ALPHA LITE E Series User manual

BASE SOFT LIGHT E SERIES
USER MANUAL
July 2019

Safety Information
1. Do not open or disassemble the cover to reduce the risk of electric shock.
2. Please wear safety equipment such as safety helmet during work.
3. Be sure to fix the safety chain on the product when installing and moving.
4. Please install the signs below for people to bypass
when install the product on high truss.
5. The work should be done under the direction of approved specialist
who is trained in safety and mechanical installations.
WARNING
- 3 -

Contents
Safety Information 3
Contents 4
[Fixture Information]
Fixture Information 5
Fixture Exterior View 6
Dimensions 7
Technical Specifications 11
Photometric Diagram 12
Side Reflection System 13
[Fixture Installation]
Power Connection 14
DMX Connection 15
[LCD Screen Instruction]
Unlocking 16
Main Screen Instruction 17
Setting Screen Instruction 17
[Setting]
Mode Change 18
Channel Mode Change 18
DMX512 Address Setup 20
Brightness (Intensity) Adjust 21
CCT Adjust
(Correlated Color Temperature) 21
Fixture ID Setup and Change 22
LCD Off Setup 23
LCD Rotation Setup 23
RDM Setup 24
Dimming Speed Setup 24
Master Setup 25
Wireless Setup 25
[Error Information]
Temperature Sensor 26
Network Connection 26
[Protocols]
DMX Protocols 27
RDM Protocols 28
- 4 -

Fixture Information
E Series is a flat light source lighting fixture mainly used in
broadcasting studios, and it is excellent in diffusivity,
low in glare and not exposed to elements.
The LED lighting source sets on the side(edge) with reflection and
pattern optical technology applied. It is the best base light to emit
an extremely soft light source without glare.
2,900~6,000K color temperature control function and average 97% or
more high CRI LED light source.
- 5 -

Fixture Exterior View
Stirrup
Smart Touch
LCD Screen
Handle
Connector
Panel
Fixed Knob
- 6 -

mm
(inch)
Dimensions (E1360)
- 7 -

mm
(inch)
Dimensions (E2040)
- 8 -

mm
(inch)
Dimensions (E2440)
- 9 -

mm
(inch)
Dimensions (E3060)
-10 -

Technical Specifications
-11 -
E1360 E2040 (E4) E2440 (E6) E3060 (E8)
Physical Size 774 x 212 x 154mm 571 x 296 x 112mm 571 x 365 x 112mm 777 x 419 x 112mm
Beam Angle 135°
Weight (kg/lbs) 8.6 / 19 6.7 / 14.8 8.2 / 18.1 12 / 26.5
Handling Adjusting Sliding Stirrup, High Strength Tilt Lock
Mounting 16mm / 28mm
Tilt Angle ±270°
Power Supply Range AC 100-240V, 50/60Hz
Power Consumption 150W 150W 200W 300W
White Light (CCT) Full 2,900~6,000K (VCT)
CRI 95~98
Dimming 0~100% 16-bit
Control 5-PIN DMX In and Out, Smart Touch LCD Controller, RDM,
(Option) Wireless DMX512, Wireless RDM
Remote Device Management Supported
Ambient Temperature Operation -20~45°C
IP Rating IP20
Estimated LED Lifetime Over 50,000 hours

Photometric Diagram
-12 -
E1360
E2040
E2440
E3060
343
277
349
548
141
123
148
225
77
69
82
122
45
41
50
76
9

Light
Reflection
Sheet
LGP
(Lamp + Reflector)
Ad Film
Reflection
Sheet
LGP
Side Reflection System
-13 -

1. Observe the proper voltage range
2. If power is supplied outside the range, noise may be generated from the SMPS.
3. If the operating voltage is out of the proper voltage range,
SMPS function may be degraded or damaged.
Power Connection
AC power at 100-240V, 50-60Hz
-14 -
1. POWER ON/OFF SWITCH
2. POWER IN
3. POWER OUT
4. DMX IN
5. DMX OUT
6. USB PORT (for ADMINISTRATOR ONLY)
(Do not connect USB
without administrator's permission.)

3-pin or 5-pin XLR sockets are equipped for DMX input and output, depending on user needs.
Connect the controller to a lighting, or lighting fixture to other lighting fixture.
If user uses a standard DMX controller, the DMX output of the controller can connect directly
to the DMX input of the first fixture in the DMX chain.
User must use an adapter cable for connect the DMX controller to other XLR output.
1-Shield
2-Signal (-)
3-Signal (+)
4-Not Connected
5-Not Connected
Connect the DMX output of the first lighitng fixture in DMX chain to the DMX input of the next fixture,
and connect one output to the input of the next fixture until all fixtures are connected.
In the last lighting fixture, the DMX cable must be end with a terminator(120 Ω resistor)
in DMX output signal (+, -).
1-Shield
2-Signal (-)
3-Signal (+)
4-Not Connected
5-Not Connected
DMX-INPUT
XLR Mounting-plugs
DMX-OUTPUT
XLR Mounting-sockets
DMX Connection
-15 -

Main Screen (Locked) Fixture ID Screen (Locked)
When the fixture is turned on,
the Smart Touch screen automatically locked.
To unlock the touch screen,
touch the finger icon( ) three times.
If you do not touch for 30 seconds,
the lock is reset.
If the power is turned off and then on again
while the fixture ID number screen is displayed,
the fixture ID lock screen will appear.
To unlock the touch screen, touch the exit icon( )
to move to ‘Main Screen (Locked)’, and press
the finger icon( ) three times.
If you do not touch for 30 seconds, the lock is reset.
AB
A
Unlocking
-16 -

Screen Instruction
1 Current Mode Display DMX MODE or USER MODE or SERIAL MODE.
2 Wireless Signal (Option) Wirelss Signal sensitivity is displayed in % only when set to
‘Wireless Enable’.
3 DMX512 Address Display current DMX512 Address.
4 Brightness (Intensity) Displays the brightness value(0~100%) of the equipment.
5CCT (Correlated Color
Temperatue) Displays the color temperature of the equipment.
6 Screen Rotation LCD screen is rotated 180°for each touch.
7 Setting Setting or changing the function of the equipment.
8 Current Channel Mode The current channel mode is displayed.
9 Fixture ID Displays numbers for equipment management.
10 Fixture Current
Temperature
The current temperature of the instrument is detected and
displayed in °C.
11 Equipment Information You can see basic information about the equipment.
12 Brightness Setup Set lighting brightness
13 CCT Setup Set correlated color temperatre
14 DMX512 Address Setup Set channel mode and DMX512 address
15 LCD Off Setup Set LCD Auto off
16 RDM Setup Activate and deactivate RDM communication function
17 Master Setup Activate and deactivate Master function
18 Dimming Speed Setup Set dimming speed
19 Wireless Setup (Option) Activate and deactivate wireless DMX512 function
Main Screen (Unlocked)
Setting Screen
-17 -

- DMX Mode
- User Mode
- Serial Mode
It is used to adjust by DMX512 signal.
It is used when the user directly manipulates the equipment.
It is used for maintenance.
:
:
:
■DMX Mode → User Mode
■User Mode →DMX Mode
When in DMX mode, user can change to user mode by adjusting the brightness in 'Setting - Brightness'.
When in User mode, user can change to DMX mode
through the 'Setting - DMX512 - Channel selection - DMX address'.
[Setting] Mode Change
-18 -

■Channel Mode Change
User can change the channel by selecting 'Current channel mode' in main screen
or ‘DMX512 - Channel selection - DMX address' in setting.
Pressing the icon in 'Channel Mode' displays information for each channel.
OR
- 1 (1 Ch mode) : Dimming
- 2 (2 Ch mode) : Dimming, CCT
[Setting] Channel Mode Change
-19 -

■DMX512 Address Setup in the Main Screen
Touch 'DMX512 Address' on the main screen to switch to the input window.
001~512 value can be entered. Press icon to save the DMX512 adress and move to the main screen.
Also, the value can changed by RDM. * The number blinks when the connection is disconnected.
Touch 'DMX512 Setup –Channel Mode' on the Setting screen to switch to the input window.
001~512 value can be entered. Press icon to save the DMX512 adress and move to the main screen.
Also, the value can changed by RDM. * The number blinks when the connection is disconnected.
■DMX512 Address Setup in Setting
[Setting] DMX512 Address Setup
-20 -