactor
Overload
Relay
9 35 10 15 15 11...15 7 1/2 10 20 25 63 50 100-C30 00 193-ED1FD
9 38 11 18.5 18.5...20 18.5 10 10 25 30 63 50 100-C37 00 193-ED1FD
9 44 13 20...22 22...25 22 10 15 30 30 80 70 100-C43 00 193-ED1FD
To complete the cat. no., please replace with a coil voltage code.
The electronic overload relay 193-EE* can be taken as well.
Contactors 100-C and Single-Phase Overload Relays 193S-EE
Current Range
230V
50Hz
115V
60Hz
200V
60Hz
230V
60Hz
100kA,
690V
100kA,
600V Components
Min
[A]
Max ]PH[]PH[
]PH[
]Wk[
]A[
DIN Fuses
Type gL/gG
Max. Fuse
Class CC, J Contactor
Overload
Relay
9 35 5.5 1 1/2...2 3 5 63 50 100-C30 00 193S-EETD
9 38 5.5 3 5 5 63 50 100-C37 00 193S-EETD
9 44 535.5 7 1/2 63 60 100-C43 00 193S-EETD
To complete the cat. no., please replace with a coil voltage code.
Component Selection for Single-Phase Motor Starters
Additional components
Schematic Diagram
Maintained Control
From To Length [mm]
K1M - A2
K1M - A1
S1 - 14
( N ) 280
S1 - 13 140
F2 - 95 140
ytitnauQderiuqeRnoitpircseD
Neutral Terminal
Cat. No.
Control Components required for Impulse Control
1
1
snoitangiseDlanimreTecneuqeShtiwgnitnuoMediSrofskcolBtcatnoCyrailixuA 100-SB10
198E-PNT
1O-IsgnikraM,snoitcnuF2,rotarepOnottuBhsuPnoitcnuF-itluM 800FP-U2EFFE
Base Mounted Contact Block 1 N.C. 1 800F-BX01
Base Mounted Contact Block 1 N.O. 1 800F-BX10
Reset Push Button Operator, Marking "R" 1 800FP-F611
Control Components required for Maintained Control
Selector Switch Operator, non-illuminated, 2-position 1 800FP-SM22
Base Mounted Contact Block 1 N.O. 1 800F-BX10
Reset Push Button Operator, Marking "R" 1 800FP-F611
1
2
2
2
2
1
1
Add wires for common control. Remove if separate control is required.
(3)
¥
¥ For UL applications.
2
L1 Control voltage supplied from external source.
L1
1
96
95
97
98
L1
1
1
3
2
1
1- HAND
2- OFF
3- AUTO
A1
A2
2 WIRE
CONTROL
1 WHEN E-STOP IS USED
ILLUMINATED HOA SELECTOR SWITCH

Schematic Diagram for Direct On-line Starters with DeviceNet Communication
193-EDN193-EE DeviceNet
Dimensions
125 [4.93]
Ø23
[Ø0.91]
3.5
[0.14]
13 [0.51]
169 [6.66]
113.6 [4.48]
30 [1.18]
78 [3.07]
16 [0.63]
250 [9.85]
125 [4.93]
50 [1.97]
125 [4.93]
50 [1.97]
24 [0.95]
28.1 [1.11]
2 x 1...6 mm²
2 x No. 14...10 AWG
Pozidriv No. 2
2.3 Nm
20 lb-in
Pozidriv No. 2
2.0 Nm
18 lb-in
(1.2 x 6.5)
10
110 [4.33]
235 [9.26]
50 [1.97]
Rotary operator alternatively
(for maintained control)
DIR 10000401130 Version (01)
Printed in Estonia