Alliance Laundry Systems SH180-QED-SELECT Owner's manual

Installation/Operation/Maintenance
Washer-Extractors
Barrier Washer
Refer to Page 11 for Model Identification
Original Instructions
Keep These Instructions for Future Reference.
CAUTION: Read the instructions before using the machine.
(If this machine changes ownership, this manual must accompany machine.)
www.alliancelaundry.com Part No. D1635ENR5
August 2018

Table of Contents
Safety Information..................................................................................6
Important Safety Instructions........................................................................... 6
Safety Precautions.......................................................................................... 7
Introduction..........................................................................................11
Model Identification ..................................................................................... 11
Serial Plate Location..................................................................................... 11
Manufacturing Date.......................................................................................11
Delivery Inspection....................................................................................... 12
Replacement Parts.........................................................................................13
Customer Service..........................................................................................13
Specification and Dimensions................................................................14
General Specification.................................................................................... 14
Machine Dimensions (Standard Version).........................................................16
Machine Dimensions with Weighing System and Drain Placed underneath the Ma-
chine in the Central Part (on Request)..........................................................24
Machine Dimensions with Weighing System, with Drain Placed underneath the
Machine in the Central Part and with a Handling Base (on Request)...............26
Installation........................................................................................... 28
Handling Transport and Storage..................................................................... 28
Placement into Hygienic Barrier.....................................................................29
Placement into Hygienic Barrier with Guards (on Request)...............................31
Mechanical Installation..................................................................................33
Mechanical Installation without Weighing System and with a Steel Base - Plinth
............................................................................................................ 33
Mechanical Installation with Weighing System (on Request)......................... 34
Mechanical Installation with Weighing System and Drain Placed underneath the
Machine in the Central Part (on Request)................................................. 36
Mechanical Installation with Weighing System, with Drain Placed underneath
the Machine in the Central Part and with a Handling Base (on Request)......38
Drain Connection..........................................................................................39
Drain Connection under the Machine (Standard).......................................... 39
Drain Connection with Weighing System and Drain Placed underneath the Ma-
chine in the Central Part (on Request)...................................................... 40
Side Drain Connection (on Request)............................................................40
Main Drain Channel-pipe...........................................................................42
Water Connections........................................................................................ 43
Connecting Hoses......................................................................................... 44
Recuperated Water Connection.......................................................................45
© Copyright 2018, Alliance Laundry Systems LLC
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed
written consent of the publisher.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
3 Part No. D1635ENR5

Treatment of the Recuperated Water............................................................46
Water Recycling Tank Properties ............................................................... 46
The Use of a Float in the Recycling Tank.....................................................46
Electrical Installation Requirements................................................................47
Residual Current Device - RCD..................................................................48
Supply Protection Device...........................................................................48
Supply Cable............................................................................................ 48
Determining AWG Sizes............................................................................ 49
Machine Protective Earth Connection and Equipotential Bonding.................. 49
Electrical Specification..................................................................................51
Steam Connection.........................................................................................53
Venting........................................................................................................ 53
Liquid Soap Connection................................................................................ 53
Electrical Connection of the Liquid Soap Supply System..................................55
Electronic Controller with Blue PCB and Graphical Display............................. 55
Chemical Injection Supply System................................................................. 56
Operation............................................................................................. 58
Symbols on the Machine................................................................................58
Before Washing............................................................................................ 59
Placing the Laundry into the Machine............................................................. 59
Add Detergents.............................................................................................60
Program Selections....................................................................................... 61
Wash Programs Overview..............................................................................61
Start the Washer............................................................................................61
End of Cycle Indication (on Request)..............................................................62
End of Wash Cycle........................................................................................62
Power Failure............................................................................................... 63
Maintenance and Adjustments..............................................................64
General........................................................................................................ 64
Checking and Maintenance Daily................................................................... 64
Checking and Maintenance Every Three Months............................................. 64
Checking and Maintenance Every Six Months................................................. 64
Adjusting of Safety Switch............................................................................ 65
Belt Replacement and Adjusting Tension........................................................ 65
Lubrication...................................................................................................65
Water Filters.................................................................................................66
Tightening Moments..................................................................................... 66
Replacement Washer Fuses............................................................................ 66
Troubleshooting....................................................................................68
Unblocking of the Door lock in Case of Emergency......................................... 68
How to Remedy Incorrect Position of Drum ................................................... 68
Error Indication Shown on Display.................................................................68
List of Recommended Spare Parts.................................................................. 68
Disposal of Unit.................................................................................... 69
Disconnecting the Machine............................................................................69
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
4 Part No. D1635ENR5

Machine Disposal......................................................................................... 69
Possibility of the Machine Disposal by the Specialized Company.................. 69
Possibility of the Machine Liquidation by Own Potential.............................. 69
China Restriction of hazardous substances (RoHS)............................... 70
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
5 Part No. D1635ENR5

Safety Information
Important Safety Instructions
WARNING
To reduce the risk of fire, electric shock, serious in-
jury or death to persons when using your washer,
follow these basic precautions:
W023
• Read all instructions before using the washer.
• Install the washer according the INSTALLATION instruc-
tions. Refer to the EARTHING instructions in the INSTAL-
LATION manual for the proper earthing of the washer. All
connections for water, drain, electrical power and earthing
must comply with local codes and be made by licensed per-
sonnel when required. It is recommended that the machine be
installed by qualified technicians.
• Do not install or store the washer where it will be exposed to
water and/or weather.
• To prevent fire and explosion, keep the area around machine
free from flammable and combustible products. Do not add
the following substances or textiles containing traces of the
following substances to the wash water: gasoline, kerosene,
waxes, cooking oils, vegetable oils, machine oils, dry-clean-
ing solvents, flammable chemicals, thinners, or other flamma-
ble or explosive substances. These substances give off vapors
that could ignite, explode or cause the fabric to catch fire by
itself.
• Under certain conditions, hydrogen gas may be produced in a
hot water system that has not been used for two weeks or
more. HYDROGEN GAS IS EXPLOSIVE. If the hot water
system has not been used for such a period, before using a
washing machine or combination washer-dryer, turn on all hot
water faucets and let the water flow from each for several mi-
nutes. This will release any accumulated hydrogen gas. The
gas is flammable, do not smoke or use an open flame during
this time.
• To reduce the risk of an electric shock or fire, DO NOT use an
extension cord or an adapter to connect the washer to the elec-
trical power source.
• Do not allow children to play on or in the washer. Close su-
pervision of children is necessary when the washer is used
near children. This appliance is not intended for use by young
children or infirm persons without supervision. Young chil-
dren should be supervised to ensure that they do not play with
the appliance. This is a safety rule for all appliances.
• DO NOT reach and/or climb into the tub or onto the washer,
ESPECIALLY if the wash drum is moving. This is an immi-
nently hazardous situation that, if not avoided, will cause se-
vere personal injury or death.
• Never operate the washer with any guards, panels and/or parts
removed or broken. DO NOT bypass any safety devices or
tamper with the controls.
• Use washer only for its intended purpose, washing textiles.
Never wash machine parts or automotive parts in the ma-
chine. This could result in serious damage to the basket or
tub.
• Use only low-sudsing, no-foaming types of commercial deter-
gent. Be aware that hazardous chemicals may be present.
Wear hand and eye protection when adding detergents and
chemicals. Always read and follow manufacturer’s instruc-
tions on packages of laundry and cleaning aids. Heed all
warnings or precautions. To reduce the risk of poisoning or
chemical burns, keep them out of the reach of children at all
times (preferably in a locked cabinet).
• Do not use fabric softeners or products to eliminate static un-
less recommended by the manufacturer of the fabric softener
or product.
• Always follow the fabric care instructions supplied by the tex-
tile manufacturer.
• Loading door MUST BE CLOSED any time the washer is to
fill, tumble or spin. DO NOT bypass the loading door switch
by permitting the washer to operate with the loading door
open. Do not attempt to open the door until the washer has
drained and all moving parts have stopped.
• Be aware that hot water is used to flush the supply dispenser.
Avoid opening the dispenser lid while the machine is running.
• To reduce the risk of burning, do not touch the door glass
when the machine is running, especially after the heating
phase of the wash cycle.
• Do not attach anything to the supply dispenser’s nozzles, if
applicable. The air gap must be maintained.
• To avoid machine corrosion and component failure, do not
use corrosive chemicals in the washer-extractor. Warranty
claims related to damage caused by corrosive chemicals will
be denied.
• Do not operate the machine without the water reuse plug or
water reuse system in place, if applicable.
• Be sure water connections have a shut-off valve and that fill
hose connections are tight. CLOSE the shut-off valves at the
end of each wash day.
• Keep washer in good condition. Bumping or dropping the
washer can damage safety features. If this occurs, have wash-
er checked by a qualified service person.
• DANGER: Before inspecting or servicing machine, power
supply must be turned OFF. The servicer needs to wait for at
least 3 minutes after turning the power OFF and needs to
check for residual voltage with a voltage meter. The inverter
capacitor or EMC filter remains charged with high voltage for
some time after powering OFF. This is an imminently hazard-
ous situation that, if not avoided, will cause severe personal
injury or death.
Safety Information
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
6 Part No. D1635ENR5

• Do not repair or replace any part of the washer, or attempt any
servicing unless specifically recommended in the user-mainte-
nance instructions or in published user-repair instructions that
the user understands and has the skills to carry out. ALWAYS
disconnect the washer from electrical, power and water sup-
plies before attempting any service.
• Disconnect the power cord by grasping the plug, not the cord.
Replace worn power cords and/or loose plugs. If the supply
cord is damaged, it must be replaced by a special cord or as-
sembly available from the service agent.
• Before the washer is removed from service or discarded, re-
move the door to the washing compartment.
• Failure to install, maintain, and/or operate this washer accord-
ing to the manufacturer’s instructions may result in conditions
which can produce bodily injury and/or property damage.
NOTE: The WARNINGS and IMPORTANT SAFETY IN-
STRUCTIONS appearing in this manual are not meant
to cover all possible conditions and situations that may
occur. Common sense, caution and care must be exer-
cised when installing, maintaining, or operating the
washer.
Always contact your dealer, distributor, service agent or the man-
ufacturer on any problems or conditions you do not understand.
NOTE: All appliances are produced according the EMC-
directive (Electro-Magnetic-Compatibility). They can be
used in restricted surroundings only (comply minimally
with class A requirements). For safety reasons there
must be kept the necessary precaution distances with
sensitive electrical or electronic device(s). These ma-
chines are not intended for domestic use by private
consumers in the home environment.
Safety Precautions
WARNING
Save these instructions for later use. Failure to com-
ply with the instructions may lead to incorrect use of
the appliance, and may result in risk of fire, bodily in-
juries or death and/or damage to the laundry and/or
the appliance.
C003
WARNING
Read the important safety instructions in this manual
carefully before operating the appliance. Improper
use of the appliance may cause risk of fire, electrical
shock or serious body injuries or death as well as
serious damage to the appliance.
C244
• Follow the instruction written in manuals and keep the man-
uals in a proper place by the machine for later use.
• Safety instructions included in manuals for personnel operat-
ing the appliance must be printed and posted on a visible
place near the machine in the laundry room.
• The washer extractor is designed for fabrics washing only,
other objects can damage the washer and can cause damage or
injuries.
• If the machine is used for special applications follow the in-
structions and warning to avoid person injury.
• The manufacturer is not responsible for the damage to the
fabrics that are washed by an inappropriate washing method.
• Always follow the instructions and/or warnings that are stated
on the fabrics, washing products or cleaning products men-
tioned by the manufacturer.
• The washer must be set up in accordance with the instruc-
tions. All drain, inlet, electrical connections, ventilation,
groundings and other connections must be done in according
to the installation manual, in compliance with the local stand-
ards done by qualified technicians with proper authorization.
• The valid standards for connecting to the local power network
(TT,TN,IT,…) must be followed. In the standard execution,
the appliance may not be suitable for connecting to an IT sup-
ply system. Contact your commercial distributor for assis-
tance.
• All appliances are produced according the EMC-directive
(Electro-Magnetic-Compatibility). They can be used in re-
stricted surroundings only (comply minimally with class A re-
quirements). For safety reasons there must be kept the neces-
sary precaution distances with sensitive electrical or electron-
ic device(s). These machines are not intended for domestic
use by private consumers in the home environment.
• Do not change the parameters of the frequency inverter. This
can cause serious injury, fire, washer damage, etc.
• During transportation and storage never use excessive forces
on the packing because components can be damaged protrud-
ing the contour line of the appliance.
• Use copper conductors only. This appliance must be connect-
ed to a supply circuit to which no lighting units or general-
purpose receptacles are connected.
• Any changes concerning the installation which are not descri-
bed in this Installation Manual must be approved by the sup-
plier or manufacturer. Otherwise, the supplier and manufac-
turer are not responsible for potential injuries to operators or
for any damages. Interventions in the appliance execution or
functions are not allowed, and the manufacturer refuses any
responsibility in such cases.
• The washer extractor must be installed on level. If not, the
washer may become unbalanced during extraction and, al-
though fitted with an unbalance safety, the washer may be-
come seriously damaged what may result in bodily injuries.
• Never put the washer in operation when the transporting bra-
ces are not removed. The washer should always be tested be-
fore use.
Safety Information
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
7 Part No. D1635ENR5

• It is possible that there are residues of products used during
the production process in the new washer. These residues
could cause stains on your laundry. Therefore, you must first
run at least 1 hot wash with old rags before using for your
normal laundry.
• Keep the appliance top and surface and the area around clean
and clear of combustible or flammable products.
• The use of hypochlorite will cause corrosion which may cause
component failure under certain circumstances.
• The warranty of the machine cannot be accepted in case cor-
rosion was caused by chlorine and chlorine compounds im-
pact.
• The washer extractor is not designed for work which may cre-
ate an explosive atmosphere inside the machine and will not
be used for this purpose.
• Do not expose the washer extractor to the weather, extreme
low or high temperature and humidity.
• Do not store flammable materials around the appliances. De-
fine the dangerous areas in the laundry room and obstruct an
admission to them during appliances operating.
• Do not wash articles that have been previously cleaned in,
wash in soaked in, or spotted with gasoline, dry-cleaning sol-
vents, or other flammable or explosive substances as they
give off vapors that could ignite or explode. Such fabrics must
first be washed by hand and air dried.
• Do not add gasoline, dry-cleaning solvents, or other flamma-
ble or explosive substances to the wash water. These substan-
ces give off vapors that could ignite or explode.
• TEMPERATURE IN WASHING MACHINE TUB: The elec-
tronic controller uses the temperature sensor in the tub to con-
trol the temperature of the washing bath. There are a lot of
things that have influence on the temperature measurement.
Therefore the temperature control of the washing bath is not
very precise.
• Always strictly comply with the instructions that are written
on the laundry chemicals-, laundry aids-, dry-cleaning sol-
vents- and disinfectants packaging to avoid personal injury.
• Do not tamper the washer-extractor controls and do not by-
pass the safety instructions and the warnings.
• By danger turn off the main switch or other emergency dis-
connection devices.
• Do not put some part on the soap dispenser lid to held it open
by filling or when the machine operates.
• Do not open the soap dispenser lid after the machine is start-
ed. The discharge or splashing of hazardous liquid can cause
serious scalding and burning.
• Do not operate the appliance when parts are broken or miss-
ing or when covers are open. The appliance must not be oper-
ated until the fixed guards are put correctly in place.
• The appliance must not be stored, installed or exposed to the
weather, extreme low or high temperature and humidity lev-
els. Do not hose down the washer. NEVER allow the appli-
ance to get wet. Avoid damp conditions where water or mois-
ture could run down the walls and covers of the washer or
cover the floor around the washer. Do not install the washer
above an open gutter. Close any nearby gutters so that waste
water steam cannot collect near/inside the washer.
• Check the functioning of the door lock mechanism on regular
base. NEVER bypass the doorlock mechanism.
• Disconnect the power and close all water and steam supply
before cleaning, servicing and at the end of each operating
day.
• Vapour or hot air can escape out of the venting. Do not cover
the vent but protect it sufficiently. It serves air gap and as a
vapor outlet to prevent pressure building in the washer.
• Do not repair or replace any part of the appliance or attempt
any servicing unless specifically recommended in the service
manual or published user-repair instructions that you under-
stand and have the skills to carry out. Only qualified service
personnel may open the appliance to carry out servicing.
• Information contained in this manual is intended for use by a
qualified service technician familiar with proper and safe pro-
cedures to be followed when repairing an electrical appliance.
All tests and repairs should be performed by a qualified serv-
ice technician equipped with proper tools and measuring devi-
ces. All component replacements should be made by a quali-
fied service technician using only factory approved replace-
ment parts.
• Improper assembly or adjustment may occur if service or re-
pair is attempted by persons other then qualified service tech-
nicians or if parts other then approved replacement parts are
used. Improper assembly or adjustment can create hazardous
conditions.
• There can be a risk of injury or electrical shock while per-
forming services or repairs. Injury or electrical shock can be
serious or even fatal. Consequently, extreme caution should
be taken while performing voltage checks on individual com-
ponents or a product. PLEASE NOTE: Except as necessary to
perform a particular in servicing a product, the electrical pow-
er supply should ALWAYS be disconnected when servicing a
product.
• All industrial (OPL - On Premise Laundry) washers are de-
signed for use in Laundry with professionally trained attend-
ants.
• Before the appliance is removed from service or discarded,
remove the door.
• Any Water or Steam Leaks Must Be Repaired Immediately.
Closed supply immediately.
• If any problems or failures should arise, immediately contact
your dealer, serviceman or manufacturer.
• The manufacturer reserves the right to change the manuals
without previous notice.
• Norm IEC335 is applied for machines with a net usable cage
volume between 60 and 150 l. Norm EN60204-1 is used for a
net usable cage volume above 150 l.
Safety Information
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
8 Part No. D1635ENR5

WARNING
If the installed appliance operate with coin, token or
similar operation for use in self-service situations,
then the owner-installer must provide a remote-locat-
ed emergency stop device. This device must be
placed in such a way that it is easy and safely acces-
sible for the users. The emergency stop device takes
care that at least the control circuit of the appliance
is interrupted.
C004
WARNING
Do not touch the doorglass until cycle has been
completed. Do not open door until cylinder remains
stopped and water has been drained from cylinder.
Do not put articles soiled with explosive solvents
and/or dangerous chemical products in the machine.
This machine should not be used by children. Do not
let children play in, on, or around the machine. Be-
fore turning the machine “on”, make sure that there
are no people or animals present in or around the
machine.
C005
WARNING
Original or identical parts must be used for replace-
ment in this machine. After servicing replace and se-
cure all panels in the original way. Take these meas-
ures for continued protection against electrical
shock, injury, fire and/or property damage.
C007
WARNING
Looking at the machine from the front, drum rotation
during extraction must be clockwise.
C008
WARNING
This appliance must be connected to a grounded
metal, permanent wiring system, and additionally an
equipment-grounding conductor must be run with
the circuit conductors and connected to the equip-
ment-grounding terminal or lead on the appliance.
C180
WARNING
In order to minimize the risk of fire, electrical shock
and injury, THIS WASHER MUST BE PROPERLY
GROUNDED. Never plug in or direct-wire an appli-
ance unless it is properly grounded in accordance
with all local and national codes.
If more appliances in the same location, mutual
grounding must be applied where possible.
C181
WARNING
Although the appliance may be in the “off” position,
there is still electrical power to the switch supply ter-
minals.
C186
WARNING
When power supply has been switched off wait for at
least 10 minutes before starting inspection or servic-
ing the washer. Before starting inspection of fre-
quency inverter, check for residual voltage across
main circuit terminals + and -. This voltage must be
below 30 VDC before you can access the inverter for
inspection.
C187
WARNING
Do not allow children to play on, in or around the ap-
pliance at any time. Close supervision of children.
C188
WARNING
If the door safety lock does not work, do not use
washer until the door lock mechanism is repaired.
C226
Safety Information
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
9 Part No. D1635ENR5

WARNING
Follow all valid basic safety rules and laws. The in-
structions in this manual cannot account for every
possible dangerous situation. They must be general-
ly understood. Caution and care are factors which
can not included in the design of the appliance and
all persons who install, operate or maintain the appli-
ance must be qualified and familiar with the operat-
ing instructions. It is up to the user to take proper
care when operating the appliance.
C227
WARNING
Do not remove warning signs placed on the appli-
ance. Observe signs and labels to avoid personal in-
juries. Safety labels appear at crucial locations on
the appliance. Failure to maintain legible safety la-
bels could result in injury to the operator or service
technician.
C228
CAUTION
Machine with weighing system: never carry load sen-
sors by their cables! Avoid electric welding near the
load sensors! An impact might cause permanent
damage to the load sensors! Avoid unequal load dis-
tribution between the load sensors when putting the
machine down. When the power of the machine is
switched on, the system needs a 10-minutes warm-
up time. This is important when the power has been
off for more than five minutes. Ignoring warm-up
might result in a major error in weighing.
C229
WARNING
The recycling tank must be installed by qualified and
authorised technicians only. The installation must be
done in accordance with all local standards and reg-
ulations.
C230
WARNING
Never interfere with the setting of the door handle.
Never try to modify the setting or repair the handle!
Any interference with its setting may lead to serious
risk for the operator! A damaged or incorrectly func-
tioning door handle must always be immediately re-
placed with a new original part.
C014
Safety Information
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
10 Part No. D1635ENR5

Introduction
Model Identification
Information in this manual is applicable to these models:
Models
SH180_QED-SELECT
SH240_QED-SELECT
SH280_QED-SELECT
SHB0180D
SHC180D
SHC240D
SHC280D
SHG0180D
SHG0240D
SHG0280D
SHH180D
SHH240D
SHH280D
SHU0180D
SHU0240D
SHU0280D
SHU180D
SHU240D
SHU280D
SHX180D
SHX240D
SHX280D
SHY180D
SHY240D
SHY280D
UH180_PROFORM
UH240_PROFORM
UH280_PROFORM
UHB0180I
UHC180I
UHC240I
UHC280I
UHG0180I
UHG0240I
UHG0280I
UHH180I
UHH240I
UHH280I
UHU0180I
UHU0240I
UHU0280I
UHU180I
UHU240I
UHU280I
UHX180I
UHX240I
UHX280I
UHY180I
UHY240I
UHY280I
Serial Plate Location
1. Serial plate
Figure 1
The serial plate is located on the side of the machine and on the
frame inside the machine.
Always provide the machine serial number when ordering parts
or when seeking technical assistance.
Manufacturing Date
The manufacturing date for your unit can be found on the serial
number. The last two characters indicate first the year and then
the month. Refer to Table 1 and Table 2 . For example, a unit with
serial number 520I000001DK was manufactured in May 2015.
Manufacturing Date - Year
Year Serial Number Character
2009 P
2010 R
2011 T
2012 V
2013 X
2014 B
2015 D
2016 F
2017 H
2018 K
Table 1 continues...
Introduction
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
11 Part No. D1635ENR5

Manufacturing Date - Year
Year Serial Number Character
2019 M
2020 Q
Table 1
Manufacturing Date - Month
Month Serial Number Character
January A or B
February C or D
March E or F
April G or H
May J or K
June L or M
July N or Q
August P or S
September R or U
October T or W
November V or Y
December X or Z
Table 2
Introduction
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
12 Part No. D1635ENR5

Delivery Inspection
Upon delivery, visually inspect crate, protective cover, and unit
for any visible shipping damage. If signs of possible damage are
evident, have the carrier note the condition on the shipping pa-
pers before the shipping receipt is signed, or advise the carrier of
the condition as soon as it is discovered.
Replacement Parts
If literature or replacement parts are required, contact the source
from which the machine was purchased or contact Alliance Laun-
dry Systems at [phone] for the name and address of the
nearest authorized parts distributor.
Customer Service
For technical assistance, contact your local distributor or contact:
Alliance Laundry Systems
Shepard Street
P.O. Box 990
Ripon, Wisconsin 54971-0990
U.S.A.
www.alliancelaundry.com
Phone: [phone]
Ripon, Wisconsin
Introduction
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
13 Part No. D1635ENR5

Specification and Dimensions
General Specification
Machine kg / lb / L 18 / 40 / 180 24 / 55 / 240 28 / 65 / 280
Inner Drum Dimensions
Volume, ft3 [L] 6.4 [180] 8.5 [240] 9.9 [280]
Depth, in. [mm] 16.10 [409] 21.42 [544] 25.16 [639]
Diameter, in. [mm] 29.53 [750] 29.53 [750] 29.53 [750]
Drum Speed
Wash, (RPM) 42 42 42
Extraction, (RPM) 939 939 914
G-Factor 370 370 350
Heating
Electrical, (kW) 12 / 18 18 21.9
Steam pressure, kPa [bar] 300 - 800 [3 - 8]
Hot water, °F [°C] 194 [90]
Weight and Shipping Dimensions
Net weight, lb [kg] 948 [430] 1015 [460] 1080 [490]
Shipping weight, lb [kg] 1070 [485] 1135 [515] 1213 [550]
Shipping height, in. [mm] 63.39 [1610] 63.39 [1610] 63.39 [1610]
Shipping width, in. [mm] 39.76 [1010] 44.49 [1130] 48.82 [1240]
Shipping depth, in. [mm] 48.62 [1235] 48.62 [1235] 48.62 [1235]
Dimensions (Standard) Refer to Machine Dimensions (Standard Version).
Drive Train Information
Motor size, HP [kW] 2.95 [2.20] 4.02 [3] 4.02 [3]
Connection
Water valves connection BSP, (in) 3 x ¾
Water pressure, (kPa) 100 - 800
Recommended water pressure, (kPa) 300 - 500
Capacity, (l/min) at 1-8 bar 66-188
Drain valve outer ø in. [mm] 3 [76]
Flow amount with drain valve, (l/
min)
210
Table 3 continues...
Specification and Dimensions
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
14 Part No. D1635ENR5

Machine kg / lb / L 18 / 40 / 180 24 / 55 / 240 28 / 65 / 280
Steam valve connection BSP, (in) ½
General Data
Ambient temperature, °F [°C] 41-95 [5-35]
Relative humidity 30% to 90% without condensation
Height above sea level, ft [m] to 3281 [1000]
Storage temperature and shipment, °F
[°C]
34-131 [1-55]
Noise Emissions
Wash sequence, (dB) 45 50 N/A
Extract sequence, (dB) 67 68 N/A
Floor Load Data
Maximum static load on floor with-
out plinth, (kN)
5.32 5.85 6.28
Maximum dynamic load on floor,
(kN)
4.5 ± 0.65 4.9 ± 1.0 5.4 ± 1.05
Frequency of dynamic load, (Hz) 15.65 15.65 15.25
Table 3
Specification and Dimensions
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
15 Part No. D1635ENR5

Machine Dimensions (Standard Version)
Loading Side (Dirty Side)
18 kg / 40 lb / 180 L
24 kg / 55 lb / 240 L
28 kg / 65 lb / 280 L
CZB33N
A
3
1
2
3
B
C
E
F
D
1. Control panel
2. Emergency stop button “CENTRALSTOP”
3. Loading side door (dirty side). For door opening dimensions refer to Table 4 .
Figure 2
Door Opening Dimensions (Loading Side)
Specification
Machine kg / lb / L
18 / 40 / 180 24 / 55 / 240 28 / 65 / 280
Width, in. [mm] 14.8 [376] 19.52 [496] 19.52 [496]
Height, in. [mm] 12.79 [325] 12.79 [325] 12.79 [325]
Table 4
Specification and Dimensions
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
16 Part No. D1635ENR5

Machine Dimensions (Loading Side), in. [mm]
Specification
Machine kg / lb / L
18 / 40 / 180 24 / 55 / 240 28 / 65 / 280
A33.46 [850] 38.18 [970] 42.52 [1080]
B1.22 [31] 1.22 [31] 1.22 [31]
C35.43 [900] 40.16 [1020] 44.49 [1130]
D25.79 [655] 26.58 [675] 26.38 [670]
D - version with weighing sys-
tem or with a steel base
31.69 [805] 32.48 [825] 32.28 [820]
E56.02 [1423] 56.02 [1423] 56.02 [1423]
E - version with weighing sys-
tem or with a steel base
61.93 [1573] 61.93 [1573] 61.93 [1573]
F57.28 [1455] 57.28 [1455] 57.28 [1455]
F - version with weighing sys-
tem or with a steel base
63.19 [1605] 63.19 [1605] 63.19 [1605]
Table 5
Specification and Dimensions
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
17 Part No. D1635ENR5

Left Side (View from Loading Side)
1 2 3 4
A
B
C
D
CZB24N
5
1. Main switch
2. Heating change-over switch (electric heating, steam heating), (on request)
3. USB port, (on request)
4. Fuses
5. PC programming connection (on request)
Figure 3
Machine Dimensions (Left Side), in. [mm]
Specification
Machine kg / lb / L
18 / 40 / 180 24 / 55 / 240 28 / 65 / 280
A40.35 [1025] 40.35 [1025] 40.35 [1025]
B10.91 [277] 10.91 [277] 10.91 [277]
C45.08 [1145] 45.08 [1145] 45.08 [1145]
D44.37 [1127] 44.37 [1127] 44.37 [1127]
Table 6 continues...
Specification and Dimensions
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
18 Part No. D1635ENR5

Machine Dimensions (Left Side), in. [mm]
Specification
Machine kg / lb / L
18 / 40 / 180 24 / 55 / 240 28 / 65 / 280
D - version with weighing sys-
tem or with a steel base
50.27 [1277] 50.27 [1277] 50.27 [1277]
Table 6
Specification and Dimensions
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
19 Part No. D1635ENR5

View from Above
3
4
12
A
B
D
C
E F
G
D
I
J
I
J
K L O P Q RS T
M N
U
CZB25N
5 6 7 8 9 10 11 12 13 14 15
1. Standard
2. Drain, (standard 1 x 3 in.)
3. Drain into the water recycle, (1 x 3 in., on request for water recycle)
4. Soap dispenser
5. Connector for connecting visual end of cycle indication, unloading side (clean side), (on request)
6. Connector for connecting visual end of cycle indication, loading side (dirty side), (on request)
7. Electrical connection to liquid soap pumps
8. Electrical supply connection
9. Cable inlet - cable for control of the valve or pump of water from the water recycle (on request for water recycle)
10. Lubrication system – external placement (on request). Refer to Lubrication.
11. Hot water
12. Cold water hard
13. Cold water soft
14. Additional inlets of liquid soap detergents, placed on the panel (on request)
15. Steam connection (steam version) ½ in.
Figure 4
Specification and Dimensions
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
20 Part No. D1635ENR5