Alliance Laundry Systems CHM1766C Owner's manual

Programming
www.comlaundry.com
Washer-Extractors
Cabinet Hardmount
A-Series Microcomputer for OPL Models
2 Speed and Variable-Speed
Refer to Page 2 for Model Identification
CHM1766C
<
<
12
34
56
CHM1766C
Part No. F232224R1
May 2008
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232225
© Copyright 2008, Alliance Laundry Systems LLC
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any
means without the expressed written consent of the publisher.
1
Table of
Contents
Model Identification ........................................................................... 2
Safety Information.............................................................................. 3
Explanation of Safety Messages........................................................... 3
Important Safety Instructions ............................................................... 3
Safety Decals ........................................................................................ 5
Operator Safety..................................................................................... 6
Programming ...................................................................................... 7
Entering Program Mode ....................................................................... 7
Cycle and Error Count .......................................................................... 7
Setup Mode........................................................................................... 7
Programming Cycle Segments ............................................................. 8
Options for Each Segment.................................................................... 10
To Edit an Entire Wash Cycle Formula................................................ 13
Agitation for the Cycle..................................................................... 13
Wash 1 – Wash 5 ............................................................................. 13
Temperature Controlled Fill ............................................................ 14
Rinse 1 – Rinse 6 ............................................................................. 14
Temperature Controlled Fill ............................................................ 15
Abnormal Conditions............................................................................ 16
Door Open During Operation .......................................................... 16
Excessive Fill Time.......................................................................... 16
Out of Balance ................................................................................. 16
Door Will Not Open......................................................................... 16
Excessive Drain Time ...................................................................... 16
Temperature Probe Sensor Problem ................................................ 16
Clean Filter LED On........................................................................ 16
Test Cycle ............................................................................................. 16
Domestic Cycle Charts Custom............................................................ 19
Cycles 1 - 24 .................................................................................... 19
International Cycle Charts Custom....................................................... 21
Cycles 31 - 46 .................................................................................. 21

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F232224
2
Model Identification
Information in this manual is applicable to these
models:
HC80ANV SC40AN2 SC60ANF UC30AN2 UC60ANF
SC125ANV SC40ANV SC80ANV UC40AN2 UC60ANV
SC20AN2 SC60ANV UC125ANV UC40ANV UC80ANV
SC30AN2 SC60AN2 UC20AN2 UC60AN2

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 3
F232224
Safety Information
Explanation of Safety Messages
Precautionary statements (“DANGER,” “WARNING,”
and “CAUTION”), followed by specific instructions,
are found in this manual and on machine decals. These
precautions are intended for the personal safety of the
operator, user, servicer, and those maintaining the
machine.
Additional precautionary statements (“IMPORTANT”
and “NOTE”) are followed by specific instructions.
IMPORTANT: The word “IMPORTANT” is used
to inform the reader of specific procedures where
minor machine damage will occur if the procedure
is not followed.
IMPORTANT: The word “NOTE” is used to
communicate installation, operation, maintenance
or servicing information that is important but not
hazard related.
Important Safety Instructions
1. Read all instructions before using the washer.
2. Refer to the GROUNDING INSTRUCTIONS in
the INSTALLATION MANUAL for the proper
grounding of the washer.
3. Do not wash textiles that have been previously
cleaned in, washed in, soaked in, or spotted with
gasoline, kerosene, waxes, cooking oils, dry-
cleaning solvents, or other flammable or
explosive substances as they give off vapors that
could ignite or explode.
4. Do not add gasoline, dry-cleaning solvents, or
other flammable or explosive substances to the
wash water. These substances give off vapors that
could ignite or explode.
5. Under certain conditions, hydrogen gas may be
produced in a hot water system that has not been
used for two weeks or more. HYDROGEN GAS
IS EXPLOSIVE. If the hot water system has not
been used for such a period, before using a
washing machine or combination washer-dryer,
turn on all hot water faucets and let the water
flow from each for several minutes. This will
release any accumulated hydrogen gas. The gas is
flammable; do not smoke or use an open flame
during this time.
6. Do not allow children to play on or in the washer.
Close supervision of children is necessary when
the washer is used near children. This is a safety
rule for all appliances.
7. Before the washer is removed from service or
discarded, remove the door to the washing
compartment.
8. Do not reach into the washer if the wash drum is
moving.
DANGER indicates the presence of a
hazard that will cause severe personal
injury, death, or substantial property
damage if the danger is ignored.
DANGER
WARNING indicates the presence of a
hazard that can cause severe personal
injury, death, or substantial property
damage if the warning is ignored.
WARNING
CAUTION indicates the presence of a
hazard that will or can cause minor
personal injury or property damage if the
caution is ignored.
CAUTION
To reduce the risk of fire, electric shock,
serious injury or death to persons when
using your washer, follow these basic
precautions: W023
WARNING

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Safety Information
F232224
4
9. Do not install or store the washer where it will be
exposed to water and/or weather.
10. Do not tamper with the controls.
11. Do not repair or replace any part of the washer, or
attempt any servicing unless specifically
recommended in the user-maintenance
instructions or in published user-repair
instructions that the user understands and has the
skills to carry out.
12. To reduce the risk of an electric shock or fire, DO
NOT use an extension cord or an adapter to
connect the washer to the electrical power source.
13. Use washer only for its intended purpose,
washing textiles.
14. Never wash machine parts or automotive parts in
the machine. This could result in serious damage
to the basket.
15. ALWAYS disconnect the washer from electrical
supply before attempting any service. Disconnect
the power cord by grasping the plug, not the cord.
16. Install the washer according to the
INSTALLATION INSTRUCTIONS. All
connections for water, drain, electrical power and
grounding must comply with local codes and be
made by licensed personnel when required.
17. To reduce the risk of fire, textiles which have
traces of any flammable substances such as
vegetable oil, cooking oil, machine oil,
flammable chemicals, thinner, etc. or anything
containing wax or chemicals such as in mops and
cleaning cloths, must not be put into the washer.
These flammable substances may cause the
fabric to catch on fire by itself.
18. Do not use fabric softeners or products to
eliminate static unless recommended by the
manufacturer of the fabric softener or product.
19. Keep washer in good condition. Bumping or
dropping the washer can damage safety features.
If this occurs, have washer checked by a qualified
service person.
20. If the supply cord is damaged, it must be replaced
by a special cord or assembly available from the
manufacturer or its service agent.
21. Be sure water connections have a shut-off valve
and that fill hose connections are tight. CLOSE
the shut-off valves at the end of each wash day.
22. Loading door MUST BE CLOSED any time the
washer is to fill, tumble or spin. DO NOT
bypass the loading door switch by permitting the
washer to operate with the loading door open.
23. Always read and follow manufacturer’s
instructions on packages of laundry and cleaning
aids. Heed all warnings or precautions. To reduce
the risk of poisoning or chemical burns, keep
them out of the reach of children at all times
(preferably in a locked cabinet).
24. Always follow the fabric care instructions
supplied by the textile manufacturer.
25. Never operate the washer with any guards and/or
panels removed.
26. DO NOT operate the washer with missing or
broken parts.
27. DO NOT bypass any safety devices.
28. Failure to install, maintain, and/or operate this
washer according to the manufacturer’s
instructions may result in conditions which can
produce bodily injury and/or property damage.
NOTE: The WARNINGS and IMPORTANT
SAFETY INSTRUCTIONS appearing in this
manual are not meant to cover all possible
conditions and situations that may occur. Common
sense, caution and care must be exercised when
installing, maintaining, or operating the washer.
Any problems or conditions not understood should be
reported to the dealer, distributor, service agent or the
manufacturer.

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Safety Information
5
F232224
IMPORTANT: Ensure that the recommended
clearances for inspection and maintenance
are provided. Never allow the inspection and
maintenance space to be blocked.
Safety Decals
Safety decals appear at crucial locations on the
machine. Failure to maintain legible safety decals
could result in injury to the operator or service
technician.
To provide personal safety and keep the machine in
proper working order, follow all maintenance and
safety procedures presented in this manual. If
questions regarding safety arise, contact the
manufacturer immediately.
Use manufacturer-authorized spare parts to avoid
safety hazards.
This machine must be installed, adjusted,
and serviced by qualified electrical
maintenance personnel familiar with the
construction and operation of this type of
machinery. They must also be familiar
with the potential hazards involved.
Failure to observe this warning may result
in personal injury and/or equipment
damage, and may void the warranty. SW004
WARNING
Install the machine on a level floor of
sufficient strength. Failure to do so may
result in conditions which can produce
serious injury, death and/or property
damage. W703
WARNING
Be careful around the open door,
particularly when loading from a level
below the door. Impact with door edges
can cause personal injury. SW025
CAUTION
Never touch internal or external steam
pipes, connections, or components.
These surfaces can be extremely hot and
will cause severe burns. The steam must
be turned off and the pipe, connections,
and components allowed to cool before
the pipe can be touched. SW014
WARNING

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Safety Information
F232224
6
Operator Safety
To ensure the safety of machine operators, the
following maintenance checks must be performed
daily:
1. Prior to operating the machine, verify that all
warning signs are present and legible. Missing or
illegible signs must be replaced immediately.
Make certain that spares are available.
2. Check door interlock before starting operation of
the machine:
a. Attempt to start the machine with the door
open. The machine should not start with the
door open.
b. Close the door without locking it and attempt
to start the machine. The machine should not
start with the door unlocked.
c. Close and lock the door and start a cycle.
Attempt to open the door while the cycle is in
progress. The door should not open.
If the door lock and interlock are not functioning
properly, call a service technician.
3. Do not attempt to operate the machine if any of
the following conditions are present:
a. The door does not remain securely locked
during the entire cycle.
b. Excessively high water level is evident.
c. Machine is not connected to a properly
grounded circuit.
Do not bypass any safety devices in the machine.
NEVER insert hands or objects into
basket until it has completely stopped.
Doing so could result in serious injury.
SW012
WARNING
Never operate the machine with a
bypassed or disconnected balance
system. Operating the machine with
severe out-of-balance loads could result
in personal injury and serious equipment
damage. SW039
WARNING

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 7
F232224
Programming
NOTE: The machines are factory-programmed
with basic cycles to make the units operational
without programming at the installation.
Entering Program Mode
1. Open machine lid.
2. Locate Program/Run switch on the computer
board. This is accessed through a cutout in the
metal control unit cover. This switch protrudes
from the rear of the electronic control unit cover.
3. Flip switch to the left (as seen from the front of
machine) to enter PROGRAM Mode.
4. Display will show temperature.
Cycle and Error Count
The control logs cycle count (total of all cycles
completed).
1. To read, enter PROGRAM Mode.
2. Press START (Enter) keypad. Display will show
the cycle count.
3. Press START (Enter) keypad. Display will show
certain error conditions that may have been
recorded by the control.
4. Read the information when consulting technical
assistance as needed.
5. Step through the error log by pressing START
keypad repeatedly until display reverts to normal
PROGRAM Mode (“0000” or a temperature).
Setup Mode
NOTE: In SETUP Mode, certain machine
functions can be configured. The settings in this
mode are related to how the machine is equipped
from the factory. Usually, these settings would not
be changed.
NOTE: Enter SETUP Mode through the Program
Mode.
1. Press (6) keypad. Display will show “FAr” or
“CEL”.
NOTE: This selects whether temperatures display
in degrees Fahrenheit (F) or Celsius (C), if control
is equipped with a temperature sensor. Change
selection by pressing ∧or ∨keypad.
NOTE: Changing degrees “FAr” or “CEL” only
has an effect if the control has a temperature probe
connected and/or heat capability.
2. Press START keypad.
3. Select “HEAt” or “noHt”. Change the selection
by pressing the ∧or ∨keypad.
NOTE: If set for “HEAt”, the control has heat
capability enabled. The washer-extractor MUST
have electric or steam heat, and a temperature
probe. If display shows “noHt”, or if the message
“HEAt” or “noHt” does NOT display, the control
does NOT have heat capability.
4. Press START keypad to continue to the next step.
5. Select “AFIL” or “SUP5”. For “SUP5”, a fifth or
sixth supply can be programmed in a cycle step.
“AFIL” allows auxiliary fills to be programmed
to low, medium or high water level in a cycle
step.
6. Press START keypad.
7. Select “tFIL” or “ntFL.” “tFIL” allows a
temperature controlled fill to be programmed for
any segment. Select “ntFL” to disable the
feature.
8. Press START keypad.
9. Select “COOL” or “noCL.” “COOL” enables an
automatic cooldown feature allowing cold water
to flush into wash before a drain if temperature is
140°F (60°C) or above. Select “noCL” to disable
feature.
10. Press START keypad.
11. Select “bEEP” (control sounds beeper during
Add Bleach [Supply 2]) or “nobP” (control does
NOT sound beeper during Add Bleach [Supply
2]). Change selection by pressing ∧or ∨keypad.
12. Press START keypad.
13. Select “Adv” or “noAd”. “Adv” enables the
Rapid Advance feature. Select “noAd” to disable
the feature.
14. Press START keypad.
To avoid personal injury, recommended
inlet water temperature should be no
higher than 125°Fahrenheit (51°Celsius).
W709
WARNING

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Programming
F232224
8
Programming Cycle Segments
The machine has 30 wash cycles available. 26 wash
cycles are pre-programmed. 4 cycles are available for
custom programming. All wash cycles may be edited
as follows.
1. Enter PROGRAM Mode. Refer to Entering
Program Mode section.
2. Press “∧” keypad to enter PROGRAM Mode.
3. Press the cycle number of the cycle to be edited.
Refer to Table 1.
4. Press the START keypad to move into the menu
of options. Refer to Figure 1.
NOTE: While cycle is running, pressing the START
keypad shows the temperature. Pressing the
START keypad a second time displays the cycle.
Pressing the START keypad a third time returns
display to time remaining.
Figure 1
CHM1766C
1Cycle Keypad “1” 11 Door Open LED
2Cycle Keypad “3” 12 Spin Cycle LED
3Cycle Keypad “5” 13 Rinse Cycle LED
4Rapid Advance/Up “∧” Edit 14 Add Bleach LED
5Cycle Keypad “2” 15 Wash Cycle LED
6Cycle Keypad “4” 16 Out-of-Balance Indicator Dot
7Cycle Keypad “6” (Variable-speed only)
8Stop/Down “∨” Edit 17 High Water Level Indicator Dot
9START Keypad 18 Medium Water Level Indicator Dot
10 CLEAN FILTER Indicator LED 19 Low Water Level Indicator Dot
CHM1766C
<
<
12
34
56
1
5
6
7
8
10
2
16 17 18 19
11
12
13
14
15
4
93