Alliance Laundry Systems DRY725C_SVG User manual

User's Guide
for Dryers
DRY725C_SVG
Original Instructions
Keep These Instructions for Future Reference.
CAUTION: Read the instructions before using the machine.
(If this machine changes ownership, this manual must accompany machine.)
www.alliancelaundry.com
Part No. D514817ENR1
November 2017

WARNING
Risk of fire. Highly flammable material.
W881
Hazardous voltage inside. Disconnect power before servic-
ing.
Read all instructions before using unit.
WARNING
FOR YOUR SAFETY, the information in this manual
must be followed to minimize the risk of fire or explo-
sion or to prevent property damage, personal injury or
death.
W033
WARNING
• Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any oth-
er appliance.
• WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use
any phone in your building.
• Clear the room, building or area of all occu-
pants.
• Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s in-
structions.
• If you cannot reach your gas supplier, call the
fire department.
• Installation and service must be performed by a
qualified installer, service agency or the gas suppli-
er.
W052
IMPORTANT: Purchaser must consult the local gas sup-
plier for suggested instructions to be followed if the dryer
user smells gas. The gas utility instructions plus the
SAFETY and WARNING note directly above must be
posted in a prominent location near the dryer for cus-
tomer use.
WARNING
• Installation of unit must be performed by a quali-
fied installer.
• Install clothes dryer according to manufacturer’s
instructions and local codes.
• DO NOT install a clothes dryer with flexible plastic
venting materials. If flexible metal (foil type) duct is
installed, it must be of a specific type identified by
the appliance manufacturer as suitable for use with
clothes dryers. Refer to section on connecting ex-
haust system. Flexible venting materials are known
to collapse, be easily crushed, and trap lint. These
conditions will obstruct clothes dryer airflow and
increase the risk of fire.
W729R1
WARNING
To reduce the risk of severe injury or death, follow all
installation instructions. Save these instructions.
W894
WARNING
FOR YOUR SAFETY
Do not store or use gasoline or other flammable va-
pors and liquids in the vicinity of this or any other ap-
pliance.
W053
This product uses FreeRTOS V7.2.0 (www.freertos.org).
©Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
3 Part No. D514817ENR1

Table of Contents
Safety Information............................................................................. 6
Explanation of Safety Messages................................................................. 6
Important Safety Instructions....................................................................6
Restriction of hazardous substances (RoHS)...........................................8
Before Drying.................................................................................... 9
Energy Saving Tips....................................................................................9
Helps and Hints....................................................................................... 9
Sort......................................................................................................9
Load......................................................................................................9
Operating Your Dryer........................................................................ 11
Control Panel......................................................................................... 11
Digital Display....................................................................................... 12
Cycles..................................................................................................12
Auto-Sensing.................................................................................... 12
Manual............................................................................................. 12
Selections............................................................................................ 12
Temp................................................................................................ 12
Dryness............................................................................................12
Moisture Level....................................................................................12
Options................................................................................................13
Signal (on select models only)................................................................ 13
Status................................................................................................ 13
To Dry Clothes....................................................................................... 13
Optional Drying Rack...............................................................................14
Maintenance................................................................................... 15
Lubrication........................................................................................... 15
Care of Your Dryer.................................................................................. 15
Dryer Interior.....................................................................................15
Cabinet.............................................................................................15
Control Panel......................................................................................15
Exhaust System.................................................................................15
Motor Overload Protector........................................................................15
Lint Filter............................................................................................. 16
©Copyright 2017, Alliance Laundry Systems LLC
All rights reserved. No part of the contents of this book may be reproduced or transmied in any form or by any means without the expressed wrien
consent of the publisher.
©Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
4 Part No. D514817ENR1

Troubleshooting............................................................................... 17
Contact Information............................................................................... 19
©Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
5 Part No. D514817ENR1

Safety Information
Explanation of Safety Messages
Precautionary statements (“DANGER,” “WARNING,” and “CAU-
TION”), followed by specific instructions, are found in this manual
and on machine decals. These precautions are intended for the per-
sonal safety of the operator, user, servicer, and those maintaining
the machine.
DANGER
Indicates an imminently hazardous situation that, if
not avoided, will cause severe personal injury or
death.
WARNING
Indicates a hazardous situation that, if not avoided,
could cause severe personal injury or death.
CAUTION
Indicates a hazardous situation that, if not avoided,
may cause minor or moderate personal injury or prop-
erty damage.
Additional precautionary statements (“IMPORTANT” and “NOTE”)
are followed by specific instructions.
IMPORTANT: The word “IMPORTANT” is used to inform
the reader of specific procedures where minor machine
damage will occur if the procedure is not followed.
NOTE: The word “NOTE” is used to communicate in-
stallation, operation, maintenance or servicing informa-
tion that is important but not hazard related.
Important Safety Instructions
Save These Instructions
WARNING
To reduce the risk of fire, electric shock, serious injury
or death to persons when using your dryer, follow
these basic precautions:
W130
• Read all instructions before using the dryer.
• Install this dryer according to the INSTALLATION INSTRUC-
TIONS. Refer to the EARTH/GROUND INSTRUCTIONS in the IN-
STALLATION manual for the proper earth/ground connection of
the dryer. All connections for electrical power, earth/ground and
gas supply must comply with local codes and be made by li-
censed personnel when required. Do not do it yourself.
• Do not install or store the dryer where it will be exposed to wa-
ter and/or weather.
• Do not dry articles that have been previously cleaned in, washed
in, soaked in, or spoed with gasoline or machine oils, vegetable
or cooking oils, cleaning waxes or chemicals, dry-cleaning sol-
vents, thinner, anything containing chemicals such as in mops
and cleaning cloths, or other flammable or explosive substances
as they give off vapors that could ignite, explode or cause fabric
to catch on fire by itself.
• Items that have been soiled with substances such as cooking
oil, acetone, alcohol, petrol, kerosene, spot removers, turpentine,
waxes and wax removers, should be washed in hot water with an
extra amount of detergent before being dried in the tumble dry-
er.
• To reduce the risk of fire, DO NOT DRY plastics or articles con-
taining foam or latex rubber or similarly textured rubberlike ma-
terials, such as shower caps, water proof textiles, rubber-
backed articles, and clothes or pillows filled with foam rubber
pads.
• Do not tumble fiberglass curtains and draperies unless the label
says it can be done. If they are dried, wipe out the cylinder with
a damp cloth to remove particles of fiberglass.
• Do not allow children to play on or in the dryer. Close supervision
of children is necessary when the dryer is used near children.
This appliance is not intended for use by persons (including chil-
dren) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given
supervision or instruction concerning the use of the appliance
by a person responsible for their safety. This is a safety rule for
all appliances.
• Cleaning and user maintenance shall not be made by children
without supervision.
• Children less than three years should be kept away unless con-
tinuously supervised.
• Do not reach into the dryer if the cylinder is revolving.
• Use the dryer only for its intended purpose, drying clothes. AL-
WAYS follow the fabric care instructions supplied by the gar-
ment manufacturer and only use the dryer drum to dry textiles
that have been washed in water.
• Always read and follow manufacturer’s instructions on pack-
ages of laundry and cleaning aids. Heed all warnings or precau-
tions. To reduce the risk of poisoning or chemical burns, keep
them out of reach of children at all times (preferably in a locked
cabinet).
• Remove laundry immediately after the dryer stops.
Safety Information
©Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
6 Part No. D514817ENR1

• DO NOT operate the dryer if it is smoking, grinding or has miss-
ing or broken parts or removed guards and/or panels. DO NOT
tamper with the controls or bypass any safety devices.
• DO NOT operate individual units if they have been separated
from a stack unit.
• Dryer will not operate with the loading door open. DO NOT by-
pass the door safety switch by permiing the dryer to operate
with the door open. The dryer will stop tumbling when the door is
opened. Do not use the dryer if it does not stop tumbling when
the door is opened or starts tumbling without pressing the
START mechanism. Remove the dryer from use and call the
service person.
• ALWAYS clean the lint filter after every load. A layer of lint in
the filter reduces drying efficiency and prolongs drying time.
Keep area around the exhaust opening and adjacent surround-
ing area free from the accumulation of lint, dust and dirt. The
interior of the dryer and the exhaust duct should be cleaned pe-
riodically by qualified service personnel.
• Do not repair or replace any part of the dryer, or aempt any
servicing unless specifically recommended in the user-mainte-
nance instructions or in published user-repair instructions that
you understand and have the skills to carry out. ALWAYS dis-
connect the electrical power to the dryer before aempting
service. Disconnect the power cord by grasping the plug, not
the cord.
• If supply cord is damaged, it must be replaced by the manufac-
turer, its service agent or similarly qualified persons in order to
avoid a hazard.
• Before the dryer is removed from service or discarded, remove
the door to the drying compartment.
• Failure to install, maintain, and/or operate this machine accord-
ing to the manufacturer’s instructions may result in conditions
which can produce bodily injury and/or property damage.
NOTE: The WARNING and IMPORTANT SAFETY IN-
STRUCTIONS appearing in this manual are not meant to
cover all possible conditions and situations that may oc-
cur. Observe and be aware of other labels and precau-
tions that are located on the machine. They are intended
to provide instruction for safe use of the machine. Com-
mon sense, caution and care must be exercised when in-
stalling, maintaining, or operating the dryer.
Always contact your dealer, distributor, service agent or the manu-
facturer about any problems or conditions you do not understand.
Safety Information
©Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
7 Part No. D514817ENR1

Restriction of hazardous substances (RoHS)
Declaration of the Presence Condition of the Restricted Substan-
ces Marking
Restricted Substances and its chemical symbol
Part Name Lead
(Pb)
Mercury
(Hg)
Cadmium
(Cd)
Hexavalent
Chromium
(CR[VI])
Polybromina-
ted biphenyls
(PBB)
Polybromina-
ted diphenyl
ethers
(PBDE)
Printed Circuit Board - O O O O O
Electromechanical Parts O O - O O O
Cables and Wires O O O O O O
Metal Parts - O O O O O
Plastic Parts O O O O O O
Textile O O O O O O
Timing Belts O O O O O O
Display O O O O O O
O : Indicates that the percentage content of the restricted substance does not exceed the percentage of reference value of presence.
- : Indicates that the restricted substance corresponds to the exemption.
All parts named in this table with an “-” are in compliance with the European Union’s RoHS Legislation.
Restriction of hazardous substances (RoHS)
©Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
8 Part No. D514817ENR1

Before Drying
Energy Saving Tips
• Make sure the lint filter is always clean.
• Do not overload the dryer.
• Do not overdry items.
• Remove items to be ironed while still damp.
• Large loads of similar fabrics dry the most efficiently. However,
dry permanent press in smaller loads to prevent wrinkling.
• Use the correct cycle for the type of fabric being dried.
• Locate your dryer so the exhaust duct is as short and straight
as possible.
• Do not open the door during the drying cycle.
• Plan to do your laundry on low humidity days; your clothes will
dry faster.
• Dry multiple loads of clothes one right after another so dryer
interior does not have to be reheated for each load.
Helps and Hints
WARNING
To reduce the risk of fire, explosion, serious injury or
death, clothes which have traces of any flammable
substances such as cooking oil, machine oil, flamma-
ble chemicals, thinner, etc. must not be put into the
dryer.
W131
• The directions for installation and proper exhausting are given in
the Installation Instructions which are included with the dryer.
• Static electricity may cause garments of synthetic fibers (as
in lingerie) to cling together, especially if they are overdried. The
use of a liquid fabric softener in the rinse water of the washer,
or a fabric softener sheet in the dryer, will soften clothes and
reduce static electricity.
• Do not wash or dry clothes that shed lint in the same load with
permanent press or knit garments.
• Remove permanent press loads immediately after dryer stops.
• Follow the care labels on FLAME RETARDANT, SCOTCH-
GUARD™, etc., garments for proper washing and drying.
• If loads should be damp for ironing, use the Damp Dryness set-
ting, in an Automatic cycle.
Sort
If you have correctly sorted the items for washing, they should be
properly sorted for drying too.
1. Sort by color.
2. Separate lint shedding fabrics and lint receiving fabrics. Towels,
flannels, chenille, coons, rugs, etc., shed lint. Corduroys, knits
(including socks), permanent press, and synthetics aract lint.
3. Separate no heat, low heat and high heat items.
In any kind of drying, lightweight fabrics will dry faster than heavy-
weight fabrics. If mixed loads are dried together (such as sheets
and towels), remove the lighter weight fabrics when they are dry to
prevent overdrying and wrinkling. The best method is to dry clothes
which require the same time, temperature or dryness level in the
same load.
TLW1991N_SVG
Load
WARNING
Do not wash or dry items soiled with vegetable or
cooking oils. Some oils may remain after washing and
may cause the fabric to catch on fire by itself.
W527
• Do not overload your dryer. Bulk, not weight, determines the
load size. If the dryer is overloaded, it could cause discoloration
or permanent heat damage to the load.
• There should be space in the dryer for the clothes to tumble
freely and help to reduce wrinkles.
• Large and small pieces together make up loads which will tumble
well. Permanent press loads should be smaller to provide room
for tumbling. Proper tumbling allows for fewer wrinkles.
• A load can be too small. Just a few small pieces will not tumble
properly. They will take longer to dry and they may be wrinkled.
For small loads, add a couple of large towels or non lint shedding
items to aid in tumbling.
• The following illustrations show the ideal load sizes for fabrics.
The average load will fill the cylinder one third to half full when
wet.
Before Drying
©Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
9 Part No. D514817ENR1

Cylinder with wet linens and cottons
DRY2031N_SVG
Cylinder with wet permanent press items
DRY2032N_SVG
Before Drying
©Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
10 Part No. D514817ENR1

Operating Your Dryer
WARNING
To reduce the risk of fire, electric shock, serious injury
or death to persons, read the Safety Information sec-
tion before operating the dryer.
W520
Control Panel
DRY2670N_SVG
TLW2173N_SVG
Power/Cancel
TLW2174N_SVG
Start/Pause
DRY2547N_SVG
Regular
DRY2548N_SVG
Perm Press
DRY2549N_SVG
Delicate
DRY2551N_SVG
Time Dry
DRY2552N_SVG
Quick Dry
Table continues...
DRY2553N_SVG
Fluff Up
TLW2180N_SVG
Temp
TLW2181N_SVG
No Heat
DRY2556N_SVG
Low
TLW2183N_SVG
High
DRY2559N_SVG
Dryness
DRY2560N_SVG
Damp
DRY2562N_SVG
Near Dry
DRY2563N_SVG
Dry
DRY2564N_SVG
Moisture Level
DRY2565N_SVG
Sensing
DRY2566N_SVG
Wet
Table continues...
Operating Your Dryer
©Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
11 Part No. D514817ENR1

DRY2568N_SVG
Dry
TLW2192N_SVG
Signal (select models only)
DRY2574N_SVG
Door Open
DRY2547N_SVG
Heating
DRY2675N_SVG
Cooling
Digital Display
The two-digit display is used to show the time remaining in a cycle.
When the control is powered off, the right-most decimal in the dis-
play will flash every one to five minutes to indicate that the machine
is in Idle Mode.
The display also shows diagnostic codes.
Idle Mode
If no keypads have been pressed for five minutes after a cycle is
finished, the control will enter Idle Mode. A light in the lower right
corner of the digital display will flash every one to five minutes.
Press the Power/Cancel keypad to exit this mode and power the
display for cycle/option selection. This light will flash again after five
minutes when it re-enters Idle Mode.
Cycles
The following cycle descriptions will help determine which cycle to
choose depending on the type of laundry being dried. The cycle set-
tings may be modified using the Selections and Options.
Auto-Sensing
The Auto-Sensing drying cycle operation is determined by the type
of cycle selected as well as the moisture sensing system, which can
be set by changing the Dryness seing. Auto-Sensing cycles are
Energy Saver cycles that help prevent over-drying.
When a wet load is put into the dryer it takes a certain amount of
time to reach the desired dryness level. The time will vary with load
size, type of fabric, amount of moisture in the load, air flow and the
laundry room environment. The estimated time will be shown in the
digital display.
NOTE: The time shown before starting the cycle is esti-
mated by averaging the last 5 cycles run on the selected
cycle/dryness combination.
Cycle Use
Regular Use for sturdy items like play or
work clothes.
Perm Press Use for permanent press items
and synthetics.
Delicate Dry delicate items on this cycle.
Manual
There are three manual cycles: Time Dry, Quick Dry and Fluff Up.
These cycles will run for the set number of minutes shown on the
digital display. The cycle time can be increased or decreased using
the up and down arrow keypads. The time and temperature selec-
tion may be adjusted manually at any time before or during the cy-
cle.
Selections
The following selections can be used to modify the currently chosen
cycle. The default selections will be lit after choosing a cycle.
Temp
Press the Temp keypad to change a Manual cycle’s temperature.
Choose from No Heat, Low or High.
Dryness
Press the Dryness keypad to change the dryness level in an Auto-
Sensing cycle. Choose from Damp, Near Dry or Dry.
Damp Leaves load slightly damp for
easier ironing.
Near Dry Use for normal loads.
Dry Use for heavy items such as
blue jeans and blankets.
Over-drying can cause wrinkling, shrinking, excessive lint conditions,
and will use more energy than necessary. To increase energy savings
and to make sure loads are dried without over-drying, set your Au-
to-Sensing loads on Near Dry. If items are damp or over-dry at the
end of a cycle, increase or decrease the Dryness seing the next
time these loads are dried. Remember the seings that work best
to get ideal drying results.
Moisture Level
The Moisture Level status lights will be lit during an Auto-Sensing
cycle. The Sensing light will be lit at the beginning of the cycle.
The Wet and Dry lights will be lit based on readings from the mois-
ture sensing system.
Operating Your Dryer
©Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
12 Part No. D514817ENR1

Options
The following options can be used to modify the currently chosen
cycle.
Signal (on select models only)
Pressing the Signal keypad will change the end of cycle signal vol-
ume. There are four seings: Off, Low, Medium, High.
Status
The Status lights are lit during the cycle to show what part of the
cycle is running.
Door Open The Door Open status light is lit
any time that the dryer door is
open.
Heating The Heating status light is lit
to indicate that a heat portion
of the cycle is currently operat-
ing.
Cooling The Cooling status light is lit
during the cool-down portion of
the cycle.
NOTE: The Heating or Cooling status light flashes (1
second on/1 second off) during the warm-up period. The
status light stays lit until the motor starts running.
To Dry Clothes
IMPORTANT: Refer to the INSTALLATION INSTRUC-
TIONS before using dryer.
IMPORTANT: Before using dryer for the first time, use an
all-purpose cleaner or a detergent and water solution
and a damp cloth to remove shipping dust from inside of
dryer drum.
1. Sort items into separate loads.
NOTE: Remove all objects from pockets such as
lighters and matches.
TLW1991N_SVG
NOTE: Remove all sharp objects from laundry to
avoid tears and rips to items during normal machine
operation.
2. Clean lint filter.
DRY2757N_SVG
1
1. Lint Filter
Figure 1
WARNING
To reduce the risk of fire and risk of lint collecting
in exhaust duct, do not operate dryer without lint
filter in place.
W771
3. Load dryer half full with laundry ( 8.2 kg [18 pounds] ) maximum
dry clothes load). Add fabric softener sheet, if desired.
NOTE: To avoid damage to dryer, do not use more
than one fabric softener sheet per load.
DRY2543N_SVG
4. Close loading door. Dryer will not operate with the door open.
DRY2026N_SVG
Operating Your Dryer
©Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
13 Part No. D514817ENR1

5. If not already on (control lights will be lit), turn on the dryer by
pressing the Power/Cancel buon.
NOTE: You will not be able to press the Start/Pause
button to Pause the cycle until the motor is running. If
the Start/Pause button is pressed while attempting to
run the motor (during the warm-up period), an invalid
keypress tone will sound.
6. Select the Cycle and, if desired, change the Selections and Op-
tions seings. Follow garment manufacturer’s care labels for
recommended temperature seings.
7. Press the Start/Pause buon to begin the cycle.
IMPORTANT: The final part of dryer cycle occurs
without heat (cool down cycle) to ensure that items in
dryer are left at a temperature that ensures that the
items will not be damaged.
NOTE: To stop dryer at any time, open the door or
press the Start/Pause button. To restart dryer, close
door and press the Start/Pause button again.
Optional Drying Rack
A drying rack, Part No. D512082, is available at extra cost
through your Factory Authorized Service Center.
The drying rack can be used in manual cycles only for no-tumble dry-
ing of articles such as tennis shoes, sweaters, stuffed toys or oth-
er delicate items.
DRY2332N_SVGDRY2332N_SVG
Operating Your Dryer
©Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
14 Part No. D514817ENR1

Maintenance
Lubrication
All moving parts are sealed in a permanent supply of lubricant or
are equipped with oilless bearings. Additional lubrication will not be
necessary.
Care of Your Dryer
WARNING
To reduce the risk of an electric shock, serious injury
or death, disconnect the electrical service to the dryer
before cleaning the interior.
W132
Dryer Interior
Wipe the surfaces using a soft cloth and household cleaner or a
non-abrasive paste of powdered laundry detergent and hot water,
followed by a short heat cycle with a load of rags.
To remove crayon or ball point ink off the dryer drum, put the heat
on high and use old rags in the dryer to absorb the crayon or ink. If
unsuccessful, contact the appliance dealer. DO NOT use any chemi-
cals in the dryer.
IMPORTANT: The use of chlorine bleach for removing
any discolorations should be avoided because bleach
could damage the finish.
Cabinet
Wipe the dryer cabinet as needed. If detergent, bleach or other
washing products have been spilled on the dryer, wipe immediately.
Some products will cause permanent damage if spilled on the cabi-
net.
Control Panel
Use only a damp or sudsy cloth for cleaning the control panel. Some
spray pretreat products may harm the finish on the control panel.
DO NOT use products that contain alcohol on the control panel.
Exhaust System
WARNING
To reduce the risk of electric shock, disconnect the
electrical service to the dryer before cleaning.
W043
WARNING
Any disassembly requiring the use of tools must be
performed by a suitably qualified service person.
W299
The exhaust duct should be inspected after one year of use and
cleaned if necessary by a qualified service person to remove any lint
build-up. Inspect and clean exhaust duct every one to two years as
required thereafter.
Every two years a qualified service person should remove all front
panels and vacuum the inside of the dryer
NOTE: This recommended maintenance is not covered
under the terms of the warranty.
The weather hood should be checked frequently to make sure the
dampers move freely, dampers are not pushed in and that nothing
has been set against them.
Keep dryer area clear and free from combustible materials, gasoline
and other flammable vapors and liquids.
Do not obstruct the flow of combustion and ventilation air.
NOTE: Verify proper operation after servicing.
Motor Overload Protector
The dryer’s motor overload protector stops the motor automati-
cally in the event of an overload. The control’s digital display will
show “Er”, “ro” alternately. After cooling, the overload protector will
reset itself.
The control can be cleared by pressing START and the dryer can be
restarted by pressing START again. If overload protector cycles
again, remove the dryer from use and call the service person to cor-
rect the problem.
Maintenance
©Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
15 Part No. D514817ENR1

Lint Filter
The lint filter is located at the front of the dryer in the lower part of
the door opening.
CLEAN THE LINT FILTER BEFORE DRYING EACH LOAD.
Annually remove lint filter and screw to vacuum the duct under it.
DRY2757N_SVG
1
1. Lint Filter
Figure 2
Maintenance
©Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
16 Part No. D514817ENR1

Troubleshooting
Try these troubleshooting tips before making a service call. They
may save you time and money.
Dryer Symptom Possible Cause/Solution
Dryer won’t start • Make sure the power cord is plugged all the way into the electri-
cal outlet.
• Make sure loading door is closed.
• Press Start/Pause buon to start dryer.
• Make sure the laundry room fuse(s) isn’t blown or loose, or cir-
cuit breakers aren’t open.
• Check if motor overload protector has cycled. Wait 10 minutes
and try again.
Dryer won’t heat • Electric dryers only – Some homes may have two fuses or cir-
cuit breakers for an electric dryer; both fuses or circuit break-
ers should be checked. Make sure the laundry room fuse(s) isn’t
blown or loose, or that the circuit breakers aren’t open.
• Make sure control is not in Cooling part of cycle or that the
Temp selection is not set to heat.
• Gas dryer only – Make sure equipment and main gas line valve is
turned on.
• Check exhaust duct to outside to see if it is kinked, blocked or
needs cleaning.
• Check weather hood to make sure flapper moves freely, has not
been pushed in or has not been blocked.
Dryer doesn’t dry clothes satisfactorily • Check exhaust duct to outside to see if it is kinked, blocked or
needs cleaning.
• Check weather hood to make sure flapper moves freely, has not
been pushed in or has not been blocked.
• Auto-Sensing cycle – Adjust Dryness selection.
• Manual cycle - Allow more or less time.
• Clean the lint filter.
• Make sure the load isn’t too small. Small loads may not tumble
properly or dry evenly.
• Check load being dried. Heavy items dried with lightweight
items will not dry as quickly as the rest of the load.
• Refer to Sort section for proper sorting information.
Dryer is noisy • Check dryer for foreign objects (nails, coins, bobby pins, metal,
plastic toys, etc.). Remove items from dryer.
• Make sure dryer is level. Uneven leveling can cause vibration.
• Normal operating sounds include the heat source going on and
off and the humming of air moving through the dryer and ex-
haust system.
Table continues...
Troubleshooting
©Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
17 Part No. D514817ENR1

Dryer Symptom Possible Cause/Solution
Clothes are too wrinkled • Check heat seing. Overdrying can cause wrinkling.
• Check load size. Large loads may not tumble properly and may
cause wrinkling.
Clothes have odor • Check room for odors before drying clothes. Any odor (fried
foods, paint, varnish, cleaners, burning wood, etc.) will transfer
to clothing as the dryer draws air from the room.
• Ventilate room before drying clothes.
Cycle advances too slowly • When in an Auto-Sensing cycle, the time it takes depends on
the type and size of the load being dried. When clothing has
more moisture, the cycle takes longer than when the clothes
are more dry.
Er, ro on digital display • The dryer’s motor overload protector has cycled.
• The control can be cleared by pressing the Start/Pause buon
and the dryer can be restarted by pressing the Start/Pause
buon again.
• If this code is displayed again, remove the dryer from use and
call a service person.
Troubleshooting
©Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
18 Part No. D514817ENR1

Contact Information
If service is required, contact the nearest Factory Authorized
Service Center.
If you are unable to locate an authorized service center or are unsa-
tisfied with the service performed on your unit, contact:
Alliance Laundry Systems
Shepard Street
P.O. Box 990
Ripon, Wisconsin 54971-0990
www.alliancelaundry.com
Phone: [phone]
Date Purchased
Model Number
Serial Number
DRY2030N_SVG
1
1. Serial Plate
When contacting us about your washer, PLEASE GIVE THE MODEL
AND SERIAL NUMBERS. The model and serial numbers are located
on the serial plate. The serial plate will be in the location shown.
Please include a copy of your bill of sale and any service receipts you
have.
If replacement parts are required, contact the source from where
you purchased your unit or call [phone] for the name
and address of the nearest authorized parts distributor.
WARNING
To reduce the risk of serious injury or death, DO NOT
repair or replace any part of the unit or attempt any
servicing unless specifically recommended in the
user-maintenance instructions or in published user-re-
pair instructions that you understand and have the
skills to carry out.
W329
Troubleshooting
©Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
19 Part No. D514817ENR1