ALPHA LITE DL Series User manual

LED LIGHTING FOR UHD BROADCASTING
EST.2008
USER MANUAL
DOWNLIGHT
DL SERIES

1
1. Do not open or disassemble the cover to reduce the risk of electric shock.
2. Please wear safety equipment such as safety helmet during work.
3. Be sure to fix the safety chain on the product when installing and moving.
4. Please install the signs below for people to bypass
when install the product on high truss.
5. The work should be done under the direction of approved specialist
who is trained in safety and mechanical installations.
6. The brightness and color temperature before and after aging may be different.
Safety Information
WARNING

2
Safety Information 1
Contents 2
[Fixture Information]
Fixture Information 3
Dimensions 4
TechnicalSpecifications 7
[Connection and Setting]
Connection Diagram 8
Connect 9
Lighting On 10
Address Setting 11
Contents

3
Fixture Information
- High color rendering of CRI 90 or higher
- COB LED Chip
- Horizontal 360˚, vertical 27˚ angle adjustable
- All-in-one Main drive controller
- RDM network communication possible
- Maintain the last signal when DMX signal is lost
- Dimming curve selectable (Linear & curve dimming)
- KC certification
- Made in Korea

4
Dimensions (DL30)
mm
(inch)
184
(7.2)
184
(7.2)
∅154
(6.1)
∅164
(6.5)
∅150
(5.9)
∅154
(6.1)
∅164
(6.5)

5
Dimensions (DL50)
mm
(inch)
218
(8.6)
148
(5.8)
∅174
(6.9)
∅185
(7.3)
∅170
(6.7)
∅174
(6.9)
∅185
(7.3)

6
Dimensions (DL100)
mm
(inch)
152
(6)
165
(6.5)
∅123
(4.9)
∅250
(9.8)
205
(8)

7
Technical Specifications
DL30 DL50 DL100
Power Consumption 30W 50W 85W
LED Chip White 30~60W CSP LED or COB
LED
White 30~60W CSP LED or COB
LED
White 1000W COB LED
Cut-off Size ø154 ø174 ø210
Beam Angle 15°, 24°, 36°, 60°15°, 24°, 36°, 60°30°, 40°, 65°
Weight (kg/lbs) 1 / 2.2 1.5 / 3.3 2 / 2.44
Power Supply Range AC 100-240V, 50/60Hz
White Light (CCT) 2900K, 3200K, 5600K, 6000K (FCT)
CRI 95~98
Dimming 0~100% 16-bit
Control 3-PIN DMX In and Through
Supported Protocols , DMX512 / DMX512 RDM
(Option) Wireless DMX512, Wireless RDM
Estimated LED Lifetime Over 50,000 hours
▪This specification data isbased on the aging state of the equipment, and the brightness and color temperature before and after aging may be different .

8
Connection Diagram
(Lighting Console)
(Termination
resistance)

9
Connect
▶SMPS –AC connection
Connect 100~220V Free Volt AC input cord to connector
▶SMPS –AC Thru connection
Other controller SMPS can be connected to SMPS connector with AC power cord.
The line of other SMPS match the color and connect to the right hole of the connector.
Brown Yellow-Green Blue
LFG N
Please check the connection when connecting.

10
Lighting On
▶Lighting On/Off : Manual operation without DMX signal
Light on : Dip switch #1 and #10 go down,
The light turn on.
Light off : Dip switch #1 goes up
while the light is on,
the light turns off.
❖In case of malfunction due to DMX communication noise : Solve communication problems by
selecting and turning on/off the dip switch #1 or #2 of the terminating resistor
❖Caution : For terminating resistor setting, only the last controller on the line is operated.
(Other controller dip switches remain off)

11
Address Setting
▶Free Recommended Application
Dip switch value (binary) can be easily converted
DMX Calc (Android)
Dezelectric
DMX Dip (iOS)
Matthias Bauch
▶Initial Setting
Adjust the APP layout to match the controller’s function switch layout.
- When the address is 000, the dip switch must be all up.
- Number 1~9 must be listed in order from the left.
▶Address Setting
Touch the up and down arrows to
set the desired address number.
Then, it will converted to dip switch
value on the screen below.
Dip switch value (binary method) through APP is applied
to the function switch of the controller.
When the address is 000,
the dip switch up and down position change.
1~9 numbers left and right
position change.
(ex. Address : 025)
(ex. Address : 000) (ex. Address : 025)